Transmission Line Fault Location Research Articles

Fault location of transmission lines by wavelet packet decomposition based on SSSC and EMD

Fault location of transmission lines by wavelet packet decomposition based on SSSC and EMD

Enhancing Fault Identification, Classification and Location Accuracy in Transmission Lines

This research paper presents a proposed system for fault identification, classification and location in transmission lines using a Support Vector Machine (SVM)-based technique in conjunction with a Positive Sequence Analyzer. The objective is to develop an accurate and reliable method for identifying, classifying and locating different fault types in transmission lines. The proposed system leverages the capabilities of SVMs in handling high-dimensional feature spaces and the fault signature extraction capabilities of the Positive Sequence Analyzer. Experimental evaluations are conducted to assess the performance and effectiveness of the proposed system, comparing it with existing fault identification and classification methods. The results demonstrate the superior performance and robustness of the SVM-based technique utilizing the Positive Sequence Analyzer, providing a valuable contribution to fault management and system reliability in transmission line networks.

UHVDC transmission line diagnosis method for integrated community energy system based on wavelet analysis

With the large-scale development of renewable energy power, China has faced with the challenges of the reverse regional distribution of wind and solar resources and power load, as well as the intermittency and randomness of renewable energy power. Therefore, China is vigorously developing ultra-high voltage direct current (UHVDC) transmission technology to solve the problem of insufficient flexibility caused by the uncertainty of renewable energy and the fluctuation of multi-energy loads in integrated community energy systems. UHVDC plays an increasingly pivotal role in the west-east transmission system in China’s power system due to its high transmission capacity and long transmission distance. Once the fault occurs in the ultra-high voltage direct (UHVD) transmission line, quick and accurate fault location identification is of great significance. Hence, this paper proposes a UHVDC transmission line diagnosis method based on wavelet analysis for integrated community energy systems. Wavelet transform (WT) is used to decompose the transient signal on a multi-scale, and then power systems computer-aided design (PSCAD) software is utilized for simulation calculation to obtain the singular spectrum entropy of each layer and facilitate wavelet transformations for signal denoising with advanced tools such as MATLAB. The prediction results can distinguish outside the rectification side fault, within the rectification side fault, and outside the inverter fault with an accuracy of 100%. A large number of simulations demonstrate that combining singular spectrum entropy with support vector machines (SVM) has emerged as a robust technique for integrated community energy systems, suggesting its potential as a standard method in UHVDC transmission line diagnosis. This study is of significant reference for realizing the complementarity of multiple types of power supply and ensuring a reliable power supply.

New energy transmission line fault location method based on Pearson correlation coefficient

The access of new energy power source makes the traditional transmission line structure become complex, and due to the influence of power electronic device control strategy, the fault characteristics have been fundamentally changed, resulting in the traditional transmission line fault localization method can not be applied to the new energy sending line. To address the above problems, this paper analyzes the transient current characteristics of different power supply faults, and learns that there are obvious differences in the transient currents on both sides of the fault point inside and outside the transmission line area, and then proposes a new energy transmission line fault localization method based on the Pearson correlation coefficient, which determines the fault location by calculating the correlation coefficients of the fault waveforms of the neighboring monitoring points. Finally, comparative experiments are carried out under different fault types and fault locations to further verify the applicability of the proposed method.

Multi-Terminal Fault Locator for Homogeneous Transmission Lines Using Extended Proportions

Multi-Terminal Fault Locator for Homogeneous Transmission Lines Using Extended Proportions

VSC-HVDC transmission line fault location based on transient characteristics

VSC-HVDC transmission line fault location based on transient characteristics

Fault location of high voltage overhead transmission line based on ACO-ENN algorithm.

Fault location of high voltage overhead transmission line based on ACO-ENN algorithm.

Automated monitoring of high-voltage transmission lines based on machine vision

Abstract This paper takes the automated monitoring of high-voltage transmission lines as the entry point and constructs an automated monitoring model of high-voltage transmission lines based on machine vision. Through the transmission equipment recognition algorithm to identify the type and location of the equipment in the inspection image, using image processing methods for the collected high-voltage transmission line image color image grayscaling and grayscale image stretching, and then grayscale image smoothing and segmentation, so as to achieve the identification of the location of high-voltage transmission line fault location. Simulation test for image processing and transmission equipment identification methods, and then carry out automated monitoring experiments with high-voltage transmission line conductor stranding as an example to verify the feasibility and reliability of the model in this paper. The results show that for the automatic detection of individual conductor strand breakage, the method of this paper detects the number of strand breakage is only 1-2 less or more than the actual number of strand breakage; there is a certain difference, but basically in line with the actual situation, and the method of this paper, on average, detects the efficiency of the method is faster than the traditional method by 5.69~7.18 s/m. The research to enhance the quality of automated monitoring of high-voltage power transmission lines has a certain application value.

Retracted: Research on Transmission Line Fault Location Based on the Fusion of Machine Learning and Artificial Intelligence

Retracted: Research on Transmission Line Fault Location Based on the Fusion of Machine Learning and Artificial Intelligence

Eliminating the Dependence of GPS or Communication Latency Estimation in Traveling Wave Based Double-Terminal Fault Location

Double-terminal traveling wave-based fault location is one of the most reliable and accurate technologies for power transmission line fault location. However, existing methods require a global positioning system (GPS) or accurate communication latency estimation to synchronize data from the two terminals. In this study, we propose an innovative double-terminal traveling wave-based fault location method that is independent of either GPS or communication latency estimation. The basic principle of the proposed method is that the arrival time difference between initial surges could be roughly calculated through the angle of pre-fault phasors by artificially assigning surge arrival points as the time references. Therefore, an approximate fault distance is obtained. The error could be reduced by detecting the fault-point-reflected surge. Extensive simulation experiments were performed using PSCAD/EMTDC software to assess the performance of the proposed algorithm. The results showed that the proposed method is applicable to different fault circumstances and independent of GPS synchronization and communication latency estimation while maintaining accuracy close to those of state-of-the-art algorithms. Finally, hardware experiments were performed to assess the validity and practicability of the proposed method.

Accuracy analysis using the EMD and VMD for two-terminal transmission line fault location based on traveling wave theory

Accuracy analysis using the EMD and VMD for two-terminal transmission line fault location based on traveling wave theory

SEP Optimization of Power System Location and Timing Module Based on MLE-KNN Synthesis Algorithm

To ensure the safe operation of the power system, it is necessary to monitor and manage all kinds of power facilities. Real-time power monitoring can play a role in the early warning of geographical disasters. At the transmission end, the state detection and fault location of transmission lines are related to the normal operation of the power system. The precise time synchronization of the power system can be guaranteed through the satellite positioning time service, so that the time of various power operation actions is consistent. The accuracy can reach several microseconds, which provides a basis for the analysis of power grid operation. In this paper, by installing BeiDou functional modules in power equipment and developing the BeiDou operation platform for the distribution network, the precise management of power timing and positioning is realized by docking with the geographic information systems platform of the power grid. The three-dimensional sphere error probability (SEP) algorithm is selected to evaluate the positioning error data. Based on the three traditional SEP calculation methods, the maximum likelihood estimation algorithm is optimized and improved, which can achieve nanosecond synchronization accuracy. It can also be applied to other precision of synchronization scenarios of the power system to meet the development needs of the future clock system of the power system. Through the simulation of experimental data and comparison with other algorithms, the accuracy is verified and the reliable estimation of parameters is realized. Considering the information loss caused by dimension reduction evaluation, the simulation analysis in this paper is compared with other methods, and the accuracy is significantly improved. The power system positioning and timing module developed in this paper can not only be used in the power system but also has a certain reference and application value for other devices in the same industry that need timing and positioning services.

Fault location of untransposed double-circuit transmission lines based on an improved Karrenbauer matrix and the QPSO algorithm

Some double-circuit transmission lines are untransposed, which results in complex coupling relations between the parameters of the transmission lines. If the traditional modal transformation matrix is directly used to decouple the parameters, it can lead to large errors in the decoupled modal parameter, errors which will be amplified in the fault location equation. Consequently, it makes the fault location results of the untransposed double-circuit transmission lines less accurate. Therefore, a new modal transformation method is needed to decouple the parameter matrix of untransposed double-circuit transmission lines and realize the fault location according to the decoupled modal parameter. By improving the basis of the Karrenbauer matrix, a modal transformation matrix suitable for decoupling parameters of untransposed double-circuit transmission lines is obtained. To address the difficulties in solving the fault location equation of untransposed double-circuit transmission lines, a new fault location method based on an improved Karrenbauer matrix and the quantum-behaved particle swarm optimization (QPSO) algorithm is proposed. Firstly, the line parameter matrix is decomposed into identical and inverse sequence components using the identical-inverse sequence component transformation. The Karrenbauer matrix is then transformed to obtain the improved Karrenbauer matrix for untransposed double-circuit transmission lines and applied to identical and inverse sequence components to solve the decoupled modal parameter. Secondly, based on the principle that voltage magnitudes at both ends are equal, the fault location equation is expressed using sequence components at each end, and the QPSO algorithm is introduced to solve the equation. Finally, the feasibility and accuracy of the proposed method are verified by PSCAD simulation. The simulation results fully demonstrate that the innovative improvement on the basis of the traditional modal transformation matrix in this paper can realize the modal transformation of the complex coupling parameters of the untransposed double-circuit transmission lines. It causes almost no errors in the decoupling process. The QPSO algorithm can also solve the fault location equation more accurately. The new fault location method can realize the accurate fault location of untransposed double-circuit transmission lines.

Fault location in hybrid transmission lines on the basis of VMD energy entropy and SVM

Finding the head of a traveling wave is challenging because an overhead line-cable hybrid transmission line’s wave impedance is not constant. Because of this, it is difficult to measure the hybrid transmission line precisely. This leads to the proposal of a hybrid transmission line fault location algorithm, which combines VMD energy entropy for training support vector machines and traveling wave law graphs. The VMD energy entropy is first used to train SVM to identify the faulty section. The method of traveling waves with a single end is utilized to precisely fix the fault distance within the faulty segment when the type of traveling wave has been identified. The simulation results demonstrate that the method provides precise measurements and is effective for hybrid transmission lines with a range of fault distances and grounding resistances.

Fault Location Study of Overhead Line–Cable Lines with Branches

A new fault location method based on the three-terminal travelling wave method is proposed for the fault location problem of multi-branch overhead line–cable transmission lines. Firstly, the process of fault travelling wave propagation in overhead transmission lines and the phenomenon of refraction are analysed, and an improved phase-mode transformation is introduced to decouple the electromagnetic coupling and perform fault phase selection. Secondly, the Pearson correlation coefficient is introduced to compare the similarity of the current travelling waveforms at different measurement points in order to implement fault segmentation. To solve the problems of the complexity of the fault travelling wave propagation process and the difficulty of identifying the travelling wavehead, the Hilbert–Huang transform is used to extract the fault signal characteristics, and the travelling wave arrival moment is accurately calculated by the sampling error correction method to determine the fault location. Finally, the accuracy and stability of the method are verified via a simulation test on the MATLAB/Simulink platform. The results show that the proposed positioning method combining the three-terminal travelling wave method with HHT and sampling error correction can locate the fault location more accurately, and it has good potential for application in the engineering field. It provides a new technical means for fault location in overhead transmission lines, which is expected to become one of the most important technologies in the future power system.

Adaptive Fault Locator for High-Voltage Transmission Lines Based on the Estimation of Power System Model Parameters

Abstract This paper presents an adaptive transmission line fault location method, which incorporates fault location devices at both line ends and utilises data import from a supervisory control and data acquisition system without strictly requiring data synchronisation. The developed method aims at achieving a higher degree of robustness, adaptiveness and accuracy. The adaptiveness is achieved by dynamic updating of mathematical models used on the basis of network-wide information, such as data on the state of circuit-breakers and apparent power at load and generation nodes. The robustness and accuracy are enhanced by incorporating two stages of identification of model parameters with the goal of reducing the decision variable space for the stage identifying fault parameters. Furthermore, in addition to utilisation of all measurements available at a particular substation, the developed method partially employs the measurements from the other end of the line by means of result cross-checks, but does not require a full data set, unlike deterministic-model-based methods. An optimisation-based approach, redundancy on the basis of extended measurement set, and cross-checks reduce the risk of fault location errors due to measurement errors or “voids” in the data available. Testing of the developed method demonstrates its accuracy and robustness in a wide range of pre-fault and fault regime scenarios, even when considering various pre-fault contingencies.

Neural Network based Transmission Line Fault Classifier and Locator using Sequence Values

Faults can easily occur at transmission line because the line is exposed to the environment. The fast fault location after a fault occurrence will minimize the time to repair the faulty part thus reduce the stress of power system due to long outage time. This paper demonstrates the development of fault classifier and fault locator using neural network. The positive, negative and zero sequence values of three-phase voltage and current during fault time were used as the inputs to train the neural networks. Various fault conditions which have different fault types, fault resistance values and fault locations have been simulated to generate the training data for both neural network based fault classifier and fault locator. From the results, the fault classifier and locator successfully classified and located all the simulated fault conditions. One of the advantages of using sequence values as the inputs for the neural networks is only one fault type need to be simulated and used as the training data for single line-to-ground fault (RG, YG and BG), line-to-line fault (RY, YB, BR) and double line-to-ground fault (RYG, YBG, BRG).

Improving Traveling Wave-Based Transmission Line Fault Location by Leveraging Classical Functions Available in Off-the-Shelf Devices

This letter presents a practical methodology to improve traveling wave (TW)-based fault location (TWFL) on transmission lines by leveraging classical single- and double-ended TWFL functions available in off-the-shelf relays and digital fault recorders. It eliminates negative effects of uncertainties in line propagation velocity and travel time, being free of time-consuming or complicated procedures. Real TW records are studied to demonstrate that the proposed solution can improve the accuracy and reliability of TWFL estimations when uncertainties about line propagation velocity or travel time exist.

Robust Fault Location Method for Transmission Lines Using PMUs

The random noise and abnormally greater numbers may affect the accuracy of traditional transmission line fault location. A robust fault location method for transmission lines based on PMUs (Phasor Measurement Unit) is proposed in this paper. The node voltage equations based on voltage fault components are adopted to establish the quadratic nonlinear overdetermined equations of fault location, only using limited PMUs adjacent to the faulted line. In order to quantify the impact of measurement errors, the residual errors are introduced into the fault location equations. Levenberg-Marquardt (L-M) algorithm has been used to solve the equations. Then the original fault location data at each time after the occurrence of one cycle is obtained. A filtering method is proposed to filter the possible interference such as noise and abnormally greater numbers in fault location sequence. The abnormal data that deviating from the mean can be detected by the probability distribution and replaced by smooth filtering data. The simulation results on IEEE 39-bus systems show that proposed algorithm can effectively improve the location accuracy, is not affected by the fault location, transition resistance, fault type, and has strong anti-interference ability and good robustness.

DEVELOPMENT OF A COMPREHENSIVE APPROACH TO DIAGNOSING THE OVERHEAD LINE FAULTS LOCATION IN SINGLE-PHASE GROUND FAULTS BASED ON A DIGITAL SUBSTATION DATA PROCESSING ALGORITHM

Link for citation: Sushkov V.V., Sukhachev I.S., Sidorov S.V. Development of a comprehensive approach to diagnosing the overhead line faults location in single-phase ground faults based on a digital substation data processing algorithm. Bulletin of the Tomsk Polytechnic University. Geo Аssets Engineering, 2023, vol. 334, no. 7, рр. 66-77. In Rus. Relevance. Emergency of electric complex of outgoing transmission lines is associated with the occurrence of damage to the line isolation and the resulting transients, marked by the presence of higher harmonic components of currents and voltage, which reduce the reliability and energy efficiency of electrical equipment of oil and gas companies: degrade the mechanical characteristics and efficiency of electric motors, accelerate aging of their isolation, disrupt the operation of control systems and emergency automatics, fault diagnostics systems. One of the reasons of high-level emergency situations, outages and emergency repairs in electric complexes of outgoing transmission lines of oil and gas companies is appearance of phase-to-ground faults. A large number of changing factors are known to influence the reliability of phase-to-ground fault location methods: parameters of transmission line operating mode, its structural and electrical parameters, fault type, transient resistance value, ground resistance and others. Inclusion in the transmission line fault location algorithms of averaged values of a number of the factors listed above independent of changes of humidity of soil and air, its temperature and other factors causes an error of methods of fault location up to 30 %. Accordingly, the research to develop a fault location method for overhead transmission lines with isolated neutral points during phase-to-ground faults based on a digital substation data processing algorithm, accounting for tower parameters and natural-climatic factors, is relevant. Objective: improving the reliability of power grids and providing consumers with power of the required standard by applying a digital fault location system to the outgoing transmission lines electrical complex. Methods: mathematical analysis of a power transmission line, taking into account its design features and natural-climatic factors on the basis of the method of mirror images; mathematical analysis of steady-state and transient modes of transmission line operation considering self and mutual parameters terms of wires; transmission line currents and voltages Fourier analysis; validation of developed method of phase-to-ground fault location in power grid of Tyumen region energy company. Results. The authors have developed the phase-to-ground faults location method for transmission lines in power grids with isolated neutral points, which differs in the following – first the faulty overhead line feeder branch is identified by correspondences between the negative sequence voltage values of the phase voltages at the transformer substation inputs, and then the distance to the location of the single-phase ground fault is determined along the branch line based on the resonant frequencies of the line taking into account its design features and natural and climatic factors.