Ethylenediaminetetraacetic Acid Research Articles

Indium Tin Oxide Induced Internal Positive Feedback and Indium Ion Transport in Perovskite Solar Cells.

Stability is the most pressing challenge hindering the commercialization of perovskite solar cells (PSCs), and previous efforts focused more on enhancing the resistance of PSCs to external stimulus. Here, we found that the indium tin oxide (ITO) will deteriorate the photovoltaic performance of PSCs through positive feedback cycles. Specifically, the perovskite degradation products will cross the electron transport layer to chemically etch the electrode ITO to generate In3+, which will migrate upwards into the perovskite film. Then, the reaction that corrodes ITO consumes the decomposition products of perovskite and shifts the balance of the perovskite decomposition reaction, further promoting the degradation and thus falling into a positive feedback cycle. Moreover, the In3+ in the perovskite film was found to accumulate at the upper surface, which would lead to n-type doping of perovskite film to form the energy barrier for interface carrier extraction. Subsequently, the chelating molecule ethylenediaminetetraacetic acid disodium salt (EDTA-2Na) was introduced onto ITO to firmly chelate the In3+ and prevent it from migrating upward, thus breaking this internal positive feedback cycle and significantly enhancing the efficiency and stability of PSCs. This work provides new perspectives for understanding the mechanism of photovoltaic performance loss and ionic transport in PSCs.

Indium Tin Oxide Induced Internal Positive Feedback and Indium Ion Transport in Perovskite Solar Cells

AbstractStability is the most pressing challenge hindering the commercialization of perovskite solar cells (PSCs), and previous efforts focused more on enhancing the resistance of PSCs to external stimulus. Here, we found that the indium tin oxide (ITO) will deteriorate the photovoltaic performance of PSCs through positive feedback cycles. Specifically, the perovskite degradation products will cross the electron transport layer to chemically etch the electrode ITO to generate In3+, which will migrate upwards into the perovskite film. Then, the reaction that corrodes ITO consumes the decomposition products of perovskite and shifts the balance of the perovskite decomposition reaction, further promoting the degradation and thus falling into a positive feedback cycle. Moreover, the In3+ in the perovskite film was found to accumulate at the upper surface, which would lead to n‐type doping of perovskite film to form the energy barrier for interface carrier extraction. Subsequently, the chelating molecule ethylenediaminetetraacetic acid disodium salt (EDTA‐2Na) was introduced onto ITO to firmly chelate the In3+ and prevent it from migrating upward, thus breaking this internal positive feedback cycle and significantly enhancing the efficiency and stability of PSCs. This work provides new perspectives for understanding the mechanism of photovoltaic performance loss and ionic transport in PSCs.

Effects of fixation and demineralization on histomorphology and DNA amplification of canine bone marrow.

Fixation and demineralization protocols for bone marrow (BM) across diagnostic laboratories are not standardized. How different protocols affect histomorphology and DNA amplification is incompletely understood. In this study, 2 fixatives and 3 demineralization methods were tested on canine BM samples. Twenty replicate sternal samples obtained within 24 hours of death were fixed overnight in either acetic acid-zinc-formalin (AZF) or 10% neutral-buffered formalin (NBF) and demineralized with formic acid for 12 hours. Another 53 samples were fixed in AZF and demineralized with hydrochloric acid for 1-hour, formic acid for 12 hours, or ethylenediamine tetraacetic acid (EDTA) for 24 hours. Histologic sections were scored by 4 raters as of insufficient, marginal, good, or excellent quality. In addition, DNA samples extracted from sections treated with the different fixation and demineralization methods were amplified with 3 sets of primers to conserved regions of T cell receptor gamma and immunoglobulin heavy chain genes. Amplification efficiency was graded based on review of capillary electrophoretograms. There was no significant difference in the histomorphology scores of sections fixed in AZF or NBF. However, EDTA-based demineralization yielded higher histomorphology scores than demineralization with hydrochloric or formic acid, whereas formic acid resulted in higher scores than hydrochloric acid. Demineralization with EDTA yielded DNA amplification in 29 of 36 (81%) samples, whereas demineralization with either acid yielded amplification in only 2 of 72 (3%) samples. Although slightly more time-consuming and labor-intensive, tissue demineralization with EDTA results in superior morphology and is critical for polymerase chain reaction (PCR) amplification with the DNA extraction method described in this article.

Luminescent Silicon Nanocrystals as Metal Ion Sensors.

At relatively low concentrations in aqueous solution, Fe3+, Fe2+, Cu2+, and Ni2+ quench the photoluminescence (PL) of the undecenoic acid-capped silicon (Si) nanocrystals. The PL could be restored by adding a chelating agent, such as ethylenediaminetetraacetic acid (EDTA), to remove the ions. Fe3+ and Cu2+ also significantly increase the PL lifetime. Other metal ions, including Cd2+, Mn2+, Pb2+, Zn2+, In3+, K+, and Ca2+, had no effect on the Si nanocrystal PL. The limits of detection (LODs) for Fe3+ and Cu2+ of 370 and 150 nM, respectively, are low enough for metal ion sensing applications.

Biochemical characterization of purified phytase produced from Aspergillus awamori AFE1 associated with the gastrointestinal tract of longhorn beetle (Cerambycidae latreille)

ABSTRACT The need for industrially and biotechnologically significant enzymes, such as phytase, is expanding daily as a result of the increased use of these enzymes in a variety of operations, including the manufacture of food, animal feed, and poultry feed. This study sought to characterize purified phytase from A. awamori AFE1 isolated from longhorn beetle for its prospect in industrial applications. Ammonium sulfate precipitation, ion-exchange chromatography, and gel-filtration chromatography were used to purify the crude enzyme obtained from submerged fermentation using phytase-producing media, and its physicochemical characteristics were examined. The homogenous 46.8-kDa phytase showed an 8.1-fold purification and 40.7% recovery. At 70 C and pH 7, the optimum phytase activity was noted. At acidic pH 4–6 and alkaline pH 8–10, it likewise demonstrated relative activity of 88–95% and 67–88%, respectively. It showed 67–70% residual activity between 30 and 70 C after 40 min, and 68–94% residual activity between pH 2 and 12 after 2 h. The presence of Hg+, Mg2+, and Al3+ significantly decreased the enzymatic activity, whereas Ca2+ and Cu2+ enhanced it. Ascorbic acid increased the activity of the purified enzyme, whereas ethylenediaminetetraacetic acid (EDTA) and mercaptoethanol inhibited it. The calculated values for Km and Vmax were 55.4 mM and1.99 μmol/min/mL respectively. A. awamori phytase, which was isolated from a new source, showed unique and remarkable qualities that may find use in industrial operations such as feed pelleting and food processing.

Sealing ability of various endodontic sealers with or without ethylenediaminetetraacetic acid (EDTA) treatment on bovine root canal.

This study investigated the wettability and consistency of various endodontic sealers, both inorganic and organic, and evaluated their sealing ability of root canals using the single-cone obturation technique, with and without ethylenediaminetetraacetic acid (EDTA) treatment. Bovine root canals were endodontically prepared and filled in preparation for the dye penetration test with toluidine blue solution. All sealers exhibited contact angles similar to or lower than dentin and displayed superior consistency. Among the sealers, organic sealers used without EDTA treatment showed reduced dye penetration compared to inorganic sealers. However, some inorganic and organic sealers showed dye penetration in the sealer and dentin of root canals subjected to EDTA treatment. In conclusion, the single-cone obturation technique, combined with these endodontic sealers, achieved close contact with root canal dentin due to their wettability and consistency. However, the sealing ability of certain sealers was influenced by EDTA treatment.

Formation Mechanism and Morphology Evolution of β-NaYF4 Single Microcrystals in Hydrothermal Process

Lanthanide-doped upconversion (Ln-doped UC) materials with predicable phase and geometry are attractive for their promising application in optics and biological. Herein, we report a facile strategy for deterministic synthesis of β-NaYF4 microcrystals by an ethylenediaminetetraacetic acid (EDTA) assisted hydrothermal process. The nucleation and growth process of the β-NaYF4 microcrystals have been experimentally revealed with different hydrothermal times. The phase and geometry of as-obtained crystals can be well manipulated by the experimental parameters such as pH values, precursors’ ratio, and reactant concentrations. The formation and morphology evolution mechanism of β-NaYF4 single microcrystals can be qualitatively analyzed using energy minimization principles under the thermodynamic and kinetic control. In addition, we presented the colour-changing up-conversion of Tm3+ and Yb3+ doped single β-NaYF4 microrod. Our work could help the understanding on crystal growth and design of rare earth fluoride mateirals at micro and nanoscale.

Oxide-Encapsulated Silver Electrocatalysts for Selective and Stable Syngas Production from Reactive Carbon Capture Solutions.

Electrolysis of bicarbonate-containing CO2 capture solutions is a promising approach towards achieving low-cost carbon-neutral chemicals production. However, the parasitic bicarbonate-mediated hydrogen evolution reaction (HER) and electrode instability in the presence of trace impurities remain major obstacles to overcome. This work demonstrates that the combined use of titanium dioxide (TiO2) overlayers with the chelating agent ethylene diamine tetra-acetic acid (EDTA) significantly enhances the selectivity and stability of Ag-based electrocatalysts for bicarbonate electrolysis. The amorphous TiO2 overlayers suppress the HER by over 50% at potentials more negative than -0.7 V vs. RHE, increasing the CO faradaic efficiency (FE) by 33% (relative). In situ surface-enhanced Raman spectroscopy (SERS) measurements reveal the absence of near-surface bicarbonate species and an abundance of CO2 reduction intermediates at the Ag|TiO2 buried interface, suggesting that the overlayers suppress HER by blocking bicarbonate ions from reaching the buried active sites. In accelerated degradation tests with 5 ppm of Fe(III) impurity, the addition of EDTA allows stable CO production with >47% FE, while the electrodes rapidly deactivate in the absence of EDTA. This work highlights the use of TiO2 overlayers for enhancing the CO:H2 ratio while simultaneously protecting electrocatalysts from impurities likely to be present in "open" carbon capture systems.

Differences in Cardiac Troponin T Composition in Myocardial Infarction and End-Stage Renal Disease Patients: A Blood Tube Effect?

Cardiac troponin T (cTnT) is key in diagnosing myocardial infarction (MI) but is also elevated in end-stage renal disease (ESRD) patients. Specific larger cTnT proteoforms were identified for the acute phase of MI, while in serum of ESRD patients solely small cTnT fragments were found. However, others allocated this to a pre-analytic effect due to abundant thrombin generation in serum. Therefore, we investigated the effect of various anticoagulation methods on cTnT composition and concentration and compared the cTnT composition of MI and ESRD patients. The agreement of cTnT concentrations between simultaneously collected serum, lithium-heparin (LH) plasma, and ethylenediaminetetraacetic acid (EDTA) plasma was studied using the high-sensitivity (hs-)cTnT immunoassay. cTnT proteoform composition was investigated in a standardized time-dependent manner through spike experiments and in simultaneously collected blood matrixes of MI and ESRD patients. Excellent hs-cTnT concentration agreements were observed across all blood matrixes (slopes > 0.98; 95% CI, 0.96-1.04). Time-dependent degradation (40 kDa intact:29 kDa fragment:15 to 18 kDa fragments) was found in LH plasma and EDTA plasma, and serum in ratios (%) of 90:10:0, 0:5:95, and 0:0:100, respectively (48 h after blood collection). Moreover, gel filtration chromatography (GFC) profiles illustrated mainly larger cTnT proteoforms in MI patients, while in ESRD patients mainly 15 to 18 kDa fragments were found for all matrices. The extent of cTnT degradation in vitro is dependent on the (anti)coagulation method, without impacting hs-cTnT concentrations. Furthermore, mainly larger cTnT proteoforms were present in MI patients, while in ESRD patients mainly small 15 to 18 kDa cTnT fragments were found. These insights are essential when developing a novel hs-cTnT assay targeting larger cTnT proteoforms.

Effect of blood collection tube containing protease inhibitors on the pre-analytical stability of Alzheimer's disease plasma biomarkers.

The reliability of plasma biomarkers of Alzheimer's disease (AD) can be compromised by protease-induced degradation. This can limit the feasibility of conducting plasma biomarker studies in environments that lack the capacity for immediate processing and appropriate storage of blood samples. We hypothesized that blood collection tube supplementation with protease inhibitors can improve the stability of plasma biomarkers at room temperatures (RT). In this study, we conducted a comparative analysis of blood biomarker stability in traditional ethylenediaminetetraacetic acid (EDTA) tubes versus BD™ P100 collection tubes, the latter being coated with a protease inhibitor cocktail. The stability of six plasma AD biomarkers was evaluated over time under RT conditions. We evaluated three experimental approaches. In Approach 1, pooled plasma samples underwent storage at RT for up to 96 h. In Approach 2, plasma samples isolated upfront from whole blood collected into EDTA or P100 tubes were stored at RT for 0 h or 24 h before biomarker measurements. In Approach 3, whole blood samples were collected into paired EDTA and P100 tubes, followed by storage at RT for 0 h or 24 h before isolating the plasma for analyses. Biomarkers were measured with Single Molecule Array (Simoa) and immunoprecipitation-mass spectrometry (IP-MS) assays. Both the IP-MS and Simoa methods revealed that the use of P100 tubes significantly improves the stability of Aβ42 and Aβ40 across all approaches. However, the Aβ42/Aβ40 ratio levels were significantly stabilized only in the IP-MS assay in Approach 3. No significant differences were observed in the levels of plasma p-tau181, GFAP, and NfL for samples collected using either tube type in any of the approaches. Supplementation of blood collection tubes with protease inhibitors could reduce the protease-induced degradation of plasma Aβ42 and Aβ40, and the Aβ42/40 ratio for the IP-MS assay. These findings have crucial implications for preanalytical procedures, particularly in resource-limited settings.

Morphology-transforming AuNPs-based fluorescent probe for ultra-low sensitive detection of levofloxacin in urine samples at pH 7.0 through excimer formation

Fluorescent metal nanoparticles (MNPs) have garnered considerable interest in the realm of healthcare applications. Within this domain, we present a novel fluorescent sensor: Pamoic acid (PA) functionalized excitation-dependent gold nanoparticles (PA@AuNPs), designed to ascertain levofloxacin (LF) concentrations in human urine samples under pH 7.0 conditions. The synthesis of PA@AuNPs was achieved via a chemical reduction method employing PA as both a reducing and stabilizing agent. Validation of the successful synthesis of PA@AuNPs was conducted utilizing a suite of analytical techniques including X-ray diffraction (XRD), ultraviolet–visible absorption spectroscopy (UV–Vis), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). Microscopic examination via field emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HRTEM) elucidated the spherical morphology of PA@AuNPs, with an average diameter ranging from 10 to 15 nm. Furthermore, atomic force microscopy (AFM) revealed an average surface roughness of 20.72 nm for PA@AuNPs. Thermal analysis results divulge that PA@AuNPs are highly stable up to 370 °C. The PA@AuNPs have shown more than 10-fold higher selectivity for LF in comparison with other commercially available antibiotics. The fluorescence emission intensity of PA@AuNPs (quantum yield (ΦF) 3.36 %) has shown enhanced redshift (436 → 497 nm; ∼61 nm) (λex 353 nm) upon the sequential addition of LF (0 → 100 µM) and achieved a lower detection limit (LoD = 36 nM; LoQ = 121 nM; Ka = 1.0457 × 104 M−1) with increased ΦF 18.96 %. This radiative process and fluorescence enhancement were confirmed by time-correlated single photon counting (TCSPC) measurement (4.89 → 5.36 ns). Interestingly, upon sensing LF, PA@AuNPs changed their morphology from spherical to octahedron and displayed an excimer formation through intermolecular π-π stacking. Furthermore, the stability of the complex, PA@AuNPs•LF which formed through coordination, by restoring the fluorescence intensity of PA@AuNPs•LF (turn on) in the presence of ethylenediamine tetraacetic acid (EDTA) (turn off) is demonstrated. The formation of the PA@AuNPs•LF complex was further confirmed by XRD analysis and FTIR spectroscopy. The HRTEM and FESEM validate that PA@AuNPs•LF have octahedral morphology with an average size of 20–30 nm, and the obtained moiré fringes in TEM images are due to the overlap of LF on the surface of PA@AuNPs. The AFM analysis divulges that PA@AuNPs•LF had a larger surface roughness (Sa = 26.91 nm). The experimentally attained zeta potential of PA@AuNPs (–12.6 mV) was further decreased (–17.6 mV) in the presence of LF, which confirms the interaction between PA@AuNPs and LF. The cell viability (82 %) in L929 Fibroblast cells augmented the biological applications of PA@AuNPs. The practicability of the fluorescent sensor probe was demonstrated in human urine samples with recovery ranges from 97.56 to 104.38 %.

In Situ Modification of Activated Carbon Made from Camellia oleifera Shell with Na2EDTA for Enhanced La3+ Recovery

It is important to recover La3+ from metallurgical solutions or wastewater. However, the recovery rate of La3+ is usually less than 1% and the recovery methods are not environmentally friendly or user-friendly. Therefore, a straightforward, efficient, clean, and economically friendly method is needed. In this investigation, a modified adsorbent, COSAC-Na2EDTA-15, which was made from the Camellia oleifera shell (COS) and disodium ethylenediaminetetraacetic acid (Na2EDTA), was invented. In addition, characterization of the COSAC-Na2EDTA-15 adsorbent was conducted using SEM and XPS, and the principle of adsorption was revealed. The adsorption kinetics followed P-S-O KM, while the isotherm of COS-activated carbon (COSAC) aligned more closely with the Langmuir model. Compared to COSAC, the maximum La3+ adsorption capacity of COSAC-Na2EDTA-15 increased from 50 to 162.43 mg/g, and the content of O and N changed from 7.31% and 1.48% to 12.64% and 4.15%, respectively. The surface of the COSAC-Na2EDTA-15 exhibited abundant C, N, and O elements, and La3+ was detected on the sample surface after adsorption. The test and analysis results fully indicate that La3+ can be successfully adsorbed on the surface of COSAC-Na2EDTA-15. Because of its easy preparation, low cost, and superior performance, activated carbon made from COS finds extensive applications in the adsorption and recovery of rare earth elements.

Vacancy controlled MoSSe/MnSe heterostructure show boosting activities in photoelectrochemical and electrocatalytic hydrogen production

There are many factors that affect the activity of catalyst, such as the absorption capacity of catalyst itself, carrier separation, active site and surface transfer efficiency. In the study of this paper, two main influencing factors of catalyst are considered. One is that the electronic band structure determines the carrier separation and transport efficiency; the other is surface chemical state affects the active sites. A vacancy controlled MoSSe/MnSe heterojunction catalyst was demonstrated: MoSSe formed a type II heterojunction with MnSe, allowing photo generated carriers to move between the conduction and valence bands of the two semiconductors, thereby improving separation efficiency. Under the optimized MnSe composite ratio, MSMS3 exhibited a photocurrent density of up to −7.153 mA/cm2 at 0 V vs RHE, which is 5.2 times that of the MoSSe. In addition, the catalyst was further treated with ethylene diamine tetraacetic acid (EDTA). Due to the weak binding between Mn and Se, a large number of Mn atoms detach and form many Mn vacancies (VMn) on the catalyst surface due to the complexation effect of EDTA. These vacancies provide a large number of active sites, reduce of the adsorption energy barrier for H* which greatly enhancing the activity of the catalyst in hydrogen evolution reactions. Compared with the original MoSSe (overpotential 476 mV, Tafel slope 216 mV/dec), the overpotential of the vacancy catalyst MSMS3v is reduced to 197 mV with a Tafel slope of 77 mV/dec. This work demonstrates a novel catalyst regulation strategy.

Mathematical modeling of rare earth element separation in electrodialysis with adjacent anion exchange membranes and ethylenediaminetetraacetic acid as chelating agent

This research delves into the effective use of electrodialysis for the separation of rare earth elements (REEs), specifically separating dysprosium (Dy) from praseodymium (Pr) and neodymium (Nd). A robust mathematical model based on the extended Nernst-Planck equation is introduced, simulating the process within a configuration that includes two adjacent anion exchange membranes. The model integrates aspects such as feed equilibrium, ion exchange within the membrane, and overall ion flux. Validation of the model's predictability was conducted through Chi-squared tests and root mean square error (RMSE) calculations, affirming its capability to accurately predict ion concentrations across different compartments. The study examines essential parameters such as applied voltage, rinse solution concentration, and feed concentration, assessing their impacts on separation performance and energy efficiency. Results indicate that higher voltages above 8 V, while speeding up separation, detrimentally impact energy use. It also highlights a critical balance in rinse solution concentration; lower concentrations below 0.05 mol/L enhance energy efficiency but may undercut separation efficacy due to early depletion. A linear correlation between the necessary rinse concentration and feed concentration was established, with higher feed concentrations demonstrating reduced specific energy consumption, thus enhancing overall efficiency. However, challenges remain in current efficiency due to the independent migration of SO42− ions in this specific setup. The findings advocate exploring alternative configurations, like alternating cation and anion exchange membranes, to optimize both environmental and economic aspects of REE separation. This study provides valuable insights and recommendations for refining electrodialysis systems in REE processing, contributing to sustainable and cost-effective electrodialysis systems.

Comparative effects of 17% ethylenediaminetetraacetic acid and 9% etidronic acid applied with different irrigant activation techniques on the release of growth factors from dentin: in vitro study.

Growth factors embedded in the extracellular matrix of the dentin play an important role in the migration, proliferation, and differentiation of dental pulp stem cells in regenerative endodontics. In regenerative endodontic treatments, the type of irrigation solution used is crucial for the release of growth factors (GFs) from the dentin matrix. This study evaluated the effectiveness of different irrigant activation techniques (IAT) using two different chelating agents, 17% ethylenediaminetetraacetic acid (EDTA) and 9% etidronic acid (HEDP), in terms of their GF release. Seventy-two mandibular premolar teeth were prepared to simulate an open apex. The root fragments were irrigated with 20ml of 1.5% sodium hypochlorite and 20ml of saline solution. Eight root fragments were randomly separated for the control group, and the remaining 64 fragments were randomly separated into eight groups based on two different chelating agents (17% EDTA and 9% HEDP) and four different IAT ((conventional needle irrigation (CNI), passive ultrasonic irrigation (PUI), sonic activation with EDDY, and XP-endo Finisher (XPF)). TGF-β1, VEGF-A, BMP-7 and IGF-1 release levels were determined using an ELISA, and statistical analysis was performed using the Kolmogorov-Smirnov test, ANOVA, and the Tukey test (p < .05). Compared to the control group, the experimental groups showed significantly higher GF release when using EDTA or HEDP. Among the activation groups, the EDDY group triggered the highest GF release, and the CNI group triggered the lowest. IAT with EDTA and HEDP can increase GF release, with EDDY being the most effective IAT method. Using chelating agents with IAT may be beneficial in regenerative endodontic treatments.

EDTA functionalized pine needle biochar (EDTA@BC); a valorized bio-material for removal of Ni(II) from aqueous solution.

The preparation of ethylenediaminetetraacetic acid (EDTA) functionalized pine needles biochar (EDTA@BC) as a low-cost active adsorbent and its effectiveness in removing Ni(II) from aqueous solution at various conditions is reported in this paper. First, alkali activation was selected to render the pine needle biochar with an excellent porous structure and increased concentration of hydroxyl groups to facilitate grafting. Subsequently, a simple method was utilized to graft EDTA onto the biochar. The prepared EDTA@BC was characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and energy dispersive x-ray spectrometry (EDX). Batch adsorption studies were conducted to assess the impact of various parameters such as solution pH, adsorbent dosage, adsorbate volume, and shaking time on the removal efficiency of Ni(II). At pH 6, 100 mg dosage, 4 mL of adsorbate volume, and 10 min of shaking time, the maximum removal efficiency of Ni(II) was observed to be 89%. EDTA@BC showed reasonable sorption performance still after the third cycle of regeneration. The effect of interfering ions such as Pb, Cr, Cu, and Hg was evaluated, resulting a decrease of 69%, 78%, 76%, and 68%, respectively, in its sorption capacity. The Langmuir model provided a better fit for Ni(II) in the concentration range of 0.1-2000 ppm under optimized conditions, with qmax of 46.69 ± 1.031 mg/g and KL of 0.001, compared with the Freundlich isotherm, which yielded n = 0.234 and χ2 = 2.7899, Temkin isotherm (R2 = 0.9520), and Redlich-Peterson isotherm (R2 = 0.9725). The removal of Ni(II) by EDTA@BC was found to be the pseudo-second-order kinetics. Thermodynamic studies indicated adsorption process to be endothermic and nonspontaneous. Hence, a sustainable valorized bio-material (EDTA@BC) is prepared having better sorption efficiency of Ni(II) from aqueous solution with possible wide applicability. RESEARCH HIGHLIGHTS: New EDTA functionalized indigenous pine needles biochar (EDTA@BC) was prepared. This low-cost active adsorbent found effective in removing Ni(II) from aqueous solution. FTIR, SEM, and EDX proved synthesis and uptake of Ni(II) from aqueous solution. Ni(II) removal, regeneration, interfering and adsorption studies were performed by UV-Vis spectroscopy.

Influence of different endodontic irrigants on shear bond strength of composite resin to coronal dentin: An in vitro study

Objectives: Endodontic irrigants are critical in root canal treatments, but their influence on the coronal dentin bond strength of composite restorations is a key concern for a favorable clinical prognosis. The present in vitro study explores the effect of different endodontic irrigants on shear bond strength of composite resin. Material and Methods: Fifty permanent human mandibular molars were sectioned to expose coronal dentin and divided into five groups. Each group received a specific irrigant treatment before composite resin bonding. Shear bond strength was examined using Instron Universal testing machine, and statistical analysis was conducted using post hoc Tukey’s test and analysis of variance. Results: Group A (Saline) showed a mean shear bond strength of 18.5 Megapascal (MPa). Group B [sodium hypochlorite (NaOCl)] had mean shear bond strength of 15.2 MPa. Group C [Chlorhexidine (CHX) Gluconate] exhibited mean shear bond strength of 20.3 MPa. Group D ethylenediaminetetraacetic acid (EDTA) recorded mean shear bond strength of 14.8 MPa, while Group E [citric acid (CA)] had the highest mean shear bond strength at 22.7 MPa. Conclusion: The type of endodontic irrigant used significantly affected the shear bond strength of composite restorations to coronal dentin. CHX gluconate and CA displayed superior bond strengths compared to Saline, NaOCl, and EDTA. This underscores the importance of irrigant selection in achieving successful composite restorations in endodontically treated teeth.

99mTc-DTPA dynamic SPECT/CT renogram in adults: feasibility and diagnostic benefit.

The objective of this study is to investigate the feasibility and potential advantages of 99mTc-DTPA dynamic single photon emission computed tomography/computed tomography (SPECT/CT) renogram in adults. Fifty-five patients aged 19-80 years (mean 56.3) were enrolled. The imaging protocol included: day 1: 99mTc-DTPA planar renogram, followed by planar 99mTc-DMSA scan. Day 3: attenuation-corrected dynamic 99mTc-DTPA SPECT renogram [DSPECT(AC)] and Cr-51 ethylenediamine tetraacetic acid (EDTA) glomerular filtration rate (GFR) calculation. DSPECT(AC) included an initial CT scan followed by 12 consecutive SPECT sessions acquired via continuous-mode acquisition for a total of 24 min. Fast SPECT sequences (1-2 s/projection, 60 projections, every 6°) were obtained for the first 8 min, followed by slower acquisitions (3-4 s/projection) during the rest of the study. Renal activity was measured in the total kidney volume by regions of interest drawn on consecutive transaxial slices of the third SPECT, which were then copied on the whole 12-SPECT series. Corresponding time-activity curves were created. DSPECT(AC) parameters were compared with those of planar renogram. The reference method for split renal function was 99mTc-DMSA (geometrical mean of anterior and posterior projection counts) and for GFR the Cr-51 EDTA 2-blood sample clearance method. DSPECT(AC) images were of good quality. There was good correlation between renogram parameters (time to peak activity and NORA20) comparing the two techniques (r = 0.959 and 0.933, respectively). In 21 cases with >30% absolute difference between the two kidneys, spilt renal function calculation by DSPECT(AC) correlated perfectly (r = 0.968) with the reference method, whereas planar renogram was less accurate (r = 0.843). Anatomic information provided by nonenhanced CT offered an integrated structural-functional view valuable for final diagnosis. DSPECT(AC) early kidney uptake as a fraction of injected dose correlated better with reference GFR (r = 0.789) than the Gates' method (r = 0.642). 99mTc-DTPA dynamic SPECT/CT renogram is feasible with conventional SPECT/CT systems. It allows accurate split renal function measurement, offers additional anatomical information and can be used for closer approximation of GFR compared with Gates' method.

Neurotransmitter system gene variants as biomarkers for the therapeutic efficacy of rTMS and SSRIs in obsessive-compulsive disorder.

This study aims to examine the potential influence of RS4680 (COMT), RS16965628 (SLC6A4), and RS1019385 (GRIN2B) polymorphisms on the therapeutic response to repetitive transcranial magnetic stimulation (rTMS) and selective serotonin reuptake inhibitors (SSRIs) in individuals with obsessive-compulsive disorder (OCD). Thirty-six untreated outpatients diagnosed with OCD were recruited and allocated to active or sham rTMS groups for two weeks. The mean age of the participants was 31.61, with 17 males (47.22%) and 19 females (52.78%). Peripheral blood samples (5 mL) were collected from each participant using ethylenediaminetetraacetic acid (EDTA) vacuum tubes for genotyping purposes, clinical evaluation was taken place at baseline and second week. The A allele of RS4680, C allele of RS16965628, and GG allele of RS1019385 were identified as potential bio-markers for predicting treatment response to OCD treatments (rTMS & SSRIs). Those genes may serve as bio-markers for the combined treatment of rTMS and SSRIs in OCD. The finding hold promise for further research and the potential implementation of precision treatment of OCD. https://www.chictr.org.cn, identifier ChiCTR1900023641.

Dystrophic calcinosis: structural and morphological composition, and evaluation of ethylenediaminetetraacetic acid (‘EDTA’) for potential local treatment

BackgroundTo perform a detailed morphological analysis of the inorganic portion of two different clinical presentations of calcium-based deposits retrieved from subjects with SSc and identify a chemical dissolution of these deposits suitable for clinical use.MethodsChemical analysis using Fourier Transform IR spectroscopy (‘FTIR’), Raman microscopy, Powder X-Ray Diffraction (‘PXRD’), and Transmission Electron Microscopy (‘TEM’) was undertaken of two distinct types of calcinosis deposits: paste and stone. Calcinosis sample titration with ethylenediaminetetraacetic acid (‘EDTA’) assessed the concentration at which the EDTA dissolved the calcinosis deposits in vitro.ResultsFTIR spectra of the samples displayed peaks characteristic of hydroxyapatite, where signals attributable to the phosphate and carbonate ions were all identified. Polymorph characterization using Raman spectra were identical to a hydroxyapatite reference while the PXRD and electron diffraction patterns conclusively identified the mineral present as hydroxyapatite. TEM analysis showed differences of morphology between the samples. Rounded particles from stone samples were up to a few micron in size, while needle-like crystals from paste samples reached up to 0.5 µm in length.Calcium phosphate deposits were effectively dissolved with 3% aqueous solutions of EDTA, in vitro. Complete dissolution of both types of deposit was achieved in approximately 30 min using a molar ratio of EDTA/HAp of ≈ 300.ConclusionsStone and paste calcium-based deposits both comprise hydroxyapatite, but the constituent crystals vary in size and morphology. Hydroxyapatite is the only crystalline polymorph present in the SSc-related calcinosis deposits. Hydroxyapatite can be dissolved in vitro using a dosage of EDTA considered safe for clinical application. Further research is required to establish the optimal medium to develop the medical product, determine the protocol for clinical application, and to assess the effectiveness of EDTA for local treatment of dystrophic calcinosis.