Exhaust Gas Recirculation Rate Research Articles

Effects of Blended Diesel-Biodiesel Fuel on Emissions of a Common Rail Direct Injection Diesel Engine with Different Exhaust Gas Recirculation Rates.

The aim of the study was to investigate the exhaust gas emissions and fuel consumption of a common rail direct injection (CRDI) diesel engine using mixed diesel (B10) and biodiesel (B20-B100) fuels. The study's primary objective was to determine the effects of blended diesel-biodiesel fuel on CRDI emissions based on different exhaust gas recirculation (EGR) rates, including carbon monoxide (CO), carbon dioxide (CO2), oxygen (O2), nitrogen oxide (NOx), and hydrocarbon (HC) emissions, smoke opacity, exhaust gas temperature, and fuel consumption. The CRDI experiments involved adjusting the different engine speeds (1400-3000 rpm) and EGR rates (0 and 12.5%), which were analyzed to determine their impact on these parameters for both blended diesel and biodiesel fuels. The results showed that under the conditions of no EGR (0%), the CO and HC emissions and the smoke opacity were lower than those with a 12.5% EGR rate for all fuel types and all cases. With 12.5% EGR rate, the O2 emissions and the EGT of the CRDI diesel engine decreased, which resulted in significantly lower NOx emissions because of EGR into the combustion chamber. For the maximum engine speed of 3000 rpm and with no EGR, the CO and HC emissions and the smoke opacity were lower than those with a 12.5% EGR rate for all fuel types. With a 12.5% EGR rate at 3000 rpm, the O2 emissions and the exhaust gas temperature were reduced by 0.07% and 2.27%, respectively, and the NOx emissions were reduced by 2.54%. However, with EGR, the CO and HC emissions and the smoke opacity increased by 7.70%, 18.61%, and 0.4%, respectively. Furthermore, the fuel consumption of pure biodiesel (B100) at 3000 rpm with a 12.5% EGR rate was reduced by 2.81% compared to that with a 0% EGR rate. Because the temperature in the combustion chamber is high enough for the engine to run, the EGR reuses a portion of the exhaust gases and can help to minimize the quantity of fuel in the combustion chamber. As a suggestion based on these observations, biodiesel fuel should not exceed B80 because the viscosity and density of fuel that are too high may affect the fuel injection system, both the injectors, and the pressure pump, causing the injectors to be unable to work correctly. These findings can contribute to the development of strategies and technologies for reducing emissions and improving fuel efficiency in CRDI diesel engines.

Effect of Variable-Nozzle-Turbocharger-Coupled Exhaust Gas Recirculation on Natural Gas Engine Emissions and Collaborative Optimization

Equivalent combustion natural gas engines typically utilize exhaust gas recirculation (EGR) systems to tackle their high thermal burden and NOx emissions. Variable nozzle turbochargers (VNT) can increase the engine intake and EGR rate simultaneously, resulting in NOx reduction while ensuring robust power performance. Using a VNT along with engine bench testing, the impact of VNT- and EGR-coordinated control on the performance and emissions of equivalent combustion natural gas engines was investigated under different operating conditions. Subsequently, multi-objective optimization was performed using a support vector machine. The results demonstrated that the use of VNTs in equivalent combustion natural gas engines could bolster the capacity to introduce EGR under several operative conditions and extend the scope of EGR regulation, thereby decreasing the engine’s thermal burden, improving fuel efficiency, and curbing emissions. Owing to the implementation of a multi-objective optimization method based on a support vector regression model and NSGA-II genetic algorithm, VNT and EGR control parameters could be optimized to slightly improve the economy and significantly reduce NOx emissions while maintaining the original engine power performance. At 20 operating points optimized for validation, brake-specific fuel consumption (BSFC) and NOx decreased by 0.94% and 47.0%, respectively, and CH4 increased by 3.7%, on average.

LQTI boost pressure and EGR rate control of a diesel air charge system with eBoost assistance

Turbocharged diesel engines often suffer significant response delay due to so-called turbo-lag, especially engines with large displacement. For this reason, many technologies have been developed to reduce turbo-lag. This paper develops a coordinated control strategy for a diesel engine equipped with an eBoost (electrical compressor) system to significantly reduce turbo-lag. A multiple-input and multiple-output (MIMO) Linear Quadratic Tracking with Integral (LQTI) control strategy, along with its scheduling logic, is developed for the Ford 6.7 L 8-cylinder diesel engine equipped with a variable geometry turbocharger (VGT), exhaust gas recirculation (EGR), and added eBoost along with a bypass valve. Note that the existing production engine does not have an eBoost and bypass valve. Multiple model-based LQTI controllers were designed at different engine operational conditions based on the associated linearized models, and the control outputs are scheduled based upon the engine load condition and bypass valve position. The developed control strategy is validated in both simulation and experimental studies, and the test results show a reduction in engine response time by up to 81.36% in terms of reaching target intake manifold (boost) pressure following a load step-up, compared with the production configuration (without eBoost and bypass valve) with no significant impact on NOx emissions.

Effect of exhaust gas recirculation(EGR) on combustion and emission of butanol/gasoline combined injection engine

N-butanol is a kind of biomass alcohol which can be produced by fermentation, and it is also a clean alternative fuel. The combustion and emissions characteristics of n-butanol/gasoline SI engine under different combined injection modes with the introduction of EGR was studied. N-butanol inlet injection plus gasoline in-cylinder direct injection is called N-GXDI; Gasoline inlet injection plus n-butanol in-cylinder direct injection is called G-NXDI. Through the analysis of combustion and emission performance under different EGR rates, injection modes and direct injection ratios (DIr), it is found that with the increase of DIr, cylinder temperature, pressure, and IMEP increase first and then decrease. Under the DIr = 50%, the combustion is more complete when the EGR rate is 5%. Under the same DIr, with the increase of EGR rate, CO emission decreased first and then increased, NOx emission opposite, THC emission increased. Under the same EGR rate, the total particle number of the two modes decreases first and then increases with the increase of DIr. The G-NXDI mode has advantages in combustion and primary emissions, while the N-GXDI mode has advantages in particulate emissions, suitable injection mode combined with EGR can greatly improve combustion and emission performance.

Integrated optimization of common rail direct injection diesel engine input parameters with linseed biodiesel: A hybrid approach using grey relational analysis and genetic algorithm techniques

In the pursuit of improved productivity and efficiency, the search for alternative fuels that reduce dependence on fossil fuels is of utmost importance. This research study aims to investigate the influence of process parameters, namely blend percentage, fuel injection pressure, exhaust gas recirculation (EGR) rate, and engine load, on various engine performance parameters such as torque, brake thermal efficiency (BTE), brake mean effective pressure (BMEP), hydrocarbon emissions (HC), and mechanical efficiency. The experiments are conducted following the Taguchi orthogonal array (L25) design of experiments. Additionally, grey relational analysis, a multi-objective optimization technique, is applied to identify the optimal levels of the process variables that optimize all the response parameters. The optimal values obtained through grey relational analysis are determined as 0% blend, 600 bar fuel injection pressure, 12% EGR rate, and 12 kg engine load. Moreover, the Genetic Algorithm-based Multi-Objective Genetic Algorithm (MOGA) is employed for multi-objective optimization of the engine input variables, yielding optimal levels of 19.45% blend, 594.35 bar fuel injection pressure, 14.12% EGR rate, and 12 kg engine load. Furthermore, multivariable regression models are developed to predict the response variables within the experimental domain. These models are validated through a confirmation test. The findings of this study provide insights into the optimization of process variables for enhanced engine performance, with the developed models serving as valuable tools for future predictions and optimization.

Study on exhaust gas recirculation diesel engine using karanja oil methyl ester with low heat rejection in direct injection

Energy is a fundamental necessity for man›s life in the digital world today. The rapid depletion of fossil fuel resources forces rigorous alternative fuel analysis. Petroleum diesel can better replace vegetable oils, edible or motored today. The rapid depletion of fossil fuel resources forces rigorous alternative fuel analysis. Petroleum diesel can better replace vegetable oils, edible or not. Karanja may be a possible supplier of diesel fuel for non-edible oil substitution. Current combustion surfaces for pistons, valves, and cylinders have been filled with ceramic materials, which make the engine totally adiabatic (LHR). The performance of a biodiesel-powered compressing ignition (CI) engine may be further boosted by utilising the engine›s heat effectively and increasing thermal efficiency. Exhaust Gas Recirculation (EGR) is actually one of the most important methods of limiting NOx emissions in internal combustion engines. Explore the output with and without exhaust gas recirculation on a retarded timing engine with diesel and karanja oil methyl ester (KOME). The LHR with a retarded timing engine yielded improved thermal brake efficiency (TBE), decreased HC, smoke, and CO emissions, while increasing KOME›s NOx in comparison with an uncoated engine. As the EGR rate grew, NOx and BTE were reduced marginally with increased HC, CO, and smoke. 24.1 g/kw-hour CO, 10.1 g/kw-hour NOx, and 0.55 g/kW-hour HC were registered at 20 percent of EGR.

Stratified premixed combustion optimization of a natural gas/biodiesel dual direct injection engine

The natural gas (NG) stratified premixed combustion mode (NSPC) demonstrates significant potential for improving thermal efficiency and lowering emissions when compared to the NG mixing-limited combustion mode (NMLC). In this study, the NSPC for a NG/biodiesel dual direct injection engine was optimized through numerical simulation. The initial evaluation of biodiesel as the pilot fuel reveals its capacity to reduce soot and CO emissions while simultaneously increasing thermal efficiency in comparison with pure diesel. The subsequent examination delved into the effects of the injection timing of biodiesel and natural gas on mixture distribution, combustion, and emissions characteristics. The findings indicates that a well-balanced combination of moderate injection timing of natural gas and slightly delayed injection timing of biodiesel results in significantly lowered CO and soot emissions while maintaining high thermal efficiency, but with a trade-off of increased NOx emissions. The engine performance was further refined through the integrated application of exhaust gas recirculation (EGR) and pilot fuel pre-injection. Achieving a high thermal efficiency of 42.5%, minimal CO emissions at 1.5 g/kWh, soot emissions below 1 × 10−4 g/kWh, and NOx emissions less than 2 g/kWh, is achieved by configuring the start of injection for natural gas and biodiesel at −56°CA ATDC and −10°CA ATDC, respectively, with a biodiesel pre-injection ratio of 30%, and an EGR rate of 36%.

Developments in the RCCI engines powered by several alternative fuel types: An overview

The perspective on internal combustion engines (ICEs) has changed because of the step-by-step decrease in oil reserves, environmental concerns, and many other reasons. However, the use of these engines will continue in the coming years. The development of ICEs has accelerated in recent years. As a result, studies on systems that can improve performance and reduce pollution in engines are carried out by many researchers. The basis of the studies carried out in this context is the change in the combustion mode. In other words, the emergence of different combustion modes is given importance by researchers. Among these, many studies have been made on the implementation of the reactivity-controlled compression ignition (RCCI) combustion mode. RCCI engine uses two different fuels. These fuels are low-reactivity (alcohol, gasoline, etc.) and high-reactivity (diesel, biodiesel, etc.) fuels. In addition, the fact that different alternative fuel types can be employed in these engines has made them popular all over the world. This review presents the results of the effects of parameters such as fuel ratio, different injection strategies, exhaust gas recirculation (EGR) rate, compression ratio, and piston geometry on the performance, emissions, and combustion behavior of RCCI engines using both conventional and alternative fuels. This study has been compiled to provide an overview of the current status of the RCCI concept and to offer benefits to researchers.

Impact of Cylinder-to-Cylinder Dispersion of Exhaust Gas Recirculation on the Three-Way Catalyst Performance and Tailpipe Emissions of Spark-Ignition Engines

Abstract New generations of spark-ignition engines include exhaust gas recirculation (EGR) to improve the engine efficiency. Depending on the design of the EGR routing, some differences in the total amount of recirculated gases that reach each cylinder can be induced. This affects the air-to-fuel ratio on each cylinder due to the combination of the different temperature and composition of the gases at the intake valve closure. As a consequence, significant deviations in the combustion process and the subsequent composition upstream the three-way catalyst can be reached. This paper explores these effects on catalyst performance and tailpipe emissions, individualizing the behavior for each regulated species. The study was performed in a four-cylinder naturally aspirated engine with Atkinson cycle and a close-coupled three-way catalyst. The most significant deterioration in conversion efficiency appeared for the nitrogen oxides, directly linked to the EGR dispersion level. In the case of carbon monoxide (CO) emissions, no significant impact was observed except at high average EGR rates, where one or more of the cylinders exceeded the EGR tolerance for that speed and load. Based on these results, a strategy where the fuel injector command is adapted to correct the air-to-fuel ratio deviations induced by the EGR was developed and implemented.

Effects of Varying Equivalence Ratios on the Combustion Efficiency Characteristic of a Dual-Fuel Compression Ignition Engine by Changing Intake Pressures and Exhaust Gas Recirculation Rates

In general, a leaner mixture condition improves combustion efficiency in compression ignition (CI) combustion using diesel. However, in the case of leaner air–fuel mixture conditions, it disturbs flame propagation in spark ignition combustion using gasoline, i.e., low reactivity fuel, causing a decrease in combustion efficiency. Since dual-fuel combustion in a CI engine typically involves the use of high- and low-reactivity fuels together, the differing reactivity conditions in the cylinder become as important as the local equivalence ratio in the cylinder. Thus, there is a need to verify the effect of a leaner mixture condition on combustion efficiency in dual-fuel CI combustion. For this reason, this study experimentally evaluates the effects of varying equivalence ratios on the combustion efficiency of gasoline/diesel dual-fueled CI combustion in a 0.4-L single-cylinder engine under low-speed (1500 rpm) and low-load (total LHV 570 J/str) conditions. To vary the equivalence ratios, intake pressures and exhaust gas recirculation (EGR) rates were, respectively, changed under the part-load condition. The results emphasize that as the equivalence ratio becomes leaner by increasing the intake pressure, combustion efficiency worsens due to the low reactivity properties and certain flame propagation modes of gasoline combustion. On the contrary, increasing the EGR rate did not significantly influence combustion efficiency, but it effectively helped reduce nitrogen oxide (NOx) emissions. Based on these results, it is concluded that optimizing dual-fuel CI combustion to suppress NOx emissions is better achieved using EGR, rather than creating a leaner mixture condition.

The combined effect of split fueling strategy and EGR on the combustion, performance, and emission characteristics of a CRDI biofuel engine

AbstractThe current research investigates the impact of a split fueling strategy combined with several flow rates of exhaust gas recirculation (EGR) on the combustion and emission characteristics of a diesel engine running on B20 waste cooking oil (WCO) biodiesel. A four‐stroke single‐cylinder common rail direct injection engine was employed for experiments. It operates with a B20 blend of WCO biodiesel at 600 bar pressure for varying pilot fueling conditions of 10%, 20%, and 30%. The B20 blend with 30% pilot fuel injection (B20P30) showed excellent performance and emission characteristics compared with B20 blend with 10% pilot fuel injection (B20P10) and B20 with 20% pilot fuel injection (B20P20). However, B20P30 had greater levels of nitrogen oxide (NOx) emissions than those by diesel. EGR discharge levels in 5% increments, ranging from 0% to 15% were introduced to address this issue. The experimental findings revealed that both cylinder peak pressure and heat release rate showed a reduction when the EGR flow rate was enhanced. The recirculation of exhaust gas into the combustion chamber led to a slight increase in the emission levels of hydrocarbon (HC), carbon monoxide (CO), and smoke, as well as a decrease in carbon dioxide (CO2). Nevertheless, the introduction of EGR significantly decreased NOx emissions by 22.94%, 35.05%, and 47.96% for EGR flow rates of 5%, 10%, and 15%, respectively, when compared with the engine operating without EGR. Overall, the two‐stage fueling strategy, B20P30 blended with 10% EGR corroborated to be beneficial in reducing NOx emissions with minimal performance penalties. Although there was a slight uptick in certain emissions, the overall trade‐off between emission reduction and performance was favorable. The culmination of this study is targeting the objectives of sustainable development goal 7 (clean energy) and goal 13 (climate action) to be achieved by 2030.

Analysing the effects of toluene percentages and exhaust gas re-circulation rates on spark-ignition engine performance and emissions

This study delves into the intricate dynamics of gaseous emissions in relation varying parameters in spark-ignition engines: gasoline-toluene blending ratios, exhaust gas re-circulation (EGR) rates, and spark timings. With increasing toluene concentrations, there was a consistent reduction in emissions, culminating in HC values of 67 ppm, CO at 0.6% volume, PM at 11 mg/m?, and NOx at 100 ppm for a 100% toluene blend. The implementation of EGR demonstrated its efficacy in mitigating NOx emissions, registering a decline to 60 ppm at a 30% EGR rate. However, the same augmentation in EGR rates witnessed an uptick in HC and CO emissions. Analysis of spark timings pinpointed an optimal advance of 30? CA bTDC at a 50% engine load, yielding minimized emissions. Conclusively, the research underscores the potential of fine-tuning engine parameters, such as fuel composition, EGR rates, and spark advance, to achieve a harmonious balance between engine efficiency and emission reductions. This study lays foundational data for further exploration and optimization in the realm of internal combustion engines.

Matching and optimization to minimize fuel consumption and NOx emission for a marine diesel engine with turbo-assisted exhaust gas recirculation

Exhaust gas recirculation (EGR) and two-stage turbocharging technology are widely used in marine diesel engines due to their advantages of reducing nitrogen oxides (NOx) emission and improving fuel economy respectively. The matching of EGR, two-stage turbocharging and diesel engine is significant to realize both advantages simultaneously. Turbo-assisted EGR (TA EGR) can achieve high EGR rate and lower fuel consumption due to a turbocharger driving EGR. In this study, a 1D model of the diesel engine with TA EGR coupling two-stage turbocharging system was established by GT-Power. A theoretical matching method was proposed based on the requirements of excess air coefficient and EGR rate. The matching laws of the coupling system were studied, and the preliminary matching results achieved good effects. A fully connected neural network was used as the optimization agent model of the 1D model, and the NSGA II algorithm was used to carry out the multi-parameter and multi-objective optimizing matching. Considering constrained and unconstrained conditions, independent optimizing matching was carried out under each single load, and the weighted brake specific fuel consumption (BSFC) and weighted NOx under all loads were taken as the target to carry out comprehensive optimizing matching. The results showed that the optimization performance is worse under constrained conditions, while TA EGR coupling adjustable two-stage turbocharging system can achieve comprehensive optimal BSFC and NOx, with weighted BSFC decreasing by 3.57% and weighted NOx decreasing by 75.28% compared with experimental results of the original engine.

Study on the Effect of Coupled Internal and External EGR on Homogeneous Charge Compression Ignition under High Pressure Rise Rate

This paper investigated the effects of exhaust gas recirculation (EGR) on homogeneous charge compression ignition (HCCI) combustion in internal combustion engines. The exhaust valve closing (EVC) timings were scanned to obtain a set of baseline operating points for HCCI, and the coupling control of the internal and external EGR was explored. The results indicate that external EGR delays HCCI ignition timing and slows down the combustion speed. As the internal EGR rate increases, the maximum external EGR ratio that can be tolerated decreases. For HCCI detonation operating points with low internal EGR rates, the addition of up to 10% of external EGR can control the pressure rise rate peak to less than 10 bar/°CA, resulting in reduced fuel consumption and increased indicated mean effective pressure (IMEP). However, for HCCI operating points with high internal EGR rates, the effect of external EGR is mainly observed in the control of the pressure rise rate, with limited increase in IMEP. Additionally, an increasing external EGR rate leads to a significant decrease in nitrogen oxide (NOx) emissions, while carbon monoxide (CO) and hydrocarbon (HC) emissions slightly increase before engine misfire occurs. These findings suggest that the coupling control of internal and external EGR should be explored further, particularly in relation to reducing the negative valve overlap (NVO) angle and improving combustion efficiency.

Incorporating of TiO2 with oxygenated fuel and post-injection strategy in CRDI diesel engine equipped with EGR: A step towards lower NOX, PM and enhance soot oxidation reactivity

A mixture of diesel, biodiesel (from algae), and butanol was mixed with nano-titanium dioxide at 50 and 100 parts per million in this study under post-injection (PI) strategy and two rates (10 % and 20 %) of exhaust gas recirculation (EGR). In the literature, few studies have investigated how PI strategies effect on engine emissions and combustion performance from mixture of B16M20 by butanol (16 %), microalgae biodiesel (15 %) and diesel with variable EGR rates. To gain a better understanding of the effects of EGR rates on diesel engines running with B16M20 mixture, this study was conducted. The final fuel type test used B16M20 treated with 50 ppm and 100 ppm of nano-TiO2. Fuel specific fuel consumption (BSFC) increased by 3 % for both diesel and B16M20 when EGR was used, but PI reversed this trend. Nanoparticles added to B16M20 blend significantly contributing in decreased BSFC to 6.47 %. 100 ppm nano-TiO2 added to 10 % of EGR, along with PI, can achieve the same or enhance better brake thermal efficiency (BTE) by 4.53 % than pure diesel. The lowest NOX levels by 26.48 % were achieved with 100 ppm nano-TO2 and B16M20 with 20 % EGR. Because of EGR's high heat capacity and dilution effect, higher EGR rates result in higher soot levels. As a result of the PI strategy, the soot levels emitted from B16M20 reduced by 28.57 % compared with diesel fuel. At PI strategy presence (W PI) and adding 100 ppm nano-TiO2 into the B16M20 blend resulted in the lowest PM concentrations by 59 % compared to the diesel and without PI (W/O PI). PM emissions were significantly reduced at temperatures below 600 °C from B16M20 blend combustion with delay injection, 10 % EGR, and 100 ppm nano-TiO2. Soot oxidation was minimized through EGR, and enhanced by nano-TiO2. Adding this 100 ppm of nanoparticles to diesel fuel produced more reactive soot than diesel fuel alone.

Influence of cooling loss on the energy and exergy distribution of heavy-duty diesel engines based on two-stage variable supercharging, VVT, and EGR

The application of mechanisms such as exhaust gas recirculation (EGR) coupled with variable valve timing (VVT) and a variable geometry turbocharger (VGT) can improve engine efficiency; however, the energy laws and loss distribution after EGR, VVT, and VGT changes are unclear, restricting the optimization of engine structures and corresponding strategies. Herein, a six-cylinder engine is studied, revealing that the cooling loss of the high-pressure (HP) EGR loop is an important factor affecting the engine energy distribution. The cooling loss accounts for 10.00%–20.00% of the total energy, with an average increase of 1.73%, surpassing other energy losses growth rates. The low-pressure (LP) EGR loop considerably reduces cooling losses. The cooling loss of the LP EGR loop is only 64.05% of the HP EGR loop at a 20% EGR rate. When the EGR rate is >10%, the resulting lower cooling losses effectively improve the engine efficiency and the indicated thermal efficiency (ITE) of the LP EGR loop is 0.20%–0.33% higher than that of the HP EGR loop; when the EGR rate is 21%, the ITE of the LP EGR loop reaches 49.52%. By studying the variation in exergy with operating parameters, it is found that while increasing the EGR rate from 15% to 20%, the proportion of available exergy increases by adjusting the VVT to −85° crank angle after top dead center (CA ATDC) or adjusting the VGT to 47.5% under the original operating scheme of the LP EGR loop (−146° CA ATDC; VGT = 42.5%). The available exergy increases from 71.22%–71.42% (−146° CA ATDC; VGT = 42.5%; original device) to 71.88%–71.58% (−146° CA ATDC; VGT = 47.5%) and 72.02%–72.21% (−85° CA ATDC; VGT = 42.5%). This study explores the energy distribution under different operating schemes, providing theoretical guidance for further improving the thermal efficiency of the entire device.

Study on Control Strategies on NOX Emissions to Meet Real Driving Emissions.

The aim of this study was to fulfill the NOx emissions standards for a light-duty diesel vehicle under real driving emissions (RDE) testing conditions by implementing various control strategies. In this study, RDE tests were performed by adjusting the air mass quantity and postinjection quantity in order to analyze engine-out and tail-pipe nitrogen oxides (NOx) emissions for different phases of RDE. The results showed that reducing in air mass quantity enabled the engine to operate in higher exhaust gas recirculation (EGR) rate regions, resulting in a 32.5% reduction in engine-out NOx emissions and an 80.4% decrease in tail-pipe NOx emissions. Increasing the postinjection quantity primarily enhanced the NOx conversion efficiency for the urban phase by 7.5%, leading to a 22.6% reduction in tail-pipe NOx emissions. By employing both strategies, vehicles can comfortably meet the CN6b emission regulations by a substantial margin.

Performance, emission, combustion, exergy, exergoeconomic and sustainability analyses of EGR incorporated CI engine fuelled with areca nut husk nano-additive dosed plastic oil–water-diesel emulsion blend

This first-of-a-kind research emphasizes the influence of exhaust gas recirculation (EGR) on engine characteristics, and exergy, sustainability, and exergoeconomic aspects of compression ignition engine, powered by plastic grocery bag-extracted plastic oil-diesel-water emulsion blend dosed with bio-nano-additive extracted from areca nut husk (D10EPO-15 ppm). Three EGR rates (5%, 10%, and 15%) were incorporated at varying engine loads. At 100% load, the EGR incorporation reduced the peak heat release rate and peak pressure up to 6.5 and 5.6%, respectively, in comparison to the base fuel without EGR. Up to 5.2 and 9.1% reduction in exhaust gas temperature and nitrogen oxide emission (NOx) was noticed with the EGR incorporation. However, carbon monoxide (CO), hydrocarbon (HC), and smoke emissions increased with the EGR incorporation. Nevertheless, considering the overall characteristics, 5% EGR was the most suitable one to have a lower NOx (3.4%) with a minimum penalty on CO (4.3%), HC (5.4%), and smoke (3.6%) emissions as well as fuel consumption (3%), at full load. Amongst the three EGR rates, 5% EGR incorporation also has the highest exergy efficiency (20.9%) and sustainability index (1.26). Exergoeconomic analysis also revealed the favorability of 5% EGR, and at full load, 5% EGR showed the lowest specific exergy cost inflow rate (0.8957 $/hr), the lowest specific exergy cost rate for shaft work (75.27 $/GJ), the lowest relative cost difference (3.99), and the highest exergoeconomic factor (9.95%).

Low-carbon fuels for spark-ignited engines: A comparative study of compressed natural gas and liquefied petroleum gas on a CFR engine with exhaust gas recirculation

Decades of work on low-carbon fuels have established their potential for substantial emissions reductions; however, their adoption is still limited by infrastructure concerns and engine efficiency deficits. As infrastructures have begun to evolve, research on strategies that maximize engine efficiency through interactions with fuel properties must also now take center place. This paper compares the performance, emissions, and combustion characteristics of two forefront low-carbon fuels: compressed natural gas (CNG) and liquefied petroleum gas (LPG) in a cooperative fuel research (CFR) engine over a range of compression ratios and engine loads. The effects of exhaust gas recirculation (EGR), end-gas auto-ignition, and a novel combustion control tool, the combustion intensity metric (CIM), were also evaluated at different stoichiometric engine operating conditions. In comparison to LPG, CNG operation demonstrated an extended knock-free regime, allowing engine operation at higher engine loads and compression ratios, but LPG operation exhibited enhanced combustion characteristics with higher peak pressures and faster apparent heat release rates (AHRR). LPG operation achieved higher brake thermal efficiencies and lower equivalent CO2 emissions compared to CNG operation at the tested engine loads and compression ratios. LPG demonstrated significantly higher EGR tolerance limits compared to CNG, with a maximum of 28% EGR rate, compared to 23% for CNG. This improved EGR dilution tolerance was responsible for a 90% reduction in NOx emissions for LPG compared to a maximum of 70% with CNG. EGR dilution also exhibited more effective knock mitigation potential with LPG, suppressing knock intensity values by up to 98% and transitioning the engine operation towards normal combustion from heavy knocking conditions. The CIM was found to decrease burn durations and improve the quality of combustion by controlling the desired fraction of end-gas auto-ignition.

Numerical study of effect of post injection coupled with EGR on combustion and emission performances of CRDI engine fueled with biodiesel-ethanol blends

Energy shortage and environmental pollution are becoming more serious, biodiesel is regarded as the most promising alternative fuel for diesel engines due to its environmentally friendly and renewable characteristics. In this study, the biodiesel-ethanol blends were used in a diesel engine, and the purpose of the study was to simultaneously control the NOx and soot emissions of the diesel engine by adjusting the injection strategy and EGR rate. A turbocharged, six-cylinder, common rail direct injection (CRDI) engine model was established using GT-Power. The effects of the main-post injection strategy and post injection coupled with exhaust gas recirculation (EGR) on combustion and emission characteristics were investigated at a maximum torque speed and a medium load. The results show that when the main-post injection strategy is employed, the combustion duration of the main injection is shortened with an increase in the main-post injection interval (MPI). When the MPI increased to more than 18 °CA, the heat release of post injection could be observed clearly from the curve of the heat release rate, NOx emissions decreased by 5.70% and 7.12%, respectively, and soot emissions decreased by 25.56% and 30.20%, respectively. Moreover, with the increasing post injection quantity, the combustion duration of the main injection shortened, and the peak heat release rate (PHRR) of the post injection increased. When the fuel quantity for the post injection increased from 2 to 6 mg, NOx emissions decreased from 2.33% to 9.80%, and soot emissions decreased from 16.10% to 34.97%. The effect of post injection quantity on emissions was more significant than that of the MPI. In addition, with increasing EGR rate, the ignition delay is prolonged, the peak cylinder pressure, PHRR, peak combustion temperature and NOx emissions decrease, whereas soot emissions increase gradually. Main-post injection can improve the NOx-soot trade-off, the optimal EGR rate is 22.86% under a post injection quantity of 4 mg and a MPI of 22 °CA.