Filter Device Research Articles

Development of Low-Stress Double-Pass Filter Device for Methane and Ethane Flammable Gas Detection System

To meet the needs of industrial and environmental monitoring of methane and ethane flammable gases, a low-stress filter device for detecting methane and ethane simultaneously is developed based on the absorption spectra of methane and ethane and the thin-film design theory. In order to improve the sensitivity of the detection system and reduce the influence of environmental noise, the information of methane and ethane gas is extracted simultaneously by using a filter with double bandpass and wide cut-off in the middle-infrared and far-infrared bands. The transmittance of the filter is 91.3%, 93.1%, and 93.02% at the wavelengths of 3.31 μm, 6.71 μm, and 7.67 μm, respectively. The cut-off depth in the cut-off interval is above OD3, which meets the system’s requirements.

Nacre-inspired graphene oxide/polyethyleneimine-based ultra-thin heterogeneous superwetting membrane for highly stable separation of oil-in-water emulsions

Since the massive discharge of oily wastewater seriously affects both humans and natural development, the performance of conventional membrane materials in terms of interfacial stability and antifouling in the treatment of surfactant-containing emulsified oily wastewater is a major challenge. In this work, a novel nacre-inspired graphene oxide/polyethyleneimine-based ultra-thin chemically heterogeneous superwetting membrane was fabricated through vacuum-assisted self-assembly and post-modification methods for oil-in-water emulsion separation. The nacre-inspired heterogeneous membrane exhibited superhydrophilicity, underwater superoleophobicity (underwater oil contact angle was 157.7°), excellent crude oil adhesion resistance, high acid/alkaline stability, outstanding salt resistance, and good mechanical properties (Young’s modulus 1391.7 MPa). The heterogeneous membranes showed separation efficiencies of more than 99.9 % for a range of oil-in-water emulsions. The high-value membranes could achieve the permeances of 917–1256 L m−2h−1 bar−1 for pure water and 339.7–577 L m−2h−1 bar−1 for emulsion through a dead-end filter device, with the optimal long-term stable permeance only decreasing by 30.0 % compared to the initial value. After six test cycles, the membrane’s antifouling and self-cleaning properties were enhanced by constructing heterogeneous superwetting properties, and the flux recovery rate remained at 96.5 %. All of these results indicated that this method provides new ideas for the design and fabrication of highly stable and antifouling membrane materials.

Thermoelectric and optoelectronic features of C- and N- doped CsZnBr3 halide perovskite for use in spin filter and energy efficient devices

Present study reports mainly thermoelectric and optical properties followed by its structural, electronic, magnetic properties of CsZnBr3 halide perovskite using full potential linearized augmented plane wave method in the framework of density functional theory. Further we analyzed the impact of C and N on CsZnBr3 for their electronic structure, magnetic nature, thermoelectric, and optical properties. CsZnBr3 under optimum conditions exhibits a non-magnetic phase, which interestingly upon doping of C and N, turns out to be ferromagnetic with magnetic moments of 3.0 and 2.0 μB for CsZnBr2C and CsZnBr2C, respectively. Furthermore, Semiconducting CsZnBr3 exhibits spin filter semiconductor nature with energy band gaps of 1.38↑ and 3.26↓ eV for CsZnBr2C and 2.72↑ and 1.67↓ eV for CsZnBr2N. These doped materials can be used in spintronics as spin-filter devices for lower power consumption leading to more energy-efficient electronics. The thermoelectric parameters as Seebeck coefficient, power factor, thermal conductivity and figure of merit are estimated using BoltzTrap code. The figure of merit value found enhanced from 0.88 to 1.06 with one orientation of spins for CsZnBr2C at high temperature, which suggests its potential use in thermoelectric applications. In optical reference photon energy can be absorbed in UV-region.

Magnetic tunnel junction based on bilayer LaI2 as perfect spin filter device

The discovery of van der Waals intrinsic magnets has expanded the possibilities of realizing spintronics devices. We investigate the transmission, tunneling magnetoresistance ratio, and spin injection efficiency of bilayer LaI2 using a combination of first-principles calculations and the non-equilibrium Green’s function method. Multilayer graphene electrodes are employed to build a magnetic tunnel junction with bilayer LaI2 as ferromagnetic barrier. The magnetic tunnel junction turns out to be a perfect spin filter device with an outstanding tunneling magnetoresistance ratio of 653% under a bias of 0.1 V and a still excellent performance in a wide bias range. In combination with the obtained high spin injection efficiency this opens up great potential from the application point of view.

Target-specific affinity separation of the bioactive compounds from herbal extract using the spin column packed with the immobilized protein microspheres prior to LC-MS analysis

Excellent pretreatments before instrumental analysis are critical for separation and determination of target compounds for discovery of new drugs from herb medicines. We developed a rapid and highly-selective method to separate the bioactive compounds from herbal extract using protein affinity-selection spin column, which was packed with the new sorbent materials from integrating the recombinant β2-adrenoceptor (β2-AR) directly out of cell lysates onto the surface of microspheres. Protein affinity-selection spin column was placed in a centrifugal tube, where after the non-specific binders were released to the filtrate under the operational centrifugation, the specific binders on the spin column were cleaned with a washing solvent for LC-MS analysis. The known agonists of β2-AR were retained/released on protein affinity-selection spin column but not on control column, demonstrating the method with good recovery (79.4∼95.7 %) and high repeatability (RSD < 3.5 %). The adsorption features of three ligands on the spin column were described best by Prism saturation binding model, and the high-affinity binding and the large binding capacity of the spin column make it feasible to trap the trace analytes effectively. It was applied in separating bioactive compounds from Alstoniae Scholaris extract, two of which were identified as picrinine and oleanolic acid in combination with LC-MS and verified as the potential agonists towards β2-AR though molecular docking and cell experiments. Our study demonstrated that, the spin column with the immobilized protein sorbents in the centrifugal filter device represents a promising tool, enabling rapid and target-specific affinity separation of the bioactive compounds from herbal extract.

Formation mechanism of the U-shaped spectrum based on a simple plasma–dielectric–plasma (PDP) waveguide

Manipulating electromagnetic (EM) waves by plasma–dielectric–plasma (PDP) waveguides or plasma array structures presents significant potential in microwave signal processing, such as filtering, signal delay, and EM enhancement or shielding. Owing to the simple structure and easy fabrication, the waveguide with a tooth-shaped resonator has been a strong candidate as a filtering device. Based on our previous work focusing on U-shaped filtering excited by PDP waveguides with a double-teeth structure, in this work, the formation mechanism of a U-shape filtering spectrum is systematically explored by transmission line theory (TLT) with proper field distributions. The results indicate that the U-shape spectrum consists of boundary edges and a filtering stopband. The boundary edges are attributed to Fano-type resonance, and the enhanced destructive interference from double teeth is responsible for the stopband. Such an approach shows a specific and clear mechanism for the generated U-shaped spectrum. In addition, the theoretical analysis of double teeth without Fano-type resonances is rigorously demonstrated using TLT, which significantly contributes to bandwidth modulation of stopband filtering in theory. These results contribute to the understanding of the formation mechanism of a U-shaped spectrum from a gap plasmon waveguide (such as PDP or metal–insulator–metal (MIM)) with tooth-shaped resonators, offering a feasible direction for the optimization of filtering properties, as well as offering significant parameters for subsequent experimental design.

A simple and cost-effective strategy for electrochemiluminescence spectral determination

BackgroundElectrochemiluminescence (ECL), as a unique and powerful analytical technique, has been widely used in various fields. The determination of ECL spectra plays a crucial role in understanding ECL reaction mechanisms and conducting spectra-resolved ECL analysis. ECL intensity is typically detected using a photomultiplier tube, which offers high sensitivity for detecting extremely weak light signals but does not allow for spectral identification. Due to the time-dependent variation of ECL intensity caused by the applied potential and electrochemical reaction processes, it is challenging to perform ECL spectral detection using conventional wavelength-scanning spectrometers. ResultsIn this study, we present a straightforward and cost-effective ECL spectral detection strategy by incorporating an automatically controlled tunable optical filter device between a commonly used PMT detector and a specially designed ECL reaction cell. The effectiveness of this approach was confirmed through initial validation, where the spectrum of a green LED spotlight was measured and compared with a commercial spectrometer. In a dynamic system with stable ECL signals, the ECL spectrum of the typical Ru(bpy)32+/TPA system was rapidly acquired by adjusting the bandpass filters. To account for time-varying ECL signals in practical measurements, time-based correction algorithms were implemented to rectify variations in ECL intensity. By integrating time-based correction algorithms and an automatically controlled tunable optical filter device into a commonly utilized PMT detector, the rapid and sensitive ECL spectra determination was achieved. Experimental results demonstrated the reliability of the proposed strategy. SignificanceThis strategy is based on the widely used high-sensitivity PMT detection component, enabling the rapid and sensitive measurement of ECL spectra without altering the ECL detection hardware. It is simple, fast, efficient, and cost-effective, with the potential to be widely used for rapid ECL spectral detection and spectra-resolved ECL analysis.

Compressive stress reduction in sputter-deposited yttrium aluminum nitride (Y0.2Al0.8N) thin films for BAW resonators with high electromechanical coupling

In the past decade, rare earth elements have found increasing interest in enhancing the piezoelectric coefficient of aluminum nitride (AlN) thin films. Until now, scandium has been the most successful rare earth element to enhance the piezoelectric coefficient (d33) up to 600 %. In this research paper, we present a 250 % increase in d33 to 12.5 pC/N for sputter-deposited yttrium alloyed aluminum nitride (Y0.2Al0.8N) thin films compared to pure AlN. However, this increase in d33 comes with a substantial increase in compressive layer stress well above 1 GPa. Therefore, a chamber pressure sweep technique is introduced, resulting in a 40 % reduction in the stress level without significantly affecting the crystallographic film parameters to facilitate device integration. Even more, high compressive stress in thin films is a critical concern in piezoelectric MEMS devices such as bulk acoustic wave (BAW) resonators, as it can adversely affect the piezoelectric material properties and hence, the electromechanical performance. For this purpose, we demonstrate that the pressure sweep technique improves the electromechanical coupling factor of Y0.2Al0.8N to 7.02 %, being substantially above the reference value of 6.02 % set by pure AlN. In summary, the findings from this study may stimulate further effort to integrate YxAl1-xN thin films in BAW filter devices for future telecommunication applications.

Single-use chromatographic clarification to eliminate endonuclease treatment in production of recombinant adeno-associated viral vectors

In current manufacturing processes for recombinant adeno-associated viral vectors (rAAV), endonuclease treatment is used prior to depth filtration to break down host cell DNA that is released from cells post-lysis. Without this treatment, traditional depth filters exhibit negligible clearance of host cell DNA, a key process-related impurity. In this work, we evaluate single-use chromatographic clarification using Harvest RCTM filters (3 M) to process rAAV8 and rAAV9 HEK293 cell culture lysate with and without endonuclease pretreatment. We demonstrate endonuclease-free clarification for both serotypes with yield >90 % and up to 3 log reduction of host cell DNA, from >104 ng/mL to <50 ng/mL, matching or exceeding the filtrate quality in traditional depth filtration with 100 U/mL of endonuclease added during lysis. The addition of 100 mM of salt in the harvest buffer is also shown to improve filtration throughput, prevent filter clogging, and limit rAVV binding to the filter device. Finally, a mechanistic cake-fiber fouling model is shown to be a good representation of the Harvest RCTM filtration mechanism. The endonuclease-free clarification approach enables cost savings of USD 100,000 per 500 L batch, equivalent to the cost of cGMP-grade endonuclease at this scale. The benefits of endonuclease-free clarification further include easier raw material sourcing as well as eliminating the need for a residual endonuclease assay in rAAV manufacturing processes.

Inertia–Active Power Filter Design Based on Repetitive Control

The advent of distributed generation has brought with it a plethora of challenges for the nascent power systems that are being deployed on a large scale. Firstly, the majority of power electronic converters connected to the grid are in current source mode, which results in a lack of inertia and an inability to provide effective inertia or achieve damping support during fluctuations in grid frequency. Secondly, the issue of power quality, caused by the presence of harmonics, is becoming increasingly severe. This is particularly problematic in microgrids or systems with high line impedance, where harmonics can be amplified, thereby further compromising the stability of the power system. To address the deficiency in system inertia, numerous scholars are currently utilizing grid-forming (GFM) technology to achieve virtual inertia. In order to address the issue of system harmonics, it is possible to install active power filter (APF) devices at the point of common coupling (PCC), which serve to mitigate the effects of harmonics. This paper puts forth a proposal for the implementation of an APF with virtual inertia, based on PR + RC composite control. This composite control mechanism serves to enhance the harmonic suppression capabilities of the APF. The introduction of a frequency droop enables the capacitor voltage amplitude to be adjusted during fluctuations in system frequency, thereby achieving virtual inertia and providing active support for system frequency. The experimental results demonstrate that this strategy not only reduces the total harmonic distortion (THD) by 13% in comparison to PI control, indicating excellent harmonic suppression performance, but also allows the system to be inert, achieving positive results in suppressing frequency fluctuations during transients.

Conceptual design of visible spectroscopy diagnostics for DTT

The project of the Visible Spectroscopy diagnostics for the Z eff radial profile measurement and for the divertor visible imaging spectroscopy, designed for the new tokamak DTT (Divertor Tokamak Test), is presented. To deal with the geometrical constraints of DTT and to minimize the diagnostics volume inside the access port, an integrated and compact solution hosting the two systems has been proposed. The Z eff radial profile will be evaluated from the Bremsstrahlung radiation measurement in the visible spectral range, acquiring light along ten Lines of Sight (LoS) in the upper part of the poloidal plane. The plasma emission will be focused on optical fibers, which will carry it to the spectroscopy laboratory. A second equipment, with a single toroidal LoS crossing the plasma centre and laying on the equatorial plane, will measure the average Z eff on a longer path, minimizing the incidental continuum spectrum contaminations by lines/bands emitted from the plasma edge. The divertor imaging system is designed to measure impurity and main gas influxes, to monitor the plasma position and kinetics of impurities, and to follow the plasma detachment evolution. The project aims at obtaining the maximum coverage of the divertor region. The collected light can be shared among different spectrometers and interferential filter devices placed outside the torus hall to easily change their setup. The system is composed of two telescopes, an upper and a lower one, allowing both a perpendicular and a tangential view of the DTT divertor region. This diagnostic offers a unique and compact solution designed to cope the demanding constraints of this next-generation tokamak fusion devices, integrating essential tools for wide-ranging impurity characterization and versatile investigation of divertor physics.

Ultra‐broadband sound absorption characteristics in underwater ultra‐thin metamaterial with three layer bubbles

AbstractThe interest of this article is to obtain the underwater broadband sound absorption characteristics by filling three layers of bubbles in Polydimethylsiloxane polymer (PDMS). In this underwater ultra‐thin metamaterial, three‐layer bubbles are arranged from small to large with the same radius center. The finite element analysis (FEA) method and transfer matrix (TM) method have good consistency in calculating the sound absorption coefficient of this metamaterial. The results reveals that sub‐wavelength metamaterial properties can be achieved below 6.4 MHz. Bubble coupling critical viscosity, waning coupling between layers, waveform transformation, and increasing scattering (reflection) waves all affect broadband sound absorption characteristics. The position and size of three bubbles are discussed, and design summary could be potentially in underwater ultrasound filter devices and medical ultrasound field.

Leukocyte filtration and leukocyte modulation therapy during extracorporeal cardiopulmonary resuscitation in a porcine model of prolonged cardiac arrest

Extracorporeal cardiopulmonary resuscitation (ECPR) is emerging as a feasible and effective rescue strategy for prolonged cardiac arrest (CA). However, prolonged total body ischemia and reperfusion can cause microvascular occlusion that prevents organ reperfusion and recovery of function. One hypothesized mechanism of microvascular “no-reflow” is leukocyte adhesion and formation of neutrophil extracellular traps. In this study we tested the hypothesis that a leukocyte filter (LF) or leukocyte modulation device (L-MOD) could reduce NETosis and improve recovery of heart and brain function in a swine model of prolonged cardiac arrest treated with ECPR. Thirty-six swine (45.5 ± 2.5 kg, evenly distributed sex) underwent 8 min of untreated ventricular fibrillation CA followed by 30 min of mechanical CPR with subsequent 8 h of ECPR. Two females were later excluded from analysis due to CPR complications. Swine were randomized to standard care (Control group), LF, or L-MOD at the onset of CPR. NET formation was quantified by serum dsDNA and citrullinated histone as well as immunofluorescence staining of the heart and brain for citrullinated histone in the microvasculature. Primary outcomes included recovery of cardiac function based on cardiac resuscitability score (CRS) and recovery of neurologic function based on the somatosensory evoked potential (SSEP) N20 cortical response. In this model of prolonged CA treated with ECPR we observed significant increases in serum biomarkers of NETosis and immunohistochemical evidence of microvascular NET formation in the heart and brain that were not reduced by LF or L-MOD therapy. Correspondingly, there were no significant differences in CRS and SSEP recovery between Control, LF, and L-MOD groups 8 h after ECPR onset (CRS = 3.1 ± 2.7, 3.7 ± 2.6, and 2.6 ± 2.6 respectively; p = 0.606; and SSEP = 27.9 ± 13.0%, 36.7 ± 10.5%, and 31.2 ± 9.8% respectively, p = 0.194). In this model of prolonged CA treated with ECPR, the use of LF or L-MOD therapy during ECPR did not reduce microvascular NETosis or improve recovery of myocardial or brain function. The causal relationship between microvascular NETosis, no-reflow, and recovery of organ function after prolonged cardiac arrest treated with ECPR requires further investigation.

Combining descriptive and predictive modeling to systematically design depth filtration-based harvest processes for biologics.

Advances in upstream production of biologics-particularly intensified fed-batch processes beyond 10% cell solids-have severely strained harvest operations, especially depth filtration. Bioreactors containing high amounts of cell debris (more than 40% particles <10 µm in diameter) are increasingly common and drive the need for more robust depth filtration processes, while accelerated timelines emphasize the need for predictive tools to accelerate development. Both needs are constrained by the current limited mechanistic understanding of the harvest filter-feedstream system. Historically, process development relied on screening scale-down depth filter devices and conditions to define throughput before fouling, indicated by increasing differential pressure and/or particle breakthrough (measured via turbidity). This approach is straightforward, but resource-intensive, and its results are inherently limited by the variability of the feedstream. Semi-empirical models have been developed from first principles to describe various mechanisms of filter fouling, that is, pore constriction, pore blocking, and/or surface deposit. Fitting these models to experimental data can assist in identifying the dominant fouling mechanism. Still, this approach sees limited application to guide process development, as it is descriptive, not predictive. To address this gap, we developed a hybrid modeling approach. Leveraging historical bench scale filtration process data, we built a partial least squares regression model to predict particle breakthrough from filter and feedstream attributes, and leveraged the model to demonstrate prediction of filter performance a priori. The fouling models are used to interpret and provide physical meaning to these computational models. This hybrid approach-combining the mechanistic insights of fouling models and the predictive capability of computational models-was used to establish a robust platform strategy for depth filtration of Chinese hamster ovary cell cultures. As new data continues to teach the computational models, in silico tools will become an essential part of harvest process development by enabling prospective experimental design, reducing total experimental load, and accelerating development under strict timelines.

Can a low prime volume arterial filter be used as an alternative for a venous bubble trap in minimal extracorporeal circulation? An in vitro investigation.

During cardiac surgery the use of a minimal extracorporeal circulation (MiECC) system may reduce the adverse effects for the patient. This is probably caused by reduced inflammation and hemodilution. For the use of a MiECC circuit, a venous bubble trap (VBT) is warranted for safety reasons. The aim of this study was to assess if an arterial filter with a small prime volume has the same (or better) air removal capacities as a VBT in a MiECC circuit and subsequentially may be used as an alternative. In an in vitro study, air removal properties were compared between the arterial filter and three VBT's on the market, VBT160 (Getinge), VBT 8 (LivaNova and VARD (Medtronic). In a MiECC circuit, the filter devices were placed in a venous position and challenged with massive and micro air. Gaseous microemboli (GME) were measured with a bubble counter proximal and distal of the VBT device. More than 99.9 % of the air was removed after a bolus air challenge by all VBT's. Both the VARD and the AF100 showed better GME removal properties (not significant for the AF100) compared to the other devices. All filters showed GME generation after a challenge with massive air. Compared to the other filters, only the VARD showed no passing of larger bubbles when a volume of 50mL of air was present in the filter. The AF100 seems to be a safe and low prime alternative for use in a MiECC system as a venous air trap. A word of caution, placement of the AF100 arterial filter in the venous line is off label use.

Performance comparison of different filters based on fibre optic lighting systems and evaluation of architectural lighting effects

Plastic optical fiber lighting is a feasible green lighting method for buildings. This study first derives a mathematical model for the focused light energy absorbed by optical fibers. Based on the variable relationships in the mathematical model, the cooling mechanism of plastic optical fibers was obtained. Secondly, a dual-axis automatic sun-tracking concentrating lighting equipment capable of carrying nine Fresnel lenses was designed. The equipment was used to compare the filtering and cooling effects of two types of filter devices: infrared filters and heat-insulating film. The cooling and lighting effects of these two types of filter devices were also evaluated. Subsequently, the impact of fiber loops on lighting was discussed. Finally, the b2 and b3 modules of the dual-axis automatic sun-tracking concentrating lighting equipment were applied in dark stairwells. The results indicate that the temperature of optical fibers can be reduced by using filtering devices and enhancing heat radiation and convection on the surface of optical fibers. Infrared filters exhibit better cooling and lighting effects than heat-insulating film. Looping the fiber cable reduces the effect of fiber lighting, and the higher the number of loops, the higher the loss of fiber lighting. The dual-axis automatic sun-tracking concentrating lighting equipment increased the illuminance value in the stairwells to over 50 lux, showing great application potential in architectural lighting.

Contemporary Management of Pulmonary Embolism: Review of the Inferior Vena Cava filter and Other Endovascular Devices

AbstractInferior vena cava (IVC) filters and endovascular devices are used to mitigate the risk of pulmonary embolism in patients presenting with lower extremity venous thromboembolism in whom long-term anticoagulation is not a good option. However, the efficacy and benefit of these devices remain uncertain, and controversies exist. This review focuses on the current use of IVC filters and other endovascular therapies in clinical practice. The indications, risks, and benefits are discussed based on current data. Further research and randomized controlled trials are needed to characterize the patient population that would benefit most from these interventional therapies.

Virus adsorbent systems based on Amazon holocellulose and nanomaterials.

The environment preservation has been an important motivation to find alternative, functional, and biodegradable materials to replace polluting petrochemicals. The production of nonbiodegradable face masks increased the concentration of microplastics in the environment, highlighting the need for sustainable alternatives, such as the use of local by-products to create efficient and eco-friendly filtering materials. Furthermore, the use of smart materials can reduce the risk of contagion and virus transmission, especially in the face of possible mutations. The development of novel materials is necessary to ensure less risk of contagion and virus transmission, as well as to preserve the environment. Taking these factors into account, 16 systems were developed with different combinations of precursor materials (holocellulose, polyaniline [ES-PANI], graphene oxide [GO], silver nanoparticles [AgNPs], and activated carbon [AC]). Adsorption tests of the spike protein showed that the systems containing GO and AC were the most efficient in the adsorption process. Similarly, plate tests conducted using the VSV-IN strain cultured in HepG2 cells showed that the system containing all phases showed the greatest reduction in viral titer method. In agreement, the biocompatibility tests showed that the compounds extracted from the systems showed low cytotoxicity or no significant cytotoxic effect in human fibroblasts. As a result, the adsorption tests of the spike protein, viral titration, and biocompatibility tests showed that systems labeled as I and J were the most efficient. In this context, the present research has significantly contributed to the technological development of antiviral systems, with improved properties and increased adsorption efficiency, reducing the viral titer and contributing efficiently to public health. In this way, these alternative materials could be employed in sensors and devices for filtering and sanitization, thus assisting in mitigating the transmission of viruses and bacteria. RESEARCH HIGHLIGHTS: Sixteen virus adsorbent systems were developed with different combinations of precursor materials (holocellulose, polyaniline (ES-PANI), graphene oxide (GO), silver nanoparticles (AgNPs), and activated carbon (AC)). The system that included all of the nanocomposites holocellulose, PANI, GO, AgNPs, and AC showed the greatest reduction in viral titration. The biocompatibility tests revealed that all systems caused only mild or moderate cytotoxicity toward human fibroblasts.

Options for the structure of an autonomous electric power system with a battery of hydrogen fuel cells

Background. Recently, interest in the problem of reducing the emissions of hydrocarbon fuel combustion products into the atmosphere and the use of alternative and renewable energy sources has sharply increased. This problem is relevant to both stationary and transport energy. One of the ways to reduce the harmful impact of primary energy sources in autonomous transport power plants on the environment is their hybridization, i.e., use, along with traditional energy sources (turbogenerators and diesel generators), of hydrogen sources of electricity (fuel cell batteries).&#x0D; Aim. This study presents a justification of the optimal variant of the structure of an autonomous electric power system with a combined power plant based on hydrogen sources of electricity.&#x0D; Materials and Methods. To achieve this goal, a comparative analysis of the parameters and characteristics of the power system elements was performed, as well as a method for modeling processes in the power system under study using the MATLAB Simulink package. Two options for the structure of an autonomous electric power system are being considered, namely, a common AC and DC bus. An analysis of the parameters and characteristics of these options was performed for three typical operating modes, namely, turning on a static load, direct starting of an asynchronous motor with a load on the shaft, and transferring consumers from power from a diesel generator to power from a battery of hydrogen fuel cells.&#x0D; Results. In all considered modes, the VTE battery is characterized by a rapid response to load changes and stable efficiency. The nature of transient processes is aperiodic or low oscillatory, rapidly decaying. In terms of the number of semiconductor converters, filtering devices, and their total power, the structure of an autonomous power system with a common AC bus is more preferable.

Surface-enhanced Raman spectroscopy of the filtrate portions of the blood serum samples of breast cancer patients obtained by using 30 kDa filtration device

Raman spectroscopy is reliable tool for analyzing and exploring early disease diagnosis related to body fluids, such as blood serum, which contain low molecular weight fraction (LMWF) and high molecular weight fraction (HMWF) proteins. The disease biomarkers consist of LMWF which are dominated by HMWF hence their analysis is difficult. In this study, in order to overcome this issue, centrifugal filter devices of 30 kDa were used to obtain filtrate and residue portions obtained from whole blood serum samples of control and breast cancer diagnosed patients. The filtrate portions obtained in this way are expected to contain the marker proteins of breast cancer of the size below this filter size. These may include prolactin, Microphage migration inhabitation factor (MIF), γ-Synuclein, BCSG1, Leptin, MUC1, RS/DJ-1 present in the centrifuged blood serum (filtrate portions) which are then analyzed by the SERS technique to recognize the SERS spectral characteristics associated with the progression of breast cancer in the samples of different stages as compared to the healthy ones. The key intention of this study is to achieve early-stage breast cancer diagnosis through the utilization of Surface Enhanced Raman Spectroscopy (SERS) after the centrifugation of healthy and breast cancer serum samples with Amicon ultra-filter devices of 30 kDa. The silver nanoparticles with high plasmon resonance are used as a substrate for SERS analysis. Principal Component Analysis (PCA) and Partial Least Discriminant Analysis (PLS-DA) models are utilized as spectral classification tools to assess and predict rapid, reliable, and non-destructive SERS-based analysis. Notably, they were particularly effective in distinguishing between different SERS spectral groups of the cancerous and non-cancerous samples. By comparing all these spectral data sets to each other PLSDA shows the 79 % accuracy, 76 % specificity, and 81 % sensitivity in samples with AUC value of AUC = 0.774 SERS has proven to be a valuable technique for the rapid identification of the SERS spectral features of blood serum and its filtrate fractions from both healthy individuals and those with breast cancer, aiding in disease diagnosis.