Fabrication Of Fiber Bragg Gratings Research Articles

Non-invasive FBG-based contact lens for continuous intraocular pressure monitoring

The intraocular pressure (IOP), or pressure inside the eye, is one of the key indicator for glaucoma diagnosis and treatment. The present work shows the design and fabrication of a non-invasive Fiber Bragg Grating (FBG) based contact lens for continuous IOP monitoring. By employing wet etching to reduce the FBG diameter, FBG based contact lens sensitivity and mechanical flexibility are enhanced. The contact lens is made of an optical fiber with a small core diameter that has an inscribed FBG of length 3 mm and is etched for a length of 40 mm to facilitate coiling the eFBG during fabrication. The soft contact lens was fabricated using flexible thin film technology with a transparent and flexible etched Fiber Bragg Grating (eFBG) integrated within flexible polydimethylsiloxane (PDMS) for sensing corneal deformations brought about by IOP variations. Experimental studies on the bionic eyeball model show that the Bragg wavelength shift is highly linear (r2 = 0.9694), with a very good sensitivity of 49.243 pm/mmHg in the IOP pressure range of 0 to 50 mmHg. Due to its ease of fabricating, simplicity of design, and ability to continuously measure pressure with good repeatability and stability, the proposed sensor thus offers a potential solution for IOP monitoring.

Linewidth compression of a single longitudinal mode ytterbium-doped fiber laser based on femtosecond laser fabricated fiber Bragg gratings.

We demonstrate a single longitudinal mode distributed Bragg reflection (DBR) fiber laser by directly fabricating fiber Bragg gratings (FBGs) on an ytterbium-doped fiber (YDF) using a femtosecond laser. A simple optical self-injection feedback method was used to effectively compress the linewidth and reduce relative intensity noise (RIN) of a single longitudinal mode DBR fiber laser. Further, we investigated the effect of self-injection feedback cavity length and reflectivity on linewidth compression and determined that the linewidth tends to decrease with the increase of the external cavity photon lifetime. By a self-injection feedback, the laser linewidth was compressed from 31.8kHz to 1.4kHz. Meanwhile, the relaxation oscillation peak from -103.2d B/H z at 1.51MHz was suppressed to -122.3d B/H z at 0.16MHz. This low-noise narrow linewidth single longitudinal mode fiber laser is expected to be a promising candidate for applications such as active detection of neutral atmosphere and distributed fiber sensing.

Fabrication of Low-Loss Femtosecond Fiber Bragg Gratings Based on Beam Shaping by Small Aperture

Fabrication of Low-Loss Femtosecond Fiber Bragg Gratings Based on Beam Shaping by Small Aperture

Design and Fabrication of a Fiber Bragg Grating Shape Sensor for Shape Reconstruction of a Continuum Manipulator.

Continuum dexterous manipulators (CDMs) are suitable for performing tasks in a constrained environment due to their high dexterity and maneuverability. Despite the inherent advantages of CDMs in minimally invasive surgery, real-time control of CDMs' shape during nonconstant curvature bending is still challenging. This study presents a novel approach for the design and fabrication of a large deflection fiber Bragg grating (FBG) shape sensor embedded within the lumens inside the walls of a CDM with a large instrument channel. The shape sensor consisted of two fibers, each with three FBG nodes. A shape-sensing model was introduced to reconstruct the centerline of the CDM based on FBG wavelengths. Different experiments, including shape sensor tests and CDM shape reconstruction tests, were conducted to assess the overall accuracy of the shape-sensing. The FBG sensor evaluation results revealed the linear curvature-wavelength relationship with the large curvature detection of 0.045 mm and a high wavelength shift of up to 5.50 nm at a 90° bending angle in both the bending directions. The CDM's shape reconstruction experiments in a free environment demonstrated the shape-tracking accuracy of 0.216 ± 0.126 mm for positive/negative deflections. Also, the CDM shape reconstruction error for three cases of bending with obstacles was observed to be 0.436 ± 0.370 mm for the proximal case, 0.485 ± 0.418 mm for the middle case, and 0.312 ± 0.261 mm for the distal case. This study indicates the adequate performance of the FBG sensor and the effectiveness of the model for tracking the shape of the large-deflection CDM with nonconstant-curvature bending for minimally invasive orthopedic applications.

High temperature and strain dual-parameters fiber sensing based on intermodal interference and femtosecond laser fabricated fiber Bragg grating

In this paper, the sensor was proposed by combination of grapefruit photonic crystal fiber (GPCF) and femtosecond laser fabricated fiber Bragg grating (FBG) based on Sagnac interferometer. The GPCF was sandwiched between two single-mode fibers (SMFS) to form a SMF-GPCF-SMF structure, which was based on intermodal interference. The FBG with a central wavelength of 1535.32 nm was inscribed through polyimide coating and cladding by the femtosecond laser point-by-point inscribing method. The spectrum drift data of sensing structure were collected and the dual-parameters matrix of temperature-strain was constructed to realize the simultaneous measurement of temperature and strain. The experimental results showed that the linear range of the strain measurement was from 0 με to 2,000 με at different temperature, the wavelength of FBG and GPCF was red drift and blue drift, respectively, the average strain sensitivity at different temperature was 1.25 pm/με and −2.05 pm/με, all the linearity R2 are higher than 0.999, and has the high repeatability. The linear range of temperature measurement was from 20 °C to 450 °C, the wavelength of FBG and GPCF was red drift and blue drift, respectively, the temperature sensitivity of FBG and GPCF was 15.17 pm °C−1 and −8.87 pm °C−1, the linearity was 0.99983 and 0.99989, respectively.

Femtosecond laser fabrication of large-core fiber Bragg gratings for high-power fiber oscillators

In this paper, a fs-laser phase mask inscription system based on a galvanometer scanning strategy is designed and set up for the fabrication of large-core fiber Bragg gratings (FBGs). Based on this setup, a homogeneous cross-sectional refractive index modulation can be achieved in the core of a large-mode-area fiber, and a pair of FBGs are fabricated in fibers with a core diameter of 30 µm. To investigate the performance of the fabricated FBGs, a high power all-fiber oscillator is built using a pure backward pumping structure. The FBGs work well, and the maximum output power of 7920 W is achieved with an optical–optical conversion efficiency of 77.3%. To the best of our knowledge, this is the highest power of all-fiber oscillators based on fs-written FBGs. This work provides a flexible, stable, and economic scanning strategy for large-core FBG inscription and exhibits excellent performance for high power fiber lasers.

Serially Connected Cantilever Beam-Based FBG Accelerometers: Design, Optimization and Testing.

We focus on the design, optimization, fabrication, and testing of fiber Bragg grating (FBG) cantilever beam-based accelerometers to measure vibrations from active seismic sources in the external environment. These FBG accelerometers possess several advantages, such as multiplexing, immunity to electromagnetic interference, and high sensitivity. Finite Element Method (FEM) simulations, calibration, fabrication, and packaging of the simple cantilever beam-based accelerometer based on polylactic acid (PLA) are presented. The influence of the cantilever beam parameters on the natural frequency and sensitivity are discussed through FEM simulation and laboratory calibration with vibration exciter. The test results show that the optimized system has a resonance frequency of 75 Hz within a measuring range of 5-55 Hz and high sensitivity of ±433.7 pm/g. Finally, a preliminary field test is conducted to compare the packaged FBG accelerometer and standard electro-mechanical 4.5-Hz vertical geophones. Active-source (seismic sledgehammer) shots are acquired along the tested line, and both systems' experimental results are analyzed and compared. The designed FBG accelerometers demonstrate suitability to record the seismic traces and to pick up the first arrival times. The system optimization and further implementation offer promising potential for seismic acquisitions.

High-quality fiber Bragg grating inscribed in ZBLAN fiber using femtosecond laser point-by-point technology.

We demonstrate for the first time, to the best of our knowledge, the fabrication of a high-quality fiber Bragg grating (FBG) in ZBLAN fiber by using an efficient femtosecond laser point-by-point technology. Two types of FBG, e.g., high coupling coefficient and narrow bandwidth grating, are successfully obtained. The coupling coefficient is strongly dependent on the grating order and pulse energy. A second-order FBG with an ultrahigh coupling coefficient of 325 m-1 and reflectivity of 97.8% is inscribed in the ZBLAN fiber. A pair of FBGs with a narrow FWHM of 0.30 and 0.09 nm are also demonstrated.

Bragg grating in a flexible and stretchable coreless polymer optical fiber.

In this Letter, we propose and experimentally demonstrate fiber Bragg grating (FBG) fabrication in a flexible and stretchable coreless polymer optical fiber. The flexible polymer optical fiber is prepared with polydimethylsiloxane (PDMS). Femtosecond laser direct writing and slit beam shaping are used to form periodic grating structures in the fiber. The fabricated FBG exhibits a large strain measurement range and a blueshift response to temperature. Moreover, it offers low humidity sensitivity due to its low permeability toward water vapor. Taking advantage of the unique sensing performances of the PDMS fiber, the proposed FBG has considerable advantages over the traditional silica FBG devices for strain and temperature sensing.

Direct Femtosecond Laser Inscription of High-Order Bragg Gratings in Fluoroaluminate Glass Fiber

This letter reports the fabrication of fiber Bragg gratings (FBGs) within in-house fabricated fluoroaluminate (AlF₃) glass fibers using femtosecond (fs) laser inscription at 800 nm. The grating strength of the FBGs was investigated for different pulse energies and different orders, and a 3rd-order FBG with Bragg wavelength at 1557 nm was found to have the highest reflectivity of 99.5%. In addition, the reflectivity of the mid-IR grating peaks for different orders was also studied, and a 2nd-order FBG with a reflectivity of 98.8% was obtained at 2864 nm. Finally, the temperature characteristics of a mid-IR FBG were studied between 30 °C and 150 °C, showing a linear wavelength dependence and an excellent stability for the refractive index modulation. Such highly reflectivity FBGs in AlF₃ fiber have significant potential for applications in the development of compact all-fiber mid-IR fiber lasers.

Femtosecond laser point-by-point inscription of helical-sampled fiber Bragg gratings

In this Letter, a helical-sampled fiber Bragg gratings (HSFBGs) fabrication using a femtosecond laser point-by-point (PBP) technique is proposed. The unique helical structure generates sampled gratings owing to its periodicity. A simple, single-step method for inscription of the sampled gratings is described. The effects of geometrical parameters, including length of grating, helical diameter, helical pitch, and off-axis distance on the resonances are studied, and a series of comb-like spectra are obtained.

Fabrication of Fiber Bragg Gratings by Visible Femtosecond Laser for Multi-kW Fiber Oscillator

In this paper, we fabricate a pair of fiber Bragg gratings (FBGs) in large mode area double cladding fiber (LMA-DCF, core/inner cladding diameter: 20/400 μm) by visible (515 nm) femtosecond laser and phase mask for the first time to the best of our knowledge. Then this pair of FBGs are utilized to construct a high power fiber oscillator operated near 1080 nm. The maximum output laser power is more than 3.2 kW with a slope efficiency of ∼77.9%, and the beam quality factor M <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> is about 1.28. The FBGs are simply fixed on water-cooling plate without any special package, and the temperature of the FBGs is about 40 °C at the maximum output power. Our research work confirms the reliability of visible femtosecond laser in fabrication of FBGs intended to be applied in high power fiber oscillators.

Direct femtosecond laser inscription of Bragg gratings in Ho3+/Pr3+ co-doped AlF3-based glass fibers for a 2.86 µm laser.

In this Letter, we report the fabrication of fiber Bragg gratings (FBGs) in home-made Ho3+/Pr3+ co-doped single-cladding fluoroaluminate (AlF3) glass fibers and its application in watt-level lasing at the mid-infrared (MIR) wavelength of 2.86 µm. The FBGs were inscribed using an 800 nm femtosecond (fs) laser direct-writing technique. The FBG properties were investigated for different pulse energies, inscription speeds, grating orders, and transversal lengths. A second-order FBG with a high reflectivity of 99% was obtained at one end of a 16.5-cm-long gain fiber. Under 1150 nm laser pumping, this fiber yielded a power exceeding 1 W at 2863.9 nm with an overall laser efficiency of 17.7%. The fiber laser showed a FWHM bandwidth of 0.46 nm and long-term spectral stability.

Femtosecond-Laser-Assisted Fabrication of Radiation-Resistant Fiber Bragg Grating Sensors

This paper demonstrates the fabrication of radiation-resistant fiber Bragg grating (FBG) sensors using infrared femtosecond laser irradiation. FBG sensors were written inside acrylate-coated fluorine-doped single-mode specialty optical fibers. We detected the Bragg resonance at 1542 nm. By controlling the irradiation conditions, we improved the signal strength coming out from the FBG sensors. A significant reduction in the Bragg wavelength shift was detected in the fabricated FBG sensors for a radiation dose up to 105 gray, indicating excellent radiation resistance capabilities. We also characterized the temperature sensitivity of the radiation-resistant FBG sensors and detected outstanding performance.

Fabrication and Refractive Index Sensing Characteristics of Exposed-Core Side-Hole Fiber Bragg Grating

Fabrication and Refractive Index Sensing Characteristics of Exposed-Core Side-Hole Fiber Bragg Grating

Line Position-Dependent Effect in Line-by-Line Inscribed Fiber Bragg Gratings.

Line-by-line direct writing by femtosecond laser has been proved to be a simple and effective method for the fabrication of low-loss fiber Bragg gratings (FBGs), and is more flexible compared with the traditional ultraviolet exposure method. In this paper, the line-position-dependent characteristics of cladding modes coupling in line-by-line FBGs have been studied, to the best of our knowledge, for the first time. Both theoretical and experimental results show that off-center inscribing could compress the bandwidth of the Bragg resonance and excite more abundant cladding mode coupling, in which the core-guided fundamental mode would couple to the cladding-guided LP0n and LP1n simultaneously. By aligning the line positions across the core region, the first apodized line-by-line FBG was achieved. This work enriches the theories of line-by-line FBGs and provides an inscription guidance to meet different application requirements.

Direct femtosecond laser inscription of an IR fluorotellurite fiber Bragg grating.

This study proposes a novel, to the best of our knowledge, development of fluorotellurite glass fiber Bragg gratings (FBGs). Shell-like morphology was achieved using a single femtosecond laser pulse illuminated through the fiber's polymer coating. Different FBG fabrication methods and parameters were systematically studied to optimize performance. The fluorotellurite FBG exhibited a high sensitivity to writing laser power and reflectivity saturation effect in repetitive writing. A low-insertion-loss fluorotellurite FBG with a reflectivity of over 99% and bandwidth of less than 1 nm was successfully inscribed. The flexible inscription methods can write an FBG at any wavelength in the fluorotellurite glass transparent window, and are applicable to infrared fiber lasers or sensors.

Single nanosecond-pulse production of polymeric fiber Bragg gratings for biomedical applications.

In this study, we present first-time fabrication of FBGs in all ZEONEX-based SMPOFs with a single 25 ns pulse of 248 nm UV irradiation over a 12-month period, which opens up new frontiers in optics and photonics for the effective fabrication of polymer optical fiber Bragg gratings (POFBGs), permitting mass producibility of them. POFBGs were characterized by subjecting them to various physical parameters including temperature and tensile strain. Strain responses of FBGs with similar grating strengths fabricated with 248 nm and 325 nm He-Cd laser irradiations were explored over a year to demonstrate their long-term stability and applicability. Owing to the unique features of the proposed sensing device fabricated by embedding POFBGs in silicone rubber, a good performance in the detection of human heart rate with an amplitude of 4 pm, which is 4 times higher compared to that of silica single mode fiber (SMF) was demonstrated. The response of the sensing device during a human respiration process was also explored where exhalation and inhalation were monitored and distinguished while the breath was held. These revelations signify the importance of ZEONEX-based POFBGs, which allow consistent and effective grating fabrication and are highly promising in the foreseeable future for biomedical applications.

High-precision fiber Bragg gratings inscription by infrared femtosecond laser direct-writing method assisted with image recognition.

For achieving high efficiency fiber Bragg gratings (FBGs) utilizing infrared femtosecond laser point-by-point inscription method, it is crucial to make the inscribed periodic structure perfectly in phase. It requires a perfect alignment between the micrometer-sized laser spot with the fiber along the length. Here we report the highly precise fabrication of FBGs by infrared femtosecond laser point-by-point direct-writing method. Image recognition technique is applied to for automatically aligning the trace of the laser spot with the referenced central axis of the fiber along the whole FBG length. FBGs inscription with high spatial precision is confirmed by multiple approaches, including microscopic photographing and FBG spectroscopic measurement. 50 mm-long uniform FBGs with high reflectivity have been successfully demonstrated in a small-core single-mode silica fiber using auto-aligning technique.

Bragg gratings and Fabry-Perot interferometers on an Er-MgO-doped optical fiber

In this paper, the fabrication of fiber Bragg gratings (FBGs) and intrinsic Fabry-Pérot interferometers (IFPIs) on an Er-MgO-doped silica optical fiber is reported. The inscription of both sensing devices was performed by means of a femtosecond laser, using the phase mask method to inscribe the FBG and a micromachining platform for the IFPI. Thermal and strain characterizations were performed for both devices, achieving the maximum sensitivities of 12.57 pm/°C and 0.85 pm/µε for the FBG case, and 10.2 pm/°C and 0.91 pm/µε for the IFPI. A high temperature experiment was conducted to assess the thermal behavior of the inscribed FBG, revealing sensing capabilities for temperatures up to 700 °C. The results confirm that this new type of fiber will have an important role on the development of new optoelectronic devices, such as fiber lasers, optical amplifiers and sensors.