Film Surface Research Articles

The Influence of Annealing on the Compositional and Crystallographic Properties of Sputtered Li–Al–O Thin Films

Li–Al–O materials are interesting for several applications. Herein, a Li–Al–O thin‐film materials library, deposited by inert magnetron sputtering and postdeposition annealing in O2 atmosphere, is used to study the effects of different annealing temperatures (300–850 °C) and durations (1 min to 7 h) on crystallinity and composition of the films. X‐ray photoelectron spectroscopy depth profiling reveals inhomogeneous compositional depth profiles of conventionally annealed films (300–650 °C, 3–7 h) with increased Li contents toward the film surface and increased Al contents toward the film–substrate interface, as confirmed by a combination of Rutherford backscattering spectrometry and deuteron‐induced nuclear reaction analysis. The minimum temperature for the formation of crystalline LiAlO2 in the otherwise amorphous films is 550 °C. The undesired inhomogeneous depth profiles are transformed into homogeneous ones by rapid thermal annealing (750–850 °C, 1–10 min), while simultaneously causing the formation of crystalline LiAlO2. Therefore, rapid thermal annealing is shown to be more suitable than conventional annealing for the thermal processing of Li–Al–O thin films. Moreover, this conclusion is expected to have broader relevance beyond Li–Al–O materials, as it is likely to apply to other Li metal oxides, of which there are many technologically relevant ones.

Significant improvement in sensitivity of an anomalous Nernst heat flux sensor by composite structure

Heat flux sensors (HFS) have attracted significant interest for their potential in managing waste heat efficiently. A recently proposed HFS, which works on the basis of the anomalous Nernst effect (ANE), offers several advantages in its simple structure leading to easy fabrication, low cost, and reduced thermal resistance. However, enhancing sensitivity through traditional material selection is now challenging due to a small number of materials satisfying the required coexistence of a large transverse thermopower and low thermal conductivity. In this study, by utilizing composite structures and optimizing the device geometry, we have achieved a substantial improvement in the sensitivity of an ANE-based HFS. We developed composite structures comprised of a plastic substrate with an uneven surface and three-dimensional (3D) uneven TbCo films, fabricated using nanoimprint techniques and sputtering. This approach resulted in a sensitivity that is approximately four times greater than that observed in previous studies. Importantly, this method is independent of the material properties and can significantly enhance the sensitivity. Our findings could lead to the development of highly sensitive HFS devices and open avenues for the fabrication of 3D devices.

Study on the film-forming properties of Mo–Na ceramic targets

In order to provide sufficient and stable Na+ for the CIGS flexible thin film solar cells, Mo–Na ceramic targets were prepared by the plasma-assisted cold sintering process (CSPS). And the film-forming properties of the Mo–Na targets were studied. The Mo–Na targets were prepared with MoO3 as precursor. The Mo–Na targets were successfully prepared with uniformity, compactness and high relative density (98.19 %). Then, the Mo–Na monolayer films were prepared by radio frequency (RF) magnetron sputtering. The results show that Mo–Na monolayer films are homogeneous and compact. Significantly, abundant Na+ are stored in the Mo–Na monolayer films. To verify the application of Mo–Na targets in the CIGS cells, the sandwich structure (Mo/Mo–Na/Mo) films and co-sputtered films were studied. The results show that the co-sputtered films have sufficient Na+, and show good photoelectric and mechanical properties. In addition, after heat treatment, Na+ can diffuse to the surface of the sandwich films, which can provide sufficient and stable Na+ for CIGS thin film cells.

ZrO2-CeO2/WO3 heterostructure films prepared by magnetron sputtering for humidity-tolerant triethylamine sensing

Up to now, the development of gas sensors based on metal oxide semiconductors (MOSs) that can detect triethylamine (TEA) under high humidity conditions remains a significant challenge. In this study, we present the ZrO2-CeO2/WO3 (ZCW) heterostructure films for TEA detection under high relative humidity, which were prepared by co-sputtering ZrO2 and CeO2 onto the surface of a WO3 film using the radio frequency magnetron sputtering method. The gas sensors based on the ZCW heterostructure films exhibited outstanding TEA-sensing performance, including high response (18.56–20 ppm), rapid response/recovery rate (1/5 s), excellent selectivity, wide detection range (0.5–500 ppm), outstanding reproducibility and stability, and ideal anti-humidity ability. The excellent TEA-sensing properties of the ZCW heterostructure films should be mainly attributed to their unique surface microstructure, abundant oxygen vacancies, and the formation of heterostructures between ZrO2, CeO2, and WO3. Compared to the WO3 film, both the CeO2/WO3 and ZrO2-CeO2/WO3 films demonstrated highly-enhanced humidity-tolerant performance, which should result from the redox reactions between the Ce3+ and Ce4+ ions. This study provides a general method for preparing the MOSs-based TEA sensors that could work under high humidity condition.

Discriminative performance of ocular surface staining and lid wiper epitheliopathy in dry eye disease: an investigator-masked, prospective registry-based, diagnostic accuracy study

To evaluate the diagnostic performance of corneal and conjunctival staining, and lid wiper epitheliopathy (LWE) in detecting dry eye disease, as defined by the global consensus Tear Film and Ocular Surface Society Dry Eye Workshop II (TFOS DEWS II) criteria. A total of 2,066 community residents (1285 females; mean±SD age, 40 ± 19 years) were recruited in an investigator-masked, prospective registry-based, diagnostic accuracy study. Dry eye symptomology and ocular surface parameters were assessed in a single clinical session. The Sjögren's International Collaborative Clinical Alliance (SICCA) corneal and conjunctival staining scoring and Korb lid wiper epitheliopathy (LWE) grading were evaluated by an independent masked assessor. Overall, 807 (39%) participants fulfilled the TFOS DEWS II criteria for dry eye disease, of which 178 (9%) participants were classified as moderate-to-severe disease. The discriminative abilities of superior and inferior LWE (C-statistics, 0.724 and 0.712, respectively) were greater than corneal and conjunctival staining (C-statistics, 0.573 and 0.627, respectively). The Youden-optimal diagnostic cut-offs for the SICCA corneal and conjunctival staining scores were both ≥1, and the optimal thresholds for the Korb superior and inferior LWE grades were both ≥1. LWE was more commonly detected in both mild-to-moderate and moderate-to-severe dry eye disease, and demonstrated more consistent correlation with other ocular surface parameters across a broader range of disease severity. LWE demonstrates superior diagnostic performance relative to corneal and conjunctival staining. These findings would support the routine incorporation of LWE evaluation as part of the diagnostic workup of dry eye disease.

Modelling of evaporative falling-film heat transfer over a horizontal tube

This article focuses on evaporative falling film heat transfer through numerical simulations. A two-dimensional symmetric liquid film flowing outside a single horizontal tube was simulated using the open-source CFD software OpenFOAM. The Tanasawa model was employed to consider mass transfer at the liquid–vapour interface, and the isoAdvector VOF method was used for interface tracking. The simulations explored the impact of film flow rate, tube surface heat flux, and tube diameter on the liquid film thickness and surface heat transfer coefficient. Additionally, the critical heat flux and operational limits were considered. The results demonstrate the accurate reproduction of evaporative falling film heat transfer performance by the present model. The film thickness exhibits a similar profile to adiabatic and sensible falling film heat transfer but provides smaller values. Similarly, the evaporative heat transfer coefficient exhibits significantly higher values and a gentle peripheral variation. The influence of heat flux on evaporative falling film heat transfer is contingent on the film flow rate; it can either enhance or weaken the process. Notably, a larger tube diameter negatively affects heat transfer, suppressing the impact of heat flux, and also increases the risk of liquid film dryout. For a given film flow rate, the average heat transfer coefficient increases initially, reaches a maximum value, and then decreases as the wall heat flux is increased. The peak heat flux, termed critical heat flux, increases with film flow rate but decreases with tube diameter. An operational limit exists where the heat flux is lower than the critical heat flux and the film flow rate is higher than the critical film flow rate; under these conditions, evaporative falling film heat transfer operates in a fully wetting status.

A novel Se-diffused selenization strategy to suppress bulk and interfacial defects in Sb2Se3 thin film solar cell

In recent years, vacuum-based deposition of antimony selenide (Sb2Se3) thin films has garnered significant attention owing to its easy and impurity-free fabrication, along with exceptional power conversion efficiency (PCE). However, the necessary post-selenization process comes with a shortcoming of instigating buried Sb2Se3/molybdenum (Mo) back-contact interface defects. This study introduces a novel Se-diffusion post-selenization technique to precisely regulate the selenium reaction atmosphere, preventing void formation on the Sb2Se3 thin film surface and maintaining film quality for enhanced device efficiency. An optimized selenization condition with a precise Se precursor film thickness led to obtaining highly crystalline, preferentially (hk1) oriented, and large-grained Sb2Se3 films. Furthermore, a meticulous Se diffusion in Sb2Se3 film reduced the inevitable MoSe2 layer thickness at the Mo surface, thereby enhancing the quality of the back contact interface. The Sb2Se3 solar cell that was selenized to optimal level showed significant enhancements, raising the fill factor from 40.06 % to 45.12 % and improving the device efficiency from 2.89 % to 3.57 %. Our newly developed selenization strategy establishes a successful approach to regulate the Sb2Se3 film quality by addressing a crucial challenge in improving the efficiency of antimony chalcogenide solar cells.

Aloe vera Miller extract as a plasticizer agent to polymeric films: A structural and functional component

The pharmaceutical and cosmetic industries have found natural polysaccharides-based polymeric films helpful for the topical application of drugs. Plasticizers, such as glycerol, are added to achieve films' desired mechanical, elastic, and flexible properties. Aloe vera Miller mucilage is known for healing burns and wounds, relieving pain, and moisturizing, suggesting its great potential for managing multiple topical issues. Herein, we exploited the plasticizing potentialities of A. vera extract when combined with gellan or carrageenan polysaccharides to produce films. The extract of A. vera mucilage was prepared in propane-1,2-diol, and its composition was comparatively evaluated with a commercial extract using a chemometric method. Next, it was added to the films obtained using the solvent-casting method. The formulations were investigated regarding the mechanical properties, swelling, water loss, porosity, water vapor transmission rate, degree of occlusion, adhesion force, and antioxidant action. Fourier transform infrared spectroscopy assessed the films stability and homogeneity with an exploratory chemometric method to classify the samples. The results showed that carrageenan and gellan polysaccharides-based polymeric films have great potential for including A. vera extract. The extract acts as a plasticizer and promotes desirable properties and swelling behavior for films intending wound management. Comparatively, films prepared with glycerol beyond the extract presented higher thickness, lower swelling, and higher occlusion and antioxidant activity. Despite this, glycerol seems to negatively influence the homogeneity of the extract on the film surface. In addition, regarding polysaccharides, carrageenan showed higher bioadhesion. Therefore, the films produced exhibited favorable properties, highlighting their potential for further research regarding wound management.

Dry eye disease in systemic lupus erythematosus: a cross sectional study.

To explore ocular surface manifestations of dry eye disease (DED) and its influencing factors in systemic lupus erythematosus (SLE) patients. Ophthalmological examinations were conducted in SLE patients (n=43) and controls (n=41), including Ocular Surface Disease Index (OSDI), objective scatter index (OSI), tear meniscus height (TMH), lipid layer thickness (LLT), non-invasive Keratograph tear breakup time (NIKBUT), corneal fluorescein score (CFS), Schirmer I test. DED was diagnosed according to the Tear Film and Ocular Surface Society Dry Eye Workshop II Criteria. SLE patients were further divided into DED group and non-DED group, the disease activity, clinical manifestations and laboratory investigations were compared between the two groups. The disease activity was evaluated by Systemic Lupus Erythematosus Disease Activity Index 2000 (SLEDAI-2K). Receiver operative characteristic (ROC) curve and multiple-factor binary logistic regression were performed. SLE patients showed higher OSDI [9.1 (2.8-15.9) vs 6.3 (2.2-7.5), P=0.035], higher OSI [1.67 (1.09-2.60) vs 0.96 (0.87-1.60), P=0.001], higher CFS [1 (0-2) vs 0 (0-1), P=0.001], lower LLT [65 (42-100) vs 100 (79.5-100), P=0.010], and lower NIKBUT [8.03 (4.02-9.73) vs 9.67 (5.26-12.71), P=0.030] than controls. The 32.6% of SLE patients had DED, which was higher than 12.2% of healthy controls. DED group showed higher SLEDAI-2K score [9.7±6.1 vs 5.4±3.4, P=0.025], higher anti-cardiolipin antibody (ACL) [8.7 (3.5-13.2) vs 3.6 (2.0-6.9), P=0.035], and higher proportion of patients with cutaneous eruption [42.9% vs 6.9%, P=0.015] than non-DED group. According to multiple-factor binary logistic regression analysis, the SLEDAI-2K score (OR=1.194, P=0.041) and cutaneous eruption (OR=7.094, P=0.045) could be consider as risk factors for DED in SLE patients. The ROC curve of the combined factors including age, disease duration, SLEDAI-2K score, ACL, and cutaneous eruption was analyzed, with a sensitivity of 0.786, a specificity of 0.793, and an area under curve of 0.820. Ocular surface affection is frequent in SLE patients, and patients with high disease activity and cutaneous eruption show increased risk of DED.

Enlightenment of Deionized‐Water Bathing IGZO TFTs

AbstractAt present, amorphous indium–gallium–zinc oxide (IGZO) semiconductor has become the most commonly used semiconductor material and is widely used in flat panel displays and various sensors, but its performance is greatly affected by environmental factors, especially water. This study investigates the instability of IGZO thin‐film transistors (TFTs) soaked in deionized water. After 24 h bathing, the field‐effect mobility and threshold voltage change a little, but the subthreshold swing, positive bias stress and negative bias stress stability undergo clear degradation. Through comprehensive examination of the changes in the chemical composition, surface morphology and thickness of the IGZO films, it's found that IGZO experiences selective etching by deionized water, and consequently the film surface becomes rough and rich of In and oxygen vacancies, which can explain the variations on device performance well. In addition to the bathing experiment performed on In2O3, Ga2O3, and ZnO TFTs, a schematic image of the reaction between water and IGZO is depicted, showing the preferential loss of Ga and Zn located next to the oxygen vacancy.

Stabilizing Lead Halide Perovskites via an Organometallic Chemical Bridge for Efficient and Stable Photovoltaics.

Defects around the surface and grain boundaries of perovskite films normally cause severe nonradiative recombination and imbalanced charge carrier transport, further limiting both the efficiency and stability of perovskite solar cells (PSCs). To tackle this critical issue, we propose a chemical bridge strategy to reconstruct the interface using organometallic molecules. The commercially available molecule bis(diphenylphosphino)ferrocene (FcP2), with a unique bridge molecular structure, anchors and chelates Pb atoms by forming strong Pb-P bonds and further passivates both surfaces and grain boundaries. Detailed characterization revealed that bridge molecule FcP2 reconstruction can effectively suppress nonradiative recombination, and the electron delocalization properties of the ferrocene core can further achieve more balanced interfacial carrier transport. The resultant N-i-P PSC device outputs close to 25% efficiency together with one of the best reported operational stabilities, maintaining over 95% of the initial efficiency after 1000 h of continuous operation at the maximum power point under 1-sun illumination.

Structuring of the Surface of Thin Carbon Films During Activation by Microsecond Current Pulses

The influence of current activation by electric pulse breakdown on changes in surface morphology and emission characteristics of a field emission cathode made on the basis of carbon films obtained by deposition in a microwave gas discharge plasma was studied. Current activation of these films was carried out by applying voltage pulses of microsecond duration until an electrical breakdown occurred. It is shown that during activation, the morphology of the film surface in the breakdown region changes with the formation of a micro-sized emitting structure, which significantly improves the field emission characteristics of cathodes based on carbon films.

Molecular Layering of an Additive Layer of Silicon Dioxide on Anodized Tantalum and Niobium Oxides

The results of studying the processes of formation of nanolayers of silicon oxide by the method of molecular layering (atomic layer deposition) on the surface of films of tantalum and niobium oxides obtained by electrochemical oxidation of the corresponding metals are presented. A study of the electrical strength of metal-dielectric-metal (MDM) structures based on tantalum and niobium oxides showed that the introduction of an additive dielectric layer (SiO2) can significantly increase the electrical strength of these structures.

Atomic-Level Observation of Potential-Dependent Variations at the Surface of an Oxide Catalyst during Oxygen Evolution Reaction.

Understanding the intricate details of the surface atomic structure and composition of catalysts during the oxygen evolution reaction (OER) is crucial for developing catalysts with high stability in water electrolyzers. While many notable studies highlight surface amorphization and reconstruction, systematic analytical tracing of the catalyst surface as a function of overpotential remains elusive. Heteroepitaxial (001) films of chemically stable and lattice-oxygen-inactive LaCoO3 are thus utilized as a model catalyst to demonstrate a series of atomic-resolution observations of the film surface at different anodic potentials. The first key finding is that atoms at the surface are fairly dynamic even at lower overpotentials. Angstrom-scale atomic displacements within the perovskite framework are identified below a certain potential level. Another noteworthy feature is that amorphization (or paracrystallization) with no long-range order is finally induced at higher overpotentials. In particular, surface analyses consistently support that the oxidation of lattice oxygen is coupled with amorphous phase formation at the high potentials. Theoretical calculations also reveal an upward shift of oxygen 2p states toward the Fermi level, indicating enhanced lattice oxygen activation when atom displacement occurs more extensively. This study emphasizes that the degradation behavior of OER catalysts can distinctively vary depending on the overpotential level.

Engineering of Silane–Pyrrolidone Nano/Microparticles and Anti-Fogging Thin Coatings

Polyvinylpyrrolidone (PVP) exhibits remarkable qualities; owing to the strong affinity for water of its pyrrolidone group, which enhances compatibility with aqueous systems, it is effective for stabilizing, binding, or carrying food, drugs, and cosmetics. However, coating the surface of polymeric films with PVP is not practical, as the coatings dissolve easily in water and ethanol. Poly(silane–pyrrolidone) nano/microparticles were prepared by combining addition polymerization of methacryloxypropyltriethoxysilane and N-vinylpyrrolidone, followed by step-growth Stöber polymerization of the formed silane–pyrrolidone monomer. The silane–pyrrolidone monomeric solution was spread on oxidized polyethylene films with a Mayer rod and polymerized to form siloxane (Si-O-Si) self-cross-linked durable anti-fog thin coatings with pyrrolidone groups exposed on the outer surface. The coatings exhibited similar wetting properties to PVP with significantly greater stability. The particles and coatings were characterized by microscopy, contact angle measurements, and spectroscopy, and tested using hot fog. Excellent anti-fogging activity was found.

Investigating the physicochemical, antimicrobial and antioxidant properties of chitosan film containing zero-valent iron nanoparticles and oregano essence.

The problems caused by the pollution of the environment by petroleum polymers in recent years have caused researchers to think of replacing petroleum polymers with biodegradable and natural polymers. The aim of this research was to produce composite film of chitosan (Chit)/zero-valent iron (Fe) nanoparticles/oregano essence (Ess) (Chit/Fe/Ess). Central composite design was used to study physical, morphological, antioxidant and antimicrobial properties of films. The results showed that with the increase of iron nanoparticles and oregano essence, the thickness of the film increased. The moisture, solubility and water vapor permeability of the film decreased with the increase of iron nanoparticles and oregano essence. The results of the mechanical test showed that with the increase of iron nanoparticles and oregano essence, the tensile strength and elongation at break point decreased. Iron nanoparticles and oregano essence increased significantly the antioxidant activity of the film. The results of the antimicrobial activity of the prepared films show that the addition of iron nanoparticles and oregano essence enhanced the antimicrobial activity of the film against Escherichia coli and Staphylococcus aureus. X-ray diffraction analysis showed that iron nanoparticles were physically combined with chitosan polymer. Fourier transform infrared (FTIR) results confirmed the physical presence of iron nanoparticles and oregano essence in the polymer matrix. The results of scanning electron microscopy (SEM) showed that the surface of nanocomposite films is more heterogeneous than chitosan. Iron nanoparticles and oregano essence could delay the thermal decomposition of chitosan and increase the thermal stability of chitosan film.

Mid-Infrared Photoacoustic Stimulation of Neurons through Vibrational Excitation in Polydimethylsiloxane.

Photoacoustic (PA) emitters are emerging ultrasound sources offering high spatial resolution and ease of miniaturization. Thus far, PA emitters rely on electronic transitions of absorbers embedded in an expansion matrix such as polydimethylsiloxane (PDMS). Here, it is shown that mid-infrared vibrational excitation of C─H bonds in a transparent PDMS film can lead to efficient mid-infrared photoacoustic conversion (MIPA). MIPA shows 37.5 times more efficient than the commonly used PA emitters based on carbon nanotubes embedded in PDMS. Successful neural stimulation through MIPA both in a wide field with a size up to a 100µm radius and in single-cell precision is achieved. Owing to the low heat conductivity of PDMS, less than a 0.5°C temperature increase is found on the surface of a PDMS film during successful neural stimulation, suggesting a non-thermal mechanism. MIPA emitters allow repetitive wide-field neural stimulation, opening up opportunities for high-throughput screening of mechano-sensitive ion channels and regulators.

Ni/Graphene Coating for Enhanced Corrosion Resistance of Metal Foam Flow Field in Simulated PEMFC Cathode Environment.

Metal foam flow field suffers serious corrosion issues in proton exchange membrane fuel cells due to its large surface area. Ni and Ni/graphene coatings are prepared under constant and gradient current modes, respectively, to improve the corrosion resistance. The effect of the electrodeposition current mode and the deposition mechanism is studied. Compared with Ni coating, Ni/graphene coating brings low corrosion current density and high coating resistance, effectively enhancing the stability of Ni foam in an acidic environment. Different from Ni coating with a single layer, Ni/graphene deposits have core-shell structure, with graphene coated on the surface of Ni nanoparticles. It is shown that graphene deposits cover the Ni particles during the electrodeposition, which protects nickel particles from agglomeration and forms an inert film on the surface of the porous structure. After an 8 h constant potential test, no significant pitting is observed on the surface of Ni/graphene coating, showing excellent anticorrosion performance. As to the effect of the deposition current mode, it is shown that more composite particles deposit on the upper layer under the gradient current mode, which brings denser protective film and fewer surface defects on the surface. Ni/graphene coating electrodeposited under a gradient current mode between 0 and 10 mA·cm-2 exhibits the lowest corrosion current densities. The values at 50 and 80 °C are only 62.9 and 26.0% of those of uncoated Ni foam, respectively.

Fast fabrication, gas sense characteristics and kinetics of cubic Ti-BIPA-TC-MOF film composite optical waveguides

A cubic Ti-metal-organic framework (MOF) ([Ti2–(TpA)2–H2BIPA]), constructed from a titanium metal centre and a benzo-imidephenanthroline tetracarboxylic acid (H4BIPA–TC) ligand was photo-inductively grown on the surface of a titanium dioxide (TiO2) composite optical waveguide (COWG) substrate and the influence of photo-inductive growth period on the [Ti2–(TpA)2–H2BIPA] film surface morphology, optical properties and gas adsorption/sensing characteristics was investigated. The results showed that [Ti2–(TpA)2–H2BIPA] formed a cubic structure after grew for only 5 min. As an ideal gas adsorbent, it exhibits a specific response to ethylenediamine (EDA) among various benzene, amine and acid gases, due to the intrinsic electron deficiency, rich COOH active sites of the Ti–BIPA–TC–MOF–5 frame and the higher molar refractive indexes or dipoles of EDA than other gases. In the EDA concentration range from 10 ppt to 100 ppm, the Ti–BIPA–TC–MOF–5 film COWG exhibited a rapid, repeatable response. Moreover, the Ti–BIPA–TC–MOF–5 film COWG was relatively stable, within 17 d of EDA detection, the response intensity was almost constant and slightly decreased within 40 d. In a static gas adsorption stage at 283–313 K, the EDA gas adsorption behaviour of the Ti–BIPA–TC–MOF–5 film is consistent with the pseudo-second-order kinetic model.

PREVENTING OF MIGRATION IN FOOD CONTACT POLYVINYL CHLORIDE-BASED STRETCH FILMS WITH POLYLACTIC ACID LAYER

In this study, the effectiveness of biodegradable polylactic acid (PLA) coatings for the prevention of residues migrating through polyvinyl chloride (PVC) films was investigated. PLA films prepared in chloroform at concentrations of 5, 10, 15 and 20 wt% were heat sealed to PVC film surfaces in a hot press (130 °C, 5 min, 5 tons). Physical, mechanical, FTIR and migration analyses were performed on these two-layer films. With PLA coating, the thickness of the films increased, mechanical properties decreased and some changes in color values occurred. It was determined by FTIR that there was no structural change on both surfaces of the films as a result of hot pressing. From the overall migration analysis, no migration was observed in the tests with aqueous food simulants, while migration was detected in fatty food simulants. In the specific migration analysis by GC-MS, di-2-ethylhexyl phthalate (DEHP) migration decreased by 50% with PLA coating. It is concluded that PLA coating of PVC stretch films may be a promising application to reduce migration.