Frequency Division Duplex Research Articles

DGD-CNet: Denoising Gated Recurrent Unit with a Dropout-Based CSI Network for IRS-Aided Massive MIMO Systems.

For the deployment of Sixth Generation (6G) networks, integrating Massive Multiple-Input Multiple-Output (Massive MIMO) systems with Intelligent Reflecting Surfaces (IRS) is highly recommended due to its significant benefits in reducing communication losses for Non-Line-of-Sight (NLoS) conditions. However, the use of passive IRS presents challenges in channel estimation, mainly due to the significant feedback overhead required in Frequency Division Duplex (FDD)-based Massive MIMO systems. To address these challenges, this paper introduces a novel Denoising Gated Recurrent Unit with a Dropout-based Channel state information Network (DGD-CNet). The proposed DGD-CNet model is specifically designed for FDD-based IRS-aided Massive MIMO systems, aiming to reduce the feedback overhead while improving the channel estimation accuracy. By leveraging the Dropout (DO) technique with the Gated Recurrent Unit (GRU), the DGD-CNet model enhances the channel estimation accuracy and effectively captures both spatial structures and time correlation in time-varying channels. The results show that the proposed DGD-CNet model outperformed existing models in the literature, achieving at least a 26% improvement in Normalized Mean Square Error (NMSE), a 2% increase in correlation coefficient, and a 4% in system accuracy under Low-Compression Ratio (Low-CR) in indoor situations. Additionally, the proposed model demonstrates effectiveness across different CRs and in outdoor scenarios.

Analysis and Design of Integrated Quadrature Balanced N-Path Transceivers for Frequency Division Duplex Systems

Analysis and Design of Integrated Quadrature Balanced N-Path Transceivers for Frequency Division Duplex Systems

Two stage beamforming and combining scheme for FDD massive MIMO systems with multi‐antenna users

AbstractThis paper proposes a two‐stage beamforming and combining scheme in frequency division duplex (FDD) massive multiple‐input multiple‐output (MIMO) systems with multi‐antenna users. Specifically, the proposed scheme is a two‐stage scheme, where the pre‐beamforming matrix and pre‐combining matrix are designed using the channel covariance matrix (CCM) in the first stage. The problem of the pre‐beamforming matrix and pre‐combining matrix design are formulated as an 0–1 quadratic integer programming problem. To solve this problem, it is further transformed into an 0–1 mixed linear integer programming problem. In the second stage, the sparse code multiple access and multi‐user precoding and combining are adopted to mitigate the inter‐user interference. Different from the previous transmission scheme using CCM, the proposed scheme consider the multi‐antenna user system, and uses the CCM to design both the pre‐beamforming and pre‐combining matrices to sparsify the effective channel matrix, such that the overhead of pilot and feedback can be reduced. Moreover, the sparse code multiple access can help to better reduce the inter‐user interference. Simulation results validate the good performance of the proposed scheme.

Deep learning-based channel estimation with application to 5G and beyond networks

Channel state information (CSI) feedback estimation for a downlink medium in a massive multiple input multiple output (MIMO) system is an essential and critical task to improve channel capacity and performance yield, especially in a frequency division duplex (FDD) multiplexing system. However, spectral efficiency degradation is a massive issue due to high channel feedback overhead. This work proposes a deep learning-based channel estimation (DLCE) model to improve channel reconstruction efficiency and channel overhead reduction accuracy. The proposed deep learning (DL) mechanism consists of encoder and decoder network where encoder network is utilized to compress CSI matrices whereas decoder network is used to decompress obtained CSI matrices. Here, inverse discrete Fourier transform (IDFT) method is utilized to convert CSI matrices of frequency domain into CSI matrices of delay domain. Simulation results are evaluated between uplink and downlink medium in the massive MIMO system considering a co-operation in science and technology (COST) 2,100 model. Here, a significant improvement in correlation and normalized mean square error (NMSE) results is observed. The proposed DLCE model shows superior performance against varied channel estimation techniques in terms of NMSE and correlation efficiency.

Digital cancellation of multi-band passive inter-modulation based on Wiener-Hammerstein model

Utilizing multi-band and multi-carrier techniques enhances throughput and capacity in Long-Term Evolution (LTE)-Advanced and 5G New Radio (NR) mobile networks. However, these techniques introduce Passive Inter-Modulation (PIM) interference in Frequency-Division Duplexing (FDD) systems. In this paper, a novel multi-band Wiener-Hammerstein model is presented to digitally reconstruct PIM interference signals, thereby achieving effective PIM Cancellation (PIMC) in multi-band scenarios. In the model, transmitted signals are independently processed to simulate Inter-Modulation Distortions (IMDs) and Cross-Modulation Distortions (CMDs). Furthermore, the Finite Impulse Response (FIR) filter, basis function generation, and B-spline function are applied for precise PIM product estimation and generation in multi-band scenarios. Simulations involving 4 carrier components from diverse NR frequency bands at varying transmitting powers validate the feasibility of the model for multi-band PIMC, achieving up to 19 dB in PIMC performance. Compared to other models, this approach offers superior PIMC performance, exceeding them by more than 5 dB in high transmitting power scenarios. Additionally, its lower sampling rate requirement reduces the hardware complexity associated with implementing multi-band PIMC.

A Quadrature Balanced N-Path Receiver for Frequency Division Duplex With Thermal and Phase Noise Cancellation Under Antenna VSWR

A Quadrature Balanced <i>N</i>-Path Receiver for Frequency Division Duplex With Thermal and Phase Noise Cancellation Under Antenna VSWR

A broadband diplexer-integrated double-pole single-throw switch for FDD/TDD operations

ABSTRACT A broadband diplexer-integrated double-pole single-throw (DPST) switch is proposed to realize frequency division duplexing (FDD) and time division duplexing (TDD). It consists of a lowpass filter (LPF) and a bandpass filter (BPF). The series LC resonators are used in both channels to create transmission zeros (TZs) in the stopband to ensure high selectivity. The diplexer is realized by inter-digital capacitors and microstrip section inductors, which can achieve low cost and compact size. Besides, this diplexer does not require a T-junction, achieving a compact size. For demonstration, a diplexer operating in DC-1.78/3.29–4.42 GHz has been designed, fabricated, and measured. The diplexer has four operating modes. And it has a compact size of 24.67 mm × 21.4 mm. The measured results show that the diplexer exhibits broadband, low insertion losses, high isolation, and high selectivity.

Maximizing the Downlink Data Rates in Massive Multiple Input Multiple Output with Frequency Division Duplex Transmission Mode Using Power Allocation Optimization Method with Limited Coherence Time

The expected development of the future generation of wireless communications systems such as 6G aims to achieve an ultrareliable and low-latency communications (URLLCs) while maximizing the data rates. These requirements push research into developing new advanced technologies. To this end, massive multiple input multiple output (MMIMO) is introduced as a promising transmission approach to fulfill these requirements. However, maximizing the downlink-achievable sum rate (DASR) in MMIMO with a frequency division duplex (FDD) transmission mode and limited coherence time (LCT) is very challenging. To address this challenge, this paper proposes a DASR maximization approach using a feasible power allocation optimization method. The proposed approach is based on smartly allocating the total transmit power between the data transmission and training sequence transmission for channel estimation. This can be achieved by allocating more energy to the training signal than the data transmission during the channel estimation process to improve the quality of channel estimation without compromising more training sequence length, thus maximizing the DASR. Additionally, the theory of random matrix approach is exploited to derive an asymptotic closed-form expression for the DASR with a regularized zero-forcing precoder (RZFP), which allows the power optimization process to be achieved without the need for computationally complex Monte Carlo simulations. The results provided in this paper indicate that a considerable enhancement in the DASR performance is achieved using the proposed power allocation method in comparison with the conventional uniform power allocation method.

A Full-Duplex 60 GHz Transceiver with Digital Self-Interference Cancellation

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60 GHz wireless communication systems. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operations to deliver better channel utilization and faster response times for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operations has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12 GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2 kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60 GHz system, a wide-bandwidth baseband digital variable-gain amplifier (DVGA) with a 3 dB bandwidth of more than 4 GHz also supports frequency division duplex (FDD) operations. The transceiver chip is fabricated using the Tower Jazz 0.18 µm SiGe BiCMOS process. With an on-board antenna, the transceiver covers all four channels in the 802.11ad standard, with MCS-12 (7.04 Gbps under 1.76 GSym/s and 16-QAM) under 1.5 m. In the proposed system design, the RF frontend-based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54 dB. To achieve a practical FD application, the SI is further suppressed with the help of a digital SI compensation. The measured power consumption for the transmitter and receiver configurations are 194 mW and 231 mW, respectively, in HD mode and 398 mW for the FDD or FD operation mode.

ACTIVE TRANSMITTER SIGNAL CANCELLATION IN RECEIVE SIGNAL PATH FOR SDR

Elimination of receiver (RX) band-pass filters is actual task for construction of next generation New Radio Wireless Transceivers and other modern equipment (Multiple Input Multiple Output systems, radar applications, etc.) based on software-defined radio. Unfortunately, some new problems with electromagnetic compatibility arise. Main problem start up with Frequency Division Duplex mode, were part of high power transmitter (TX) signal came to high sensitivity RX input through duplexer with limited isolation. In presence of high TX signal RX mixer could come into non-linear working area and RX sensitivity is decreases. This problem may be solved by cancellation of TX signal from RX path. This article provides a preliminary approach to the problem of active TX signal cancellation in RX signal path with cancellation is at least 25 dB, and relatively small additional power consumption and noise. After critical parameters identifying, based on mathematical expressions, the requirements for cancellation blocks parameters are determined. Simplest implementations of the proposed structure are simulated.

Adaptive refined random orthogonal matching pursuit algorithm for FBMC/OQAM MIMO framework

The fifth generation of wireless communication is anticipated to provide improved quality of service and enhanced data rates to the end users. One such technology that stands out as a potential transmission scheme for 5G systems is Filter Bank Multicarrier using Offset Quadrature Amplitude Modulation (FBMC/OQAM) with an effective channel estimation technique for improved performance. However, due to the inherent imaginary interference, channel estimation methods relying on preamble structures in FBMC/OQAM systems exhibit sub-optimal performance, particularly within Multiple-Input Multiple-Output (MIMO) setups. For channel estimation schemes based on compressed sensing, the inherent sparsity of wireless channels can be exploited for accurate channel reconstruction and overall performance improvement.We propose a novel compressed sensing based algorithm namely, Adaptive Refined Random Orthogonal Matching Pursuit (ARROMP), for MIMO-FBMC system with Coordinated MultiPoint (CoMP) scheduling. This algorithm adaptively selects a support set by utilizing a double threshold for the minimization of mean squared error and for accurate channel reconstruction. The proposed algorithm's performance is compared with existing Orthogonal Matching Pursuit (OMP) schemes such as random OMP, refined random OMP, and least square-based estimation. The numerical simulations suggest that the proposed adaptive algorithm provides performance improvement in terms of reduced Mean Squared Error (MSE) of channel reconstruction and Bit Error Rate (BER). Moreover, the proposed ARROMP algorithm for MIMO-FBMC is rigorously tested with CoMP scheduling for a cellular network using frequency division duplex mode. The proposed system presents significant improvements in throughput and spectral efficiency for all types of cell users, including cell-edge users. The simulation results validate the improved performance of the proposed algorithm with CoMP scheduling over the existing single-cell system with no coordination.

Performance analysis and optimization of frequency division duplex based virtual full-duplex communication systems

Virtual full-duplex (VFD) communication systems have become smart alternative over residual self-interference (RSI) affected full-duplex (FD) systems and thus has drawn significant research attention in the recent years. However, in comparison to FD, the VFD system models studied in the literature are based on successive relaying (SR) that require an extra time phase and a double number of relays for each destination user. Thus, we propose a novel frequency division duplex (FDD) based VFD (FDD-VFD) system model that can not only match FD in terms of resource utilization but also outperform both SR-VFD and FD. We consider two practical scenarios of absence of inter relay interference (A-IRI) and presence of IRI (P-IRI). We analyze the outage probability and ergodic rate performance metrics and present their analytical expressions in closed-form over Nakagami-m fading channels. Next, to minimize the effect of inter-relay interference in P-IRI scenario, we investigate optimization problems of minimizing the system outage probability and maximizing the ergodic sum rate for jointly allocating transmit power of the relays. We utilize particle swarm optimization algorithm and deep learning architecture to solve the formulated problems. Extensive evaluations are carried out over different system parameters to prove the efficacy of proposed FDD scheme and obtain key inferences.

Implementation of SIC Algorithms in the 5G DL

In this paper, we have implemented successive interference cancellation algorithms in the 5G downlink. We have calculated the maximum throughput in Frequency Division Duplex (FDD) mode in the downlink, where we have obtained a value equal to 836932 b/ms. The transmitter is of type Multiple Input Multiple Output (MIMO) with eight transmitting and receiving antennas. Each antenna among eight transmits simultaneously a data rate of 104616 b/ms that contains the binary messages of the three users. In this case, the cyclic redundancy check CRC is negligible, the Block error rate BLER is null, the MIMO category is the spatial diversity. The technology used for this is called Non-Orthogonal Multiple Access (NOMA) with a Quadrature Phase Shift Keying (QPSK) modulation. The transmission is done in a Rayleigh fading channel with the presence of obstacles. The MIMO Successive Interference Cancellation (SIC) receiver with two transmitting and receiving antennas recovers its binary message without errors for certain values of transmission power such as 50 dBm, with 0.054485% errors when the transmitted power is 20 dBm and with 0.00286763% errors for a transmitted power of 32 dBm(in the case of user 1) as well as with 0.0114705% errors when the transmitted power is 20 dBm also with 0.00286763% errors for a power of 24 dBm(in the case of user2) by applying the steps involved in SIC.

Design and analysis of quantized feedback based user-antenna joint scheduling scheme for ongoing 5G and beyond multi-user massive MIMO FDD communication systems

For the efficient user scheduling (US) and interference mitigation, channel state information (CSI) is mandatory at the base station (BS), particularly for the frequency division duplexing (FDD) systems where the users need to provide some CSI back to the BS for performing the scheduling process. As the feedback overhead increases drastically with increase of antennas as well as users, so, US with limited/reduced feedback is essential. Deploying massive multiple-input multiple-output frequency division duplexing (mMIMO FDD) systems remains an open area for research with major difficulties of associated uplink CSI feedback load as the downlink and uplink channels are not reciprocal. Therefore, smart balancing is required between feedback data and achievable throughput while scheduling the users. In order to handle the above mentioned issue, we employed a selective 4-bit quantized CSI feedback based user-antenna paired/joint scheduling scheme for the multi user (MU) FDD mMIMO systems. The key idea involves in this process is that, only a limited set of users qualifying a predefined selection threshold feed back the 4-bit quantized signal-to-interference-plus-noise ratio (SINR) values based on angle-of-departure (AoD) along with the antenna indices for the scheduling process. The BS schedules the users with respective best antenna. Furthermore, using this scheme the multi user diversity gain is also achieved. This dynamic adjustment of antenna/user selection and collision free antenna sharing between the users majorly helps in improving the throughput of the system with this selective 4-bit quantized limited feedback. The mathematical sum rate performance analysis has been demonstrated along with simulation results for different system parameters.

Modular CSI Quantization for FDD Massive MIMO Communication

We consider high-dimensional MIMO transmissions in frequency division duplexing (FDD) systems. For precoding, the frequency selective channel has to be measured, quantized and fed back to the base station by the users. When the number of antennas is very high this typically leads to prohibitively high quantization complexity and large feedback. In 5G New Radio (NR), a modular quantization approach has been applied for this, where first a low-dimensional subspace is identified for the whole frequency selective channel, and then subband channels are linearly mapped to this subspace and quantized. We analyze how the components in such a modular scheme contribute to the overall quantization distortion. Based on this analysis we improve the technology components in the modular approach and propose an orthonormalized wideband precoding scheme and a sequential wideband precoding approach which provide considerable gains over the conventional method. We compare the performance of the developed quantization schemes to prior art by simulations in terms of the projection distortion, overall distortion and spectral efficiency, in a scenario with a realistic spatial channel model.

Performance Analysis of DoA Estimation for FDD Cell Free Systems Based on Compressive Sensing Technique

The concept of cell free (CF) massive MIMO systems is a prospective fifth generation communication technology that effort with base stations for the privilege of user-centric coverage. Most studies on the CF massive MIMO system in the past imply that systems that use time division duplexing (TDD), even despite the systems using frequency division duplex (FDD) predominate in today’s wireless communications. When the number of antennas increases in FDD systems, channel state information (CSI) collection and feedback overhead become major issues. In order to mitigate these issues, we make use of the condition that the so-called uplink and downlink multipath components are comparable. Base station takes use of the angle reciprocity may immediately obtain information on channel parameters from the uplink training signal. In this paper, for CF massive MIMO system based on FDD, we provide compressive sensing (CS) of directions of arrival (DoAs) estimation approach of access point cooperation based on the channel parameters. The suggested estimation approach outperforms the established subspace-based technique, according to simulation findings. Additionally, we showed that the results of our compressive sensing estimator against the conventional estimation method. The former demonstrates way far better outcome and performance accordingly than the latter.

CSI Feedback Model Based on Multi-Source Characterization in FDD Systems.

In wireless communication, to fully utilize the spectrum and energy efficiency of the system, it is necessary to obtain the channel state information (CSI) of the link. However, in Frequency Division Duplexing (FDD) systems, CSI feedback wastes part of the spectrum resources. In order to save spectrum resources, the CSI needs to be compressed. However, many current deep-learning algorithms have complex structures and a large number of model parameters. When the computational and storage resources are limited, the large number of model parameters will decrease the accuracy of CSI feedback, which cannot meet the application requirements. In this paper, we propose a neural network-based CSI feedback model, Mix_Multi_TransNet, which considers both the spatial characteristics and temporal sequence of the channel, aiming to provide higher feedback accuracy while reducing the number of model parameters. Through experiments, it is found that Mix_Multi_TransNet achieves higher accuracy than the traditional CSI feedback network in both indoor and outdoor scenes. In the indoor scene, the NMSE gains of Mix_Multi_TransNet are 4.06 dB, 4.92 dB, 4.82 dB, and 6.47 dB for compression ratio η = 1/8, 1/16, 1/32, 1/64, respectively. In the outdoor scene, the NMSE gains of Mix_Multi_TransNet are 3.63 dB, 6.24 dB, 4.71 dB, 4.60 dB, and 2.93 dB for compression ratio η = 1/4, 1/8, 1/16, 1/32, 1/64, respectively.

Amplitude prediction from uplink to downlink CSI against receiver distortion in FDD systems

In frequency division duplex (FDD) massive multiple-input multiple-output (mMIMO) systems, the reciprocity mismatch caused by receiver distortion seriously degrades the amplitude prediction performance of channel state information (CSI). To tackle this issue, from the perspective of distortion suppression and reciprocity calibration, a lightweight neural network-based amplitude prediction method is proposed in this paper. Specifically, with the receiver distortion at the base station (BS), conventional methods are employed to extract the amplitude feature of uplink CSI. Then, learning along the direction of the uplink wireless propagation channel, a dedicated and lightweight distortion-learning network (Dist-LeaNet) is designed to restrain the receiver distortion and calibrate the amplitude reciprocity between the uplink and downlink CSI. Subsequently, by cascading, a single hidden layer-based amplitude-prediction network (Amp-PreNet) is developed to accomplish amplitude prediction of downlink CSI based on the strong amplitude reciprocity. Simulation results show that, considering the receiver distortion in FDD systems, the proposed scheme effectively improves the amplitude prediction accuracy of downlink CSI while reducing the transmission and processing delay.

RIS-Assisted Self-Interference Mitigation for In-Band Full-Duplex Transceivers

The wireless in-band full-duplex (IBFD) technology can in theory double the system capacity over the conventional frequency division duplex (FDD) or time-division duplex (TDD) alternatives. But the strong self-interference of the IBFD can cause excessive quantization noise at the output of the analog-to-digital converters (ADCs), which hampers its real implementation. Fortunately, the reconfigurable intelligent surface (RIS) can reconfigure the wireless channels by dynamically adjusting the reflection coefficients, which makes it a promising solution to self-interference mitigation (SIM) for the IBFD system. This paper considers a RIS-assisted IBFD (RAIBFD) system where a full-duplex base station (BS), assisted by a co-located RIS, receives and transmits signals on the same frequency band simultaneously. We propose to jointly design the DL precoding matrix and the RIS coefficients to mitigate the strong self-interference before the ADCs of finite bit resolutions. To gauge the performance of the proposed RAIBFD system, we also consider an idealistic RIS-assisted IBFD (I-RAIBFD) system with ADCs of infinite bit resolutions and RIS-assisted FDD (RAFDD) system, and take them as performance benchmarks. The effectiveness of the proposed RAIBFD system is verified by simulation studies, even if the phases of the RIS have only finite resolutions.

On Scalability of FDD-Based Cell-Free Massive MIMO Framework.

Cell-free massive multiple-input multiple-output (MIMO) systems have the potential of providing joint services, including joint initial access, efficient clustering of access points (APs), and pilot allocation to user equipment (UEs) over large coverage areas with reduced interference. In cell-free massive MIMO, a large coverage area corresponds to the provision and maintenance of the scalable quality of service requirements for an infinitely large number of UEs. The research in cell-free massive MIMO is mostly focused on time division duplex mode due to the availability of channel reciprocity which aids in avoiding feedback overhead. However, the frequency division duplex (FDD) protocol still dominates the current wireless standards, and the provision of angle reciprocity aids in reducing this overhead. The challenge of providing a scalable cell-free massive MIMO system in an FDD setting is also prevalent, since computational complexity regarding signal processing tasks, such as channel estimation, precoding/combining, and power allocation, becomes prohibitively high with an increase in the number of UEs. In this work, we consider an FDD-based scalable cell-free network with angular reciprocity and a dynamic cooperation clustering approach. We have proposed scalability for our FDD cell-free and performed a comparative analysis with reference to channel estimation, power allocation, and precoding/combining techniques. We present expressions for scalable spectral efficiency, angle-based precoding/combining schemes and provide a comparison of overhead between conventional and scalable angle-based estimation as well as combining schemes. Simulations confirm that the proposed scalable cell-free network based on an FDD scheme outperforms the conventional matched filtering scheme based on scalable precoding/combining schemes. The angle-based LP-MMSE in the FDD cell-free network provides 14.3% improvement in spectral efficiency and 11.11% improvement in energy efficiency compared to the scalable MF scheme.