Free-standing Bilayer Research Articles

Fabrication of 60μm-Thick Free-Standing Bilayer Solid Electrolytes for Solid-State Batteries Using Solution Processing and Lamination

Development of solid-state batteries with a high voltage cathode and lithium metal anode could enable high energy density while avoiding safety issues of flammable liquid electrolytes. However, the solid electrolyte (SE) should meet multiple requirements, including 1) electrochemical stability at both the cathode and anode side interfaces, 2) small thickness (tens of μm) to maximize energy density of the cell, and 3) fabrication with a scalable manufacturing method. Using bilayer SEs with different electrochemical stability windows could enable stability at both cathode|SE and anode|SE interfaces. In this work, we developed a manufacturing process to fabricate thin (60 μm) free-standing bilayer SE films from slurry casting and lamination, which can be used for large scale manufacturing of SSBs.Halide SE (Li3InCl6) and sulfide SE (Li6PS5Cl) were slurry casted on different substrates, and then were dried in vacuum before being laminated onto each other to make a free-standing bilayer film. The parallel slurry casting approach eliminates cross-compatibility requirements of the solvents used for slurry preparation. The resulting bilayer films after densification were pin-hole free without intermixing between the two phases. The ionic conductivity of the bilayer SE film was ~70% of the bilayer SE pellet (1 mm thickness in total) made with a conventional powder pressing method. However, because the thickness of bilayer SE film (60 μm) was much smaller than the bilayer SE pellet (1 mm), the bilayer SE film had ~10x lower area-specific resistance (ASR) compared to the bilayer SE pellet. Because of the lower total cell resistance, the cell made with the bilayer SE film had a better rate capability compared to the reference cell in pellet geometry.The strategy developed in this work could be integrated into current manufacturing infrastructure of battery fabrication as it is based on slurry casting, which is already a well-established fabrication method for lithium-ion batteries. Moreover, it could be used to fabricate multi-layered solid-state architectures in general, which are challenging to manufacture due to solvent compatibility issues during slurry casting. The study will assist the progress of solid-state battery manufacturing by providing a scalable manufacture method to prepare thin free-standing bilayer SEs.

Freestanding bilayer microscope for single-molecule imaging of membrane proteins.

Integral membrane proteins (IMPs) constitute a large fraction of organismal proteomes, playing fundamental roles in physiology and disease. Despite their importance, the mechanisms underlying dynamic features of IMPs, such as anomalous diffusion, protein-protein interactions, and protein clustering, remain largely unknown due to the high complexity of cell membrane environments. Available methods for in vitro studies are insufficient to study IMP dynamics systematically. This publication introduces the freestanding bilayer microscope (FBM), which combines the advantages of freestanding bilayers with single-particle tracking. The FBM, based on planar lipid bilayers, enables the study of IMP dynamics with single-molecule resolution and unconstrained diffusion. This paper benchmarks the FBM against total internal reflection fluorescence imaging on supported bilayers and is used here to estimate ion channel open probability and to examine the diffusion behavior of an ion channel in phase-separated bilayers. The FBM emerges as a powerful tool to examine membrane protein/lipid organization and dynamics to understand cell membrane processes.

Restoring the electronic properties of epitaxial graphene on SiC substrate by Ar intercalation

Thermal decomposition of 6H–SiC(0001) under an argon atmosphere is a promising technique to fabricate large-scale epitaxial graphene monolayers for electronic applications. In this manuscript, we report on the intercalation of argon, hydrogen and oxygen atoms underneath a graphene buffer layer (BL) on SiC(0001), involving bond formation between the intercalated agent and Si atoms. Density Functional Theory calculations were performed to investigate the atomic structure, stability and electronic properties of quasi free-standing monolayer graphene and bilayer graphene, accomplished by intercalation. According to our results, as the Ar intercalated atoms saturate the silicon dangling bonds in the upper SiC surface, the BL is completely detached from the substrate and transformed into free-standing graphene. Ar intercalation would be hindered by the concurrent and thermodynamically more spontaneous adsorption of Ar atop the graphene layers, resulting in a pronounced decrease of the process efficiency. High Ar-coverage regimes and low kinetic barriers for Ar intercalation might shift the intercalation/adsorption balance. These factors as well as strategies such as ion implantation could be explored to identify more favorable conditions to experimentally test Ar intercalation as a simple method to achieve control of the electronic properties of the BL and help preserve the unique characteristics of graphene.

Smart Free-Standing Bilayer Polyacrylamide/DNA Hybrid Hydrogel Film-Based Sensing System Using Changes in Bending Angles as a Visual Signal Readout.

Stimuli-responsive DNA hydrogels have shown great potential in sensing applications due to their attractive properties such as programmable target responsiveness, excellent biocompatibility, and biodegradability. In contrast to the extensively developed DNA hydrogel sensing systems based on the stimuli-responsive hydrogel-to-solution phase transition of the hydrogel matrix, the quantitative sensing application of DNA hydrogels exhibiting smart shape deformations has rarely been explored. Moreover, bulk DNA hydrogel-based sensing systems also suffer from high material cost and slow response. Herein, free-standing bilayer polyacrylamide/DNA hybrid hydrogel films with programmable responsive properties directed by the sequence of functional DNA units have been constructed. Compared with bulk DNA hydrogels, these DNA hydrogel films with a thickness at the micrometer scale not only greatly reduce the consumption of DNA materials but also facilitate the mass transfer of biomacromolecular substances within the hydrogel network, thus favoring their sensing applications. Therefore, a target-responsive smart DNA hydrogel film-based sensor system is further demonstrated based on the large amplitude macroscopic shape deformation of the film as a visual signal readout. As a proof of concept, Pb2+ or UO22+ ion-responsive DNA units were introduced into the active layer of the bilayer hydrogel films. In the presence of Pb2+ or UO22+ ions, the occurrence of a cleavage reaction within the DNA units leads to the release of DNA segments from the hydrogel film, inducing a dramatic shape deformation of the film, and thus sensing of Pb2+ or UO22+ ions with high specificity is achieved based on measuring the bending angle changes of these smart free-standing films. These smart DNA hydrogel film sensors with target-programmable responsiveness, simple operation, and ease of storage may hold promise for future rapid on-site testing applications.

On-surface chemical dynamics of monolayer, bilayer, and many-layered graphene surfaces probed with supersonic beam scattering and STM imaging.

We have developed the capability to elucidate interfacial reaction dynamics using an arguably unique combination of supersonic molecular beams combined with in situ STM visualization. These capabilities have been implemented in order to reveal the complex spatiotemporal correlations that govern the oxidation of graphitic systems spanning atomic-, nano-, and meso-length scales. In this study, the 3 nm periodic moiré pattern of monolayer and bilayer graphene on Ru(0001) provides a diverse palette of potential scattering and binding sites at the interface for ground state atomic oxygen. We resolve the site-specificity of atomic oxygen placement on the moiré lattice for both monolayer and bilayer graphene on Ru(0001) with atomic resolution. Angle- and energy-controlled scattering of O(3P) on these interfaces reveals an incisive side-by-side comparison of preferential reactivity of the monolayer surface compared to a more free-standing bilayer graphene ruthenium interface. Morphologically dependent reactivity of many layered graphene (HOPG) and monolayer graphene on Ru(0001) reveal anisotropic on-surface reactivity dependent on the presence of proximal reacted sites or local regions. The kinetics of on-surface oxidation are additionally shown to influence the morphology of surface products by varying the temperature of the interface and flux of reactant species. Such correlations are important in chemisorption, catalysis, materials oxidation and erosion, and film processing-and tunable moiré templated adsorption is a route to well-ordered self-assembled 2D materials for use in next-generation platforms for quantum devices and catalysis. Taken together, these results highlight a new direction in the examination of interfacial reaction dynamics where incident beam kinetic energy and angle of incidence can be used as reaction control parameters, with outcomes such as site-specific reactivity, changes for overall time-evolving mechanisms, and the relative importance of non-adiabatic channels in adsorption all linked to the on-surface fate of chemisorbed species.

Breath-like interlayer bonding facilitates efficient metal-ion storage in bilayer borophene with decreased adherence capabilities on Ag substrate

The fabrication of bilayer borophene presents an alternative approach to tackle the challenges related to thermodynamic stability and the detachment of monolayer borophene from the metal substrate, which currently restrict its practical application. However, recent theoretical investigations have revealed that the structural arrangement of the most energetic free-standing bilayer borophene, denoted as BL-α+ borophene, is different from the configuration observed experimentally (Nat. Mater. 2022, 21, 35–40). Herein, the effects of introducing an additional stratum of borophene on the electronic properties, mechanical performance, adherence capabilities towards Ag (111), and electrochemical performance as an anode material for alkali-ions batteries has been thoroughly examined. The results demonstrate that free-standing BL-α+ borophene manifests a reduced energy adhesion (Eadh) of −0.059 eV Å−2 when contrasted with its monolayer counterpart. Furthermore, the interlayer B-B bonding exhibits a breath-like dilatation and contraction behavior during metal-ion adsorption/desorption, leading to remarkable theoretical capacities of 1351.6 mAh/g for Li-ion anodes, 1351.6 mAh/g for Na-ion anodes, and 450.53 mAh/g for K-ion anodes, accompanied by moderate diffusion barriers of 0.58 eV, 0.34 eV, and 0.23 eV for Li, Na, and K ions, respectively. These results provide valuable insights into the application of borophene-based electrode materials that exhibit improved stability through a “self-stacking” mechanism.

Bending stiffness collapse, buckling, topological bands of freestanding twisted bilayer graphene

Bending stiffness collapse, buckling, topological bands of freestanding twisted bilayer graphene

An Efficient Ambient-Moisture-Driven Wearable Electrical Power Generator.

Existing devices for generating electrical power from water vapor in ambient air require high levels of relative humidity (RH), cannot operate for prolonged periods, and provide insufficient output for most practical applications. Here a heterogeneous moisture-driven electrical power generator (MODEG) is developed in the form of a free-standing bilayer of polyelectrolyte films, one consisting of a hygroscopic matrix of graphene oxide(GO)/polyaniline(PANI) [(GO)PANI] and the other consisting of poly(diallyldimethylammonium chloride)(PDDA)-modified fluorinated Nafion (F-Nafion (PDDA)). One MODEG unit (1 cm2 ) can deliver a stable open-circuit output of 0.9V at 8µA for more than 10h with a matching external load. The device works over a wide range of temperature (-20 to +50 °C) and relative humidity (30% to 95% RH). It is shown that series and parallel combinations of MODEG units can directly supply sufficient power to drive commercial electronic devices such as light bulbs, supercapacitors, circuit boards, and screen displays. The (GO)PANI:F-Nafion (PDDA) hybrid film is embedded in a mask to harvest the energy from exhaled water vapor in human breath under real-life conditions. The device could consistently generate 450-600mV during usual breathing, and provides sufficient power to drive medical devices, wearables, and emergency communication.

Freestanding region-responsive bilayer for functional packaging of ingestible devices

Ingestible capsules have the potential to become an attractive alternative to traditional means of treating and detecting gastrointestinal (GI) disease. As device complexity increases, so too does the demand for more effective capsule packaging technologies to elegantly target specific GI locations. While pH-responsive coatings have been traditionally used for the passive targeting of specific GI regions, their application is limited due to the geometric restrictions imposed by standard coating methods. Dip, pan, and spray coating methods only enable the protection of microscale unsupported openings against the harsh GI environment. However, some emerging technologies have millimeter-scale components for performing functions such as sensing and drug delivery. To this end, we present the freestanding region-responsive bilayer (FRRB), a packaging technology for ingestible capsules that can be readily applied for various functional ingestible capsule components. The bilayer is composed of rigid polyethylene glycol (PEG) under a flexible pH-responsive Eudragit® FL 30 D 55, which protects the contents of the capsule until it arrives in the targeted intestinal environment. The FRRB can be fabricated in a multitude of shapes that facilitate various functional packaging mechanisms, some of which are demonstrated here. In this paper, we characterize and validate the use of this technology in a simulated intestinal environment, confirming that the FRRB can be tuned for small intestinal release. We also show a case example where the FRRB is used to protect and expose a thermomechanical actuator for targeted drug delivery.

Structural identification of graphene films and nanoislands on 6H-SiC(0001) by direct height measurement

By combining non-contact atomic force microscopy (nc-AFM) and Kelvin probe microscopy (KPFM) in ultra high vacuum environment (UHV), we directly measure the height and work function of graphene monolayer on the Si-face of 6H-SiC(0001) with a precision that allows us to differentiate three different types of graphene structures : zero layer graphene (ZLG), Quasi free-standing monolayer graphene (QFMLG) and bilayer graphene (BLG). The height and work function of ZLG are 2.62 ± 0.22 Å and 4.42 ± 0.05 eV respectively, when they are 4.09 ± 0.11 Å and 4.63 ± 0.05 eV for QFMLG. The work function is 4.83 ± 0.05 eV for the BLG. Unlike any other available technique, the local nc-AFM/KPFM dual probe makes it possible to directly identify the nature of nanometer-sized graphene islands that constitute the early nuclei of graphene monolayer grown on 6H-SiC(0001) by chemical vapor deposition.

Determining the Bending Rigidity of Free-Standing Planar Phospholipid Bilayers

We describe a method to determine membrane bending rigidity from capacitance measurements on large area, free-standing, planar, biomembranes. The bending rigidity of lipid membranes is an important biological mechanical property that is commonly optically measured in vesicles, but difficult to quantify in a planar, unsupported system. To accomplish this, we simultaneously image and apply an electric potential to free-standing, millimeter area, planar lipid bilayers composed of DOPC and DOPG phospholipids to measure the membrane Young's (elasticity) modulus. The bilayer is then modeled as two adjacent thin elastic films to calculate bending rigidity from the electromechanical response of the membrane to the applied field. Using DOPC, we show that bending rigidities determined by this approach are in good agreement with the existing work using neutron spin echo on vesicles, atomic force spectroscopy on supported lipid bilayers, and micropipette aspiration of giant unilamellar vesicles. We study the effect of asymmetric calcium concentration on symmetric DOPC and DOPG membranes and quantify the resulting changes in bending rigidity. This platform offers the ability to create planar bilayers of controlled lipid composition and aqueous ionic environment, with the ability to asymmetrically alter both. We aim to leverage this high degree of compositional and environmental control, along with the capacity to measure physical properties, in the study of various biological processes in the future.

Ultrafast hot-carrier cooling in quasi freestanding bilayer graphene with hydrogen intercalated atoms.

Femtosecond-THz optical pump probe spectroscopy is employed to investigate the cooling dynamics of hot carriers in quasi-free standing bilayer epitaxial graphene with hydrogen interacalation. We observe longer decay time constants, in the range of 2.6 to 6.4 ps, compared to previous studies on monolayer graphene, which increase nonlinearly with excitation intensity. The increased relaxation times are due to the decoupling of the graphene layer from the SiC substrate after hydrogen intercalation which increases the distance between graphene and substrate. Furthermore, our measurements show that the supercollision mechanism is not related to the cooling process of the hot carriers, which is ultimately achieved by electron optical phonon scattering.

Size and Shape Exclusion in 2D Silicon Dioxide Membranes

2D membranes such as artificially perforated graphene are deemed to bring great advantages for molecular separation. However, there is a lack of structure-property correlations in graphene membranes as neither the atomic configurations nor the number of introduced sub-nanometer defects are known precisely. Recently, bilayer silica has emerged as an inherent 2D membrane with an unprecedentedly high areal density of well-defined pores. Mass transfer experiments with free-standing SiO2 bilayers demonstrated a strong preference for condensable fluids over inert species, and the measured membrane selectivity revealed a key role of intermolecular forces in ångstrom-scale openings. In this study, vapor permeation measurements are combined with quantitative adsorption experiments and density functional theory (DFT) calculations to get insights into the mechanism of surface-mediated transport in vitreous 2D silicon dioxide. The membranes are shown to exhibit molecular sieving performance when exposed to vaporous methanol, ethanol, isopropanol, and tert-butanol. The results are normalized to the coverage of physisorbed molecules and agree well with the calculated energy barriers.

Axial-Bonding-Driven Dimensionality Effect on the Charge-Density Wave in NbSe2.

2H-NbSe2 is a prototypical charge-density-wave (CDW) system, exhibiting such a symmetry-breaking quantum ground state in its bulk and down to a single-atomic-layer limit. However, how this state depends on dimensionality and what governs the dimensionality effect remain controversial. Here, we experimentally demonstrate a robust 3 × 3 CDW phase in both freestanding and substrate-supported bilayer NbSe2, far above the bulk transition temperature. We exclude environmental effects and reveal a strong temperature and thickness dependence of Raman intensity from an axially vibrating A1g phonon mode, involving Se ions. Using first-principles calculations, we show that these result from a delicate but profound competition between the intra- and interlayer bonding formed between Se-pz orbitals. Our results suggest the crucial role of Se out-of-plane displacement in driving the CDW distortion, revealing the Se-dominated dimensionality effect and establishing a new perspective on the chemical bonding and mechanical stability in layered CDW materials.

Resonant phonon-magnon interactions in freestanding metal-ferromagnet multilayer structures

We analyze resonant magneto-elastic interactions between standing perpendicular spin wave modes (exchange magnons) and longitudinal acoustic phonon modes in free-standing hybrid metal-ferromagnet bilayer and trilayer structures. Whereas the ferromagnetic layer acts as a magnetic cavity, all metal layers control the frequencies and eigenmodes of acoustic vibrations. The here proposed design allows for achieving and tuning the spectral and spatial modes overlap between phonons and magnons that results in their strong resonant interaction. Realistic simulations for gold-nickel multilayers show that sweeping the external magnetic field should allow for observing resonantly enhanced interactions between individual magnon and phonon modes in a broad range of frequencies spanning from tens of GHz up to several hundreds of GHz, which can be finely tuned through the multilayer design. Our results would enable the systematic study and the deep understanding of resonantly enhanced magneto-elastic coupling between individual phonon and magnon modes up to frequencies of great contemporary fundamental and applied interest.

Thermo-responsive lipophilic NIPAM-based block copolymers as stabilizers for lipid-based cubic nanoparticles

The design of drug delivery systems (DDS) for the encapsulation of therapeutic agents and the controlled release to the target site of the disease is one of the main goals of nanomedicine. Although already explored in an extensive number of studies over the years, lipid assemblies, and particularly liposomes, are still considered the most promising and interesting candidates as DDS due to their biocompatibility and structural similarity with plasma membranes. Lately, this research area has been extended to include more complex lipid assemblies, such as cubosomes. Cubosomes are an emerging structural platform for the delivery of molecules with pharmaceutical interest, such as drugs, bioactives and contrast agents. Here we report on the application of a thermo-responsive copolymer poly(N,N-dimethylacrylamide)-block-poly(N-isopropylacrylamide) (PDMA-b-PNIPAM), as a thermoresponsive stabilizer of lipid-based nanoparticles for drug-delivery. First, we assessed the affinity of PDMA-b-PNIPAM towards supported and free-standing bilayers; then, we explored the colloidal and thermoresponsive properties of cubic self-assembled DDS composed of glycerol-monooleate (GMO), where PDMA-b-PNIPAM replaces the conventional stabilizer Pluronic F127 (PEOx-PPOy-PEOx), normally used for cubosomes. We prepared dispersions of cubic lipid nanoparticles with two PDMA-b-PNIPAM block copolymers of different molar mass. The colloidal properties were then assessed and compared to those exhibited by standard lipid cubic dispersions stabilized by Pluronic F-127, combining a series of experimental techniques (Quartz Crystal Microbalance with Dissipation monitoring, Dynamic Light Scattering, Small-Angle X-rays Scattering, Cryo-Transmission Electron Microscopy). Interestingly, PDMA-b-PNIPAM stabilized cubosomes display additional benefits with respect to those stabilized by Pluronic, thanks to the combination of a “sponge “ effect for the controlled release of encapsulated molecules and an increased affinity towards lipid bilayer membranes, which is a promising feature to maximize fusion with the target-cellular site.

Phospholipid Monolayer/Graphene Interfaces: Curvature Effect on Lipid Morphology and Dynamics.

Phospholipids are an important class of lipids that are widely used as model platforms for the study of biological processes and interactions. These lipids can form stable interfaces with solid substrates, such as graphene, and these interfaces have potential applications in biosensing and targeted drug delivery. In this paper, we perform molecular dynamics simulations of graphene-supported lipid monolayers to characterize the lipid properties of such interfaces. We observed substantial differences between the supported monolayer and free-standing bilayer in terms of the lipid properties, such as the tail order parameters, density profiles, diffusion rates, and so on. Furthermore, we studied these interfaces on sinusoidally deformed graphene substrates to understand the effect of curvature on the supported lipids. Here, we observed that the nature of the substrate curvature, that is, concave or convex, can locally affect the lipid/substrate adhesion strength and induce structural and dynamic changes in the adsorbed lipid monolayer. Together, these results help characterize the properties of lipid/graphene interfaces and provide insights into the substrate curvature effect on these interfaces, which can enable the tuning of lipid properties for various sensor devices and drug delivery applications.

Strain manipulation of ferroelectric skyrmion bubbles in a freestanding PbTiO3 film: A phase field simulation

So far nanoscale topological polar structures have been mainly observed in ferroelectric superlattices, nanodots, and complex heterostructures, originating from the intricate interplay of built-in electric field, polarization, strain, and their gradient-related energies. However, solid substrates hinder the continuous strain manipulation of the ferroelectric topological textures. Recently, a breakthrough in fabricating freestanding films has demonstrated the possibility of continuous strain manipulation, but there has been little experimental or theoretical investigation of whether polar topological structures exist in freestanding films. Herein, by performing phase field simulation on ${(\mathrm{PbTi}{\mathrm{O}}_{3})}_{20}/{(\mathrm{SrTi}{\mathrm{O}}_{3})}_{10}$ freestanding bilayers, we observed the stabilized ferroelectric skyrmion bubbles in a ferroelectric layer. A thickness-dependent phase diagram indicates that the skyrmion bubbles exist when the ferroelectric layer is between eight and 30 unit cells. Meanwhile, we demonstrated that the uniaxial strain is an effective way to manipulate the skyrmion bubble in freestanding films, which not only induces consolidation and rearrangement of skyrmion bubbles, but also induces a phase transition from the topological skyrmion bubble state to a standard ${a}_{1}/{a}_{2}$ domain state. These results provide us guidance with a mechanical approach to control topological polar structures in freestanding films.

Silicon Nitride-Based Micro-Apertures Coated with Parylene for the Investigation of Pore Proteins Fused in Free-Standing Lipid Bilayers.

In this work, we present a microsystem setup for performing sensitive biological membrane translocation measurements. Thin free-standing synthetic bilayer lipid membranes (BLM) were constructed in microfabricated silicon nitride apertures (<100 µm in diameter), conformal coated with Parylene (Parylene-C or Parylene-AF4). Within these BLMs, electrophysiological measurements were conducted to monitor the behavior of different pore proteins. Two approaches to integrate pore-forming proteins into the membrane were applied: direct reconstitution and reconstitution via outer membrane vesicles (OMVs) released from Gram-negative bacteria. The advantage of utilizing OMVs is that the pore proteins remain in their native lipid and lipopolysaccharide (LPS) environment, representing a more natural state compared to the usage of fused purified pore proteins. Multiple aperture chips can be easily assembled in the 3d-printed holder to conduct parallel membrane transport investigations. Moreover, well defined microfabricated apertures are achievable with very high reproducibility. The presented microsystem allows the investigation of fast gating events (down to 1 ms), pore blocking by an antibiotic, and gating events of small pores (amplitude of approx. 3 pA).

Lipid Droplets Embedded in a Model Cell Membrane Create a Phospholipid Diffusion Barrier.

Lipid droplets (LDs) are ubiquitous, cytoplasmic fat storage organelles that originate from the endoplasmic reticulum (ER) membrane. They are composed of a core of neutral lipids surrounded by a phospholipid monolayer. Proteins embedded into this monolayer membrane adopt a monotopic topology and are crucial for regulated lipid storage and consumption. A key question is, which collective properties of protein-intrinsic and lipid-mediated features determine spatio-temporal protein partitioning between phospholipid bilayer and LD monolayer membranes. To address this question, a freestanding phospholipid bilayer with physiological lipidic composition is produced using microfluidics and micrometer-sized LDs are dispersed around the bilayer that spontaneously insert into the bilayer. Using confocal microscopy, the 3D geometry of the reconstituted LDs is determined with high spatial resolution. The micrometer-sized bilayer-embedded LDs present a characteristic lens shape that obeys predictions from equilibrium wetting theory. Fluorescence recovery after photobleaching measurements reveals the existence of a phospholipid diffusion barrier at the monolayer-bilayer interface. Coarse-grained molecular dynamics simulation reveals lipid specific density distributions along the pore rim, which may rationalize the diffusion barrier. The lipid diffusion barrier between the LD covering monolayer and the bilayer may be a key phenomenon influencing protein partitioning between the ER membrane and LDs in living cells.