Force Recording Research Articles

A split-belt instrumented treadmill with uneven terrain

The biomechanics of walking are far less understood for uneven terrain than flat or even surfaces. This is due in part to a lack of ground reaction force and moment recordings from each leg. These are often obtained with split-belt instrumented treadmills, which are currently incompatible with uneven terrain, making it difficult to perform biomechanics analyses such as inverse dynamics. Here we show how a standard split-belt instrumented treadmill (Bertec, Inc., Columbus, OH) can be modified to accommodate a variety of uneven terrains. The principal design considerations are structural clearance to allow passage of an uneven treadmill belt and fabrication of the terrain. We designed mechanical components with sufficient clearance for terrains up to 0.045 m high, and formed the terrain from uneven strips of polystyrene. Measured ground reaction forces from each leg at typical walking speeds agreed well with an intact benchmark treadmill (minimum interclass cross correlation score = 0.97). The modifications had negligible effect on the treadmill’s structural strength. The terrain produced some noise-like vibrations, but at much higher frequencies than fundamental to human locomotion. The uneven terrain treadmill can record many steps of the full complement of ground reaction forces and moments from individual legs.

Quantitative in-vitro assessment of a novel robot-assisted system for cochlear implant electrode insertion.

As an increasing number of cochlear implant candidates exhibit residual inner ear function, hearing preservation strategies during implant insertion are gaining importance. Manual implantation is known to induce traumatic force and pressure peaks. In this study, we use a validated in-vitro model to comprehensively evaluate a novel surgical tool that addresses these challenges through motorized movement of a forceps. Using lateral wall electrodes, we examined two subgroups of insertions: 30 insertions were performed manually by experienced surgeons, and another 30 insertions were conducted with a robot-assisted system under the same surgeons' supervision. We utilized a realistic, validated model of the temporal bone. This model accurately reproduces intracochlear frictional conditions and allows for the synchronous recording of forces on intracochlear structures, intracochlear pressure, and the position and deformation of the electrode array within the scala tympani. We identified a significant reduction in force variation during robot-assisted insertions compared to the conventional procedure, with average values of 12mN/s and 32mN/s, respectively. Robotic assistance was also associated with a significant reduction of strong pressure peaks and a 17dB reduction in intracochlear pressure levels. Furthermore, our study highlights that the release of the insertion tool represents a critical phase requiring surgical training. Robotic assistance demonstrated more consistent insertion speeds compared to manual techniques. Its use can significantly reduce factors associated with intracochlear trauma, highlighting its potential for improved hearing preservation. Finally, the system does not mitigate the impact of subsequent surgical steps like electrode cable routing and cochlear access sealing, pointing to areas in need of further research.

A Case-Control Split-Mouth Study of Comparison of Maximum Occlusal Forces in Endodontically Treated Teeth and Vital Counterparts.

To compare the maximum occlusal force in endodontically treated teeth and their vital contralateral counterparts and to evaluate the intraoral factors affecting them. Thirty adult participants presented with an endodontically treated tooth and its vital contralateral counterpart were recruited, with 15 males and females in each group. Maximum occlusal forces were measured using a wireless sensor network occlusal force recorder, and the mean maximum occlusal force of endodontically treated teeth was compared with that of their vital contralateral counterparts. Multiple-factor ANOVA was used to examine the association between various clinical factors and maximum occlusal force. The mean maximum occlusal force for endodontically treated teeth was significantly higher than their vital counterparts (215.44 ± 74.11N and 202.40 ± 70.67N, respectively) (P < 0.001). Among the clinical factors, the maximum occlusal forces were significantly influenced by the location of teeth (P < 0.01) and the crown root ratio (P = 0.01). Upon further analysis of endodontically treated teeth and control groups, the location of teeth was identified as a sole factor associated with maximum occlusal force, with P < 0.05. The maximum occlusal forces for endodontically treated teeth were statistically significantly higher than those of their corresponding vital contralateral teeth.

BK channels promote action potential repolarization in skeletal muscle but contribute little to myotonia

Patients with myotonia congenita suffer from slowed relaxation of muscle (myotonia), due to hyperexcitability caused by loss-of-function mutations in the ClC-1 chloride channel. A recent study suggested that block of large-conductance voltage- and Ca2+- activated K+ channels (BK) may be effective as therapy. The mechanism underlying efficacy was suggested to be lessening of the depolarizing effect of build-up of K+ in t-tubules of muscle during repetitive firing. BK channels are widely expressed in the nervous system and have been shown to play a central role in regulation of excitability, but their contribution to muscle excitability has not been determined. We performed intracellular recordings as well as force measurements in both wild type and BK−/− mouse extensor digitorum longus muscles. Action potential width was increased in BK−/− muscle due to slowing of repolarization, consistent with the possibility K+ build-up in t-tubules is lessened by block of BK channels in myotonic muscle. However, there was no difference in the severity of myotonia triggered by block of muscle Cl− channels with 9-anthracenecarboxylic acid (9AC) in wild type and BK−/− muscle fibers. Further study revealed no difference in the interspike membrane potential during repetitive firing suggesting there was no reduction in K+ build-up in t-tubules of BK−/− muscle. Force recordings following block of muscle Cl− channels demonstrated little reduction in myotonia in BK−/− muscle. In contrast, the current standard of care, mexiletine, significantly reduced myotonia. Our data suggest BK channels regulate muscle excitability, but are not an attractive target for therapy of myotonia.

A porous elastomer with a cavity array for three-dimensional plantar force sensing

Human gait is an important indicator for diagnosis of various movement-related disorders. Three-dimensional (3D) plantar force monitoring enables real-time recording of contact forces in both the normal and tangential directions in each step, providing useful clues for identification of irregular gait patterns or gait-related health issues. Most flexible sensors for gait monitoring focus on contact forces in the normal direction, being limited to detect forces in the tangential direction. Herein we have developed a porous elastomer with a cavity array (PECA) to measure 3D contact forces for gait analysis. The sensor consists of two fabric electrodes and a dielectric layer of porous Ecoflex elastomer containing a 5 × 5 cavity array, forming four parallel-plate capacitor units in a soft construction. Therefore, a 3D force in any arbitrary direction generates four unique capacitive electrical signals. Importantly, the PECA includes a well-designed combination of micrometer-scale pores and millimeter-sized cavities, dramatically improving the detection sensitivity and linear elasticity range. We have demonstrated high sensitivities of 0.41 N−1 and 0.23 N−1 in the normal and tangential directions, respectively. The flexible PECA-based sensors have been tested to sensitively distinguish various standing postures and different stride lengths for gait analysis, promising reliable translation into areas such as healthcare monitoring, sports training, and rehabilitation engineering.

Citrulline activates adenosine receptors: New insight into metabolic pathways interaction

Citrulline is a non-proteinogenic amino acid that forms as by-product in nitric oxide (NO) synthesis from arginine and may act in concert with NO as an independent signaling molecule that involves in the mechanism of vascular smooth muscle vasodilation.In this study we examined the effects of citrulline on pulmonary artery smooth muscles. Experimental design comprised outward potassium currents measurements in enzymatically isolated rat pulmonary artery smooth muscle (PASMc) cells using whole-cell patch clamp technique, isometric contractile force recordings on rat pulmonary artery rings and method of molecular docking simulation.Citrulline in a concentration 10−9-10−5 M relaxed phenylephrine (PHE)-preactivated SM of rat pulmonary artery in a dose-dependent manner (EC50 0,67 μM). This citrulline-induced relaxation was dependent on an intact endothelium. Bath application of citrulline (10-8-10-5 M) on isolated PASMc induced a significant increase in the amplitude of outward potassium current (Ik). The adenosine antagonist caffeine (10-6 M) effectively blocked both the citrulline-induced relaxation response and Ik increment. Molecular docking modeling suggests that caffeine blocking the potent activity of citrulline results from competitive interactions at the A2 adenosine receptor binding site.In summary, our data suggest that citrulline, released with NO at low concentrations, can effectively interact with adenosine receptors in smooth muscle cells, causing their relaxation, indicating surprising interaction between NO and adenosine pathways.

Transferring Sensor-Based Assessments to Clinical Practice: The Case of Muscle Synergies.

Sensor-based assessments in medical practice and rehabilitation include the measurement of physiological signals such as EEG, EMG, ECG, heart rate, and NIRS, and the recording of movement kinematics and interaction forces. Such measurements are commonly employed in clinics with the aim of assessing patients' pathologies, but so far some of them have found full exploitation mainly for research purposes. In fact, even though the data they allow to gather may shed light on physiopathology and mechanisms underlying motor recovery in rehabilitation, their practical use in the clinical environment is mainly devoted to research studies, with a very reduced impact on clinical practice. This is especially the case for muscle synergies, a well-known method for the evaluation of motor control in neuroscience based on multichannel EMG recordings. In this paper, considering neuromotor rehabilitation as one of the most important scenarios for exploiting novel methods to assess motor control, the main challenges and future perspectives for the standard clinical adoption of muscle synergy analysis are reported and critically discussed.

Compatibility of eugenol anesthesia with classroom physiology experiments on nerve and muscle of frogs

Frogs serve as valuable model organisms for studying physiological responses of nerve, skeletal muscle and the heart in undergraduate biology labs. Heretofore, induced hypothermia has been the preferred technique for pain and stress reduction prior to euthanasia by pithing. However, AVMA guidelines discourage hypothermia for restraint or euthanasia of amphibians and advocate anesthetic overdose as preferable to pithing alone. Unfortunately, the primary anesthetic used in fish and other aquatic invertebrates, MS-222, blocks normal nerve and muscle function in leopard frogs and renders them useless for classroom physiology experiments, as demonstrated by Medler (2019). Eugenol is a safe and affordable anesthetic that is effective in amphibians. We sought to test the hypothesis that eugenol anesthesia is compatible with classroom nerve and muscle experiments on frogs. Bullfrogs and leopard frogs were immersed in a bath of eugenol suspended in tap water at 275 to 350 mg/L. At various time points, a four step reflex test was performed including tests of righting response, superficial pain reflex, deep pain reflex, and corneal blink reflex. Once all reflexes were absent, the frog was euthanized by pithing and the gastrocnemius muscle was prepared for force recordings. The sciatic nerve was stimulated with a bipolar stimulating electrode while gastrocnemius force was measured using an isometric force transducer. The threshold voltage eliciting a muscle contraction and the peak isometric twitch force were recorded at 15 minute intervals for 2 hours. Control frogs were sedated by immersion in ice water for 20 to 30 minutes, pithed when reflexes were substantially weakened, and then subjected to the same stimulation protocol and force measurements. At these doses, eugenol reliably induces loss of reflexes in 20 to 35 minutes and neuromuscular preparations maintain the ability to respond to electrical stimulation. Preliminary results suggest that eugenol may produce a modest elevation of threshold voltage and a modest reduction in maximum twitch force compared to control frogs euthanized without chemical anesthesia. Eugenol may be an effective anesthetic to prepare bullfrogs and leopard frogs for classroom experiments on nerve and muscle. Funding was provided by the Bill and Linda Frost Fund. This is the full abstract presented at the American Physiology Summit 2024 meeting and is only available in HTML format. There are no additional versions or additional content available for this abstract. Physiology was not involved in the peer review process.

Indirect evidence of Bi3+ valence change and dual role of Bi3+ in trapping electrons and holes for multimode X-ray imaging, anti-counterfeiting, and non-real-time force sensing

Discovering bismuth based smart materials that can respond to thermal, mechanical, and wide range X-ray to infrared photon excitation remains a challenge. Such materials have various uses like in advanced information encryption. In this work, valence state change between Bi2+, Bi3+, and Bi4+, and the dual role of Bi3+ in trapping electrons and holes have been studied in Bi3+ or/and Ln3+ (Ln=Tb or Pr) doped LiScGeO4 family of compounds by vacuum referred binding energy (VRBE) diagram construction, thermoluminescence, and spectroscopy. Electron release from Bi2+ has been evidenced. It can be used to experimentally determine the VRBE in the Bi2+ 2P1/2 ground state and to realize Bi3+ negative quenching luminescence. Particularly, a new force induced charge carrier storage phenomenon has been discovered for non-real-time force recording. Wide range of emission tailorable afterglow, unique Bi3+ ultraviolet-A, white, and infrared afterglow have been demonstrated by using Bi3+ as a hole trapping and recombination center and using energy transfer processes from Bi3+ to Tb3+, Pr3+, Dy3+, or Cr3+. Proof-of-concept advanced anti-counterfeiting, information encryption, and X-ray imaging will be demonstrated. This work not only develops smart storage phosphors, but more importantly unravels the valence change between Bi2+, Bi3+, or Bi4+ and how it can affect the trapping and release of charge carriers with thermal, optical, or mechanical excitation. This work therefore can promote the discovery and development of Bi3+ based smart materials for various applications.

Direct recording and reading of mechanical force by afterglow evaluation of multi-piezo mechanoluminescent material Li0.12Na0.88NbO3 on well-designed morphotropic phase boundary

Mechanoluminescence (ML) refers to the photon emission from materials subjected to mechanical stimuli. A general concept concerning ML materials is that they cannot directly record a stress history (mechanical record; MR). Here, we report an approach that retrieves a quantitative recording of stress history through the afterglow characteristics analysis of a specific multi-piezo ML material Li0.12Na0.88NbO3:Pr (LNNO), which has been designated to exist near the structural phase boundary of rhombohedral R3c and orthorhombic P21ma. Contrary to the general expectation that the afterglow characteristics are irrelevant to mechanical loading history, LNNO was strongly correlated with the stress distribution after UV excitation. This enabled us to read the recorded stress precisely from the afterglow image of the material. Furthermore, the spatial distribution of the MR was also realized, showing the capability of the readout of stress history in both time and space. This unusual MR function is attributed to eliminating shallow trap sites, which affected the afterglow characteristics upon applying mechanical load.

Monitoring of Hip Joint Forces and Physical Activity after Total Hip Replacement by an Integrated Piezoelectric Element

Resultant hip joint forces can currently only be recorded in situ in a laboratory setting using instrumented total hip replacements (THRs) equipped with strain gauges. However, permanent recording is important for monitoring the structural condition of the implant, for therapeutic purposes, for self-reflection, and for research into managing the predicted increasing number of THRs worldwide. Therefore, this study aims to investigate whether a recently proposed THR with an integrated piezoelectric element represents a new possibility for the permanent recording of hip joint forces and the physical activities of the patient. Hip joint forces from nine different daily activities were obtained from the OrthoLoad database and applied to a total hip stem equipped with a piezoelectric element using a uniaxial testing machine. The forces acting on the piezoelectric element were calculated from the generated voltages. The correlation between the calculated forces on the piezoelectric element and the applied forces was investigated, and the regression equations were determined. In addition, the voltage outputs were used to predict the activity with a random forest classifier. The coefficient of determination between the applied maximum forces on the implant and the calculated maximum forces on the piezoelectric element was R2 = 0.97 (p &lt; 0.01). The maximum forces on the THR could be determined via activity-independent determinations with a deviation of 2.49 ± 13.16% and activity-dependent calculation with 0.87 ± 7.28% deviation. The activities could be correctly predicted using the classification model with 95% accuracy. Hence, piezoelectric elements integrated into a total hip stem represent a promising sensor option for the energy-autonomous detection of joint forces and physical activities.

Charge carrier trapping management in Bi3+ and lanthanides doped Li(Sc,Lu)GeO4 for x-ray imaging, anti-counterfeiting, and force recording

Discovering energy storage materials with rationally controlled trapping and de-trapping of electrons and holes upon x-rays, UV-light, or mechanical force stimulation is challenging. Such materials enable promising applications in various fields, for instance in multimode anti-counterfeiting, x-ray imaging, and non-real-time force recording. In this work, photoluminescence spectroscopy, the refined chemical shift model, and thermoluminescence studies will be combined to establish the vacuum referred binding energy (VRBE) diagrams for the LiSc1−xLuxGeO4 family of compounds containing the energy level locations of Bi2+, Bi3+, and the lanthanides. The established VRBE diagrams are used to rationally develop Bi3+ and lanthanides doped LiSc1−xLuxGeO4 storage phosphors and to understand trapping and de-trapping processes of charge carriers with various physical excitation means. The thermoluminescence intensity of x-ray irradiated LiSc0.25Lu0.75GeO4:0.001Bi3+,0.001Eu3+ is about two times higher than that of the state-of-the-art x-ray storage phosphor BaFBr(I):Eu2+. Particularly, a force induced charge carrier storage phenomenon appears in Eu3+ co-doped LiSc1−xLuxGeO4. Proof-of-concept non-real-time force recording, anti-counterfeiting, and x-ray imaging applications will be demonstrated. This work not only deepens our understanding of the capturing and de-trapping processes of electrons and holes with various physical excitation sources, but can also trigger scientists to rationally discover new storage phosphors by exploiting the VRBEs of bismuth and lanthanide levels.

Gait asymmetry in spatiotemporal and kinetic variables does not increase running-related injury risk in lower limbs: a secondary analysis of a randomised trial including 800+ recreational runners

ObjectiveTo investigate asymmetry in spatiotemporal and kinetic variables in 800+ recreational runners, identify determinants of asymmetry, investigate if asymmetry is related to greater running injury risk and compare spatiotemporal and...

Exercise pressor responses are exaggerated relative to force production during, but not following, thirty-minutes of rhythmic handgrip exercise.

This study tested the hypothesis that blood pressure responses would increase relative to force production in response to prolonged bouts of muscular work. Fifteen individuals performed two minutes of static handgrip (SHG; 35% MVC), followed by three minutes of post-exercise-cuff-occlusion (PECO), before and after thirty minutes of rest (control), or rhythmic handgrip exercise (RHG) of the contralateral and ipsilateral forearms. Beat-by-beat recordings of mean arterial pressure (MAP), heart rate (HR), and handgrip force (kg) were averaged across one-minute periods at baseline, and minutes 5, 10, 15, 20, 25, and 30 of RHG. MAP was also normalized to handgrip force, providing a relative measure of exercise pressor responses (mmHg/kg). Hemodynamic responses to SHG and PECO were also compared before and after contralateral RHG, ipsilateral RHG, and control, respectively. Similar to the RHG trial, areas under the curve were calculated for MAP (blood pressure index; BPI) and normalized to the time tension index (BPInorm). HR and MAP significantly increased during RHG (15.3 ± 1.4% and 20.4 ± 3.2%, respectively, both p < 0.01), while force output decreased by up to 36.6 ± 8.0% (p < 0.01). This resulted in a 51.6 ± 9.4% increase in BPInorm during 30min of RHG (p < 0.01). In contrast, blood pressure responses to SHG and PECO were unchanged following RHG (all p ≥ 0.07), and only the mean HR (4.2 ± 1.5%, p = 0.01) and ΔHR (67.2 ± 18.1%, p < 0.01) response to SHG were exaggerated following ipsilateral RHG. The magnitude of exercise pressor responses relative to force production progressively increases during, but not following, prolonged bouts of muscular work.

Mechanical asymmetries remain low-to-moderate during 30min of self-paced treadmill running.

Introduction: We characterized the magnitude and range of gait asymmetry during self-paced treadmill running. Methods: On an instrumented treadmill, twelve trained runners (11 males, 1 female) completed a 30-min self-paced run, during which participants were instructed to cover the most distance possible. Ground reaction force recordings at a constant velocity corresponding to 70% of their maximal aerobic velocity (13.3 ± 0.8km.h-1) allowed for the measurement of running kinetics and kinematics, as well as the calculation of spring-mass characteristics at the beginning, middle, and end of the run (minutes 1, 14, and 29, respectively). Group mean asymmetry scores were assessed using the "symmetry angle" (SA) formulae, where scores of 0% and 100% represent perfect symmetry and perfect asymmetry, respectively. Results: There was no time effect on SA scores for any of the 13 biomechanical variables (p ≥ 0.128). Mean SA scores were <2.5% for contact time (0.8% ± 0.7%), flight time (1.4% ± 0.6%), step frequency (0.7% ± 0.3%), duty factor (0.7% ± 0.3%), duration of braking (1.3% ± 0.7%) and push-off phases (0.9% ± 0.8%), as well as peak braking (2.3% ± 1.3%) and push-off forces (1.4% ± 0.9%). Mean SA scores were ≥2.5% for peak vertical loading rate (3.1% ± 1.7%), mean vertical loading rate (3.4% ± 2.1%), peak vertical forces (2.9% ± 2.2%), as well as vertical stiffness (5.2% ± 3.5%) and leg stiffness (2.5% ± 1.5%). Conclusion: Throughout a 30-min running time trial, there were consistently low-to-moderate mechanical asymmetries for spatiotemporal variables, kinetics, and spring-mass model characteristics. This suggests that trained runners maintained relatively even strides during the self-paced treadmill run, with lower extremities behaving similarly when controlling for velocity.

The Effects of Differential Learning on the Standing Broad Jump.

In this investigation, we examined the influence of two approaches of motor skill learning (differential learning and repetition-based) for an explosive motor skill. Twenty-seven individuals completed four training sessions of a standing broad jump task, presented with either differential training or a repetition-based approach. We collected pre-and post-training assessments that included maximal jump distances used to index performance and the recording of ground reaction forces to determine potential biomechanical changes (normalized vertical ground reaction force - GRFvert, rate of force development - RFD, and horizontal take-off velocity - Vhor). Results showed that differential training exhibited greater jump distances than repetition-based training (p < .001) but no training effect was found for jump distances between pre- and post-assessments for either training approach (p = .15). However, a significant increase occurred for Vhor with greater velocities achieved following training (p = .03). Overall, differential training failed to show the expected performance enhancements for a discrete, explosive motor task; this may be related to limited exposure and task specific demands of the movement. Further research is needed to better understand the task factors influencing skill acquisition from differential training.

Functional and Transcriptomic Characterization of Postnatal Maturation of ENS and SIP Syncytium in Mice Colon.

The interplay of the enteric nervous system (ENS) and SIP syncytium (smooth muscle cells-interstitial cells of Cajal-PDGFRα+ cells) plays an important role in the regulation of gastrointestinal (GI) motility. This study aimed to investigate the dynamic regulatory mechanisms of the ENS-SIP system on colon motility during postnatal development. Colonic samples of postnatal 1-week-old (PW1), 3-week-old (PW3), and 5-week-old (PW5) mice were characterized by RNA sequencing, qPCR, Western blotting, isometric force recordings (IFR), and colonic motor complex (CMC) force measurements. Our study showed that the transcriptional expression of Pdgfrα, c-Kit, P2ry1, Nos1, and Slc18a3, and the protein expression of nNOS, c-Kit, and ANO1 significantly increased with age from PW1 to PW5. In PW1 and PW3 mice, colonic migrating movement was not fully developed. In PW5 mice, rhythmic CMCs were recorded, similar to the CMC pattern described previously in adult mice. The inhibition of nNOS revealed excitatory and non-propulsive responses which are normally suppressed due to ongoing nitrergic inhibition. During postnatal development, molecular data demonstrated the establishment and expansion of ICC and PDGFRα+ cells, along with nitrergic and cholinergic nerves and purinergic receptors. Our findings are important for understanding the role of the SIP syncytium in generating and establishing CMCs in postnatal, developing murine colons.

Contractility measurements for cardiotoxicity screening with ventricular myocardial slices of pigs.

Cardiotoxicity is one major reason why drugs do not enter or are withdrawn from the market. Thus, approaches are required to predict cardiotoxicity with high specificity and sensitivity. Ideally, such methods should be performed within intact cardiac tissue with high relevance for humans and detect acute and chronic side effects on electrophysiological behaviour, contractility, and tissue structure in an unbiased manner. Herein, we evaluate healthy pig myocardial slices and biomimetic cultivation setups (BMCS) as a new cardiotoxicity screening approach. Pig left ventricular samples were cut into slices and spanned into BMCS with continuous electrical pacing and online force recording. Automated stimulation protocols were established to determine the force-frequency relationship (FFR), frequency dependence of contraction duration, effective refractory period (ERP), and pacing threshold. Slices generated 1.3 ± 0.14 mN/mm2 force at 0.5 Hz electrical pacing and showed a positive FFR and a shortening of contraction duration with increasing pacing rates. Approximately 62% of slices were able to contract for at least 6 days while showing stable ERP, contraction duration-frequency relationship, and preserved cardiac structure confirmed by confocal imaging and X-ray diffraction analysis. We used specific blockers of the most important cardiac ion channels to determine which analysis parameters are influenced. To validate our approach, we tested five drug candidates selected from the Comprehensive in vitro Proarrhythmia Assay list as well as acetylsalicylic acid and DMSO as controls in a blinded manner in three independent laboratories. We were able to detect all arrhythmic drugs and their respective mode of action on cardiac tissue including inhibition of Na+, Ca2+, and hERG channels as well as Na+/Ca2+ exchanger. We systematically evaluate this approach for cardiotoxicity screening, which is of high relevance for humans and can be upscaled to medium-throughput screening. Thus, our approach will improve the predictive value and efficiency of preclinical cardiotoxicity screening.

Assessing the Amount of Force Necessary to Pick off Cones from Siberian Larch, Scots Pine and Siberian Pine Trees

The article presents the results of studies conducted in Eastern Siberia, dedicated to determining the amount of force required for detachment of Siberian larch, Scots pine and Siberian pine cones, which is one of the main indicators that determines the parameters of cone collecting machines and mechanisms for coniferous species. The pick-off force for the cones was measured at different collection times in the upper, middle, and lower parts of the crown and at different angles of pull-off force direction. The limits of these forces variability are: for the Scots pine – 23.5–48.1 N, for the Siberian larch – 27.5–42.2 N; for the Siberian pine – 3.9–7.8 N. The data obtained can serve as a basis for calculating the parameters of cone collecting mechanisation tools for the aforementioned species. When designing machines and mechanisms for collecting the coniferous trees’ cones, it is necessary to have initial data that determine the parameters of the working bodies. One of these parameters is the amount of effort required to separate the cones from the branches. The forces of detaching cones from trees in the European part of Russia were determined by a number of researchers. According to I.M. Zima with co-authors (1966), the force of detachment of cones in Scots pine (Pinus sylvestris L.) is 41.2 N. According to I.A. Lavrov (1970), pine cones can be torn off with a force of 21.1 N, and the cones of Siberian larch (Larix sibirica Ledeb) – with a force of 39.2 N. In Siberia, studies on the cones detachment were first carried out in 1970 by the laboratory of mechanization of the forest seeds collection and processing of the ASRIM forestry enterprise (Orlovsky et al., 2016). The detachment of Siberian larch, Scots pine and Siberian pine cones was studied in the forestry enterprises of the Krasnoyarsk and Altai regions and in the Republic of Tyva. The pull-off forces of Scots pine and Siberian larch cones were measured in the lower, middle, and upper parts of the crowns using dynamometers with a 0.1 N division value and with a maximum force recording device. The measurements were carried out along the branch, at an angle of 40°–50° and at an angle of 90° to the branch.

An In Vivo Study Using T-scan III Occlusal Analysis System: Does the Extraction Pattern Affect the Final Occlusion in Orthodontics?

The assessment of an orthodontic patient's occlusion throughout the treatment and after debonding permits the orthodontist to improve functional occlusion through interventional tooth movements, thus rendering the overall treatmentmore efficient in terms of stability and masticatory efficiency. This study aimed to evaluate the effect of four first premolarextractions during orthodontic treatment on the distribution of bite force using the T-scan III system (Tekscan Inc., Boston, MA). We aim to evaluate the effect of four first premolarextractions during orthodontic treatment on bite force distribution. Ten patients (mean age: 16 ± 2.72 years), who would be treated orthodontically with four first premolar extractions to treat their teeth crowding, were selected for this study. The T-scan III system was utilized to measure the occlusal bite force of the patients before and after treatment, and the findings were compared. There was a non-statistically significant decrease in the occlusal bite force's mean in the arch's anterior segment from 24.45% (± 8.50%) to 14.25% (± 12.93%) after the orthodontic treatment. A non-statistically significant increase in the occlusal bite force in the posterior right segment of the arch from 37.64% (± 18.13%) to 41.65% (± 11.52%) was found after the treatment. The occlusal bite force in the posterior left segment of the arch increased insignificantly from 30.53% (± 20.00%) to 43.95% (± 13.22%). There was an even distribution of bite force on both sides of the arch by the end of the treatment. Orthodontic treatment helps to achieve a functional occlusal balance by assisting in the uniform distribution of biting force on both sides of the arch. There was no statistically significant change in the distribution of bite force recordings collected before and after orthodontic treatment, indicating that the removal of the four first premolar teeth does notimpact the functional aspect of occlusion. The T-scan III system serves as an essential guide during orthodontic treatment to monitor occlusal changes.