Fiber Crimp Research Articles

Fabrication of transparent glass fabric‐reinforced thermoplastic composite based on tow‐spreading technique

AbstractHighly transparent and mechanically robust thermoplastic composites have been developed by hot‐pressing PETG with E‐glass fabrics. The tow‐spreading technique facilitates the reduction of internal defects and fiber crimp angle in the composites, thereby significantly improving their optical and mechanical properties. The optimized composite containing 55.1 vol% glass fibers and 0.4 mm thickness has a high transmittance of 86.1%@616 nm and a low overall haze of 7.2%. Moreover, the 1 mm thick composites exhibit tensile strength of up to 340 MPa and impact strength of up to 86.3 kJ/m2. After 28 days of hygrothermal or UV aging, the composites show minimal changes in their glass transition temperature and thermal degradation temperature. The chemical structure also remains unchanged, with no observed crystallization. In comparison to UV aging, the composites demonstrate better resistance against hygrothermal aging. Specifically, the hygrothermal aged sample displayed a light transmittance retention rate of 93.5% and a bending strength retention rate of 94.3%, while these values were reduced to 73.3% and 90.5%, respectively, in the UV aged sample. The opto‐mechanical properties enhanced mechanism and aging degradation mechanism have been identified by microscopic morphological observation. This work provides an innovative and straightforward approach to fabricate transparent, recyclable, high‐strength thermoplastic composites.Highlights Highly transparent, mechanically robust, recyclable glass‐fabric reinforced thermoplastic composites are fabricated. Composites with spread‐tow fabrics exhibits improved transparency. The fabrication route is scalable and cost‐effective. The mechanism for opto‐mechanical properties enhancement are proposed.

A Mathematical Model for Postimplant Collagen Remodeling in an Autologous Engineered Pulmonary Arterial Conduit.

This study was undertaken to develop a mathematical model of the long-term in vivo remodeling processes in postimplanted pulmonary artery (PA) conduits. Experimental results from two extant ovine in vivo studies, wherein polyglycolic-acid (PGA)/poly-L-lactic acid tubular conduits were constructed, cell seeded, incubated for 4 weeks, and then implanted in mature sheep to obtain the remodeling data for up to two years. Explanted conduit analysis included detailed novel structural and mechanical studies. Results in both studies indicated that the in vivo conduits remained dimensionally stable up to 80 weeks, so that the conduits maintained a constant in vivo stress and deformation state. In contrast, continued remodeling of the constituent collagen fiber network as evidenced by an increase in effective tissue uniaxial tangent modulus, which then stabilized by one year postimplant. A mesostructural constitute model was then applied to extant planar biaxial mechanical data and revealed several interesting features, including an initial pronounced increase in effective collagen fiber modulus, paralleled by a simultaneous shift toward longer, more uniformly length-distributed collagen fibers. Thus, while the conduit remained dimensionally stable, its internal collagen fibrous structure and resultant mechanical behaviors underwent continued remodeling that stabilized by one year. A time-evolving structural mixture-based mathematical model specialized for this unique form of tissue remodeling was developed, with a focus on time-evolving collagen fiber stiffness as the driver for tissue-level remodeling. The remodeling model was able to fully reproduce (1) the observed tissue-level increases in stiffness by time-evolving simultaneous increases in collagen fiber modulus and lengths, (2) maintenance of the constant collagen fiber angular dispersion, and (3) stabilization of the remodeling processes at one year. Collagen fiber remodeling geometry was directly verified experimentally by histological analysis of the time-evolving collagen fiber crimp, which matches model predictions very closely. Interestingly, the remodeling model indicated that the basis for tissue homeostasis was maintenance of the collagen fiber ensemble stress for all orientations, and not individual collagen fiber stresses. Unlike other growth and remodeling models that traditionally treat changes in the external boundary conditions (e.g., changes in blood pressure) as the primary input stimuli, the driver herein is changes to the internal constituent collagen fiber themselves due to cellular mediated cross-linking.

Influence of Reinforcement Architecture on Behavior of Flax/PLA Green Composites under Low-Velocity Impact.

The main goal of this study is the comparison of different reinforcement architectures on the low-velocity impact behavior of green composites. The study includes the comparison of unidirectional, basket weave, and twill weave flax/PLA composites, they are subjected to unidirectional tensile tests, drop-weight impact tests, and after-impact compression tests. Results show that the unidirectional composite demonstrates superior tensile strength and initial modulus due to reduced fiber crimp, while basket weave exhibits the highest energy absorption capability and strain capacity attributed to its higher fiber-weight ratio and fiber crimp. Unidirectional composite also shows a larger impacted damage area compared to basket weave and twill weave, attributed to its internal architecture. Residual compressive strength across all composites decreased by 40% compared to the reference sample. However, the reduction in stiffness after impact was different, UD/PLA composite stiffness was reduced by 30% while the reduction in BW/PLA and T/PLA composites was about 20%.

Whole genome sequencing analysis of alpaca suggests TRPV3 as a candidate gene for the suri phenotype

BackgroundAlpaca is a domestic South American camelid probably arising from the domestication of two wild camelids, the vicugna and the guanaco. Two phenotypes are described for alpaca, known as huacaya and suri. Huacaya fleece is characterized by compact, soft, and highly crimped fibers, while suri fleece is longer, straight, less crimped, and lustrous. The gene variants determining these phenotypes are still unknown, although previous studies suggested a dominant inheritance of the suri. Based on that, the aim of this study was the identification of the gene variants determining alpaca coat phenotypes through whole genome sequencing (WGS) analysis.ResultsThe sample used includes two test-cross alpaca families, suri × huacaya, which produced two offspring, one with the suri phenotype and one with the huacaya phenotype. The analyzed sample was expanded through the addition of WGS data from six vicugnas and six guanacos; this because we assumed the absence of the gene variants linked to the suri phenotype in these wild species. The analysis of gene variant segregation with the suri phenotype, coupled with the filtering of gene variants present in the wild species, disclosed the presence in all the suri samples of a premature termination codon (PTC) in TRPV3 (transient receptor potential cation channel subfamily V member 3), a gene known to be involved in hair growth and cycling, thermal sensation, cold tolerance and adaptation in several species. Mutations in TRPV3 were previously associated with the alteration of hair structure leading to an impaired formation of the hair canal and the hair shaft in mouse. This PTC in TRPV3, due to a G > T substitution (p.Glu475*), results in a loss of 290 amino acids from the canonical translated protein, plausibly leading to a physiological dysfunction.ConclusionThe present results suggest that the suri phenotype may arise from a TRPV3 gene variant which may explain some of the suri features such as its longer hair fibre with lower number of cuticular scales compared to huacaya.

Methodological Aspects and Mesh Convergence in Numerical Analysis of Athermal Fiber Network Material Deformation

A balance between model complexity, accuracy, and computational cost is a central concern in numerical simulations. In particular, for stochastic fiber networks, the non-affine deformation of fibers, related non-linear geometric features due to large global deformation, and size effects can significantly affect the accuracy of the computer experiment outputs and increase the computational cost. In this work, we systematically investigate methodological aspects of fiber network simulations with a focus on the output accuracy and computational cost in models with cellular (Voronoi) and fibrous (Mikado) network architecture. We study both p and h-refinement of the discretizations in finite element solution procedure, with uniform and length-based adaptive h-refinement strategies. The analysis is conducted for linear elastic and viscoelastic constitutive behavior of the fibers, as well as for networks with initially straight and crimped fibers. With relative error as the determining criterion, we provide recommendations for mesh refinement, comment on the necessity of multiple realizations, and give an overview of associated computational cost that will serve as guidance toward minimizing the computational cost while maintaining a desired level of solution accuracy.

Using recycled plastic waste as fiber reinforcement on limestone residue mortar

The main purpose of the paper is to study the effect of the geometry of recycled plastic fiber on the performance of mortar basing on natural limestone residue. The used fibers were collected from plastic waste of polypropylene, resulting from domestic sweeps fabrication. Two types of recycled fibers were used, straight and crimped fibers, which have the same length (20 ± 2 mm) and the same diameter (0.45 ± 0.07 mm). Four dosages of fibers were considered, 0.5, 1, 1.5 and 2 wt. %. The obtained results show that the geometry of recycled plastic fibers has an important effect on the performances of limestone residue mortar. The addition of recycled fibers to mortar decreases its workability and the decrease is higher with crimped fibers. The results revealed that the limit dosage of recycled plastic fiber necessary to obtain a workable mortar is 1 % and 0.5 % for straight and crimped fibers, respectively. The benefit of recycled plastic fibers is well observed on the flexural and compressive behavior of limestone residue mortar, but the strength’s values are higher in straight fibers mortar (SFM) than that in crimped fibers mortar (CFM). The microstructure analysis confirms the good performances of the fiber mortar.

Preparation of Self-Curling Melt-Blown Fibers with Crimped Masterbatch (CM) and Its Application for Low-Pressure Air Filtration.

Particulate matter (PM) and airborne viruses pose significant threats to both the environment and public health. As the most viable solution to prevent the inhalation of these pollutants, there is an urgent demand for face masks with excellent filtration efficiency and low-pressure drop. In this study, a crimped masterbatch (CM) is added to polypropylene feedstocks to produce curling fibers through melt-blown spinning. These curled fibers exhibit low filtration resistance and effective dust-holding performances when used for air filtration. The effect of adding CM on fiber diameter, pore size, crimp, porosity, roughness, and surface potential was studied. The filtration performance of the materials, including the PM filtration capabilities, recirculation filtration, and loading test performance, were also investigated. The results demonstrate that the degree of fiber crimp can be adjusted by incorporating varying amounts of CM. This curling was caused by the uneven shrinkage that occurred due to variations in thermal contraction between these polymers. The curled fibers created a fluffy structure in the fiber network and modified the distribution of pore sizes within it. Under the same filtration conditions as sodium chloride aerogel, CM-2 (PP:CM 8:2) exhibited similar filtration efficiency (95.54% vs. 94.74%), lower filtration resistance (88.68 Pa vs. 108.88 Pa), higher quality factor (0.035 Pa-1 vs. 0.028 Pa-1) and better dust holding capacity (10.39 g/m2 vs. 9.20 g/m2) compared to CM-0 (PP:CM 10:0). After 30 days of indoor storage, the filtration efficiency of CM-2 remained above 94%. The self-curling melt-blown filtration material developed here could potentially be applied in the field of protective masks.

Effect of Steel Fibers on the Properties of Refractory Free Cement Concrete

Free cement refractory concrete is a type of refractory concrete with replacing alumina cement by bonding materials such as white kaolin, red kaolin and fumed silica. The free cement refractory concrete used in many applications like Petrochemicals, iron furnaces and cement production industries. The research clarifies the effect of steel fibers with two types crimped steel fibers and hooked steel fibers with percentages 0.5%, 1% and 1.5% by volume from weight of bauxite aggregates. The additions of steel fibers with two types gave good properties in high temperatures where the specimens keep the dimension without failure and the properties made the best. the percentage of increasing for thermal conductivity was 44% for 1.5% crimped fibers and 42.8% for 1.5% hooked end fibers and the percentage increasing in bulk density of free cement refractory concrete was 30% for 1.5% crimped fibers and 27% for 15% hooked end fibers . From this study can be concluded that the best types of steel fibers which used in free cement refractory concrete is the crimped type with percentage 1.5%.

Microstructural and damage parameter effect analysis on the failure mechanism of fibrous soft tissues with a structure-based unit cell model

The presence of hierarchical microstructures in natural materials, such as connective tissues, makes them possess exceptional mechanical performance and undergo complex damage behaviors. Accordingly, in this study, a structure-based unit cell model (UCM) in which controllable irregular crimped fiber is embedded into soft matrix is constructed for the analysis of microstructural effects. An anisotropic hyperelastic constitutive model enhanced with different damage parameters is applied in finite element program, and the effects of damage parameters on the mechanical responses of fibrous soft tissues are investigated. The numerical results indicate that the fiber waviness plays a significant role in determining the stiffness of the tissues and that the microstructure controlled by the fiber crimp amplitude H, waviness χ and number of inflection points ω, mainly determines the fluctuation of the nominal stress–strain curves of these tissues with damaged fibers. In addition, a damage parameter analysis indicates that the attenuation of the strength and amplitude of the stress strongly depend on the strain energy limiter, and the parameter m mainly determines the rate of damage accumulation by the fibers with smaller strain energy limiters. The results of this study deepen the understanding of the mechanical behaviors of such fibrous soft tissues and provides a template for the optimization of structural and material designs for bioinspired composites.

Who bears the load? IOP-induced collagen fiber recruitment over the corneoscleral shell

Collagen is the main load-bearing component of cornea and sclera. When stretched, both of these tissues exhibit a behavior known as collagen fiber recruitment. In recruitment, as the tissues stretch the constitutive collagen fibers lose their natural waviness, progressively straightening. Recruited, straight, fibers bear substantially more mechanical load than non-recruited, wavy, fibers. As such, the process of recruitment underlies the well-established nonlinear macroscopic behavior of the corneoscleral shell. Recruitment has an interesting implication: when recruitment is incomplete, only a fraction of the collagen fibers is actually contributing to bear the loads, with the rest remaining “in reserve”. In other words, at a given intraocular pressure (IOP), it is possible that not all the collagen fibers of the cornea and sclera are actually contributing to bear the loads.To the best of our knowledge, the fraction of corneoscleral shell fibers recruited and contributing to bear the load of IOP has not been reported. Our goal was to obtain regionally-resolved estimates of the fraction of corneoscleral collagen fibers recruited and in reserve. We developed a fiber-based microstructural constitutive model that could account for collagen fiber undulations or crimp via their tortuosity. We used experimentally-measured collagen fiber crimp tortuosity distributions in human eyes to derive region-specific nonlinear hyperelastic mechanical properties. We then built a three-dimensional axisymmetric model of the globe, assigning region-specific mechanical properties and regional anisotropy. The model was used to simulate the IOP-induced shell deformation. The model-predicted tissue stretch was then used to quantify collagen recruitment within each shell region. The calculations showed that, at low IOPs, collagen fibers in the posterior equator were recruited the fastest, such that at a physiologic IOP of 15 mmHg, over 90% of fibers were recruited, compared with only a third in the cornea and the peripapillary sclera. The differences in recruitment between regions, in turn, mean that at a physiologic IOP the posterior equator had a fiber reserve of only 10%, whereas the cornea and peripapillary sclera had two thirds. At an elevated IOP of 50 mmHg, collagen fibers in the limbus and the anterior/posterior equator were almost fully recruited, compared with 90% in the cornea and the posterior sclera, and 70% in the peripapillary sclera and the equator. That even at such an elevated IOP not all the fibers were recruited suggests that there are likely other conditions that challenge the corneoscleral tissues even more than IOP. The fraction of fibers recruited may have other potential implications. For example, fibers that are not bearing loads may be more susceptible to enzymatic digestion or remodeling. Similarly, it may be possible to control tissue stiffness through the fraction of recruited fibers without the need to add or remove collagen.

Crimped fiber composites: mechanics of a finite-length crimped fiber embedded in a soft matrix.

Composites comprising crimped fibers of finite length embedded in a soft matrix have the potential to mimic the strain-hardening behavior of tissues containing fibrous collagen. Unlike continuous fiber composites, such chopped fiber composites would be flow-processable. Here, we study the fundamental mechanics of stress transfer between a single crimped fiber and the embedding matrix subjected to tensile strain. Finite element simulations show that fibers with large crimp amplitude and large relative modulus straighten significantly at small strain without bearing significant load. At large strain, they become taut and hence bear increasing load. Analogous to straight fiber composites, there is a region near the ends of each fiber which bears much lower stress than the midsection. We show that the stress-transfer mechanics can be captured by a shear lag model where the crimped fiber can be replaced with an equivalent straight fiber whose effective modulus is lower than that of the crimped fiber, but increases with applied strain. This allows estimating the modulus of a composite at low fiber fraction. The degree of strain hardening and the strain needed for strain hardening can be tuned by changing relative modulus of the fibers and the crimp geometry.

Assessing Crimp of Fibres in Random Networks with 3D Imaging.

The analysis of fibrous structures using micro-computer tomography (µCT) is becoming more important as it provides an opportunity to characterise the mechanical properties and performance of materials. This study is the first attempt to provide computations of fibre crimp for various random fibrous networks (RFNs) based on µCT data. A parametric algorithm was developed to compute fibre crimp in fibres in a virtual domain. It was successfully tested for six different X-ray µCT models of nonwoven fabrics. Computations showed that nonwoven fabrics with crimped fibres exhibited higher crimp levels than those with non-crimped fibres, as expected. However, with the increased fabric density of the non-crimped nonwovens, fibres tended to be more crimped. Additionally, the projected fibre crimp was computed for all three major 2D planes, and the obtained results were statistically analysed. Initially, the algorithm was tested for a small-size, nonwoven model containing only four fibres. The fraction of nearly straight fibres was computed for both crimped and non-crimped fabrics. The mean value of the fibre crimp demonstrated that fibre segments between intersections were almost straight. However, it was observed that there were no perfectly straight fibres in the analysed RFNs. This study is applicable to approach employing a finite-element analysis (FEA) and computational fluid dynamics (CFD) to model/analyse RFNs.

Bionic artificial penile Tunica albuginea

Bionic artificial penile Tunica albuginea

Displacement recovery and energy dissipation of crimped NiTi SMA fibers during cyclic pullout tests

Abstract This study examines the cyclic pullout behavior of two types of cold-drawn NiTi shape memory alloy fibers, such as paddled and crimped fibers. For this, two diameters of 1.0 and 0.7 mm are considered. The experimental cyclic pullout results show that the deep crimped fibers produce a higher maximum pullout resistance than the shallow crimped fibers. When heated, the shallow crimped fiber increases the diameter more significantly than the deep crimped fiber, whereas the fiber wave depth decreases more than the deep crimped fiber. Thus, the maximum pullout resistance increases for the heated shallow crimped fiber and decreases for the heated deep crimped fiber. The displacement recovery ratio (DRR) reduction with an increasing slip is significant for the fiber with a low anchoring bond. The high anchoring bond fiber also introduces a higher average DRR than the fiber with a relatively low anchoring bond. Under heating treatment, the average DRR increases due to the prestressing in the fiber due to the shape memory effect. However, the anchoring bond of the fiber is enough to produce prestressing in the fiber. The anchoring bond of the fiber and the prestressing also influence the energy dissipation (ED). The higher anchoring bond results in a higher ED value, and the prestressing in the fiber contributes more to the increased ED values.

Fluorescent labeling with 5-DTAF reduces collagen fiber uncrimping in loaded tendons

A fluorescent dye commonly used to image tissues under load (5-DTAF) has previously been shown to stiffen tendons. This study hypothesized that 5-DTAF staining stiffens tendons through reduced fiber sliding, altering the rate at which crimped collagen fibers straighten under load. This was tested by using reflected cross-polarized light microscopy to measure fiber crimp period of cervine extensor digitorum longus tendon specimens under axial load. Specimens were treated with either phosphate buffered saline (negative control), genipin (positive control), or 5-DTAF. In saline treated specimens, crimp period (relative to unstretched) increased at approximately 2.5 times the applied axial strain, indicating substantial fiber sliding. In both 5-DTAF and genipin treated specimens, this ratio was reduced to 1:1, indicating no fiber sliding. These results add further evidence that care should be taken when using 5-DTAF to stain tissue for studying microscale deformations in tissues.

Effect of axial yarn distribution on the progressive damage behavior of braided composite tube subjected to three-point bending

The effect of axial yarns on progressive bending damage of braided composite tubes is studied in this paper. Four specimens with different number and distribution of axial yarns were experimentally tested by quasi-static three-point bending. At the same time, infrared thermography was used to observe the damage in-situ. Combined with the cross-section morphology of Ultra-Depth 3D Microscope, the damage evolution and distribution characteristics of braided tubes were identified. It is found that axial yarns enhance the mechanical properties of braided composite tube. The detected changes of infrared maximum temperature have a good correlation with the damage initiation and failure mechanism of the specimen. The abrupt changes of the maximum temperature indicate the occurrence of local fiber breakage, especially the axial yarn breakage. If there are axial yarns on the compression side of the tube, the maximum temperature increases by 0.5 °C in the linear elastic stage, and two initial damages of debonding and fiber breakage will occur. The debonding started at the interface of the axial yarn. The axial yarns increased fiber crimp, resulting in obvious wavy delamination between layers of the specimen, and the axial damage range was expanded. In addition, the mixed structure with axial yarns only on the compression side can inhibit the damage from spreading down the braided tube wall.

An analytical approach to study the loading behavior of hollow fibers under negative pressure and atmospheric pressure

Hollow fibers have been widely used as important components of membranes for drug delivery in the medical field. However, their usages in environmental and agricultural aspects have not been commonly unearthed. In our previous research, a new drug delivery system was established by utilizing hollow fiber as a carrier to convey medical substances in different phases, respectively. Our current research aims to expand the application of hollow fibers apart from medicine. In this study, the loading efficiency of the liquid under standard atmospheric pressure (nonvacuum) and negative pressure (vacuum) were further examined to achieve a higher loading system. The physical properties and the loading abilities of the three types of hollow fibers including original short crimped fibers, fibers from roving yarns, and fibers from spun yarns were studied and discussed. In-depth investigations of loading efficiency, wicking performance, water absorption, and thermal conductivity were conducted. Higher loading efficiency was observed by adopting the method of vacuum under negative pressure resulting from all experiments of which the result was at least 15 times higher than the nonvacuum-loaded methods. It was also at least 0.25% greater in moisture content, almost two times larger in the water absorption rate for yarn samples, and 35% higher for fabric samples. The differences in thermal conductivity within the two conditions were 0.00016 W/cm°C. Using the vacuum approach can improve the overall performance of precise liquid loading, increasing the efficiency and thereby reduce the production costs. It is believed to bring high-value advantages in agricultural aspects such as for sustainable pest control and crop growth.

Strain Measures and Energies for Crimped Fibres and Novel Analytical Expressions for Fibre Populations: Ingredients for Structural Fibre Network Models

This paper deals with the structural modelling of fibre networks with a focus on the description of populations of initially crimped fibres. It presents a systematic approach of introducing appropriate strain measures for single fibres based on a deformation decomposition and by transferring knowledge from the field of elastoplasticity. On this basis, for example, the often used Biot-type fibre strain measures lambda-lambda_{mathrm{w}} and lambda /lambda _{mathrm{w}}-1, with stretch lambda and waviness lambda _{mathrm{w}}, are consistently assigned to different classes of material strain (“additive”) or intermediate strain (“multiplicative”) descriptions, respectively. We review in this work different fibre strain energies based on the different stain measures and present extensive comparisons on the physical implications and the results on the fibre population and network scale. These investigations also include formulations with a Hencky-type energy based on a logarithmic strain. Furthermore, we present novel analytical expressions for fibre populations that make the evaluation of integral expression superfluous and thus lead to a significant reduction in computational time.

A Review: “Experimental Study on Steel Fiber Reinforced Concrete Using flat Crimped & Round Crimped Type Steel Fiber.”

Abstract: Steel Fibre Reinforced Concretes are characterized by high tensile and flexural strengths and high ductility, as well as by a high compressive strength and a very good workability. Ductility and strength of concrete can be improved at lower fiber contents, where fibers are used in combination rather than reinforcement with a single type of fiber. Durability problems concerning one type of fiber may be offset with the presence of a second type of fiber. Steel Fiber is added by 1% volume of concrete. The different concrete mixesalong with control mix proportions as 100% round crimped type fiber, 50% round crimped type fiber -50% flat crimped type fiber and 100% flat crimped type fiber. Two types of crimped steel fiber i.e. round crimped type steel fiber and flat crimped steel fiber are used of length having 50mm. An extensive experimental investigation consisting of 12 specimen of size 50 x 10 x 10cm for determining flexural strength, 12 specimen for compressive strength and 12 specimen for split end test are used.In the experiment, an combination of steel fibre with concrete is used, which improved various mechanical properties and the strength. This review study is a trial of givingsome highlights for inclusion of steel fibers especially in terms of using them with new mix ratio combinations with concrete.

Concurrent multiscale modeling of in-plane micro-damage evaluation in Z-pinned composite laminates

Most of the unit cell models for Z-pinned composite laminates (ZCL) are mesoscopic in scale, where the fiber reinforced zone is modeled as homogeneous but without detailed characterization and failure analysis of the fibers and matrix. This paper proposes a new concurrent multiscale unit cell model to investigate the in-plane micro-damage evolution of ZCL. The novelty worth mentioning is the proposed element-based method to generate random microbuckling spatial fibers in the fiber reinforced zone, where the microbuckling is caused by fiber waviness and fiber crimp, and then the mesh of fiber, Z-pin, matrix, and the interface between Z-pin and matrix is regenerated. In-plane tensile tests (ASTM D3039) are conducted for verification. There is good agreement between experiment and simulation, only with deviations of −0.97% and 2.69% for tensile modulus and fracture initiation stress, respectively. The research indicates that in-plane micro-damage initiates from the interface between Z-pin and matrix. The stress concentration and higher local fiber volume fraction, caused by the microbuckling spatial fibers clustered near the Z-pin, play a major role in the evolution of interface damage, crack initiation and growth.