Flexible Polymer Dispersed Liquid Crystal Research Articles

The effect of liquid crystal concentration on electrooptical properties of five flexible polymer dispersed liquid crystal formulations

We investigated the effect of concentration on the electro-optical properties of some flexible PDLC formulations with various liquid crystal mixtures. The PDLC films were prepared on flexible ITO-PET supports by UV-PIPS phase separation method and the uniform film thickness was insured by plastic micro-spacers. We found that depending on the type of liquid crystal and PDLC process conditions, the electro-optical properties (off-state and on-state transmissions, switching voltages and response times) provide different concentration dependency with various trends in the studied flexible PDLC formulations.

Mechanically flexible multi-stacked ITO/PEDOT:PSS hybrid superlattice films for transparent conductive electrodes

To improve the flexibility of transparent conductive electrodes (TCEs), we designed multi-stacked ITO/PEDOT:PSS hybrid superlattice (IxPy) films for flexible polymer-dispersed liquid crystal (PDLC), foldable thin-film heaters (TFHs), and flexible perovskite solar cells (PSCs). The electrical and optical properties of the multi-stacked IxPy films were examined and then optimized at the I6P5 film (ITO: 6 layers and PEDOT: 5 layers). The I6P5 film showed a sheet resistance of 149.66 Ohm/square, high transmittance of 93.75% at the visible range of (400–800) nm, and achieved the highest figure-of-merit (FOM) value of 3.50 × 10−3, compared with the other stacked conditions. Furthermore, the I6P5 films showed better flexibility by suppressing the brittle nature of ITO through inserting very thin PEDOT:PSS. The I6P5 film as an electrode was employed as a flexible PDLC, flexible TFHs, and flexible PSCs. The I6P5-based PDLC showed a clear distinction between on-state and off-state. At the applied voltage of 60 V, the transmittance of PDLC increased to 48.829% because of the arrangement of liquid crystals in the current direction. The flexible TFHs with I6P5 superlattice electrode showed high saturation temperature of above 100 °C at 14 V. Moreover, the I6P5 electrodes showed similar efficiency to reference ITO films in flexible PSCs. These results indicate that the multi-stacked IxPy hybrid superlattice films offer superior potential as highly transparent and foldable or flexible conductive electrodes.

ALD Deposited ZnO:Al Films on Mica for Flexible PDLC Devices.

In this work, highly conductive Al-doped ZnO (AZO) films are deposited on transparent and flexible muscovite mica substrates by using the atomic layer deposition (ALD) technique. AZO-mica structures possess high optical transmittance at visible and near-infrared spectral range and retain low electric resistivity, even after continuous bending of up to 800 cycles. Structure performances after bending tests have been supported by atomic force microscopy (AFM) analysis. Based on performed optical and electrical characterizations AZO films on mica are implemented as transparent conductive electrodes in flexible polymer dispersed liquid crystal (PDLC) devices. The measured electro-optical characteristics and response time of the proposed devices reveal the higher potential of AZO-mica for future ITO-free flexible optoelectronic applications.

Atomic Layer-Deposited Al-Doped ZnO Thin Films for Display Applications

The integration of high uniformity, conformal and compact transparent conductive layers into next generation indium tin oxide (ITO)-free optoelectronics, including wearable and bendable structures, is a huge challenge. In this study, we demonstrate the transparent and conductive functionality of aluminum-doped zinc oxide (AZO) thin films deposited on glass as well as on polyethylene terephthalate (PET) flexible substrates by using an atomic layer deposition (ALD) technique. AZO thin films possess high optical transmittance at visible and near-infrared spectral range and electrical properties competitive to commercial ITO layers. AZO layers deposited on flexible PET substrates demonstrate stable sheet resistance over 1000 bending cycles. Based on the performed optical and electrical characterizations, several applications of ALD AZO as transparent conductive layers are shown—AZO/glass-supported liquid crystal (LC) display and AZO/PET-based flexible polymer-dispersed liquid crystal (PDLC) devices.

Pulsed Electrodeposition for Copper Nanowires

Copper nanowires (Cu NWs) are a promising alternative to indium tin oxide (ITO), for use as transparent conductors that exhibit comparable performance at a lower cost. Furthermore, Cu NWs are flexible, a property not possessed by ITO. However, the Cu NW-based transparent electrode has a reddish color and tends to deteriorate in ambient conditions due to the oxidation of Cu. In this paper, we propose a pulsed-current (PC) plating method to deposit nickel onto the Cu NWs in order to reduce oxidation over a 30-day period, and to minimize the sheet resistance. Additionally, the effects of the pulse current, duty cycle, and pulse frequency on the performance of the Cu–Ni (copper–nickel) NW films have also been investigated. As a result, the reddish color of the electrode was eliminated, as oxidation was completely suppressed, and the sheet resistance was reduced from 35 Ω/sq to 27 Ω/sq. However, the transmittance decreased slightly from 86% to 76% at a wavelength of 550 nm. The Cu–Ni NW electrodes also exhibited excellent long-term cycling stability after 6000 bending cycles. Our fabricated Cu–Ni electrodes were successfully applied in flexible polymer-dispersed liquid crystal smart windows.

Spray Deposition of Ag Nanowire⁻Graphene Oxide Hybrid Electrodes for Flexible Polymer⁻Dispersed Liquid Crystal Displays.

We investigated the effect of different spray-coating parameters on the electro-optical properties of Ag nanowires (NWs). Highly transparent and conductive Ag NW–graphene oxide (GO) hybrid electrodes were fabricated by using the spray-coating technique. The Ag NW percolation network was modified with GO and this led to a reduced sheet resistance of the Ag NW–GO electrode as the result of a decrease in the inter-nanowire contact resistance. Although electrical conductivity and optical transmittance of the Ag NW electrodes have a trade-off relationship, Ag NW–GO hybrid electrodes exhibited significantly improved sheet resistance and slightly decreased transmittance compared to Ag NW electrodes. Ag NW–GO hybrid electrodes were integrated into smart windows based on polymer-dispersed liquid crystals (PDLCs) for the first time. Experimental results showed that the electro-optical properties of the PDLCs based on Ag NW–GO electrodes were superior when compared to those of PDLCs based on only Ag NW electrodes. This study revealed that the hybrid Ag NW–GO electrode is a promising material for manufacturing the large-area flexible indium tin oxide (ITO)-free PDLCs.

Flexible, ferroelectric nanoparticle doped polymer dispersed liquid crystal devices for lower switching voltage and nanoenergy generation

Flexible polymer dispersed liquid crystal (F-PDLC) devices were fabricated using transparent conducting ITO/PET film. Polymerization induced phase separation (PIPS) method was used for pure and ferroelectric BaTiO3 (BTO) and ZnO doped PDLC devices. The distribution of nanoparticles in the PDLC and the formation of micro cavities were studied using field emission scanning electron microscopy (FESEM). It was observed that the addition of ferroelectric BTO nanoparticles has reduced the threshold voltage (Vth) and saturation voltage (Vsat) of FNP-PDLC by 85% and 41% respectively due to the spontaneous polarization of ferroelectric nanoparticles. The ferroelectric properties of BTO and ZnO in the fabricated devices were investigated using dynamic contact electrostatic force microscopy (DC EFM). Flexing the device can generate a potential due to the piezo-tribo electric effect of the ferroelectric nanomaterial doped in the PDLC matrix, which could be utilized as an energy generating system. The switching voltage after multiple flexing was also studied and found to be in par with non-flexing situations.

Amino-functionalized sub-40 nm ultrathin Ag/ZnO transparent electrodes for flexible polymer dispersed liquid crystal devices

Various flexible transparent conducting electrodes (FTCEs) have been studied for promising applications in flexible optoelectronic devices, but there are still challenges in achieving higher transparency and conductivity, lower thickness, better mechanical flexibility, and lower preparation temperatures. In this work, we prepared a sub-40 nm Ag(9 nm)/ZnO(30 nm) FTCE at room temperature, where each layer played a relatively independent role in the tailoring of the optoelectronic properties. A continuous and smooth 9-nm Ag thin film was grown on amino-functionalized glass and polyethylene terephthalate (PET) substrates to provide good conductivity. A 30-nm ZnO cladding, as an antireflection layer, further improved the transmittance while hardly affecting the conductivity. The room-temperature grown sub-40 nm Ag/ZnO thin films on PET substrate exhibited a transmittance of 88.6% at 550 nm and a sheet resistance of 7.6 Ω·sq−1, which were superior to those of the commercial ITO. The facile preparation benefits the integration of FTCEs into various flexible optoelectronic devices, where the excellent performance of the sub-40 nm Ag/ZnO FTCEs in a flexible polymer dispersed liquid crystal device was demonstrated. Sub-40 nm Ag/ZnO FTCEs that have the characteristics of simple structure, room-temperature preparation, and easily tailored optoelectronic properties would provide flexible optoelectronic devices with more degrees of freedom.

Ultrasensitive Multi-Functional Flexible Sensors Based on Organic Field-Effect Transistors with Polymer-Dispersed Liquid Crystal Sensing Layers

Ultrasensitive flexible sensors with multi-sensing functions are required for various applications in flexible electronics era. Here we demonstrate flexible polymer-dispersed liquid crystal (PDLC)-integrated-organic field-effect transistors (OFETs) (PDLC-i-OFETs), which sensitively respond to various stimulations including weak gas (air) flow, direct physical touch, light, and heat. The flexible PDLC-i-OFETs were fabricated by spin-coating the poly(methyl methacrylate) (PMMA)-dispersed 4,4’-pentyl-cyanobiphenyl (5CB) layers on the poly(3-hexylthiophene) (P3HT) channel layers of OFETs with 200 μm-thick poly(ethylene naphthalate) (PEN) substrates. The flexible PDLC-i-OFET devices could sense very weak nitrogen gas flow (0.3 sccm), which cannot be felt by human skins, and stably responded to direct physical touches (0.6~4.8 g load). In addition, the present devices showed very sensitive photoresponses to a visible light and exhibited excellent heat-sensing characteristics at a temperature of 25~70 °C. In particular, the present flexible PDLC-i-OFET devices could sense two different stimulations at the same time, indicative of promising multi-sensing capabilities.

Flexible polymer dispersed liquid crystal film with graphene transparent electrodes

A flexible polymer-dispersed liquid crystal (PDLC) film with graphene layers as transparent electrodes was fabricated by combining a UV curable polymer and a nematic liquid crystal. The PDLC film with a dimension of 5 × 10 cm2 was flexible and operated normally with no damage when it was bent with a radius of 2 mm. Instead of using conventional transparent conducting film, the single-layer-graphene transferred on PET film was used as transparent electrodes. The thickness of the graphene-PDLC was about 210–220 μm. The single-layer-graphene grown by thermal chemical vapor deposition was transferred onto the PET film, and its sheet resistance was about 1.2 kΩ/□. The controllable transmission range between the on and off states was about 60% in the visible range. The response time for the turn-on and off processes were estimated to be 0.3 and 32 ms, respectively. This successful fabrication of graphene based PDLC is a crucial step toward paving the way for the commercialization of the emerging material, graphene.

Flexible Polymer Dispersed Liquid Crystal Module with Graphene Electrode.

Flexible polymer dispersed liquid crystal (PDLC) module based on graphene electrode was presented in this article. We also investigated electromechanical, as well as electro-optical properties of PDLC module with graphene electrodes. Compared to the ITO electrodes, graphene electrodes exhibits higher light transmittance and more stable electromechanical property of under bend test. Due to the excellent mechanical property of graphene electrodes, it is expected that the flexibility of PDLC module could be further enhanced. Meanwhile, with the integration of graphene as the driving electrodes, the threshold voltage V(th) and saturation voltage V(sat) of PDLC module have small change, while the on-state transmittance T(on) is increased by 5%, that may attribute to the high transmittance of the graphene.

The surface rubbing effect on morphologies of LC droplets and electro-optic properties of flexible PDLC films

The flexible polymer dispersed liquid crystal (PDLC) film with threshold voltage V10 and saturation driving voltage V90 as low as 0.34 V/μm and 0.77 V/μm, respectively, has been prepared successfully by polymerization induced phase separation (PIPS). The surface rubbing effect on morphologies of liquid crystals (LC) droplets and electro-optic properties of PDLC films has been studied experimentally and theoretically. We use a CVC (Color Video Camera) and a SEM (Scan Electron Microscope) to detect and characterize morphologies of LC droplets in the net of polymer. The result reveals that almost all the smaller LC droplets exhibit in the rubbing direction uniformly, and the texture of PDLC is similar to that of H-PDLC. Meanwhile, compared with the sample of the non-rubbing disposal, the response time declines evidently by 11.2 ms (i.e., the rising time τrise) and 27.2 ms (i.e., the decaying time τdown), and the contrast ratio is improved from 18.5 to 35.9. Such a result can be attributed to the surface rubbing effect.

Fabrication of flexible polymer dispersed liquid crystal films using conducting polymer thin films as the driving electrodes

Conducting polymers exhibit good mechanical and interfacial compatibility with plastic substrates. We prepared an optimized coating formulation based on poly(3,4-ethylenedioxythiophene) (PEDOT) and 3-(trimethoxysilyl)propyl acrylate and fabricated a transparent electrode on poly(ethylene terephthalate) (PET) substrate. The surface resistances and transmittance of the prepared thin films were 500–600 Ω/□ and 87% at 500 nm, respectively. To evaluate the performance of the conducting polymer electrode, we fabricated a five-layer flexible polymer-dispersed liquid crystal (PDLC) device as a PET-PEDOT-PDLC-PEDOT-PET flexible film. The prepared PDLC device exhibited a low driving voltage (15 VAC), high contrast ratio (60:1), and high transmittance in the ON state (60%), characteristics that are comparable with those of conventional PDLC film based on indium tin oxide electrodes. The fabrication of conducting polymer thin films as the driving electrodes in this study showed that such films can be used as a substitute for an indium tin oxide electrode, which further enhances the flexibility of PDLC film.