Fiber Fabry-Perot Interferometer Research Articles

Analysis of the Sapphire Fiber Fabry-Perot Interferometer Fringe Visibility under Different Excitation Conditions

In this paper, a theoretical analysis of how the excitation conditions affect the sapphire fiber Fabry-Perot interferometer (SFPI) visibility was performed. The conditions were considered, in which an SFPI was excited by a single-mode fiber (SMF), a multimode fiber (MMF), and a fiber collimator. The finite difference method (FDM) was used to realize the numerical solution of the modal electric fields, and then, the modal excited distributions in the sapphire fiber and the SFPI visibility were calculated. The results showed that different numbers of modes were excited in sapphire fibers under different excitation conditions and finally affected the fringe visibility of the SFPI. The fiber collimator excited the fewest modes and the visibility remained at the highest level. Finally, an experiment was performed, and the experimental results agreed well with the theoretical results.

Temperature-compensated high strain measurement based on a Fabry–Perot interferometer with the virtual-assisted Vernier effect

A highly sensitive optical fiber Fabry–Perot interferometer (FPI) for strain measurement with temperature compensation is proposed. Instead of using another actual reference interferometer, a virtual FPI is constructed to superpose with the sensing FPI to form the Vernier effect. The fundamental and the first-order harmonic Vernier effect are generated to increase the sensitivity by adjusting the parameter of the virtual FPI. In order to separate the strain from the environment temperature, an FBG is cascaded to distinguish the applied temperature. Experimental results demonstrate that, with the help of the fundamental Vernier effect, the sensitivity and temperature of the FPI increases from 1.05 pm/°C to 10.63 pm/°C in the temperature range of 40-120°C, and the sensitivity of strain increases from 2.635 pm/µε to 33.11 pm/µε in the strain range of 0-400 µε. In order to access the tracking points more easily and further enhance the sensitivities, the first-order harmonic Vernier effect is generated by modifying the virtual FPI. Results show that the temperature and strain sensitivities are 21.25 pm/°C and 62.25 pm/µε, respectively. In addition, with the help of the FBG, the strain can be separated from the temperature by solving the cross-sensitivity matrix.

Label-free and selective heparin detection by surface functionalized fiber Fabry-Perot interferometer biosensor

Heparin (Hep) is the most commonly used anticoagulant drug in clinical settings, and precise dosage control is crucial. To enable rapid and accurate quantification of Hep concentration in clinical practice, a label-free and selective fiber-optic Fabry-Perot interferometric (FPI) biosensor detection method based on graphene oxide (GO) was proposed. This method utilizes protamine (PRTM) sulfate as the modified layer and achieves Hep detection through layer-by-layer (LBL) assembly. In this study, we developed a label-free and selective fiber optic FPI biosensor for the detection of Hep using GO. The GO on the surface layer of the fiber optic FPI biosensor was treated with specific functionalization, it enables specific interaction with Hep. The binding of Hep to the functionalized surface induces a change in the luminal light signal, which can be monitored within the cavity for rapid and accurate detection of Hep. The results demonstrate that this biosensor exhibits good sensitivity, with a value of 10.82 nm/mM in the low-concentration control group, and an average limit of detection (LOD) calculated as 31μg/mL in the low-concentration group. This study presents a label-free, selective and efficient method for biomedical science testing that holds great potential for widespread application in clinical medicine.

Optimization of the coupling efficiency under self-injection locking in a narrow linewidth hybrid wavelength tunable laser diode

In this study, a fiber Fabry–Perot (FFP) interferometer was connected to a hybrid wavelength-tunable laser diode consisting of a semiconductor optical amplifier chip and Si photonics chip, and spectral linewidth narrowing was achieved using the self-injection locking effect. The hybrid wavelength-tunable laser was equipped with a variable-reflectivity mirror, which allowed the optimization of κ, the coupling efficiency between the laser cavity and FFP interferometer. By optimizing κ, self-injection locking stabilized, and the linewidth was controlled between 4 and 300 kHz. This laser can be used to evaluate the linewidth required for communication systems such as digital coherent communication and the accuracy required for distance measurement.

High pressure-sensitive and stable fiber Fabry-Perot interferometer with nano-diaphragm assembled by H-O catalysis bonding.

Herein, a high pressure-sensitive and stable fiber Fabry-Perot (FP) interferometer with nano-diaphragm assembled by H-O catalysis bonding is proposed and demonstrated. In order to assemble a nano-diaphragm-based fiber FP interferometer by H-O catalysis bonding technique, a SiO2 film, introduced as a bridging layer on the nano-diaphragm, can be regarded as a solid adhesive to bridge hollow-core fiber end-face and nano-diaphragm. As thus, by depositing bonded layers on different diaphragm materials, this H-O catalysis bonding technology can be used to for assembling FP interferometer with different materials nano-diaphragms. Experimentally, Si nano-diaphragm is transferred to hollow-core fiber end-face to build a stable fiber FP interferometer without polymeric adhesive. Experimental results reveal that this Si nano-diaphragm-based fiber FP interferometer has a high (79.6 pm/kPa) pressure sensitivity and a low (17.3 pm/°C) temperature sensitivity. Besides that, different materials nano-diaphragm also can be assembled by using this H-O catalysis bonding technique, and the functional FP interferometer can be realized by using functional nano-diaphragm material. Thus, a Pd nano-diaphragm is successfully assembled to build a FP interferometer with a hydrogen concentration measurement capacity. Further investigation will focus on exploitation of multi-material nano-film patterning transfer and different nano-film integration by using this H-O catalysis bonding transfer.

Miniature Optical Fiber Fabry-Perot Interferometer Based on a Single-Crystal Metal-Organic Framework for the Detection and Quantification of Benzene and Ethanol at Low Concentrations in Nitrogen Gas.

This study reports for the first time, to the best of our knowledge, a real-time detection of ultralow-concentration chemical gases using fiber-optic technology, combining a miniaturized Fabry-Perot interferometer (FPI) with metal-organic frameworks (MOFs). The sensor consists of a short and thick-walled silica capillary segment spliced to a lead-in single-mode fiber (SMF), housing a tiny single crystal of HKUST-1 MOF, imparting chemoselectivity features. Ethanol and benzene gases were tested, resulting in a shift in the FPI interference signal. The sensor demonstrated high sensitivity, detecting ethanol gas concentrations (EGCs) with a sensitivity of 0.428 nm/ppm between 24.9 and 40.11 ppm and benzene gas concentrations (BGCs) with a sensitivity of 0.15 nm/ppm between 99 and 124 ppm. The selectivity study involved a combination of three ultralow concentrations of ethanol, benzene, and toluene gases, revealing an enhancement factor of 436% for benzene and 140% for toluene, attributed to the improved miscibility of these conjugated ring molecules with the alkane chains of the ethanol-modified HKUST-1. Experimental tests confirmed the sensor's viability, demonstrating significantly improved response time and spectral characteristics through crystal polishing, indicating its potential for quantifying and detecting chemical gases at ultralow concentrations. This technology may prevent energy resource losses, and the sensor's small size and robust construction make it applicable in confined and hazardous locations.

Ultraviolet-induced sensitivity enhancement of a fiber tip temperature sensor based on adhesive-TiO2 double-cavity composite Fabry-Perot interferometer

A composite fiber Fabry-Perot interferometer (FPI) -based optical fiber temperature sensor is theoretically proposed and practically demonstrated in this work, in which the composite FPI is formed by covering the end face of single-mode fiber with ultraviolet (UV) adhesive and nano-TiO2 coating using the dip-coating method. With the superior thermo-optic characteristic of UV adhesive and the UV absorption of nano-TiO2, the sensitivity of the composite FPI temperature sensor can be effectively enhanced by UV irradiation. After five times of TiO2 dip-coating processes, the composite FPI has a higher temperature sensitivity of 75.3 pm/°C (R2 = 0.9754) under 365 nm UV light, in which the measurement range is from 25 °C to 130 °C and the detection accuracy is 0.66 °C. The proposed sensor has a simple structure and preparation process, competitive sensitivity, high linearity, and satisfactory repeatability and stability, which can be an appropriate candidate to realize high-precision temperature sensing in industrial, chemical, biological, and environmental applications.

Highly Sensitive Temperature Sensor Based on Vernier Effect Using a Sturdy Double-cavity Fiber Fabry-Perot Interferometer.

Temperature measuring is a daily procedure carried out worldwide in practically all environments of human activity, but it takes particular relevance in industrial, scientific, medical, and food processing and production areas. The characteristics and performance of the temperature sensors required for such a large universe of applications have opened the opportunity for a comprehensive range of technologies and architectures capable of fulfilling the sensitivity, resolution, dynamic range, and response time demanded. In this work, a highly sensitive fiber optic temperature sensor based on a double-cavity Fabry-Perot interferometer (DCFPI) is proposed and demonstrated. Taking advantage of the Vernier effect, we demonstrate that it is possible to improve the temperature sensitivity exhibited by the polymer-capped fiber Fabry-Perot interferometer (PCFPI) up to 39.8 nm/°C. The DCFPI is sturdy, reconfigured, and simple to fabricate, consisting of a semi-spherical polymer cap added to the surface of the ferrule of a commercial single-mode fiber connector (SMF FC/PC) placed in front of a mirror at a proper distance. The length of the air cavity (Lair) was adjusted to equal the thickness of the polymer cap (Lpol) plus a distance δ to generate the most convenient Vernier effect spectrum. The DCFPI was packaged in a machined, movable mount that allows the adjustment of the air cavity length easily but also protects the polymer cap and simplifies the manipulation of the sensor head.

Hybrid Vernier effect: sensitivity amplification and two-parameter measurement in cascaded Fabry-Perot interferometer fiber sensor

Vernier effect enhances the sensitivity for interferometric fiber sensor, but indiscriminately amplifies cross-sensitivity to environmental parameters. Here, hybrid Vernier effect, a new theory based on the cascaded FPI, is proposed and demonstrated for cross-sensitivity elimination under the premise of sensitivity amplification. It combines traditional and high-order harmonic Vernier effects to measure two parameters simultaneously. The proposed sensor achieves strain sensitivity of 960.1 pm/µɛ, and temperature sensitivity of 1260.86 pm/°C. Stability experiments demonstrate excellent stability of envelope demodulation method, with minimum temperature resolution of 0.44 °C and minimum strain resolution of 0.58 µɛ. The proposed the hybrid Vernier effect can be achieved widely in common cascaded fiber FPI fiber sensor structure, making it good candidate for practical applications.

Liquid crystal-embedded fiber optic fabry perot temperature sensor based on Vernier effect

An optical temperature sensing method with ultra-high sensitivity and a wide measurement range is proposed. The performance enhancements come from the high thermos-optical coefficient of liquid crystal (LC) material, and the Vernier effect produced by LC birefringence characteristics. This paper proposes and demonstrates a method to enhance the measurement range of the LC temperature sensor. A miniature LC temperature sensor was made by using an optical fiber Fabry-Perot interferometer (FPI). To compensate for and attenuation of LC and improve the contrast of the FPI, silver films are coated on one end of the optical fiber. Due to the high birefringence of the LC in the interferometer, a Vernier spectrum can be observed in the reflection. The temperature measurement range of 20–32 °C and the temperature sensitivity of the Vernier peaks of a sensor sample is about 42.18 nm/°C, which is much higher than the sensitivity of the cascaded FBG in structure. The limited measurement range is due to the free spectral range (FSR) limitation. In this context, the FBG peak can be used as a temperature reference while switching the adjacent Vernier peaks. Hence, this LC temperature sensor exhibits high sensitivity as well as a wide measuring range, which would broaden the application scope of the LC temperature sensors.

Fiber laser strain sensor based on an optical phase-locked loop.

In this Letter, we present a high-strain resolution fiber laser-based sensor (FLS) by a novel optical phase-locked loop (OPLL) interrogation technique based on a root mean square detector (RMSD). The sensor consists of a distributed feedback (DFB) fiber laser as a master laser for strain sensing and a fiber Fabry-Perot interferometer (FFPI) as a reference. The laser carrier locks to the reference by the PDH technique, and the single sideband laser working as a slave laser locks to the DFB sensing element using the OPLL technique, respectively. A strain resolution of 8.19 pε/√Hz at 1 Hz and 35.5 pε in 10 s is achieved in the demonstrational experiments. Significantly, the noise behaves a 1∕f distribution below 0.2 Hz due to the very low pump power for the DFB sensor and an active thermostat testing environment. The proposed OPLL interrogation brings new thinking for the demodulation of FLS. This strain sensor based on FLS has a great performance in strain measurement and can be a powerful tool for geophysical research.

Multi-Point Optical Fiber Fabry-Perot Curvature Sensor Based on Microwave Photonics

This article reports a multi-point curvature sensor system based on multiplexed optical fiber Fabry-Perot interferometric (FPI) sensor devices and a microwave photonics interrogation technique. The FPI sensor is fabricated with the assistance of a capillary tube, where a short section of the capillary is sandwiched between two single-mode fibers, forming the air-gap Fabry-Perot cavity. Bending of the FPI device leads to changes in the fringe contrast of its reflection spectrum. Based on the microwave photonics filtering technique, variations of the fringe contrast are encoded into the changes in the peak magnitude of the passband in the frequency response of the FPI device. By multiplexing such FPI devices with different cavity lengths, multi-point measurements of curvature can be realized by tracking changes in corresponding passbands in the frequency response of the system. The FPI curvature sensor is easy-to-manufacture and cost-effective, and the microwave photonics-based system provides an alternative and robust solution to interrogating the multiplexed FPI sensors for multi-point curvature sensing that could be desired in structural health monitoring, human-machine interface sensing, and other related fields.

Fs-Laser Fabricated Miniature Fabry-Perot Interferometer in a No-Core Fiber for High-Temperature Applications.

This paper reports a fiber in-line Fabry-Perot interferometer (FPI) fabricated in a no-core fiber using the direct femtosecond laser writing technique for high-temperature sensing applications. Two in-line reflectors are directly inscribed in a no-core fiber to construct a low-finesse FPI. Fringe visibility greater than 10 dB is obtained from the reflection spectra of the fabricated no-core fiber FPIs. Temperature responses of a prototype no-core fiber FPI are characterized up to 1000 °C. The proposed configuration is compact and easy to fabricate, making it attractive for sensing applications in high-temperature harsh environments.

Versatile Optofluidic Fabry-Perot Sensor for Multiple Physical Parameters in Microfluidic Chips

An optofluidic sensor, which is composed of a fiber Fabry-Perot interferometer (FPI) and a microfluidic chip, is experimentally demonstrated to measure aerostatic pressure, local temperature, and fluidic flow rate in microfluidic chips. The aerostatic pressure sensitivity is as high as −2393.3 nm/Bar. By demodulating the aerostatic pressure and temperature with a sensitivity matrix, both the physical parameters can be predicted simultaneously. The noise-equivalent detection limit (NEDL) of aerostatic pressure is as low as 48.4 μBar. In addition, the experiment results show that the fluidic flow rate sensitivity is −1.8574 nm/(μl/min) and the NEDL of fluidic flow rate is 97.1 nl/min, respectively. The miniature optofluidic sensor based on the optical fiber Fabry-Perot interferometer provides a promising cost-effective sensing platform for monitoring multiple physical parameters in the microfluidic chips, which is of great significance for on-chip biochemical reactions.

Novel microspherical fiber Fabry–Pérot interferometer based on the Vernier effect for micro-displacement sensing

A novel optical fiber Fabry–Perot interferometer (FPI) based on the Vernier effect is proposed for micro-displacement sensing. The sensor is composed of an optical fiber microsphere and a section of multimode optical fiber with a flat end surface. The air cavity in the middle is used as the Fabry–Perot cavity. The extinction ratio of the reflection spectrum is significantly improved by the optical fiber microsphere, and the extinction ratio is ∼12 dB. First, a single FPI is tested for micro-displacement. A sensitivity of 2.13 nm/µm and linearity of 99.31% are obtained within the range of 0–1.872 µm via phase demodulation. The fabricated optical fiber FPI is used as the sensing arm and cascaded with the designed analog reference arm. The micro-displacement sensitivity of the sensing arm can be improved to 28.92 nm/µm through the Vernier effect, i.e., 13.58 times that of a single FPI. The fabricated sensor exhibits the characteristics of high sensitivity, contrast, and linearity; a compact structure; and low cost. It can be used for micro-displacement detection. In addition, the analog reference arm is unaffected by the environment, and it can freely adjust sensitivity magnification. Accordingly, it is applicable to micro-displacement detection scenarios under different sensitivity requirements.

High-Resolution Two-Degree-of-Freedom Displacement Measurement Based on Fiber Fabry–Perot Interferometer and Pound–Drever–Hall Technique

High-Resolution Two-Degree-of-Freedom Displacement Measurement Based on Fiber Fabry–Perot Interferometer and Pound–Drever–Hall Technique

Ultra-high sensitivity microwave-photonic sapphire fiber Fabry-Perot interferometry based on the Vernier effect.

The wavelength of microwave is longer than that of lightwave, causing the interferometric optical path difference induced by the measurand changes to be relatively smaller than that of microwave, which results in the lower sensitivity of sapphire fiber Fabry-Perot interferometer (FPI) sensor in microwave band. To improve sensitivity, a parallel FPI sensing system is constructed, in which a section of sapphire fiber connected to a single-mode transmission fiber is used as a sensing FPI, and a single-mode fiber (SMF) with a slightly different optical path from a sensing FPI is utilized as a reference FPI. By connecting two FPIs in parallel, Vernier effect is formed to improve sensitivity. The influence of relationship between the optical path difference of the reference FPI and the sensing FPI on the sensitivity amplification factor is analyzed based on the microwave interference spectrum of the parallel FPI. A section of sapphire fiber with the length of 8 cm is used as temperature sensor to construct high-temperature sensing system. The results demonstrate that the temperature sensitivity reaches about 2338.68kHz/°C, which is approximately 130 times higher than that of the sensing FPI alone. Furthermore, when the difference of optical path between the sensing FPI and the reference FPI is kept constant while the sensing FPI is unchanged, the amplification factor of the temperature sensitivity is approximately 2.64 times higher with longer length of the reference FPI compared to the situation with shorter length of the reference FPI.

Polymer transduction cavity based optical fiber Fabry-Perot interferometer for VOC sensing

Frequent exposure to volatile organic compounds (VOC) above the permissible limit can result in adverse health effects. Therefore, VOC detection and monitoring at trace levels are essential in both indoor and outdoor environments. A highly sensitive and accurate method is desired for this purpose and optical interferometry is a sensitive measurement technique useful for trace-level VOC sensing. We have fabricated and experimentally studied the sensing properties of the optical fiber Fabry–Perot interferometer polymer sensor cast on the fiber tip for acetone detection. Polystyrene, deposited at the end facet of the fiber act as the FP cavity. A significant shift in the interference pattern resonant dip positions is observed in the interaction of the FP cavity with acetone vapor due to changes in the properties of the polymer resulting in physical thickness variation and a change in refractive index. Emphasis has been put on studying the sensor performance over multiple measurement cycles to affirm the reproducibility of the results for repeated usage instead of one-time disposable measurements. Excellent repeatable sensing performance with a sensitivity of 5.78 pm/ppm is observed for 09 data sets recorded over 09 days consisting of 190 individual experimental studies.

High-sensitivity interferometric high-temperature strain sensor based on optical harmonic vernier effect

We present a fiber optic vernier harmonic sensor for simultaneous detection of temperature and strain in high temperature conditions based on a parallel dual fiber Fabry-Perot interferometers (FPI). Two air-cavity FPIs were assembled from SMF, MMF and a hollow silica tube (HST). A fiber Bragg grating (FBG) is inscribed in one of the arms of the Fabry-Perot interferometers (FPIs) for temperature compensation. Based on the fiber optic vernier harmonic effect, the strain sensitivity of the sensor is further increased to 178.75 pm/µε, with a good linear response to strain and temperature in the range of 24 ℃-900 ℃. And the fabrication is straightforward and economy. It is a potential tool for micro strain measurements under extreme high temperature conditions.

Hollow core fiber Fabry-Perot interferometers with reduced sensitivity to temperature: erratum.

In the original publication of our research article "Hollow core fiber Fabry-Perot interferometers with reduced sensitivity to temperature" [Opt. Lett.47, 2510 (2022)10.1364/OL.456589OPLEDP0146-9592], we identified an error that requires correction. The authors sincerely apologize for any confusion that may have arisen from this error. The correction does not affect the overall conclusions of the paper.