Experimental System Research Articles

Optimization of the on/off status configuration of control units in an active vibration isolation system—experiment

Active vibration isolation (AVI) is an important measure to attenuate vibration transmission in underwater vehicles and multiple active control units are usually used to attenuate low frequency vibrations induced by power equipment. Under certain operation conditions, however, the pre-installed control units in an AVI system may be redundant. Hence, it is necessary to optimize the on/off status configuration of all the control units. An optimization approach is proposed for configuration optimization of control units and validated by experiments. The criterion of the proposed approach is derived from the vibration responses of the monitoring points. The involved optimization, formulated as a constrained 0–1 nonlinear programming problem, utilizes the on/off status of control units as the input variable and the number of active units as the constraint. Optimized configurations were obtained by solving the nonlinear programming problem and deployed to the experimental system. The test results have demonstrated that vibration of the monitoring points can be effectively suppressed by activating only a portion of control units, and the configurations corresponding to maximum vibration reduction vary with different excitations.

Experimental Study on Evaporation and Micro-Explosion Characteristics of Ethanol and Diesel Blended Droplets

In this study, the constant temperature control system of a heating plate was established, ethanol–diesel fuel with different proportions was prepared, and a series of experiments were carried out. The experimental system was used to observe, summarize, and analyze four evaporation and crushing modes of mixed droplets, which were explosion, liquid filament stretching, exocytosis, and ejection mode. The evaporation process of four kinds of mixed droplets in their life cycle was analyzed by normalizing the diameter square. It was proposed that the evaporation process of droplets could be divided into the following three stages: a heating stage, a fluctuating evaporation stage, and an equilibrium evaporation stage. It was also pointed out that the expansion, ejection, and micro-explosion of droplets were the causes of fluctuating evaporation. The concept of expansion and crushing intensity was put forward and the expansion and crushing intensity of ethanol/diesel mixed droplets with different proportions were calculated. The reasons why expansion and crushing intensity first increased and decreased with the increase in ethanol blending ratio were analyzed. Finally, the time proportion of ethanol–diesel mixed droplets in each evaporation stage was calculated, which explained that the time proportion of the instantaneous heating stage showed a parabolic law with the increase in ethanol content.

Theoretical and Experimental Research on Thermal Dynamic Characteristics of Single-Screw Compressor with a New Composite SLIDE valve

Based on the single-screw compressor (SSC) structure, a new type of composite slide valve (CSV) has been proposed and designed, featuring internal volume ratios of 2.8, 3.9, and 5.6 and operating under a partial load of 35%. The theoretical model describing the dynamic features and thermodynamic performance of the SSC with CSV has also been built. The pressure ratio of the experimental system can be adjusted from 3.3 to 7.8, and the experimental results demonstrate the CSV’s effective performance. The deviations between the calculated and measured results for volume ratio and input power are 3.33–9.08% and 0.32–8.03%, and the deviations for heating capacity and adiabatic efficiency range from 0.92–8.73% to 2.09–9.67%, respectively. The introduction of the CSV offers a novel approach to enhancing SSC efficiency. Both the theoretical and experimental findings lay a foundation for future optimization and design improvements in variable load and internal volumetric ratio single-screw compressors.

Hybrid diffractive-refractive lens for chromatic confocal measurement system

A novel chromatic confocal measurement (CCM) method using a hybrid diffractive- refractive lens is presented. This hybrid diffractive- refractive lens is designed to optimize the linearity of chromatic dispersion and minimize the size of the optical system. The hybrid diffractive- refractive lens is fabricated by etching a diffractive surface onto a quartz aspheric lens through lithography, which combines the high numerical aperture (NA) of a refractive lens with the unique dispersion properties of the diffractive optical elements (DOE). The lens is incorporated as a dispersive objective lens in a CCM experimental system. The system has a measurement range of 514.8 µm, calibrated using a laser displacement interferometer. The experimental results show that the wavelength-to-axial position coding of the CCM system achieves high linearity (R2= 0.9999) in the working wavelength range (500-700 nm). The system has an axial resolution of 0.08 µm and a displacement measurement nonlinear error of less than 2.05 µm.

Carbon foam to enhance the performance of a slurry flow energy system used for hydrogen storage and transportation: An experimental investigation

A novel idea of using carbon foam (CF) is introduced to enhance the electrochemical performance of a slurry electrode system in a proton flow reactor system. Steam-activated and acid-washed Norit from peat is used as active charge carrier particles to prepare 15 wt% carbon slurry to be used in this study. The slurry flow rates in the experimental electrochemical system can be varied from 0 to 200 ml min−1, while using two channel widths of 1.6 cm and 2 cm to facilitate the slurry flow. Two sets of CFs with 10 pores per inch (PPI) and 5 PPI are used to understand the effect of introducing CFs with different pore sizes on the performance of slurry electrode. Slurry is charged slurry up to 100 C under constant application of 10 mA and 30 mA. After adding CF, the results show a significant drop in charging potential to generate both levels of current of 25% after using 5 PPI and 41% with 10 PPI. Furthermore, using the narrow channel flow of 1.6 cm and increasing the slurry flow rate from 100 ml min−1 to 150 ml min−1 lower the charging potential considerably by 19% and 21% (compared to base slurry) for 5 PPI and 10 PPI CF, respectively. Application of CF further enables the system to attain higher discharging time during the discharge cycle, and a maximum of 336% and 115% discharging capacity improvement is observed with 10 PPI and 5 PPI CF, respectively.

Experimental and Numerical Study of Superheated Steam Drying for Sliced Avocado

AbstractSuperheated steam drying (SSD) of sliced avocado is studied by both experiment and theory. An experimental system is built to evaluate the effects of drying temperature and gas velocity on the evaporation rate and color change of the product. Experiments are conducted for ripened Booth avocado from Daklak province of Vietnam. Experimental results show that evaporation is faster at higher temperatures and velocities, but the effect of temperature decreases at higher velocities. At temperatures below 130 °C, the product is not brown, but at a temperature in the range of 130–150 °C, the dried sample is burned. The experimental model is fitted with high accuracy to predict the moisture rate as a function of time. The evaporation processes of SSD are also compared with hot air drying at the same drying conditions. To extend the application ability of the result, the theoretical model is developed on the basis of Fick's law in which the spatial distributions of temperature and moisture are taken into account. The effective diffusivity is determined by an optimization tool with good agreement. This parameter is constant for all drying conditions, so the model can be applied to a huge range of drying conditions. The numerical results show that the temperature is almost uniform in the sample because of high thermal conductivity, but the moisture gradient is significant.

ANALYSIS OF THE OUTCOMES OF IMPLEMENTING THE EXPERIMENTAL SYSTEM FOR FUTURE TRANSLATORS’ PROFESSIONAL TRAINING BASED ON LOCALIZATION

The ongoing evolution of the higher linguistic education system is primarily focused on addressing the demands of society and the government for competent translators. This necessitates corresponding modifications in the professional training, development, and personal growth of future translation personnel, with the ultimate goal of fostering their preparedness for localization. The paper aims to provide a comprehensive overview of the outcomes obtained from implementing an experimental system for teaching prospective translators in localization, as well as their subsequent analysis. Clear algorithmization is necessary for any experimental activity, including the professional training of prospective translators for localization. A linear pedagogical experiment was conducted to implement and experimentally verify the author’s pedagogical system. The experiment was designed in a series of consecutive steps. To test the hypothesis proposed in the study, it was deemed necessary to approve the structural and functional model of the experimental system. This approval was intended to establish a program of experimental work that aims to create the required pedagogical conditions in both academic and extracurricular classes. The ultimate goal is to enable students to develop themselves as individuals, both personally and professionally. The effectiveness of the presented results was demonstrated through the use of theoretical analysis of scientific literature on the research problem. This analysis facilitated the selection and comprehension of didactic material. Additionally, a critical and analytical examination of concepts, theories, and methods was conducted to identify potential solutions for the problem under investigation. Furthermore, mathematical statistics methods were employed to quantitatively calculate the obtained data. The author’s methodology of incorporating various experimental new designs into the professional training of future translators for localization is deemed effective, as evidenced by the generalized results of the preparedness of future translators for localization.

Protocol Standardization of Homeopathic Medicines' Preparation and Dosing for Experimental Model Systems In Vitro.

Protocol Standardization of Homeopathic Medicines' Preparation and Dosing for Experimental Model Systems In Vitro.

Nucleotide sequence as key determinant driving insertions at influenza A virus hemagglutinin cleavage sites

Highly pathogenic avian influenza viruses (HPAIVs) emerge from H5 and H7 low pathogenic avian influenza viruses (LPAIVs), most frequently upon insertions of nucleotides coding for basic amino acids at the cleavage site (CS) of the hemagglutinin (HA). The exact molecular mechanism(s) underlying this genetic change and reasons underlying the restriction to H5 and H7 viruses remain unknown. Here, we developed a novel experimental system based on frame repair through insertions or deletions (indels) of HAs with single nucleotide deletions. Indels were readily detected in a consensus H5 LPAIV CS at low frequency, which was increased upon the introduction of only one substitution leading to a longer stretch of adenines at the CS. In contrast, we only detected indels in H6 when multiple nucleotide substitutions were introduced. These data show that nucleotide sequence is a key determinant of insertions in the HA CS, and reveal novel insights about the subtype-specificity of HPAIV emergence.

Laser-Based Mobile Visible Light Communication System

Mobile visible light communication (VLC) is key for integrating lighting and communication applications in the 6G era, yet there exists a notable gap in experimental research on mobile VLC. In this study, we introduce a mobile VLC system and investigate the impact of mobility speed on communication performance. Leveraging a laser-based light transmitter with a wide coverage, we enable a light fidelity (LiFi) system with a mobile receiving end. The system is capable of supporting distances from 1 m to 4 m without a lens and could maintain a transmission rate of 500 Mbps. The transmission is stable at distances of 1 m and 2 m, but an increase in distance and speed introduces interference to the system, leading to a rise in the Bit Error Rate (BER). The mobile VLC experimental system provides a viable solution to the issue of mobile access in the integration of lighting and communication applications, establishing a solid practical foundation for future research.

Study of Self-Excited Thermomechanical Oscillator with Shape Memory Alloys

In this paper, a new type of self-excited thermomechanical oscillator containing an oscillating shape memory alloy (SMA) filament with two symmetrically arranged spheres is investigated. The self-excitation of the oscillations is due to a heater of constant temperature, which causes periodic contractions of the filament when it approaches it. The contracted filament moves away from the heater a distance sufficient to cool it. Under the action of the weight of the spheres, the cooled filament re-approaches the heater, causing the above processes to repeat periodically. On the basis of experimental studies, approximating functions of the heater’s heat field distribution are derived. A dynamic model of the oscillator has been created, in which the minor and major hysteresis in the SMA alloy and the distribution of the heat field around the heater have been taken into account. Through numerical solutions of the differential equations, the laws of motion of the spheres are obtained. The displacements of the spheres in two perpendicular directions were measured using an experimental system. The obtained experimental results validate the proposed dynamic model and its assumptions with a high degree of confidence. Conclusions are drawn about the stochastic nature of the oscillations due to the hysteresis properties of the SMA and the temperature variation of the natural frequency of the oscillating system.

Self-Calibration Method for Circular Encoders Based on Inertia and a Single Read-Head

This article proposes a new self-calibration method for circular encoders based on inertia and a single read-head. The velocity curves of the circular encoder are fitted with polynomials and, based on the principle of circle closure and the periodicity of the distribution for angle intervals, the proportionality between the theoretical value and the actual value of each angle interval is obtained. In the experimental system constructed, the feasibility of the proposed method was verified through self-calibration experiments, repeatability experiments, and comparative experiments with the time-measurement dynamic reversal (TDR) method. In addition, this article also proposes an iterative method to improve the self-calibration accuracy. Experimental verification was carried out, and the results show that the new method can effectively compensate for the error of angle measurement in the circular encoder. The peak-to-peak value of the error of angle measurement was reduced from 239.343” to 11.867”, and the repeatability of the calibration results of the new method was less than 2.77”.

Effect of O2/n-C5H12 Ratio on Oxygenates Production from Plasma N-pentane Partial Oxidation

Objective: Non-thermal plasma is a promising method for producing clean fuels. This work provides a deeper understanding of the impact of O2/n-C5H12 ratio on the partial oxidation of n-pentane from both physical and chemical perspectives. Moreover, this work offers insight into improving fuel combustion efficiency and technical support for the preparation of clean fuels. Methods: An experimental system based on dielectric barrier discharge plasma was established. The discharge characteristics and product generation status of n-pentane partial oxidation were measured by changing the concentration of oxygen and n-pentane to evaluate different O2/n-C5H12 ratios. Results: Research on discharge characteristics showed that the O2/n-C5H12 ratio did not affect the discharge mode, and typical Lissajous shapes were present at different ratios. Changing the O2/n-C5H12 ratio affected the oxygen concentration, average electron energy or electron density, and background temperature. As the O2/n-C5H12 ratio increased, the conversion of the n-pentane partial oxidation reaction increased. However, changing the O2/n-C5H12 ratio did not affect the type of generated products. The oxygenates exhibited a volcano curve, and an O2/n-C5H12 ratio of 1.00 achieved the highest selectivity of 35.1%. As the O2/n-C5H12 ratio continued to increase, the selectivity of oxygenates decreased and the selectivity of CO2 increased. This was potentially due to a shift from partial oxidation toward complete oxidation, which led to the generation of secondary pollutants. Thus, higher O2/n-C5H12 ratios were not conducive to clean fuel production and environmental friendliness. Conclusion: In the partial oxidation of n-pentane, the highest clean fuel production rate was achieved when the O2/n-C5H12 ratio was 1.00. When this ratio exceeded 1.00, the reaction shifted toward complete oxidation, producing secondary pollutants. This study provides ideas for improving fuel combustion efficiency and technical support for the preparation of clean fuels.

Experimental Study of Nitinol Springs: Apparatus and Results

Abstract Background The behavior of shape memory alloys that admit large reversible deformations in response to thermal excitation has been extensively studied in recent years. Yet, the number of works dealing with springs made from these alloys is rather limited in spite of their attractiveness in various applications. Objective To bridge this gap we designed and constructed an experimental system for characterizing the behavior of the springs. It enables precise control of the three state variables: temperature, elongation, and force. Methods Control of the sample temperature is achieved by immersing it in a water-filled thermal bath, where the water temperature is adjusted using a thermoelectric Peltier device. A tension-compression motorized unit sets the spring elongation and a force gauge is used for measuring the force exerted on the spring. The data is continuously monitored and acquired with a self-coded LabVIEW program. An important aspect is the calibration procedure developed for identifying the spring load-free state and ensuring the repetitiveness of the measurements. Results Experiments in which the elongation or the force were measured as a function of the temperature demonstrate the role of the phase transformations. Isothermal experiments enabled to characterize the variations of the force versus the elongation at different temperatures. Conclusions The proposed system facilitates the execution of highly accurate experiments through which the complex history-dependent behavior of shape memory springs can be revealed and studied.

A novel NTRK1 splice site variant causing congenital insensitivity to pain with anhidrosis in a Chinese family

BackgroundCongenital insensitivity to pain with anhidrosis (CIPA, OMIM #256800), also known as hereditary sensory and autonomic neuropathy type Ⅳ (HSAN-IV), is a rare autosomal recessive disorder characterized by recurrent episodic fevers, anhidrosis, insensitivity to noxious stimuli, self-mutilating behavior and intellectual disability. CIPA can be caused by the variants in NTRK1 gene, which encodes a high-affinity tyrosine kinase receptor for nerve growth factor. To ascertain the hereditary cause of a patient with CIPA accompanied by the additional symptoms of mild growth retardation, prone to fracture, underdeveloped nails of fingers and toes, irregular tooth alignment, enamel hypoplasia, postoperative wound healing difficulty, hand and limb deformity, and dislocation of hip joint, whole exome sequencing was used and revealed a compound heterozygous variant in NTRK1.MethodsDNA was extracted from peripheral blood samples of pediatric patients and their parents, and subjected to comprehensive analysis using whole-exome sequencing (WES), followed by verification of variant sites in the NTRK1 gene through Sanger sequencing. To elucidate the functional impact of the newly discovered variants, an in vitro experimental system was established. Splicing analysis was conducted using PCR and Sanger sequencing, while expression levels were assessed through qPCR and Western blot techniques.ResultsOne hotspot variant c.851-33T>A(ClinVar ID: 21308) and a novel variant c.850 + 5G>A(ClinVar ID:3069176) was inherited from her father and mother, respectively, identified in the affected individuals. The c.850 + 5G>A variant in NTRK1 resulted in two forms of aberrant mRNA splicing: 13bp deletion (c.838_850del13, p. Val280Ser fs180) and 25bp deletion (826_850del25, p. Val276Ser fs180) in exon 7, both leading to a translational termination at a premature stop codon and forming a C-terminal truncated protein. The expression of two abnormal splicing isoforms was decreased both in the level of mRNA and protein.ConclusionIn conclusion, this study elucidated the genetic cause of a patient with CIPA and identified a novel variant c.850 + 5G>A in NTRK1, which broadened the and enriched the NTRK1 mutation spectrum.

Observation of bound valence excited electronic states of deprotonated 2-hydroxytriphenylene using photoelectron, photodetachment, and resonant two-photon detachment spectroscopy of cryogenically cooled anions.

Polycyclic aromatic hydrocarbons (PAHs) are common atmospheric pollutants, and they are also ubiquitous in the interstellar medium. Here, we report the study of a complex O-containing PAH anion, the deprotonated 2-hydroxytriphenylene (2-OtPh-), using high-resolution photoelectron imaging and photodetachment spectroscopy of cryogenically cooled anions. Vibrationally resolved photoelectron spectra yield the electron affinity of the 2-OtPh radical as 2.629(1) eV and several vibrational frequencies for its ground electronic state. Photodetachment spectroscopy reveals bound valence excited electronic states for the 2-OtPh- anion, with unprecedentedly rich vibronic features. Evidence is presented for a low-lying triplet state (T1) and two singlet states (S1 and S2) below the detachment threshold. Single-color resonant two-photon photoelectron spectroscopy uncovers rich photophysics for the 2-OtPh- anion, including vibrational relaxation in S1, internal conversion to the ground state of 2-OtPh-, intersystem crossing from S2 to T1, and a long-lived autodetaching shape resonance about 1.3eV above the detachment threshold. The rich electronic structure and photophysics afforded by the current study suggest that 2-OtPh- would be an interesting system for pump-probe experiments to unravel the dynamics of the excited states of this complex PAH anion.

Hepatocyte Intrinsic Innate Antiviral Immunity against Hepatitis Delta Virus Infection: The Voices of Bona Fide Human Hepatocytes

The pathogenesis of viral infection is attributed to two folds: intrinsic cell death pathway activation due to the viral cytopathic effect, and immune-mediated extrinsic cellular injuries. The immune system, encompassing both innate and adaptive immunity, therefore acts as a double-edged sword in viral infection. Insufficient potency permits pathogens to establish lifelong persistent infection and its consequences, while excessive activation leads to organ damage beyond its mission to control viral pathogens. The innate immune response serves as the front line of defense against viral infection, which is triggered through the recognition of viral products, referred to as pathogen-associated molecular patterns (PAMPs), by host cell pattern recognition receptors (PRRs). The PRRs–PAMPs interaction results in the induction of interferon-stimulated genes (ISGs) in infected cells, as well as the secretion of interferons (IFNs), to establish a tissue-wide antiviral state in an autocrine and paracrine manner. Cumulative evidence suggests significant variability in the expression patterns of PRRs, the induction potency of ISGs and IFNs, and the IFN response across different cell types and species. Hence, in our understanding of viral hepatitis pathogenesis, insights gained through hepatoma cell lines or murine-based experimental systems are uncertain in precisely recapitulating the innate antiviral response of genuine human hepatocytes. Accordingly, this review article aims to extract and summarize evidence made possible with bona fide human hepatocytes-based study tools, along with their clinical relevance and implications, as well as to identify the remaining gaps in knowledge for future investigations.

Hydroxylated polychlorinated biphenyls may affect the thyroid hormone-induced brain development during metamorphosis of Xenopus laevis by disturbing the expression of matrix metalloproteinases.

Thyroid hormones are primarily responsible for the brain development in perinatal mammals. However, this process can be inhibited by external factors such as environmental chemicals. Perinatal mammals are viviparous, which makes direct fetal examination difficult. We used metamorphic amphibians, which exhibit many similarities to perinatal mammals, as an experimental system. Therefore, using metamorphic amphibians, we characterized the gene expression of matrix metalloproteinases, which play an important role in brain development. The expression of many matrix metalloproteinases (mmps) was characteristically induced during metamorphosis. We also found that the expression of many mmps was induced by T3 and markedly inhibited by hydroxylated polychlorinated biphenyls (PCBs). Overall, our findings suggest that hydroxylated PCBs disrupt normal brain development by disturbingthe gene expression of mmps.

Genetic variation and pesticide exposure influence blood DNA methylation signatures in females with early-stage Parkinson’s disease

Although sex, genetics, and exposures can individually influence risk for sporadic Parkinson’s disease (PD), the joint contributions of these factors to the epigenetic etiology of PD have not been comprehensively assessed. Here, we profiled sex-stratified genome-wide blood DNAm patterns, SNP genotype, and pesticide exposure in agricultural workers (71 early-stage PD cases, 147 controls) and explored replication in three independent samples of varying demographics (n = 218, 222, and 872). Using a region-based approach, we found more associations of blood DNAm with PD in females (69 regions) than in males (2 regions, Δβadj| ≥0.03, padj ≤ 0.05). For 48 regions in females, models including genotype or genotype and pesticide exposure substantially improved in explaining interindividual variation in DNAm (padj ≤ 0.05), and accounting for these variables decreased the estimated effect of PD on DNAm. The results suggested that genotype, and to a lesser degree, genotype-exposure interactions contributed to variation in PD-associated DNAm. Our findings should be further explored in larger study populations and in experimental systems, preferably with precise measures of exposure.

Intracellular defensive symbiont is culturable and capable of transovarial, vertical transmission.

Diverse eukaryotic organisms form stable, symbiotic relationships with bacteria that provide benefits to their hosts. While these associations are often biologically important, they can be difficult to probe experimentally because intimately host-associated bacteria are difficult to access within host tissues, and most cannot be cultured. This is especially true for the intracellular, maternally inherited bacteria associated with many insects, including aphids. Here, we demonstrate that a pea aphid-associated strain of the heritable endosymbiont, Candidatus Fukatsuia symbiotica, can be grown outside of its host using standard microbiology techniques and can readily re-establish infection that is maintained across host generations. These artificial infections recapitulate the effects of native infections, making this host-symbiont pair a useful experimental system.