Scanning Electrochemical Microscopy In Feedback Mode Research Articles

Effect of Redox Mediators on Corrosion Behavior and Scanning Electrochemical Microscopy Response.

Scanning electrochemical microscopy (SECM) is widely used to measure local electrochemical reactivity of corroding surfaces. A major criticism of using SECM in feedback mode for corrosion studies is the requirement of an external redox mediator (RM) as it could react with the metal and affect the Nernst potential at the metal-solution interface. Consequently, it becomes challenging to differentiate the interference caused by the RM from the local reactivity of the metal. Herein, a multiscale electrochemical approach is presented to investigate the effect of RM choice on the corroding substrate. Two common RMs, ferrocenemethanol and hexaammineruthenium(III) chloride, were used to perform SECM over copper and aluminum. It was found during macroscale electrochemical measurements that Ru(NH)63+ acted as an oxidant and promoted corrosion. The SECM feedback behavior varied for copper depending on the RM used, suggesting that the corrosion reactions controlled the negative feedback mechanism, not the formation of an insulating passive film. The passivated aluminum surface consistently exhibited negative feedback, regardless of the RM used. SECM approach curves also displayed a distortion in the steady state current, which was caused by the deposition of substrate-generated species on the microelectrode. These deviations in feedback response were accounted for during analysis through incorporation into a finite element model to accurately extract the RM kinetic rate constants. The importance of understanding these processes is highlighted to avoid misinterpretation of passive behavior and advances toward a more quantitative use of SECM for corrosion studies.

Simultaneous Scanning Ion Conductance and Electrochemical Microscopy in Lithium‐Ion Battery Research

AbstractDeeper understanding of processes involved in operation of lithium‐ion batteries (LIBs) is necessary to further optimize them for future applications. Extensive research was conducted on the formation of a solid electrolyte interphase (SEI) on negative battery electrodes, still leaving several questions unanswered. Scanning probe microscopies (SPMs) enable in situ and operando investigations and have the potential to explain some phenomena. Scanning electrochemical microscopy (SECM) and scanning ion conductance microscopy (SICM) could be employed in LIB studies. A novel SICM method based on the redox couple ferrocene/ferrocenium is introduced for applications in carbonate solvents widely used in LIBs. Proof of concept measurements were conducted with a micro milled copper circuit board as model substrate. Furthermore, the proposed SICM approach was hyphenated with feedback mode SECM resulting in the simultaneous mapping of morphology and electrochemical activity. A flexible dual‐probe arrangement was developed enabling usage of both SPM techniques at the same time, and furthermore, an easy replacement of both individual probes if needed. The setup was applied in the characterisation of commercial graphite electrodes for LIBs before and after conducting a pre‐charging protocol. Changes in electrochemical activity and topography of the graphite electrode were resolved in simultaneously generated SECM/SICM recordings.

Local Degradation of PEDOT:PSS on Silicon Nanostructures Using Scanning Electrochemical Microscopy.

Conducting polymers show attractive characteristics as electrode materials for micro-electrochemical energy storage (MEES). However, there is a lack of characterization techniques to study conjugated/conducting polymer-based nanostructured electrodes. Here, scanning electrochemical microscopy (SECM) is introduced as a new technique for in situ characterization and acceleration of degradation processes of conducting polymers. Electrodes of PEDOT:PSS on flat silicon, silicon nanowires (SiNWs) and silicon nanotrees (SiNTrs) are analyzed by SECM in feedback mode with approach curves and chronoamperometry. The innovative degradation method using SECM reduces the time required to locally degrade polymer samples to a few thousand seconds, which is significantly shorter than the time usually required for such studies. The degradation rate is modeled using Comsol Multiphysics. The model provides an understanding of the phenomena that occur during degradation of the polymer electrode and describes them using a mathematical constant A0 and a time constant τ.

Electrocatalytic Metallic Nanostructures Prepared By Electrorefining and Cathodic Corrosion

Metallic nanostructures (NS) due to their unique properties are often used as electrocatalytic electrode materials in energy conversion and storage as well as in sensing applications. Their common methods of preparation involve homogeneous synthesis and electrodeposition from solutions containing appropriate precursor and often reducing agent and capping agent (surfactant). The main drawbacks of these methods are restricted yield, waste production and often intrinsic contamination of the surface of obtained NS. Moreover, surface capping ligands affect electrocatalytic activity by hindrance of reactant access to the active sites.We propose a versatile method of preparation of bare (non-capped) mono- and multi-metallic (Au,1 Cu,2 Ag, Fe) NS by localized electrorefining of polycrystalline raw metals at high efficiency in a controlled manner. Catalytic activities of obtained NS towards oxygen reduction reaction (ORR) in alkaline media, hydrogen evolution (HER) and carbon dioxide reduction (CO2RR) to easily electrooxidizable fuels (formic acid and carbon monooxide) were analyzed by feedback mode scanning electrochemical microscopy (SECM). The morphology and specific activity of obtained NS depend on used support material (indium tin oxide (ITO) and glassy carbon) and other electrorefining parameters such as electrodeposition potential, source velocity and the composition of the electrolyte. The last parameter determines stoichiometry of Faradaic processes. Both gold and copper electrooxidation and electroreduction can follow one electron stoichiometry. ORR in alkaline media and CO2RR occur effectively on NS with highly developed surfaces, containing large number of defects, corners and edges, whereas HER occurs efficiently at crystallographic Cu facets. Bare gold NS also exhibit outstanding plasmonic properties. They were applied as support for surface-enhanced Raman spectroscopy (SERS) of single molecules providing enhancement factor >106.1 Another method of preparation of metallic nanostructures is cathodic corrosion. This approach for platinum was studied by Koper group.3 We used this procedure for platinum ultramicroelectrode treatment. Obtained Pt NS exhibit unique catalytic properties towards electrooxidation of glucose.

Combined AFM/SECM Investigation of the Solid Electrolyte Interphase in Li‐Ion Batteries

AbstractThe solid electrolyte interphase (SEI) is an electronically insulating film formed from the decomposition of the organic electrolyte at the surface of the negative electrodes in Li‐ion batteries (LIBs). This film is of vital importance in the performance and safety of LIBs. Atomic force microscopy (AFM) and scanning electrochemical microscopy (SECM) are combined in one platform for the consecutive in situ investigation of surface reactions in LIBs inside an Ar‐filled glovebox. As proof of concept, the formation and the electrochemical properties of the SEI formed on glassy carbon electrodes are investigated. Changes in topography during film formation of the SEI are studied via AFM. The AFM tip is then used to partially remove a small area (50×50 μm2) of the SEI, which is subsequently probed using SECM in feedback mode. The AFM‐scratched spot is clearly visualized in the SECM image, demonstrating the strength of the AFM/SECM combination for the investigation in the field of LIBs.

Multifunctional carbon nanoelectrodes fabricated by focused ion beam milling

We report a strategy for fabrication of sub-micron, multifunctional carbon electrodes and application of these electrodes as probes for scanning electrochemical microscopy (SECM) and scanning ion conductance microscopy (SICM). The fabrication process utilized chemical vapor deposition of parylene, followed by thermal pyrolysis to form conductive carbon and then further deposition of parylene to form an insulation layer. To achieve well-defined electrode geometries, two methods of electrode exposure were utilized. In the first method, carbon probes were masked in polydimethylsiloxane (PDMS) to obtain a cone-shaped electrode. In the second method, the electrode area was exposed via milling with a focused ion beam (FIB) to reveal a carbon ring electrode, carbon ring/platinum disk electrode, or carbon ring/nanopore electrode. Carbon electrodes were batch fabricated (~35/batch) through the vapor deposition process and were characterized with scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM), and cyclic voltammetry (CV) measurements. Additionally, Raman spectroscopy was utilized to examine the effects of Ga(+) ion implantation, a result of FIB milling. Constant-height, feedback mode SECM was performed with conical carbon electrodes and carbon ring electrodes. We demonstrate the utility of carbon ring/nanopore electrodes with SECM-SICM to simultaneously collect topography, ion current and electrochemical current images. In addition, carbon ring/nanopore electrodes were utilized in substrate generation/tip collection (SG/TC) SECM. In SG/TC SECM, localized delivery of redox molecules affords a higher resolution, than when the redox molecules are present in the bath solution. Multifunctional geometries of carbon electrode probes will find utility in electroanalytical applications, in general, and more specifically with electrochemical microscopy as discussed herein.

Use of Catechol As Selective Redox Mediator in Scanning Electrochemical Microscopy Investigations

The use of catechols, and more specifically of dopamine, as a specific redox mediator for scanning electrochemical microscopy (SECM) investigations was evaluated in the challenging situation of an ultrathin layer deposited on a conductive substrate (carbon materials). Experiments show that dopamine is a well-adapted redox system for SECM in feedback mode and in unbiased conditions. Used as a redox mediator, catechol permits the investigations of modified surfaces without an electrical connection of the sample thanks to fast charge transfer kinetics but with a surface selectivity that does not exist in classical outer-sphere redox mediators. The interest of catechol in SECM as a sensitive redox mediator is exemplified by monitoring several modification steps of an ultrathin (<1 nm) hierarchically porous organic monolayer deposited on carbon substrates. For quantitative analysis, the SECM approach curves using dopamine could simply be characterized with an irreversible electron transfer kinetics model in a large range of pH.

Combining Scanning Electrochemical Microscopy with Infrared Attenuated Total Reflection Spectroscopy for in Situ Studies of Electrochemically Induced Processes

The combination of scanning electrochemical microscopy (SECM) with single-bounce attenuated total reflection Fourier-transformed infrared spectroscopy (FT-IR-ATR) has been developed for in situ studies on electrochemically induced processes at IR waveguide surfaces via evanescent field absorption spectroscopy. The feasibility of the combined microelectrochemical FT-IR setup was demonstrated by spectroscopically monitoring microstructured polymer depositions induced via feedback mode SECM using a 25 mum Pt disk ultramicroelectrode (UME). The surface of a ZnSe ATR crystal was initially coated with 2,5-di-(2-thienyl)-pyrrole (SNS) layer, which was then locally polymerized during Ru(bpy)(3)(2+) mediated feedback mode SECM experiments. The polymerization reaction was simultaneously monitored by recording absorption intensity changes of SNS specific IR bands, thereby providing information on the polymerization mechanism and on the percentage of surface modification.

Feedback mode SECM study of laccase and bilirubin oxidase immobilised in a sol–gel processed silicate film

Thin silicate films with immobilised enzymes catalysing dioxygen reduction, i.e. laccase and bilirubin oxidase (BOD), were deposited on glass and poly(methyl 2-methylpropenoate) (Plexiglas) surfaces in a sol-gel process by sol drop evaporation. Scanning electrochemical microscopy (SECM) images and approach curves were recorded using hexacyanoferrate(iii) as mediator in the feedback mode. Confocal laser scanning microscopy (CLSM) images in the reflection mode showed larger film thickness close to the edge of the film and laccase aggregates within the film. SECM images obtained using different dioxygen concentrations showed that the film edge and laccase aggregates exhibit higher enzymatic activity towards dioxygen reduction. SECM current-distance curves enabled the determination of kinetic information at the particular regions of the samples after numerical fitting of model parameters. The heterogeneous first order rate constant at the film border was estimated to be ca. 19 times higher than the value obtained when approaching to the centre of the film. The reason of higher laccase surface concentration at the film edge is carefully discussed. For comparison of laccase and BOD activities, silicate spots of 50 microm diameter were deposited on a single Plexiglas sample and examined using SECM. BOD exhibits much higher activity especially at neutral pH.

Optimized Preparation and Scanning Electrochemical Microscopy Analysis in Feedback Mode of Glucose Oxidase Layers Grafted onto Conducting Carbon Surfaces

An optimized immobilization procedure based on the electroreduction of aryldiazonium salt followed by covalent attachment of a cross-linked hydrogel was used to graft glucose oxidase on a carbon surface. Scanning electrochemical microscopy (SECM) and cyclic voltammetry were used to follow the construction steps of the modified electrode. By adjusting the compactness of the layer through the electrografting reaction, the penetration of the mediator through the layer can be controlled to allow the monitoring of the enzymatic activity by both cyclic voltammetry and SECM in feedback mode. The enzymatic activity of the film is finally characterized by SECM.

Scanning Electrochemical Microscopy with Slightly Recessed Nanotips

Slightly recessed nanoelectrodes were prepared by controlled etching of nanometer-sized, flat Pt electrodes. By using high-frequency (e.g., 2 MHz) ac voltage, the layer of Pt as thin as greater, approximately >3 nm was removed to produce a cylindrical cavity inside the insulating glass sheath. The etched electrodes were characterized by combination of voltammetry and scanning electrochemical microscopy (SECM) to determine the radius and the effective depth of the recess. The theory was developed for current versus distance curves obtained with a recessed tip approaching either a conductive or an insulating substrate. Good agreement between the theoretical and experimental approach curves indicated that recessed nanotips are suitable for quantitative feedback mode SECM experiments.

Distinction of the Two Phases of CuTCNQ by Scanning Electrochemical Microscopy

The two known phases of CuTCNQ and TCNQ (TCNQ = 7,7',8,8'-tetracyanoquinodimethane) have been probed by scanning electrochemical microscopy (SECM) in the feedback mode. The first use of this technique for distinguishing differences in the electronic properties of semiconductor phases exploits the large differences in conductivity that exist between CuTCNQ and the parent TCNQ material and also between the CuTCNQ phases I and II. However, the packing density of the individual CuTCNQ crystals in a film structure also is shown to influence the SECM feedback response. Finally, it is shown that films of pure phase II material or mixtures of the phases can be mapped using feedback mode SECM. The SECM method provides valuable insights for elucidating properties of semiconducting solids that are mounted on insulating substrates.