Finite Metallization Thickness Research Articles

Optical pulling force on dielectric particles via metallic slab surface plasmon excitation: a comparison between transmission and reflection schemes.

In this Letter, a simple structure formed by a metallic thin layer covering a high-index substrate is used to design an optical tweezer. Owing to the interaction between the field scattered by the particle with an incident plane wave and the proposed structure, a pulling or attractive component of the optical force emerges. This component results in enhancement thanks to the surface plasmons (SPs) excitation arising from the elliptical polarization of the induced dipole moment on the particle. To further exploit the versatility of the proposed approach, we analyze two basic configurations: the reflection scheme, for which the plane wave impinges from the side where the particle is placed; and the transmission scheme, for which the incidence is made from the substrate side. Our results show that the intensity of the pulling force in the reflection scheme and for finite thickness metal layer reaches values exceeding more than twice those provided by a single metallic interface. We also demonstrate that the transmission scheme is more favorable than the reflection scheme for enhancing pulling force intensities. Our contribution can be valuable for realizing simple plasmonic schemes for improving the pulling force via interactions between the nano-particle and SP fields.

Pore-scale numerical simulation and LTNE analysis for fully-developed forced convective heat transfer in packed beds of mono-sized rough spheres covering near-wall and core regions

This work presents a novel method to acquire the effective convection heat transfer coefficients on the interfaces of wall-fluid contacts and sphere-fluid in both the near-wall region and core region of sphere-packed beds. Pore-scale numerical simulations are first conducted for different porosities pertaining to two regular body-centered cubic and face-centered cubic packings, packing lattice angles, inflow velocities, and ratios of the thermal conductivities of the solid and fluid. A finite-thickness metal reactor wall is included in the pore-scale simulation to make the heating boundary conditions more realistic. The outer surface of the metal wall is subjected to a uniform heat flux. The heat then passes through the metal wall and dispenses into the solid and liquid phases of the packed bed through the wall-sphere and the wall-fluid interfaces at the inner wall according to the physical mechanisms. Within the reactor, the heat transfer mechanism is separately considered in the near-wall region and the core region due to the intrinsic differences in the flow pattern. For each packing, different inflow angles are examined and exhibit different flow patterns and heat transfer performances. After the whole domain is hydrodynamically and thermally fully-developed, the local effective convection heat transfer coefficients can then be calculated. These coefficients reflect the realistic local convection either on the reactor wall or on the sphere-fluid interface. These convection heat transfer coefficients, along with the effective solid thermal conductivity through the contacting spheres obtained in our previous work, are implanted into a modified two-equation LTNE model. This modified LTNE model yields linear longitudinal fully-developed temperature distributions within the reactor having discrepancies in the temperature slopes less than ±10% from those by the pore-scale numerical simulations. In contrast, the conventional model even fails to reach linear distributions of the solid- and liquid-phase temperatures, which are expected for fully-developed packed-bed flows.

Theoretical study on hole evolution of inclination finite thickness metal plate impacted by shaped charge jet

In the armor design field, the asymmetric interaction between various hypervelocity penetrators and the inclined targets is an important topic. However, most existing studies overlook the influence of asymmetry on the expansion of the initial penetration hole. A modified theoretical model for predicting the hole radii of hypervelocity penetrator impacting an inclined thin plate was derived in this research. According to a set of experimental results, the empirical parameters of the resistance strength term as a function of the oblique angle in this model were obtained. The theoretical predictions have excellent agreement with a series of simulation results as performed with an ANSYS/AUTODYN solver.

Oblique penetration of tungsten alloy rod to finite-thickness metal plate

Abstract In order to study the critical ricochet velocity and critical penetration velocity of tungsten alloy rod obliquely penetrating a finite-thickness metal plate, experiment and numerical calculation of tungsten alloy rod impacting on homogeneous armor steel plate with a thickness of 30mm at an angle of 60° were carried out. Compared the experimental and numerical results with the results using models, it is found that, the results of the ricochet models proposed by Tate, Rosenberg and Steven B for semi-infinite thick plate are quite different from those of experiment and numerical calculation, so they can not be applied to the ricochet situation of finite-thickness plate. The critical penetration velocity model proposed by De Marre and Zhao are in good agreement with the numerical and experimental results, which can predict critical penetration velocity of tungsten alloy rod obliquely penetrating a finite-thickness metal plate with large impact angle. The penetration depth of the projectile under the critical ricochet velocity is about 1/3 of the thickness of the target plate, and the angle between the ejection trajectory of the fragments produced by projectile and target plate and projectile penetration trajectory is exactly 90° in the first penetration stage.

Plasmonic finite-thickness metal–semiconductor–metal waveguide as ultra-compact modulator

We propose a plasmonic waveguide with semiconductor gain material for optoelectronic integrated circuits. We analyze properties of a finite-thickness metal–semiconductor–metal (F-MSM) waveguide to be utilized as an ultra-compact and fast plasmonic modulator. The InP-based semiconductor core allows electrical control of signal propagation. By pumping the core we can vary the gain level and thus the transmittance of the whole system. The study of the device was made using both analytical approaches for planar two-dimensional case as well as numerical simulations for finite-width waveguides. We analyze the eigenmodes of the F-MSM waveguide, propagation constant, confinement factor, Purcell factor, absorption coefficient, and extinction ratio of the structure. We show that using thin metal layers instead of thick ones we can obtain higher extinction ratio of the device.

Microfluid Permittivity Measurement Based on On-Chip CPW with Finite Metal Thickness

A new method of permittivity measurement based on the on-chip coplanar waveguide (CPW) with finite metal thickness without close box or microfluid channel is presented in this paper. The material under test (MUT) is directly located in the slot line of the CPW which is considered to be the strongest field distribution area. The proposed structure sample is simulated through HFSS. The simulation results agree well especially when the metal thickness is comparable with the slot line width, the errors are less than 5%.

The effects of finite metallisation thickness and conductivity in microstrip lines

PurposeThe purpose of this paper is to study and discuss the effects of the finite metallisation thickness and conductivity on the properties of microstrip lines.Design/methodology/approachEffective dielectric constant and attenuation constant of microstrip lines with finite metallization thickness and finite conductivity are analyzed by the method of lines. The experimental results are obtained by using Vector Network Analyzer and the 3680 V Universal Test Fixture of Anritsu.FindingsThe strip thickness has a great impact on the attenuation constant of the microstrip lines. The effects can be divided into three parts by the relationship between strip thickness (t) and skindepth (δ). When t<δ, the attenuation constant will decrease rapidly as the strip thickness increase. When δ < t<2δ, the attenuation constant still decrease rapidly as the strip thickness increase, but the slope of the curve will be smaller. When 2δ < t, the effects of the strip thickness will become insignificant and the attenuation constant still decrease slowly as the strip thickness increase.Originality/valueThis paper presents some useful principles about the effects of the finite metallization thickness and finite conductivity in microstrip lines. The reasons for these effects are discussed by analyzing the longitudinal electric field distribution in the strip. Finally, some experimental results are given to verify these principles.

Channel and wedge plasmon modes of metallic V-grooves with finite metal thickness

We investigate numerically the effect of a finite metal film thickness on the propagation characteristics of the channel Plasmon polariton (CPP) and wedge plasmon polariton (WPP) modes, both in a symmetric and asymmetric environment. We observe that decreasing the metal thickness results in an improvement of the field localization near the groove tip and an increase of the losses for both types of mode. This behavior stems from the typical symmetric charge distribution of both modes across the metal film. When considering an asymmetric dielectric environment, the CPP mode is found to evolve into short range Plasmon modes propagating along the groove walls, in contrast to the WPP mode which remains essentially confined at the tip apex. These results can be useful to tailor the properties of such plasmon modes, using the metal thickness as the variable parameter.

Transverse surface waves in a functionally graded piezoelectric substrate coated with a finite-thickness metal waveguide layer

An analytical study on transverse surface waves propagating in a functionally graded piezoelectric substrate carrying a metal layer of finite thickness was carried out. Dispersion relations for the existence of the waves were obtained and the effects of material gradient on wave propagation were quantified. Numerical examples show that the presence of the material gradient affects significantly the fundamental mode but has only negligible effects on the higher order modes. Depending on whether the surface wave velocity is smaller or greater than the bulk shear wave velocity in the metal layer, three different types of the dispersion behavior are discussed.

Modulation of Bleustein-Gulyaev Waves in a Functionally Graded Piezoelectric Substrate by a Finite-thickness Metal Waveguide Layer

Modulation of Bleustein-Gulyaev Waves in a Functionally Graded Piezoelectric Substrate by a Finite-thickness Metal Waveguide Layer

Dynamic Analysis Of Multilayered Microwave Circuits Including Metallization Effects

In this paper, the dynamic spectral domain approach is generalized to efficiently describe the dispersion properties of planar microwave circuits by considering any arbitrary metallization thickness and finite conductivity in multilayer configuration. The influence of finite metallization thickness on the frequency-dependent modal propagation characteristics is demonstrated for both single and coupled structures and can, for the first time, be easily extended to any multilayered circuit. The phase constant and the effective permittivity with finite strip thickness and finite conductivity are discussed for hybrid and monolithic circuits. Numerical results are presented and the CPU time is investigated.

Control of 2D plasmon-polariton mode with dielectric nanolayers

We introduce two nanoscale thickness dielectric layers on the top and bottom sides of a finite width and finite thickness metal microstrip and have calculated the fundamental symmetric plasmon-polariton mode of the 2D metal-dielectric layer waveguide. The dielectric nanolayers provide an additional degree of freedom to control the plasmon-polariton mode. When the dielectric constant of the nanolayers is smaller than that of the cladding dielectric, the travel range of the fundamental symmetric plasmon-polariton mode is extended with the trade-off of the mode confinement. The figure of merit of the mode increases as the travel range extends.

Theoretical Investigation of Metal Cladding for Nanowire and Cylindrical Micropost Lasers

We investigate the transverse modal properties of cylindrical subwavelength metal-clad nanowire and micropost lasers via rigorous theoretical waveguide analysis, including the effects of finite thickness metal cladding and gain in the core. The results of this analysis show that air-metal surface guided TM <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">01</sub> and some hybrid surface guided modes suffer less loss but are less confined to the core, while core-metal surface guided modes are better confined to the core but suffer greater loss. An increase in the thickness of the metal cladding reduces the loss of the core-metal surface guided modes. The modal gain and confinement of the metal-clad cavity are compared to an unclad cavity.

Casimir force between thin films of real metals

The Casimir force between two finite-thickness metal films has been calculated for realistic plasma frequencies of metals. The result obtained indicates the possibility of weakening of the Casimir force for real films by approximately an order of magnitude at the appropriate choice of the parameters in qualitative agreement with the existing experimental data.

Analytical calculation for DC inductances of rectangular spiral inductors with finite metal thickness in the PEEC formulation

Inductances of rectangular spiral inductors with finite metal thickness are evaluated by the partial element equivalent circuit (PEEC) technique. The six-fold partial self and mutual inductance integrals resulting from the PEEC partitions are found to have analytical expressions, so that the singularities of the integrands can be overcome and the theoretical or "exact" results can be obtained very efficiently. Via and underpath required for input/output connection can also be included in the calculation. Calculated inductance values for 20 square spiral inductors are checked against measured data published in open literature. Dependence of inductance values on metal thickness is investigated for two specific spiral structures.

Extended long range plasmon waves in finite thickness metal film and layered dielectric materials

In this paper, we show that the propagation distance of the long range plasmon wave mode guided by a finite thickness gold metal film can be extended several orders of magnitude longer if we place intermediate dielectric layers on both sides of the metal film and choose the layer thickness properly. The propagation distance goes to infinite if the intermediate layer thickness approaches a critical thickness.

Efficient Electromagnetic Analysis of Line-Fed Aperture Antennas in Thick Conducting Screens

This paper presents a numerical and experimental verification of an approximate but efficient integral equation technique for the scattering by apertures in conducting planes with finite thicknesses. The approach is based on a perturbation method and modified Green's functions that take into account the finite metallization thickness. The computational effort and time needed for solving the problem are the same as in zero-thickness case. When compared to full-wave cavity treatment of thick apertures, the method is (depending on the number of unknowns) at least an order of magnitude faster. The method can be applied even to apertures of arbitrary shapes where computing the cavity's Green's functions is a difficult task. The results of simulations using the new approach show good agreement when compared to both results from full-wave cavity approach and measurements.

Design of tight coupled backward-wave directional coupler using coupled lines with dielectric guide and finite metallisation thickness

A design for a tight coupled backward-wave directional coupler using coupled lines with dielectric guide between two finite metal strips is described. A mode-matching method, simple and fast quasi-static analysis, has been used to analyse the propagation characteristics of the structure. To provide the validity of the results obtained, comparison with other available data is made. The numerical results confirm that, with the use of dielectric guide in addition to finite metal conductors, it is possible to overcome the shortcomings of the conventional backward-wave directional coupler such as weak coupling, low directivity and extremely narrow gap distance for tight coupling, which are very difficult to realise. It is clearly shown that the dielectric guide between two strips and finite metallisation thickness can be new parameters for tight coupling in the design of backward-wave directional couplers, and this allows the RF designer another control variable in the design of high-performance three-dimensional monolithic microwave integrated circuits.

An Efficient Analysis of Shielded Single and Multiple Coupled Microstrip Lines With the Nonuniform Fast Fourier Transform (NUFFT) Technique

A nonuniform fast Fourier transform (NUFFT) technique is incorporated into the spectral-domain approach for the analysis of shielded single and multiple coupled microstrip lines. Each of the spectral-domain Green's functions is decomposed into an asymptotic part and a remaining part. At the interface of layered dielectrics with conducting strips, the product of a basis function and an associated Green's function constitutes an expansion E-field. The inverse Fourier transform (IFT) of the expansion E-field is its spatial distribution all over the interface. We take this advantage to match the final boundary conditions on all the conducting strips simultaneously. As a result, if all the strips are at one interface, the number of operations required in this method is proportional to N/sub /spl lscr//, but not to N/sub /spl lscr///sup 2/, where N/sub /spl lscr// is the number of the strips. The IFT of the asymptotic part of each expansion E-field can be obtained analytically, and that of the remaining part can be quickly processed by the NUFFT. The Gauss-Chebyshev quadrature is used to accelerate the computations of the integrals resulted from the Galerkin's procedure. The proposed method is also applied to investigate the dispersion characteristics of coupled lines with finite metallization thickness and of coupled lines at different levels. A convergence analysis of the results is presented and a comparison of used CPU time is discussed.

Analysis of the Bloch mode spectra of surface polaritonic crystals in the weak and strong coupling regimes: grating-enhanced transmission at oblique incidence and suppression of SPP radiative losses

The Bloch mode spectrum of surface plasmon polaritons (SPPs) on a finite thickness metal film has been analyzed in the regimes of weak and strong coupling between SPP modes on the opposite film interfaces. The SPP mode dispersion and associated field distributions have been studied. The results have been applied to the description of the light transmission through thick and thin periodically structured metal films at oblique incidence. In contrast to normal incidence, all SPP Bloch modes on a grating structure participate in the resonant photon tunnelling leading to the transmission enhancement. However, at the angle of incidence corresponding to the crossing of different symmetry film SPP Bloch modes, the far-field transmission is suppressed despite the enhanced near-field transmission. The combined SPP mode consisting of the two film SPPs having different symmetries that is achieved at the crossing frequency exhibits no radiative losses on a structured surface.