Composite Fibers Research Articles

Electrospinning of LaB6/PEDOT:PSS/PEO Fiber Composites of Unique Morphologies.

We present a direct electrospinning fabrication technique for the manufacture of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)/poly(ethylene oxide) (PEDOT:PSS/PEO) polymer fibers containing embedded cubic lanthanum hexaboride (LaB6) particles. We focus on the impact of relative humidity on the formation of uniform polymer fibers and show that a relative humidity of 5% is optimal, resulting in an average fiber thickness of 266 ± 88 nm. As the relative humidity is increased, the fibers contain beads as a consequence of Rayleigh instabilities. The addition of lanthanum hexaboride cubic particles to the polymer solution before electrospinning results in the encapsulation of the LaB6 particles inside the fibers. We investigate the effect of LaB6 particle size on morphology and observe that particles of ∼500 nm yield a fiber-cube-fiber morphology, while 2 μm particles result in fewer embedded cubes along the length of the polymer fibers. This phenomenon likely arises from electrodynamic interactions between the LaB6 particles in the polymer solution and the electric field lines generated during electrospinning between the spinneret and the collector. Our results display the versatility of the electrospinning technique in the fabrication of unique polymer/hexaboride composite fibers.

Multiferroicity and Semi‐Cylindrical Alignment in Janus Nanofiber Aggregates

Abstract1D multiferroic fibers are known to exhibit attractive characteristics, including enhanced magnetoelectric (ME) coupling compared to thin film and bulk architectures. A comprehensive understanding of composite fibers, however, has been hindered by the complexity of their structure, leading to limited reports. Here, clear and strong ME coupling is experimentally detected in a composite Janus nanofiber aggregate using second harmonic generation (SHG) polarimetry under different magnetic field orientations. The observation of such a pronounced effect using an all‐optical method has not been previously reported in multiferroic fibers. A series of global fits is performed to the SHG polarimetry results to investigate the behavior of nanofibers within an aggregate. We find the magnetically assembled fibers exhibit semi‐cylindrical alignment as well as the expected lengthwise alignment despite variations in size and composition from fiber to fiber. The ME coupling and the semi‐cylindrical alignment seen in SHG are further corroborated via X‐ray diffraction under similar magnetic field conditions. These findings contribute to the development of complex composite and multifunctional devices using multiferroic nanostructures as building blocks, even those with inhomogeneous shapes and geometries.

Comparative Analysis of Mechanical and Morphological Properties of Cordenka and Ramie Fiber-Reinforced Polypropylene Composites

The depletion of conventional materials and their adverse environmental impacts have prompted a shift toward sustainable alternatives in composite materials engineering. In pursuit of this objective, this study investigated the mechanical properties of polypropylene matrix composites reinforced with Cordenka, an artificial cellulose fiber, and compared them to those reinforced with ramie, a natural cellulose fiber. Continuous strand composites were developed using the Multi-Pin-assisted Resin Infiltration (M-PaRI) process. The strands were subsequently sectioned into 15 mm lengths and injection-molded into dumbbell and strip specimens for mechanical characterization. The results showed that 20 wt% Cordenka/PP composites exhibited a tensile strength of 68.7 MPa, 2.04 times higher than neat PP and 1.66 times greater than the 20 wt% ramie/PP composites. Impact testing further demonstrated that Cordenka/PP composites absorbed 2 to 2.5 times more impact energy than ramie/PP composites, regardless of the presence of notches. Fiber length analysis indicated that Cordenka fibers maintained their length beyond the critical fiber length, allowing for efficient stress transfer and acting as a more effective reinforcement compared to ramie fibers, which were below this threshold. Consequently, the Cordenka/PP composites exhibited significantly enhanced mechanical performance. Scanning electron microscopy (SEM) analysis revealed fewer fiber pullouts in ramie-reinforced composites, suggesting superior interfacial adhesion to the PP matrix, although it did not translate to higher mechanical properties. These findings underscore the potential of Cordenka as a sustainable alternative to synthetic, non-biodegradable fibers in PP composites, providing improved mechanical properties and promising prospects for advanced composite applications.

Evaluation of SMA-13 Asphalt Mixture Reinforced by Different Types of Fiber Additives

This research aims at systematically evaluating the properties of SMA-13 asphalt mixture reinforced by several fiber additives including flocculent lignin fiber (FLF), granular lignin fiber (GLF), chopped basalt fiber (CBF), and flocculent basalt fiber (FBF). Firstly, the thermal stability, moisture absorption, and oil absorption property of these fiber additives were analyzed. Secondly, the property of SMA-13 reinforced using four types of single fibers and two kinds of composite fibers (FLF + CBF and FLF + FBF) was comprehensively analyzed. Specifically, the high-temperature performance was evaluated using the uniaxial penetration test and the rutting test, the medium-temperature anticracking property was evaluated using the IDEAL-CT test, the low-temperature property was analyzed using the beam bending test, and the water stability was studied by the freeze–thaw splitting test. Thirdly, the dynamic mechanical response of different-fibers-modified SMA-13 was evaluated using the uniaxial compression dynamic modulus test. Finally, correlation analysis between the results of dynamic modulus and the high-, medium-, and low-temperature mechanical performance was carried out. The research results reveal that the stability of CBF and FBF under thermal action is better than that of GLF and FLF, and FBF shows the best thermal stability. The oil absorption property of FLF is better than that of GLF, followed by FBF and CBF. The comprehensive mechanical properties of CBF- and FBF-reinforced SMA-13 are better than those of FLF- and GLF-modified SMA-13. CBF can better reinforce the mechanical property of SMA-13 under low and medium temperature, while FBF can better reinforce the performance of SMA-13 at high temperature. FLF/CBF- and FLF/FBF-composite-modified SMA-13 show better high-temperature mechanical performance than that of the single-fiber-reinforced mixture, and FLF has some negative impact on the properties of FLF/FBF-composite-modified SMA-13 at low temperature. Fibers have no significant influence on the water stability of the mixtures. Meanwhile, the linear correlation between the mechanical performance of all the fiber-reinforced SMA-13 and the dynamic modulus result is good.

Covalently grafting silane coupling agents onto MXene‐reinforced carbon fibers for epoxy composites with improved mechanical properties

AbstractTwo‐dimensional (2D) MXene (MX) and silane coupling agents are increasingly used to modify carbon materials for the fabrication of composite functional materials, which exhibit enhanced electrical, optical, and mechanical properties due to the synergistic effects of both MX and silane. We demonstrate the modification of carbon fibers (CFs) with MX and three different kinds of silane coupling agents, including 3‐aminopropyltriethoxysilane, 3‐glycidyloxypropyldimethoxymethylsilane, and 3‐mercaptopropyltriethoxysilane, which are named as CF‐MX@N, CF‐MX@O, and CF‐MX@S, respectively, and further prepare the CF‐MX@silane/epoxy (EP) composites. The utilized silane coupling agents serve as bridges between MX and CFs, forming CF‐MX@silane composites. Through comparative analysis, it is found that the CF‐MX@S composites form a strong interface phase through covalent bonds, significantly enhancing the interface compatibility and revealing strong interface adhesion. The interfacial shear strength of the molded CF‐MX@S/EP composites increases to 119.7 MPa, with an 173.9% enhancement comparing to unmodified composites. This work can offer useful guidance and reference for selecting appropriate silane coupling agent to modify CFs with 2D materials to form high‐performance composite materials.Highlights Silane coupling agents are used as bridges to graft MXene‐modified CFs The surface modification of CFs is achieved by a simple one‐step approach Excellent interfacial phase is constructed through forming strong covalent bonds Microstructure and failure interface are responsible to interface strengthen.

High performance composite hollow fiber nanofiltration membrane fabricated via the synergistic effect of co-solvent assisted interfacial polymerization and macrocyclic polyamine incorporation

The necessity for high-performance thin film composite (TFC) nanofiltration (NF) membranes for drinking water and wastewater treatment is becoming increasingly apparent in the face of the global water crisis. In this work, co-solvent (acetone) assisted interfacial polymerization (CAIP) and incorporating macrocyclic polyamine (Cyclen) as an aqueous co-monomer were employed to fabricate hollow fiber (HF) NF membrane and to enhance the permeability and the selectivity, respectively, thereby overcoming the inherent trade-off effect. The effects of Cyclen and acetone on the separation performance were comprehensively investigated, and the interfacial polymerization conditions were optimized. The optimal HF NF membrane exhibits a 68.6 % increment in water permeance relative to the baseline membrane while without sacrificing the Na2SO4 rejection which is as high as 99.2 %. In particular, it exhibits a superior high pure water permeability of 222.5 L m−2 h−1 MPa−1, ranking among the highest observed for HF NF membranes in the existing literature. Moreover, it exhibits excellent acid resistance as well as fouling resistance. This research paves a novel approach for developing high-performance HF NF membranes for water and wastewater treatment.

Development of Turbocharging-Ability Hybrid Nanogenerators Comprising Bipolar PVDF-HFP/MXene Electrospun Composites.

Coupling piezo-active and triboelectric materials has recently emerged as an effective technique for developing high-performance hybrid nanogenerators (HNGs). This is the first paper to report the fabrication of piezo-active poly(vinylidene fluoride-hexafluoropropylene)(PVDF-HFP)/MXene-based hybrid composite fibers through conventional electrospinning. Here, the effect of MXene content (1-5%) on the surface potential and electrical performance of the as-synthesized composites is investigated and optimized. PVDF-HFP/3% MXene (PHM3)/Nylon 12+A-rGo (NY2)-HNG, which contains the best-performing composite (PMH3; containing 3% of MXene), exhibits turbocharging properties (charging a 10 µF capacitor with 16V within 100 s) and can continuously operate low-power electronics. Interestingly, PHM3 (with a negative surface potential) is transformed into PPHM3 (with a positive surface potential of +2190V) via corona poling. This study proposes a new class of HNGs containing frictional layers comprising bipolar PVDF-HFP/3% MXene composites (PHM3/PPHM3-HNG) with an excellent output performance of 297V and 5.1µA that exhibit broad application prospects in energy harvesting.

Recent Advances in Additive Manufacturing of Fibre-Reinforced Materials: A Comprehensive Review

Additive manufacturing (AM) plays a significant role in the 4th Industrial Revolution due to its flexibility, allowing AM equipment to be connected, monitored, and controlled in real time. In advance, the minimum waste of material, the agility of manufacturing complex geometries, and the ability to use recycled materials can provide an advantage to this manufacturing method. On the other hand, the poor strength and durability of the thermoplastics used in the manufacturing process are the major drawback that keeps AM behind common production methods such as casting and machining. Fibre-reinforced polymers can enhance mechanical properties, advance AM from the commonly used polymers, and make AM competitive against conventional production methods. The main focus of the current review is to examine the work conducted in the field of reinforced additively manufactured technologies in the literature of recent years. More specifically, this review discusses the conducted research in the composite fibre coextrusion (CFC) additive manufacturing techniques developed over the past years and the materials that can be used. In addition, this study includes an up-to-date comprehensive review of the evaluation of fibre-reinforced 3D printing along with its benefits in terms of mechanical response, namely tensile, flexural, compression and energy absorption, anisotropy, and dynamic properties. Finally, this review highlights possible research gaps regarding fibre-reinforced AM and proposes future directions, such as deeper investigations into energy absorption and anisotropy, to position fibre-reinforced AM as a preferred fabrication method for ready-to-use parts in cutting-edge industries, including automotive, aerospace, and biomedical sectors.

Core-Sheath Fibers via Single-Nozzle Spinneret Electrospinning of Emulsions and Homogeneous Blend Solutions.

The preparation of core-sheath fibers by electrospinning is a topic of significant interest for producing composite fibers with distinct core and sheath functionalities. Moreover, in core-sheath fibers, low-molecular-weight substances or nanosized inorganic additives can be deposited in a targeted manner within the core or the sheath. Commonly, for obtaining a core-sheath structure, coaxial electrospinning is used. It requires a coaxial spinneret and suitable immiscible solvents for the inner and outer solutions. The single-nozzle spinneret electrospinning of emulsions can address these issues, but use of a stabilizing agent is needed. A third approach-preparation of core-sheath fibers by single-nozzle spinneret electrospinning of homogeneous blend solutions of two polymers or of a polymer/low-molecular-weight substance-has been much less studied. It circumvents the difficulties associated with the coaxial and the emulsion electrospinning and is thoroughly discussed in this review. The formation of core-sheath fibers in this case is attributed to phase-separation-driven self-organization during the electrospinning process. Some possibilities for obtaining core-double sheath fibers using the same method are also indicated. The gained knowledge on potential applications of core-sheath fibers prepared by single-nozzle spinneret electrospinning of emulsions and homogeneous blend solutions is also discussed.

Blast response and protection level of concrete composite wall panels made with recycled tyre fibres in a cement matrix

This paper investigates the blast response and protection level of a new blast-resistance wall panels made of Recycled Tyre Fibres Concrete (RTFC) as an exterior protective layer compositely connected to a concrete wall through experiments and numerical modelling. RTFC is a novel sustainable cement-based versatile composite, made with recycled non-biodegradable material (tyre rubber particles) in the form of composite fibres in a cement matrix, with applications in blast and ballistic protection that features high dynamic properties. Three composite wall panels were constructed and subjected to blast loads generated by Advanced Blast Simulator (ABS). Three different loading scenarios, each with an intensity capable of causing complete structural failure, were applied. The blast wave characteristics, such as the imposed overpressure and impulse, were measured alongside the deflection of the specimens. The wall specimens could withstand the blast loads with minimal damage. No cracks were observed in the RTFC layer, with only minor cracks appearing on the concrete side of the wall. The protection performance of the wall specimens was examined following UFC guidelines, revealing their outstanding resistance to blast loads. Moreover, in line with these guidelines, the composite wall panel is eligible for a High Level of Protection (HLoP) classification. Finally, a Single Degree of Freedom (SDOF) analytical model was developed for the wall panel to determine the Dynamic Increase Factor (DIF) of RTFC. The analysis resulted in a DIF value of 1.5, which was then incorporated into the numerical models of the walls. The accuracy of the DIF was validated by comparing the numerical results with experimental data, confirming its reliability.

Application and research of three-dimensional composite fiber interlayer in lithium-sulfur battery

Lithium-sulfur (Li-S) batteries are regarded to be the most probable‌ electrochemical energy storage devices for large-scale applications because of their high energy and green characteristics. Nevertheless, the polysulfides generated during the cycle of Li-S batteries can cause the "shuttle effect", reducing the utilization rate of sulfur (S) and electrochemical performance. In this study, a novel three-dimensional composite fiber (TDCF) interlayer was prepared and placed between the S cathode and the PP separator to adsorb polysulfide and restrain the "shuttle effect". The results show that the capacity retention rate of Li-S battery is still higher 3:50 ratio, 200ml of anhydrous ethanol was added to moisten, than 70% after 200 charge-discharge cycles at 1C.

An Experimental Investigations on Design and Weight Optimization for a Light Motor Vehicle (LMV) Drive Shaft Using a Composite Material Aluminum and Glass Fiber (Al + GF)

Aluminum is primarily used in Metal Composites because of its lighter weight and higher strength. Glass fibers are wound around an aluminum shaft to create the composite. ANSYS results determine the relative amounts of aluminum and Eglass fiber in each shaft. The purpose of this study is to use a torsion test to evaluate the mechanical performance of a composite shaft composed of aluminum and glass fiber. The results are carefully examined for different combinations of glass fiber layers and aluminum layers. When the weight proportion of aluminum in the composite increases, the mechanical properties of the composites improve.

Regulated crystallization and piezoelectric properties of bio-based poly(L-lactic acid)/ diatomite composite fibers by electrospinning

Regulated crystallization and piezoelectric properties of bio-based poly(L-lactic acid)/ diatomite composite fibers by electrospinning

Enhancement of 5-Fluorouracil Drug Delivery in a Graphene Oxide Containing Electrospun Chitosan/Polyvinylpyrrolidone Construct.

Electrospun nanofibrous mats, consisting of chitosan (CS) and polyvinylpyrrolidone (PVP), were constructed with the addition of graphene oxide (GO) for enhancement of delivery of the 5-Fluorouracil (5-Fu) chemotherapy drug. Upon studying the range of GO concentrations in CS/PVP, the concentration of 0.2% w/v GO was chosen for inclusion in the drug delivery model. SEM showed bead-free, homogenous fibres within this construct. This construct also proved to be non-toxic to CaCo-2 cells over 24 and 48 h exposure. The construction of a drug delivery vehicle whereby 5-Fu was loaded with and without GO in various concentrations showed several interesting findings. The presence of CS/PVP was revealed through XPS, FTIR and Raman spectroscopies. FTIR was also imperative for the analysis of 5-Fu while Raman exclusively highlighted the presence of GO in the samples. In particular, a detailed analysis of the IR spectra recorded using two FTIR spectrometers, several options for determining the concentration of 5-Fu in composite fibre systems CS/PVP/5-Fu and GO/CS/PVP/5-Fu were demonstrated. By analysis of Raman spectra in the region of D and G bands, a linear dependence of ratios of integrated intensities of AD and AG on the intensity of host polymer band at 1425 cm-1 vs. GO content was found. Both methods, therefore, can be used for monitoring of GO content and 5-Fu release in studied complex systems. After incorporating the chemotherapy drug 5-Fu into the constructs, cell viability studies were also performed. This study demonstrated that GO/CS/PVP/5-Fu constructs have potential in chemotherapy drug delivery systems.

P3HT/g-C3N4 composite fiber membranes for high-performance photocatalytic hydrogen evolution

As a superstar semiconducting polymer, poly(3-hexylthiophene) (P3HT) demonstrates high efficiency in carrier transport ability and wide absorption range. However, pristine P3HT exhibits minimal photocatalytic activity as a result of its short carrier transport distance and fast electron-hole recombination. Here, we strategically fabricated P3HT/g-C3N4 composites on polymethyl methacrylate (PMMA) fiber (PTCN) via electrospinning and the physicochemical properties were fully investigated. Raman spectroscopy, ultraviolet–visible (UV–Vis) absorption spectra and X-ray photoelectron spectroscopy (XPS) results demonstrated a well-defined p-n heterojunctions can be formed between P3HT and g-C3N4 molecules through π-π interaction and extended conjugated length of P3HT could be achieved by tuning the ratios of P3HT relative to g-C3N4. The presence of the heterojunctions facilitates the effective disconnection of the electron-hole pairs, resulting in a significantly enhanced photocatalytic hydrogen evolution rate of 7327 μ mol/(h·g) for the PTCN fiber membranes. This value exceeds that of P3HT fibers by 57.7 times and powder g-C3N4 by 6.8 times, respectively. The high photocatalytic hydrogen production activity of P3HT/g-C3N4 fiber membrane expands the application of P3HT. More importantly, these results indicate that the construction of heterojunction fiber materials is a promising approach for improving the photocatalytic ability of conjugated semiconducting polymers.

Effect of high quality hybrid coatings and coating condition on the properties of continuous glass fiber reinforced polypropylene prepreg composites

AbstractDue to the difficulty in infusing resin into interiors of fiber bundles by prevalent pre‐impregnation methods like melt impregnation and the substantial polarity difference between glass fibers (GF) and polypropylene (PP), the application of continuous glass fiber reinforced polypropylene (CGF/PP) composites has been restricted. In this study, a hybrid emulsion is prepared to address the polarity difference through coating process. And further by optimizing coating process parameters, composites glass fibers with excellent performance can be obtained. The study demonstrates that the composite glass fiber with coating amount of 15.34% exhibits good bunching and flexibility. The monofilament tensile strength and interfacial shear strength (IFSS) are increased by 2.53% and 109.74%, respectively compared to the desized glass fiber (GF0). Furthermore, after the hot‐pressing process, the composites glass fiber bundles show fully filled gaps and a completely wrapped surface. This study lays the foundation for producing CGF/PP prepreg composites conveniently, efficiently, and commercially.

Recent advances in H2 purification and CO2 capture: Evolving from flat sheet to hollow fiber membranes

Hydrogen (H2) production and demand have steadily increased, leading to a rise in carbon dioxide (CO2) emissions since fossil fuels are the current raw material for H2 production. Thin film composite (TFC) hollow fiber membranes have become significant in H2 purification and CO2 capture, playing a critical role in developing next-generation fuels and supporting the United Nations Sustainable Development Goal 7 (SDG 7) – Affordable and Clean Energy, with the goal of providing universal access to clean, advanced, and renewable energy for all. However, the polymeric selective layer of TFC membranes faces a trade-off between permeability and selectivity, as well as challenges including CO2 plasticization and physical aging. Additionally, H2/CO2 separation remains particularly challenging because H2, being diffusivity-selective, permeates more quickly through the membrane due to its smaller molecular size and higher kinetic energy, while CO2, being solubility-selective, has a high affinity for dissolving in most polymeric membranes. Herein, this review provides an in-depth exploration of innovative modification strategies designed to overcome these challenges in glassy polymeric membranes and enhance H2 separation performance in the recent 10 years. Various nanofillers, such as metal-organic frameworks (MOFs) such as University of Oslo (UiO), Materials Institute Lavoisier (MILs), and Zeolitic Imidazolate Frameworks (ZIFs), have shown remarkable potential in boosting gas separation capabilities due to their superior compatibility with polymer matrices and tunable properties. The review also explores different types of hollow fiber membranes, including single layer, dual-layer, and TFC, alongside fabrication techniques like interfacial polymerization and dip-coating. Critically, the analysis highlights cutting-edge strategies to improve membrane performance, such as (i) thermal cross-linking, (ii) chemical cross-linking, (iii) ultraviolet (UV) cross-linking, (iv) polymer blends, and (v) modified fillers, along with their objectives and expected outcome. Furthermore, the review spotlights breakthroughs in H2/CO2, H2/CH4, and H2/N2 separation technologies, emphasizing the critical need for continued innovation to drive sustainable H2 production and meet the growing clean energy demand.

Pullulan/Collagen Scaffolds Promote Chronic Wound Healing via Mesenchymal Stem Cells

This study investigated the development of Pullulan/Collagen nanofiber scaffolds integrated with mesenchymal stem cells (MSCs) to enhance chronic wound healing. The combination of these biopolymers aims to optimize the scaffold properties for cell growth, viability, and tissue regeneration. Materials and Methods: Pullulan, Collagen, and Pullulan/Collagen composite nanofibers were fabricated using electrospinning. The fibers were characterized using scanning electron microscopy (SEM) to determine the fiber diameter, and Fourier-transform infrared spectroscopy (FTIR) was employed to assess the molecular interactions. Cell viability was evaluated using MSCs cultured on the scaffolds and apoptosis assays were conducted to assess cell health. Distilled water was used as the solvent to maximize biocompatibility. Results: SEM analysis revealed that Pullulan nanofibers exhibited a larger average diameter (274 ± 20 nm) compared to Collagen fibers (167.03 ± 40.04 nm), while the Pullulan/Collagen composite fibers averaged 280 ± 102 nm. FTIR confirmed the molecular interactions between Pullulan and Collagen. Regarding biocompatibility, the Pullulan/Collagen scaffold demonstrated superior cell viability at 99% compared to 91% for Pullulan alone. Apoptosis assays indicated significantly lower necrosis rates for the composite scaffold (1.29%) than for the Pullulan-only scaffolds (2.35%). Conclusion: The use of distilled water as a solvent played a critical role in increasing cell viability and facilitating healthy proliferation of MSCs without cellular damage. Additionally, the reduced platelet activation and macrophage activity (0.75-fold for both) further supported the biocompatibility of the Pullulan/Collagen scaffold, demonstrating its potential for tissue engineering and chronic wound healing applications.

Facile Approach for the Fabrication of Vapor Sensitive Spin Transition Composite Nanofibers

In this work polymer nanofibers were functionalized by incorporation of the spin transition (ST) compound [Fe(H2btm)2(H2O)2]Cl2 (FeH2btm) (H2btm = di(1H‐tetrazol‐5‐yl)methane). FeH2btm is an interesting compound due to its ability to reversibly and sensitively switch between high spin (HS) and low spin (LS) state when exposed to common volatile compounds (VOC) like ammonia and methanol. By using polyvinylidene fluoride (PVDF) as the main compound, inhibiting interactions between the complex and polymer were minimized. By using UV‐Vis spectroscopy, the visible and reversible switching between HS and LS state when exposed to an ammonia or hydrochloric acid atmosphere was confirmed. Powder X‐Ray diffraction (PXRD), scanning electron microscopy (SEM) and energy dispersive X‐Ray spectroscopy (EDX) show a homogenous distribution of FeH2btm with no major crystalline accumulations and a mean fiber diameter of 106 ± 20 nm. The composite fiber has a similarly high thermal stability as the pure FeH2btm, as shown by thermogravimetric analysis (TGA). Mössbauer spectroscopy indicates an incomplete spin transition after exposition to ammonia. This could be due to low permeability of the VOC into the composite fiber.

Hybrid Geopolymer Composites Based on Fly Ash Reinforced with Glass and Flax Fibers

This article’s aim is to analyze physical, mechanical, and fracture properties as well as the thermal investigation of geopolymer composites reinforced with flax, glass fiber, and also the hybrid combination of fibers. Two types of matrices were considered as composites matrices. The first composition was based on fly ash and river sand. The second matrix composition contained fly ash and glass spheres. The content of reinforcement was 1% by mass. Compressive strength and three-point bending fracture tests were performed. The values of fracture toughness and fracture energy were determined. The resonance method was used to verify the dynamic characteristics, such as the dynamic modulus of elasticity and the dynamic Poisson ratio. The results show that single-type fibers in composites based on fly ash and glass spheres did not affect compressive strength. However, introducing hybrid reinforcement increased compressive strength by about 10% compared to the reference specimens. Flax fibers and hybrid reinforcement ensured higher fracture toughness and energy. The results also revealed great potential for glass sphere application to geopolymer materials in terms of fracture mechanics and thermal properties. Despite the lower strength properties in relation to geopolymers based on sand aggregate, applying reinforced fibers into the composite with glass spheres enhanced the compressive strength compared to other materials. Materials modified with glass spheres have a thermal conductivity twice as low as that of materials containing river sand.