Fibrous Particles Research Articles

The Influence of Fibers from Domestic Laundry Wastewater on the Clogging Process of a Filter

This study presents the impact of the size and shape of particles in laundry wastewater on the clogging process of a porous material. Clogging can be defined as a mechanical limitation of flow through porous media. The process of mechanical clogging was investigated in this study. The research was conducted in laboratory conditions in a filter column filled with glass beads whose diameter corresponded to coarse sand. The results reveal the influence of graywater quality on filter hydraulic conductivity and bed clogging, showing the impact of fiber particles in wastewater (sewage from home laundry) on the clogging process in soil. The results confirm that fiber particles significantly reduce filter permeability, particularly due to the formation of a filter cake. As analyzed in this paper, the distribution of quantitative data on particles of different sizes found in laundry wastewater indicates that they mainly accumulate in the upper layer, where particles with fiber lengths ranging from 0 to 1600 µm can be found. The average length of the fibers decreased with increasing depth. At a depth of approximately 10 cm, fibers with dimensions in the range of 0 to 100 μm were predominantly observed.

Tobacco stalk nanofibrillated cellulose: An eco-friendly binder on fluidized bed granulation

The search for new excipients that provide formulation alternatives over existing ones and that are derived from natural resources has advanced over the years. Emerging from this scenario, an important alternative to traditional excipients is nanofibrillated cellulose (NFC), which is generally obtained from agricultural wastes and is a cellulose-rich material. Most of the time, the nanofibers are presented in aqueous dispersions that form a highly entangled network of fibrous particles that exhibit gel-like behavior. Therefore, the present work aimed to explore the gel-like behavior of NFC from tobacco stalks to evaluate it as a binder in a fluid bed granulation process for further application as a pharmaceutical ingredient. The granulation process was carried out using top spray mode with an inlet air temperature of 80 °C, airflow between 9 and 11 mm3 h−1, and atomizing air pressure of 0.7 bar. Povidone (PVP) was used as a standard binder for comparison purposes. The binder systems were sprayed on the powder blend of theophylline and maltodextrin at a feed rate of 3.05 mL⋅min−1. Granule properties, such as yield, moisture content, morphology, label-free Raman imaging, particle size distribution, drug content, and flow properties, were evaluated. The process using NFC provided granules with excellent drug uniformity, low moisture content (<2 %), high yield (>92 %), and passable flow properties. Their behavior was comparable to that of granules prepared with the classical PVP binder system. Therefore, this study opens a perspective for the reuse of NFC from tobacco stalk, an agricultural waste, as an alternative binder for the granulation process, contributing to environmental sustainability.

Novel food-grade water-in-water emulsion fabricated by amylopectin and tara gum: Property evaluation and stability analysis

To surmount the limitation of the instability of the currently reported water-in-water (W/W) emulsions, novel W/W emulsionss were constructed using amylopectin (AMP) and tara gum (TG) as the phases, and differently shaped ovalbumin (OVA) particles were used as stabilizers to improve the stability of W/W emulsions. Experiments displayed that the conformation of OVA could be changed by heating treatment, thus forming fibrous or spherical OVA particles that had the potential to stabilize TG-in-AMP (TG/AMP) emulsions. The emulsions had the best stability when the pH was 4 and the concentration of OVA particles was 3 %. Moreover, since ovalbumin fibril (OVAF) had better adsorption at the water-water interface than ovalbumin sphere (OVAS), OVAF-stabilized TG/AMP emulsion (OF-TE) had a relatively denser interfacial layer and exhibited more satisfactory ionic stability and physical stability than OVAS-stabilized TG/AMP emulsion (OS-TE). The rheological results demonstrated that OVAF and OVAS had little effect on the viscosity of TG/AMP emulsions. In brief, OVAF was more effective in improving the stability of TG/AMP emulsions than OVAS, and OF-TE did not show phase separation for at least 5 days. This study may be of great significance in improving the stability of food-grade W/W emulsions.

Oleogel formation based on natural insoluble soybean fiber using capillary force: A novel strategy and application

Insoluble dietary fibers can be used as oleogelators to form oleogels via molecular self-assembly following chemical modification. However, the limitations of traditional chemical modifications and oleogel preparation methods significantly restrict their practical application. This study proposed a novel method to directly form edible oleogels using natural soybean insoluble fiber particles as oil-forming agents and water as a secondary fluid via the capillary suspension force between particles. The results showed that when the particle fraction was 15 % and the secondary fluid content was 0.2, a strong capillary suspension force could be formed to maintain the oil holding capacity of oleogels. The sedimentation coefficient analysis showed that adding particles and secondary fluids significantly affected the oleogel stability. The polarity of the oils, as well as the ionic strength and pH of the secondary fluids, influenced the rheological properties of oleogels, which correlated with the interfacial tension between the secondary fluids and oils. Moreover, the stable oleogels showed their potential as excellent solid fat substitutes in the preparation of breads (specific volume = 2.029 ± 0.114 cm3/g, weight loss = 12.2 ± 2.6 %, and hardness = 3.321 ± 0.055 N). This study highlighted that insoluble dietary fiber can form oleogels via capillary suspension, which is a relatively rapid and simple strategy. Additionally, it provided a solid foundation for the comprehensive utilization of soybean processing byproducts and the transformation of traditional food-specific oils and fats.

Enhancing 3D printing performance of O/W emulsions with asparagus fibre

Asparagus fibre recovered from agricultural waste stream can be valorised as a natural ingredient for fibre enrichment in food products. This study investigated the effects of asparagus fibre on the 3D printing performance of oil-in-water (O/W) emulsions as edible inks. Emulsion gels were prepared by either varying the fibre concentration in the aqueous phase or varying the volume fraction of the oil phase. Printability, rheological properties, and microstructure of the samples were systematically evaluated. Our results show increasing fibre concentration (up to 9.9 %w/w) significantly improved 3D printing performance of the inks, which was attributed to their enhanced rheological properties. Interestingly, reducing the oil volume fraction from 72 to 66 %v/v (i.e., fibre concentration was kept at 9.9 %w/w) did not detrimentally influence the 3D printing quality. Microstructural analysis of the emulsions revealed that increasing fibre concentration led to smaller size and different surface morphology of the oil droplets. Fibre particles in the aqueous phase may hinder oil droplet movement, stabilizing emulsions during 3D printing. Our findings give new insights into the development of edible 3D-printed food products via fibre enrichment and oil reduction.

Particle size of straw and gelation of pectin influence gastric mixing and emptying in pigs

Physicochemical properties of fibres can strongly impact gastric processes such as emptying and sieving. This study evaluated the influence of particle size of insoluble fibres, and gelation of soluble fibres when added to insoluble fibres, on gastric emptying of digesta phases from the proximal and distal stomach of pigs. Twenty-four boars (51.6 ± 4.90 kg) were assigned to one of four diets, containing either 150 g/kg coarse or finely milled wheat straw (median particle area of 5.4 vs. 0.3 mm2), or 270 g/kg wheat bran without or with the addition of 100 g/kg low-methylated pectin. Tracers were used to quantify the mean retention time (MRT) of digesta liquids (Co-EDTA), fine solids (TiO2), and fibrous particles (Chromium-mordanted fibres). For all diets, digesta pH was lower in the distal stomach than in the proximal stomach (-1.1 to 2.1 units; P < 0.05). In the proximal stomach, particle size reduction of straw tended to decrease digesta pH (-0.8 units; P = 0.072), reduced the MRT of fine solids (-117 min; P = 0.009) and the separation between fine solids and liquids (-88 min; P = 0.030). When particle size of straw was reduced, the MRT of liquids was no longer greater in the proximal stomach compared with the distal stomach (P > 0.10), while in both regions, the MRT of fibrous particles (-213 to 238 min; P < 0.05) and the difference between fibrous particles and fine solids were reduced (-96 to 181 min; P < 0.05). Accordingly, sieving of nutrients, such as starch and non-starch polysaccharides (NSP) was reduced. In the proximal stomach, the greater water holding capacity (WHC) and resistance to deformation conferred by the addition of pectin decreased the MRT of fine solids (-138 min; P = 0.003), and fibrous particles (-227 min; P < 0.001), reducing the difference between fine solids and liquids (-148 min; P < 0.001), and between fibrous particles and fine solids (-89 min; P < 0.001). In the distal stomach, pectin addition reduced the MRT of fibrous particles (-203 min; P = 0.007), and the difference between fibrous particles and fine solids (-154 min; P < 0.001). Concomitantly, sieving of nutrients across stomach regions was reduced. In conclusion, particle size reduction of straw and pectin addition accelerated the emptying of fine and coarse solids, and reduced sieving of digesta phases and nutrients in the proximal and distal stomach of pigs.

Fabrication of PVC-based electromagnetic interference shielding composite film by positively charged SMA enhancing the dispersibility of carbon nanomaterial

To address the weak binding force and poor dispersion stability of carbon (C) nanoparticles in current non-covalent modification methods, we employed organic amine-grafted styrene maleic anhydride copolymers (SMA-N) to modify C nanoparticles (C@SMA-N) through π–π conjugation and positive charge interactions. The obtained C@SMA-N has excellent dispersion in N, N-dimethylacetamide (DMAc), which is attributed to the enhanced steric hindrance and electrostatic repulsion from the grafted organic amine chains. To study the impact of surface modification on the electromagnetic interference shielding effectiveness (EMI SE), C@SMA-N was used as a conductive filler in polyvinyl chloride (PVC) composite films, which exhibits a higher EMI SE performance than pristine C nanoparticles. Particularly, the obtained C@SMA-N using polyether amine (PEA) (C@SMA-PEA) exhibits a better EMI SE performance. By optimizing the SMA-PEA grafting parameters, the PVC/C@SMA-PEA composite films transition from insulators to conductors at a C@SMA-PEA content of 0.3 wt%. To achieve a higher EMI SE performance, the filler content, mixed filler composition, and film thickness were optimized. The results indicate that with a total filler content of 20 wt% and a mixed filler comprising fibrous form carbon nanotubes (CNT) and particles form carbon black (CB) in a 10:1 mass ratio (CB@SMA-PEA to CNT@SMA-PEA), the composite film has a thickness of 0.08 mm and an EMI SE value of 20.2 dB. Increasing the thickness to 0.2 mm enhances the EMI SE value to 31.5 dB. These findings indicate that thinner films have a higher EMI SE performance and promising application prospects in the field of electromagnetic shielding.

Characterization of Discharge Associated With Fiber Particle Aggregation in Oil Streams Under High-Voltage Direct Current Field

Characterization of Discharge Associated With Fiber Particle Aggregation in Oil Streams Under High-Voltage Direct Current Field

Analysis of technologies of disposal and use fibrous paper skopje

The article examines the current state and trends in the development of waste management technologies in the pulp and paper industry, with the aim of analyzing the reasons that hinder, and sometimes make impossible, the effective utilization of fibrous waste paper to obtain environmentally safe materials and raw products. The production of paper products is one of the most capital-intensive and energy-intensive industries, second only to the metallurgical and chemical industries, with a correspondingly large amount of waste and a negative impact on the environment. The technological processes of scum formation as a result of waste paper recycling and paper production wastewater treatment are considered and analyzed. Skopje is the final waste of the pulp and paper industry, which is formed at various stages of the paper and cardboard manufacturing process, therefore it is deposited in landfills. Multiton volumes of skopje require significant areas for its storage. Despite the low IV hazard class, this leads to serious environmental problems, as the leachate from the skopje landfill pollutes surface and ground water. Technologies of possible disposal and reuse of skopje, known in domestic and foreign literature, are described and analyzed. The technology of reusing scoop is determined by its relatively environmentally safe physicochemical composition. The indicated fibrous, mineral, extractive constituents and lignin determine the possibility of reusing skopje, mainly for the construction industry. The perspective of the complex use of multi-tonnage waste – slag, sludge, ash and slag of thermal power plants as plasticizers, fillers, binders and binding components in the production of building structural and heat-insulating materials is named. Technologies for using scapula as a filler in the production of building materials require a high content of inorganic compounds and a minimum amount of organic compounds. A high content of fibrous particles and a low content of mineral substances is necessary when using scapula in the production of composite wood composite materials. The specified technological limitations ensure only small amounts of skopje use in the production of building materials. The effectiveness of using skopje as an additive to the asphalt mixture for road construction and production of fuel materials is determined by the economic costs of transportation and dewatering. It is noted that the high humidity, ash content and low calorific value of scum are the main reason for the lack of effective technologies for its utilization. The solution to the problem is the use of low-energy technologies through the direct use of osprey as a component of the soil mixture for biological reclamation of man-made landscapes. The article substantiates an environmentally safe and socially favourable option for using a soil substrate based on osprey. It is emphasised that the humidity and organic viscosity of the plant origin of osprey form the agrotechnical properties of soil substrates of prolonged action, which ensure optimal technological efficiency of phytomelioration of degraded lands. The reclaimed areas will reduce greenhouse gas emissions from the soil, prevent wind and water erosion, and ensure the environmental safety of natural and man-made ecosystems.

Evaluation of the OpTest Fiber Quality Analyzer for Quantifying Cotton and Rayon Microfibers

Microfibers are small fiber particles that separate from larger textiles through wear abrasion or home laundering. Pervasive accumulation of synthetic microfibers in the environment is motivating efforts to quantify them, and to gain a better understanding of the factors that lead to their release from garments. Automated imaging systems have been previously employed for the quantification of synthetic and natural microfibers. In the current study, a rayon standard and microfibers sourced from scoured cotton HVI calibration standards were examined with the Fiber Quality Analyzer-360 (FQA) automated imaging system. Mechanically stirred suspensions of six cotton microfiber standards showed significantly lower fiber counts than those obtained with a rayon standard. Probe sonication of the sample suspensions significantly increased observed fiber counts for the cotton standard samples, by 105% on average. Mean length determinations decreased by, on average, 5% for the sonicated samples, an indication that count increases were not due to sample fragmentation. No significant change was observed for the fiber counts or length measurements of the sonicated rayon samples. The sonicated cotton samples showed an average of 95% detection by the FQA. These results highlight the importance of proper microfiber suspension for accurate detection and quantification using the FQA system.

Investigating the deposition of fibrous zeolite particles on leaf surfaces: A novel low-cost method for detecting the presence of airborne hazardous mineral fibers

Naturally occurring fibrous minerals, such as erionite, can pose a significant threat to human health when disturbed and subsequently respired. Understanding the spatial abundance and characteristics of these hazardous fibrous minerals in ambient air is crucial for minimizing human exposure and assessing risk. Conventional detection methods for airborne hazardous mineral fibers, such as those developed for asbestos, are of limited utility in environmental settings where fiber concentrations are low and different fiber types may be present and can be costly especially when monitoring large areas over long periods of time. This study presents an innovative methodology for detecting and identifying the presence of airborne naturally occurring fibrous zeolites, using leaf surface deposition sampling, SEM-EDX analysis for the detection and assessment of elemental composition, and TEM-SAED with continuous rotation diffraction (MicroED) to determine their crystallographic unit cell parameters. In total, 309 fibrous zeolite particles (FZPs) were identified on a range of tree leaf surfaces across 80% of the sampling sites located close to both active and disused zeolite quarries in the Taupo Volcanic Region, New Zealand. The FZPs displayed various morphologies including aggregates, bundles, and fibril-like structures. Of the FZPs detected, 91.2% were < 5µm in length. Tetrahedral Si:(Si+Al) ratio results indicated that 40% of the FZPs were in the reference range for zeolite mordenite. TEM-SAED plus MicroED analysis resulted in 61% of tested FZPs indexed to unit cell parameters that matched with mordenite. This research demonstrates the potential of leaf sampling as a cost-effective method for detecting airborne FZPs while the MicroED data can be utilized for distinguishing between different types of airborne fibrous zeolites in ambient air.

Presence of asbestos in building materials and soils in postfire areas of Mati, Kineta and Varimbombi in Greece.

The present study was carried out to determine the presence of asbestos in Wildland Urban Interface (WUI) areas of Attica, Greece affected by wildfires between 2018 and 2021. It concerns the first major campaign that took place in Greece. The samples tested in this work were collected from prespecified buildings of the burned area. The samples included different types of building materials such as bricks, wall coatings, insulation plates etc. Soil samples nearby the buildings were also collected to examine dispersion of the fibers. The identification of asbestos was based on the optical properties of the fibrous particles and was performed with stereo microscope and Polarized Light Microscopy according to P401 provided by BOHS (Health and Safety Executive (HSE) 2021). Scanning Electron Microscopy with energy dispersive spectroscopy was also used to validate the presence of asbestos and determine its chemical composition. In this work, 2 different types of asbestos were determined, chrysotile and crocidolite. In some cases, fragments of asbestos containing materials were also detected in the afore-mentioned soil samples indicating dispersion of asbestos containing debris in an area around the burned spots. The presence of asbestos that was identified in this preliminary study could raise concerns to humans in the urban areas. For that reason, a risk assessment for the identified asbestos containing materials (ACMs) was conducted according to the guidelines on management and abatement of ACMs of Health and Safety Authority and the Asbestos: Survey guide, Appendix 4: Material assessment algorithm of Health and Safety Executive (HSE).

Removal of Arsenic from Contaminated Water by Polypyrrole-Based Adsorbents

Worldwide, there is growing concern over the toxicity of arsenic in drinking water. The US Environmental Protection Agency and Central Pollution Control Board (India) have set a safe limit of 50 parts per billion for arsenic in drinking water. Millions of people are at immediate risk due to high concentrations of arsenic in drinking water, particularly in developing nations where arsenic poisoning symptoms have been observed. One of the essential techniques described in this article is the absorption of arsenic from contaminated water by sustainable cellulosic materials like jute and wood sawdust after suitable modification. Jute and sawdust are cheap and abundantly available in South Asia. They are functionalized with polypyrrole coating by in situ chemical polymerization of pyrrole in aqueous medium in the presence of ferric chloride. Polypyrrole-coated jute fabric (with 11.28% polypyrrole add-on) and polypyrrole-coated sawdust (with 5.28% polypyrrole add-on) are found to be excellent adsorbers of arsenic ion (As3+) from water. The effect of dosage of polypyrrole-coated adsorbents, treatment time and pyrrole concentration on the As removal efficiency have been investigated in this work. The arsenic concentration in water is determined using a microwave plasma atomic emission spectrometer with the highest level of accuracy. Maximum As removal efficiency by the polypyrrole-coated sawdust and polypyrrole-coated jute fabric is found to be 80.90% and 97.3%, respectively, from a 50 mL, 7.5 parts per million As solution with a dosage of 1 g at neutral pH. The polypyrrole-coated jute and sawdust are characterized by Fourier-transform infrared spectroscopy to understand the chemical interaction between cellulose and polypyrrole molecules. The scanning electron microscope studies reveal a uniform coating of polypyrrole around the surface of jute fibre and sawdust particles. Thermo-gravimetric analysis shows good thermal stability of jute and sawdust after polypyrrole coating.

Distribution, flux, and risk assessment of microplastics at the Anzali Wetland, Iran, and its tributaries.

Microplastic pollution has raised significant concerns among scientific communities and society in recent years due to its increase and lesser-known effects on the environment. To improve the knowledge of microplastic pollution in freshwater, we investigated microplastics in Anzali Wetland, a Ramsar site in northern Iran, as well as its nine main entering rivers. The extracted microplastics were characterized via visual identification, SEM-EDX, and μ-Raman methods. Microplastics (size range: 50-5000 μm) were found in all water and sediment samples with concentration of fibrous particles as well as polypropylene and polyethylene polymers. The mean concentration of microplastics in bottom sediment and surface water samples of the wetland was 301 ± 222 particles∙kg-1 d.w. and 235 ± 115 particles∙m-3 (0.23 particles∙L-1), respectively. The microplastic concentration in the central and eastern parts of the wetland was higher than in other areas; however, the mean concentrations revealed homogeneity across the wetland area. Water properties (dissolved oxygen, pH, temperature, electrical conductivity, and salinity in water) did not affect the concentration of microplastic particles, though correlational analysis revealed a strong positive association between microplastic quantity and turbidity. There was a significant positive relationship between microplastic concentration and the percentage of clay in sediment samples. The quantity of microplastics in river water was higher than in wetland water, but the difference between the results was not significant. However, the quantity of microplastics in the river's littoral sediment was higher than in the bottom sediment of the wetland where the difference between the results was significant. Microplastic ecological risk assessment showed high potential ecological risk. The findings underscore the importance of effective management strategies and the implementation of policies to mitigate the negative impact of MP pollution on ecosystems and human health.

Optimization of microwave-produced coal-derived char insulation foam using response surface methodology

A new char-based insulation foam (CIF) is developed using coal-derived pyrolysis char (PC) and lignin, a paper and pulp industry byproduct. In this study, CIF is prepared by adopting the microwave method and Response Surface Methodology (RSM) is utilized to optimize predictions about the properties such as thermal conductivity, foam texture, compressive strength, and pore distribution of CIF. The three independent variables including percent char content, lignin/char ratio, and foaming agent/polyol ratio are considered in the RSM methodology. The face-centered central composite design is selected to obtain 17 test runs. Optimization of the predicted responses is performed to find the recipe considering a composite desirability function. Confirmatory test results show agreement between the predicted and observed values, with the percent error ranging from 0.00 % to 11.35 %, thereby confirming the accuracy of the prediction equations. The optimized CIF exhibits a thermal conductivity of 0.0633 W/m.K and a compressive strength of 695 kPa making it comparable to or better than traditional building insulation products such as fiber insulation, polymer composite, particle board, and ceramic glass foam. Therefore, this new CIF has the potential to be used as an energy-saving insulation material for building envelopes.

Thermomechanically micronized sugar beet pulp: Elucidating the interaction of soluble elements and insoluble fibrous particles for enhancing emulsification

The micronization of plant particles usually transfers substantial insoluble fraction into soluble elements, resulting in a soluble-insoluble binary system and the content of soluble elements can not be neglected. The present work aims to investigate the interaction between soluble elements and insoluble particles obtained from sugar beet pulp by microwave heating with ultrasonication, and their contribution to the synergistic emulsification performance. The soluble elements (∼40%) (sugar beet pectic substance, SBPS) and insoluble fibrous particles (IFPs) were separated from micronized sugar beet pulp (MSBP). Quartz crystal microbalance with dissipation analysis revealed that SBPS could irreversibly adsorb onto IFPs with an adsorbed mass of 32.2 μg/mg Fiber. By adopting sequential extraction and specific enzymatic hydrolysis for the modification of IFPs and SBPS, it was found that their non-saccharide fraction played an important role in the interaction. Larger molecular weight subfractions with abundant protein and ferulic acid content were the main adsorbable fraction in SBPS, and the interaction was driven by hydrophobic interaction. The soluble-insoluble binary system promoted the interfacial adsorption of both IFPs (from 65.6% to 82.2%) and SBPS (from 9.6% to 19.6%), forming a hybrid interfacial coverage (with SBPS-coated IFPs and SBPS) and endowing emulsion with better stability. These findings provided a guideline for understanding the emulsification mechanism of plant particles.

Technologies for Mechanical Recycling of Carbon Fiber-Reinforced Polymers (CFRP) Composites: End Mill, High-Energy Ball Milling, and Ultrasonication.

Carbon fiber reinforced polymer (CFRP) composites have very high specific properties, which is why they are used in the aerospace, wind power, and sports sectors. However, the high consumption of CFRP compounds leads to a high volume of waste, and it is necessary to formulate mechanical recycling strategies for these materials at the end of their useful life. The recycling differences between cutting-end mills and high-energy ball milling (HEBM) were evaluated. HEBM recycling allowed us to obtain small recycled particles, but separating their components, carbon fiber, epoxy resin, and CFRP particles, was impossible. In the case of mill recycling, these were obtained directly from cutting a CFRP composite laminate. The recycled materials resulted in a combination of long fibers and micrometric particles-a sieving step allowed for more homogeneous residues. Although long, individual carbon fibers can pass through the sieve. Ultrasonication did not significantly affect HEBM recyclates because of the high energy they are subjected to during the grinding process, but it was influential on end mill recyclates. The ultrasonication amplitude notably impacted the separation of the epoxy resin from the carbon fiber. The end mill and HEBM waste production process promote the presence of trapped air and electrostatics, which allows recyclates to float in water and be hydrophobic.

Investigation of cellulosic fines removal in dissolving pulp production with small-holed screen plates

This study investigates the influence of hole diameter and hole spacing on the fractionation performance using an industrial scale pressure screen. The objective is to increase the quality of the long fiber fraction during dissolving pulp production by separating cellulosic fines from unbleached softwood sulfite pulp containing 8% (w/w) primary fines (fibrous particles shorter than 0.200 mm fiber length). Different screen basket designs were applied, using the same hole spacing while varying hole diameter, and vice versa. This allowed a comparison of the separate influence of hole diameter and hole spacing on the separation efficiency. Production parameters of screening devices are always a compromise between separation efficiency, runnability/plugging, and throughput. High aperture velocity, high feed consistency and low reject rate were identified as the crucial operating parameters for high cellulosic fines removal efficiency, which turned out to be positive in terms of throughput. Considering the different hole diameters, the industrial trials showed that smaller holes yielded better fractionation results. Whereas reduced hole spacing resulted in a denser fiber network on the screen, reducing the amount of fines and short fibers passing, thereby leading to worse fractionation results. By choosing suitable screening conditions, we found that the weight-weighted fines content was reduced more than 50 percent using a one stage fiber fractionation screen set up under industrial conditions. The lowered fines content in the long fiber fraction is expected to allow a reduced purification effort and a lower chemical demand in the subsequent processes of dissolving pulp production. By reducing the fines fraction, consisting of short fibers, fiber fines, as well as mainly short-chain alkali-soluble carbohydrates (hemicelluloses), improvements in process efficiency and dissolving pulp quality can be achieved.

Evolution of bamboo derivative fiber-mollusk shell based calcite particulate hybrid reinforced epoxy bio-composites for sustainable applications

This study focused on the development of environmentally friendly epoxy-based biocomposites by incorporating bamboo fiber (BF) and calcite particles (CP) as reinforcements. A total of 125 specimens were fabricated with different weight percentages of BF and CP ranging from 0% to 15% to the epoxy. The biobased reinforcements were processed before incorporation, and the hand layup technique was used to fabricate the composites, which were then cured at ambient temperature. Evaluations of selected properties were carried out to ascertain the most probable areas of application, while the fracture surfaces were examined using SEM. The results indicated that the inclusion of these hybrid bio-reinforcements significantly enhanced the properties of the biocomposites compared to unreinforced samples. The optimal composition was identified as 12 wt% BF/CP, which demonstrated the highest ultimate tensile strength (32.84 MPa) and tensile modulus (1.9 GPa), attributed to the strong interfacial bonding between the epoxy matrix and the BF/CP reinforcements. Additionally, the flexural strength (55.38 MPa) and modulus (2.72 GPa) were improved due to the effective load transfer and stiffening effect of the calcite particles. The hardness (67 HS) and wear index (0.015 mg) were enhanced by the toughening mechanism provided by the bamboo fibers, while the density (1.195 g/cm³) remained within a desirable range for lightweight applications. Composites with 9 wt% BF/CP exhibited the highest impact strength (22.66 J/m2), likely due to the optimal balance of fiber-matrix interaction and energy absorption capacity. These findings indicate that the developed hybrid-reinforced biocomposite compositions hold great promise with the improved physical and mechanical properties as seen and can be utilized for various applications, including automotive, aerospace, and other engineering applications.

In-Vitro Analysis of Polyethylene Liner Wear Performance at 3 and 5 Million Cycles

The purpose of this study is to compare the wear properties of UHMWPE acetabular liners after undergoing 3 million (3 Mc) and 5 million (5 Mc) cycles of in-vitro wear testing. The results will serve as a reference for the design of in-vitro testing for hip prostheses and as a control for clinical revision removals. Wear tests were conducted on three different sizes of acetabular liners (28 mm, 32 mm, and 36 mm internal diameters) using a hip simulator to determine the amount of wear after 3 and 5 million cycles. The analysis included the number, size, and shape of abrasive particles. After 3 and 5 million cycles of wear, the amount of wear on the acetabular liner increased as the inner diameter increased. The abrasive particles had an average equivalent circular area diameter (ECD) of 0.27 μm and 0.29 μm, and 94.4% and 90.1% of the aspect ratio (AR) less than 4. The amount of wear on the acetabular liner after 3 Mc wear can indicate the wear performance of the product. The number of particles increased and the percentage of fibrous particles was higher after 5 Mc wear compared to 3 Mc wear.