Electrospun Nanofibers Research Articles

Contribution of piezoelectric effect on piezo-phototronic coupling in ferroelectrics: A theory assisted experimental approach on NBT.

A new study explores the distinct roles of spontaneous polarization and piezoelectric polarization in piezo-phototronic coupling. This investigation focuses on differences in photocatalytic and piezo-photocatalytic performance using sodium bismuth titanate, a key ferroelectric material. The research aims to identify which type of polarization has a greater influence on piezo-phototronic effects. A theoretical assessment complements the experimental findings, providing additional insights. This study explores the enhanced piezo-phototronic performance of electrospun nanofibers compared to sol-gel particles under different illumination conditions (11 W UV, 250W UV, and natural sunlight). Electrospun nanofibers exhibited a rate constant (k) improvement of 2.5 to 3.75 times, whereas sol-gel particles showed only 1.3 to 1.4 times higher performance when ultrasonication was added to photocatalysis. Analysis using first-principle methods revealed that nanofibers had an elastic modulus (C33) about 2.15 times lower than sol-gel particles, indicating greater flexibility. The elongation of the lattice along the z axis in the case of nanofibers reduced the covalency in the Bi-O and Ti-O bonds. These structural differences reduced spontaneous polarization and piezoelectric stress coefficients (e31 and e33). Despite having lower piezoelectric stress coefficients, higher flexibility in nanofibers led to a higher piezoelectric strain coefficient, 2.66 and 1.97 times greater than sol-gel particles, respectively. This improved the piezo-phototronic coupling for nanofibers.

High-Strength and Conductive Electrospun Nanofiber Yarns

In electrospinning, nanofibers are frequently produced in nonwoven web form. Their poor mechanical properties (below 100 MPa) and difficulty in tailoring the fibrous structure have restricted their applications. However, advanced materials must be highly resistant to both deformation and fracture. By combining electrospinning technology with stretching, we have overcome this disadvantage and demonstrated a polyacrylonitrile nanofiber yarn with a tensile strength of 743 ± 20 MPa. The nearly perfect uniaxial orientation of the fibrils under the stretching process is crucial for the remarkable mechanical properties of the yarn. Additionally, the nanofiber yarn was functionalized by a dip-coating process with silver nanowires (AgNWs), imparting conductive properties. This conductive, high-strength nanofiber yarn demonstrates practical applications in flexible and wearable devices. The presented strategy is versatile and can be adapted to create other high-performance nanofiber yarns, with potential uses in fields such as biomedicine and smart textiles.

Development and characterization of solriamfetol-loaded PVA/PLGA electrospun nanofiber membranes: A promising approach for sustained narcolepsy treatment

Narcolepsy presents challenges in medication adherence and delivery, with traditional oral medications not always suitable for patients experiencing unexpected sleep episodes or difficulty in swallowing pills. This study focused on developing a solriamfetol (SF) loaded nanofiber membrane using a polymer blend of polyvinyl alcohol (PVA) and polylactic-co-glycolic acid (PLGA) for the management of narcoleptic patients with non-oral dosage options. The design required synthesis, optimization, characterization, and evaluation of these nanofibers for transdermal drug delivery. Using a Box-Behnken design, the nanofibers were produced via the electrospinning technique, achieving a high drug content of 96.31 ± 1.21 % and entrapment efficiency of 96.18 ± 1.42 %. The in vitro drug release studies demonstrated a prolonged release profile of SF over 24 h, with 97 % ± 2 % of the drug released. The SEM analysis revealed that the surface morphology of the nanofibers was smooth and homogenous, and the average diameter of the SF/PVA/PLGA nanofibers was found to be 150.23 ± 2.50 nm. X-ray diffraction results confirmed the amorphous structure of the nanofibers. The zebrafish embryonic toxicological study did not reveal any signs of toxicity or morphological abnormalities in the developing embryos, indicating that the nanofibers are safe. The results point to the applicability of SF nanofiber membranes in personalized narcolepsy therapy, which improves patients’ quality of life and the efficacy of their treatment. These nanofibers can be given in the form of a transdermal patch to patients for sustained drug delivery, even when they fall asleep or when they cannot take medicines orally.

High Methylene Blue Adsorption Efficiency of Cellulose Acetate-Based Electrospun Nanofiber Membranes Modified with Graphene Oxide and Zeolite

High Methylene Blue Adsorption Efficiency of Cellulose Acetate-Based Electrospun Nanofiber Membranes Modified with Graphene Oxide and Zeolite

Electrospun nanofibers membranes of La(OH)3/PAN as a versatile adsorbent for fluoride remediation: Performance and mechanisms

Abstract Excessive existence of fluoride in water resources can lead to harmful impacts on ecosystems and organisms. Electrospun polyacrylonitrile (PAN) nanofiber membranes loaded with La(OH)3 nanorods composites (La(OH)3/PAN electrospun nanofiber membranes [ENFMs]) are fabricated and used as an efficient fluoride scavenger. Adsorbent fabricate protocols, pH, initial F− concentration, adsorbent dosage, and adsorption time, in addition to coexisting anions, were systematically evaluated. The investigation unveils that a pH of 3.0 is optimal for F− remediation. The adsorption kinetics and isotherm of La(OH)3/PAN ENFMs are well described by the pseudo-second-order model (R 2 > 0.997) with characteristics of chemisorption and Langmuir isotherm (R 2 > 0.999) with the feature of single-layer coverage. The existence of Cl−, SO4 2−, NO3 −, and CO3 2− does not significantly hinder fluoride removal by La(OH)3/PAN ENFMs with the exception of PO4 3−. Calculations of ΔH, ΔG, and ΔS reveal that the nature of F− adsorption onto La(OH)3/PAN ENFMs is endothermic and favorable at a higher temperature.

Combustion and thermodynamics properties of erythritol tetranitrate-based energetic films composed by electrospinning nano fibers

ABSTRACT High energy composite films made from high explosives has important applications in pyrotechnics. In this study, electrostatic spraying was used to prepare energy-containing films based on 1,2,3,4-butanetetrol tetranitrate (ETN). The results show that all energy containing films are made of nanofibres. They have excellent hydrophobicity and combustion properties. In particular, monolayer films in which ETN is the main energy containing substance. Once ignited, the trace monolayer film generates a maximum pressure of 0.85 MPa and an adiabatic flame temperature of 2,855 °C. For single and double layer films, the heat of combustion can reach 9899 J/g and 11975 J/g respectively. The level of combustion heat can also be controlled by adjustment of the ETN content. The results of the thermo-properties performance evaluation show that by optimizing the nanostructure, the ETN-based energy-containing fiber membranes can meet the requirements of advanced pyrotechnic products. In particular, there is great potential in the metastable intermixed composites (MICs) field.

Design of cellulose nanocrystal‐integrated poly(vinyl alcohol)/polyethylene glycol electrospun nanofiber scaffolds for biomedical applications

AbstractThe present study aims to fabricate cellulose nanocrystals (CNCs) doped poly(vinyl alcohol) polyethylene glycol (PVA/PEG) nanocomposite films for biomedical applications. The nanocomposite films were prepared by using electrospinning techniques with varying percentages of CNCs (10% and 20%) mixed with PVA and PEG (50:50). The properties of the produced nanocomposites were evaluated using a battery of tests. The results of surface morphology and structural miscibility obtained from field emission‐scanning electron microscopy (FE‐SEM), atomic force microscopy, and Fourier transformer infra‐red studies revealed appreciable compatibility among the three components (CNCs, PVA, and PEG). FE‐SEM micrographs revealed that the nanomaterials underwent a dramatic transition from discontinuous to continuous fibers, with interconnected or network‐like fibers. The constructed scaffold material's stability went up from three to four phases, according to thermal and degradation experiments. In addition, research on biodegradation and water absorption found that CNCs outperformed pure PVA and PVA/PEG in terms of swelling percentage time and enzyme degradation rate. The hemolysis assay of the PVA/PEG/CNC scaffold showed good compatibility (below 5%) and according to the MTT assay, both NIH 3T3 and L929 cells survived well, indicating that the CNCs could serve as a useful scaffold for tissue engineering applications such skin tissue regeneration. In sum, the findings proved that biological domains including tissue engineering and wound healing can benefit from produced nanofiber scaffolds.

Transparent and Mechanically Robust Janus Nanofiber Membranes for Open Wound Healing and Monitoring.

The electrospun nanofiber membrane has demonstrated great potential for wound management due to its porous structure, large surface area, mechanical strength, and barrier properties. However, there is a need to develop transparent bioactive nanofibers with strong mechanical properties to facilitate the monitoring of the healing process. In this study, we present an electrospinning-based method for creating transparent (∼80-90%), strong (∼11-13 MPa), and Janus nanofiber membranes. The innovative square pattern architecture of the membrane includes a thin hydrophobic polycaprolactone layer on top of a layer of hydrophilic ethylene-vinyl alcohol nanofiber, which enables the absorption of excess biofluid from the wound and exhibits Janus wettability for water. Furthermore, incorporating 5% chitosan into the composition of the nanofibers accelerates the healing process through its antioxidant properties and antimicrobial activity against various bacteria, including drug-resistant strains. The developed membrane also demonstrates skin-repairing function, quick blood clotting (around 145 ± 12 s), and biocompatibility with keratinocyte (≥90%), as well as in vitro quick cell migration (∼24 h). With a tensile strength of 11-13 MPa, the membrane effectively adheres to the knee joint even after running 4 km. These optimal properties of the electrospun nanofiber membrane make it suitable for effective wound management and inspection of the healing process, without the need for frequent dressing changes.

Research Progress of Flexible Electronic Devices Based on Electrospun Nanofibers.

Electrospun nanofibers have become an important component in fabricating flexible electronic devices because of their permeability, flexibility, stretchability, and conformability to three-dimensional curved surfaces. This review delves into the advancements in adaptable and flexible electronic devices using electrospun nanofibers as the substrates and explores their diverse and innovative applications. The primary development of key substrates for flexible devices is summarized. After briefly discussing the principle of electrospinning, process parameters that affect electrospinning, and two major electrospinning techniques (i.e., single-fluid electrospinning and multifluid electrospinning), the review shines a spotlight on the recent breakthroughs in multifunctional and stretchable electronic devices that are based on electrospun substrates. These advancements include flexible sensors, flexible energy harvesting and storage devices, flexible accessories for electronic devices, and flexible environmental monitoring devices. In particular, the review outlines the challenges and potential solutions of developing electrospun nanofibers for flexible electronic devices, including overcoming the incompatibility of multiple interfaces, developing 3D microstructure sensor arrays with gradient geometry for various imperceptible on-skin devices, etc. This review may provide a comprehensive understanding of the rational design of application-oriented flexible electronic devices based on electrospun nanofibers.

Antibacterial and wound healing stimulant nanofibrous dressing consisting of soluplus and soy protein isolate loaded with mupirocin

Severe cutaneous injuries may not heal spontaneously and may necessitate the use of supplementary therapeutic methods. Electrospun nanofibers possess high porosity and specific surface area, which provide the necessary microenvironment for wound healing. Here in, the nanofibers of Soluplus-soy protein isolate (Sol-SPI) containing mupirocin (Mp) were fabricated via electrospinning for wound treatment. The fabricated nanofibers exhibited water absorption capacities of about 300.83 ± 29.72% and water vapor permeability values of about 821.8 ± 49.12 g/m2 day. The Sol/SPI/Mp nanofibers showed an in vitro degradability of 33.73 ± 3.55% after 5 days. The ultimate tensile strength, elastic modulus, and elongation of the Sol/SPI/Mp nanofibers were measured as 3.61 ± 0.29 MPa, 39.15 ± 5.08 MPa, and 59.11 ± 1.94%, respectively. Additionally, 85.90 ± 6.02% of Mp loaded in the nanofibers was released in 5 days in vitro, and by applying the Mp-loaded nanofibers, 93.06 ± 5.40% and 90.40 ± 5.66% of S. aureus and E. coli bacteria were killed, respectively. Human keratinocyte cells (HaCat) demonstrated notable biocompatibility with the prepared nanofibers. Furthermore, compare to other groups, Sol-SPI-Mp nanofibers caused the fastest re-epithelialization and wound healing in a rat model. The findings of this study present a novel nanofiber-based wound dressing that accelerates the healing of severe skin wounds with the risk of infection.

Facile fabrication of foldable electrospun nanofiber electrodes for electrodes for electronic biosensing

This study presents a rapid, sensitive and selective sensor based on electrospun nanofibers on laser-patterned electrodes, in which the laser micromachining process can directly fabricate the graphene electrode device for the electronical detection of glucose molecule. The layer of graphene film was formed on the glass substrate by a screen printing technique, and then the graphene electrodes can be fabricated by the ultraviolet (UV) nanosecond laser process with the wavelength of 355 nm. Based on the controlled the laser fluence and pulses, the electrode gap of 60 μm within the device can be fabricated. The polyvinyl alcohol (PVA) and glucose oxidase (GOD) composite nanofiber with weight percentage of 8% can be used by the electrospun process with used Glutaraldehyde(GA) steam for cross linking process. After that, it is blended with the conductivity of poly(3,4-ethylenedioxythiophene): poly (styrene sulfonate) (PEDOT:PSS), and the foldable nanofiber structures was made by electrospun process on the graphene electrode device. Finally, the electrical detection of graphene electrode device with the nanofibers at different concentrations of glucose can be measured, resulting in the linear variation is detecting the glucose concentration ranging form 0.01 to 3.12 mM. This work indicated that the low concentration and highly sensitive can be used for electronic biosensors

Fabrication and characterization of novel electrospun nanofibers based on grass pea (Lathyrus sativus L.) protein isolate loaded with sumac (Rhus coriaria L.) extract

In this study, sumac extract was utilized as an active ingredient and combined with grass pea protein isolate and polyvinyl alcohol to produce novel active nanofiber mats using an electrospinning technique. First, nanofiber mats were fabricated by different ratios (100:0, 90:10, 70:30, 50:50, 30:70, 10:90, 0:100) of grass pea protein isolate and polyvinyl alcohol. The characterization of nanofiber mats revealed that the nanofibers with a polymer ratio of 50:50 had appropriate mechanical properties and presented a fibrous and uniform morphology. Therefore, the 50:50 polymer solution ratio was selected to produce active nanofibers by adding different amounts (0%, 2%, and 4% (w/v)) of sumac extract. The average diameters of nanofibers decreased from 150 ± 31 to 122 ± 25, and 105 ± 19 nm, by increasing the concentration of sumac extract. Based on the SEM results, the electrospun nanofibers exhibited a bead-free and smooth surface. The FTIR and XRD analyses indicated the presence of intermolecular hydrogen bonds between the components. The antioxidant activity of the nanofibers was confirmed by DPPH analysis and ranged between 3.33% and 68.75%. Additionally, the antimicrobial test results indicated that the nanofibers with the highest sumac concentration (4%) displayed inhibitory activity against Staphylococcus aureus, resulting in an inhibition zone of 10 mm. The optimal treatment of this study was grass pea protein isolate: polyvinyl alcohol ratio of 50:50 containing 4% sumac extract which can be used as a natural antimicrobial and antioxidant agent.

A closed-loop sustainable method for the fabrication of electrospun nanofiber using food waste for filtration of particulate matters (PMs) and volatile organic matter (VOCs) from air

Indoor air pollution significantly impacts human health and the environment. Humans suffer the greatest health burden due to inefficient combustion technologies and polluted fuels. Therefore, air filtration is essential for a healthy and prosperous household. This study aims to develop a sustainable approach for the fabrication of biodegradable electrospun nanofibers (ENs) as air filters from food waste materials and offer a closed-loop circular solution and potential replacement for non-biodegradable HEPA air filters. We have tested banana peel extract (BPE), eggshell membrane, chitosan, and starch blended with polyvinyl alcohol (PVA) for fabricating ENs. Among the nanofibers investigated for air filtration application, BPE/PVA nanofiber shows the best performance in terms of maximum particulate matter (PM) removal efficiency and minimum pressure drop while incorporating > 50 % of the food waste into the electrospinning solution. Adding BPE into a 10 % PVA solution leads to a reduction in the hydrophilic behavior of the BPE/PVA nanofiber as compared to neat 10 % PVA ENs. The BPE/PVA nanofiber shows minimum pressure drop (156–160 Pa) and highest quality factor (Qf) in comparison with other waste-derived nanofibers with > 98 % filtration efficiency of PM2.5. Further, BPE/PVA nanofiber shows the highest adsorption of xylene vapor among other food waste derived nanofibers studied. Based on the above results, it can be concluded that BPE based nanofiber shows the best performance as air filter media among all other food waste-based ENs. The study demonstrates a successful regeneration and reuse of the BPE/PVA filter up to 3 cycles. The leftover material from banana peels after BPE extraction was utilized as a soil ameliorant. It showed 55 % soil water retention (SWR) capacity, making it possible to apply in arid regions or crops with high water requirements.

Fabrication of composite RGD-tagged poly(lactic acid)-graphene oxide nanofiber containing bone-forming peptide-3 loaded-dendritic silica nanoparticles for bone regeneration in rabbit

In the current study, polylactic acid (PLA)/graphene oxide (GO) based composite scaffolds were fabricated by electrospinning method and then covalently modified with bone-forming peptide-3 (BFP-3)-loaded thiol-functionalized dendritic mesoporous silica nanoparticles (BFP-3@HS-DMSNs) and RGD. In this regard, PLA electrospinning nanofibers and composite of PLA/GO electrospinning nanofibers containing 0.02, 0.01, 0.04, 0.1, 0.2 % of GO were prepared and characterized in terms of mechanical strength, nanofibers diameter, thermal stability, crystallinity, specific surface area, total pore volume and cell adhesion properties. Among the prepared composites, PLA nanofibers containing 0.02 % GO demonstrated superior mechanical and morphological characteristics along with better cell adhesion for mesenchymal stem cell. Then, the PLA/0.02 %GO nanofiber was treated with plasma and consequently modified with N-(2-aminoethyl)maleimide linker which was applied for Cys-RGD and BFP-3@HS-DMSNs conjugation. The obtained results showed desirable adhesion of PLA/0.02 %GO nanofiber after incorporation of RGD (5 % of maleimide groups of the linker) and DMSNs which significantly increase cell adhesion potency (1.53 folds). By incorporation of BFP-3@HS-DMSNs (equivalent to 0.1 µg of BFP-3) to the RGD-tagged PLA/0.02 %GO nanofiber, the scaffold demonstrated better cytocompatibility and MSC differentiation to osteoblast based on biomineralization assay via alizarin red (4.2 folds) and alkaline phosphatase activity (1.7 folds) tests. In preclinical stage, after skull defect creation in rabbits, 5 treatments groups comprising PLA/0.02 %GO nanofiber, PLA/0.02 %GO/DMSNs, PLA/0.02 %GO/DMSNs/Cys-RGD, PLA/0.02 %GO/BFP-3@DMSNs and PLA/0.02%GO/BFP-3@DMSNs/Cys-RGD were used for bone regeneration in skull defects. After 3 months, the implantation of PLA/0.02GO/BFP-3@DMSNs/Cys-RGD showed higher bone regeneration based on CBCT imaging (18.875 mm2 bone formed area) in comparison with other treatment groups. This hybrid multimodal platform is purposely organized interactive processes which lead to potential bone regeneration.

Development and characterization of antibacterial marine extract-infused cellulose acetate nanofibers as wound dressings for combatting multidrug-resistant wound infections

Wound infections caused by multidrug-resistant bacteria pose a significant challenge globally in healthcare. Traditional wound dressings often lack efficacy against these resilient pathogens, necessitating the exploration of innovative approaches to combat infections and promote wound healing. This study was designed to investigate a novel wound dressing marine extract-infused electrospun cellulose acetate nanofibers (CANF) with particular emphasis on combating multidrug-resistant bacteria. Cellulose acetate solutions were combined with marine extract (Heteroxenia Fuscescens soft coral, H. Fu) before the creation of electrospun nanofibers. The antibacterial activities of H. Fu extract and the prepared nanofiber mats were explored against Pseudomonas aeruginosa, Acinetobacter baumannii, Staphylococcus aureus, and Staphylococcus epidermidis. Furthermore, the antibacterial properties of the crude H. Fu extract were directly assessed, showing potent activity against several pathogens. Results displayed that H. Fu extract has a robust antibacterial action against tested bacteria. Different concentrations of H. Fu (0.05 g, 0.1 g, 0.2 g, and 0.3 g) were added to CA solution, and named as H. Fu-1@CANF, H. Fu-2@CANF, H. Fu-3@CANF and H. Fu-4@CANF, respectively. The obtained results from SEM analysis demonstrated the smooth and uniform fibers. As observed, the addition of H. Fu with specific concentrations (0.05 g, 0.1 g, 0.2 g) has no significant impact on the smooth properties of the formed nanofibers. Increasing the concentration of H. Fu (0.3 g) leads to the formation of nanofibers coated with huge beads. FTIR affirmed the existence of H. Fu that blended with CANF. The hydrophilicity of the formed CANF was significantly enhanced thanks to the presence of H. Fu extract. The contact angle values of CANF, H. Fu-1@CANF, H. Fu-2@CANF, and H. Fu-3@CANF were 33.3°, 57.1°, 60.8° and 62.9°, respectively. The mechanical properties in terms of ultimate force (kg) recoded values were 0.89, 0.95, 1.2, 1.3 for CANF, H. Fu-1@CANF, H. Fu-2@CANF and H. Fu-3@CANF, respectively, those of CNF were markedly enhanced when loaded with H. Fu. This study evaluates the antibacterial efficacy of nanofiber mats loaded with H. Fu extract against common cutaneous bacterial pathogens. Four nanofiber samples were tested for their inhibitory impact on bacterial survival counts using the disc diffusion method. Important results from the study include the observation that H. Fu-3@CANF exhibited the largest zones of inhibition (ZOI) with diameters of 35 ± 0.25 mm for P. aeruginosa, 32 ± 0.65 mm for A. baumannii, 28 ± 0.14 mm for S. aureus, and 27.6 ± 0.48 mm for S. epidermidis. Additionally, the H. Fu-2@CANF sample demonstrated strong antibacterial activity, with ZOI diameters of 32 ± 0.56 mm, 29 ± 0.81 mm, 26 ± 0.27 mm, and 25.4 ± 0.28 mm for the respective bacteria. The Microtox® assay further evaluated the toxicity levels of the nanofiber mats, revealing that while all samples exhibited some toxicity, the H. Fu-3@CANF sample had the lowest toxicity profile. These findings highlight the potential of H. Fu-loaded nanofibers, particularly H. Fu-3@CANF, for broad-spectrum antibacterial applications. The study underscores the importance of incorporating bioactive compounds into nanofiber mats to enhance their antimicrobial properties, making them suitable candidates for medical and environmental applications requiring effective bacterial eradication.

Metal-organic framework electrospun nanofibers in application to dye removal from textile wastewaters: A Review

Metal-organic framework electrospun nanofibers in application to dye removal from textile wastewaters: A Review

Adsorption Capacity Prediction and Optimization of Electrospun Nanofiber Membranes for Estrogenic Hormone Removal Using Machine Learning Algorithms

Adsorption Capacity Prediction and Optimization of Electrospun Nanofiber Membranes for Estrogenic Hormone Removal Using Machine Learning Algorithms

Hybrid electrospinning of pullulan and citrus pectin to load astaxanthin: Preparation, characterization, and functional evaluation

Pullulan (PUL) is a widely used agent for electrospinning. However, nanofibers electrospun solely from PUL exhibit a highly hydrophilic nature and a bead-like structure. In this study, 1–5 wt% citrus pectin (CP) was introduced to construct a hybrid electrospinning system to investigate the effects of CP concentration on the properties of the electrospun nanofibers. The results reveal that the bead-like structure, rigidity, and hydrophobicity of the nanofibers underwent significant improvements following the introduction of CP. Furthermore, to demonstrate the protective effect of the nanofiber on astaxanthin, 0.1 wt% astaxanthin was encapsulated in the hybrid electrospinning system containing 5 wt% CP. The results show that after encapsulating astaxanthin, the rigidity of the nanofiber further increased, with a tensile strength of 12.5 MPa and a break elongation of 2.9 %. Additionally, the nanofiber system demonstrates excellent protection of the antioxidant activity of astaxanthin under UV exposure compared to free astaxanthin.

Spectrally selective and thermally insulating hybrid nanofiber aerogel coolers for building energy conservation

With the advancement of worldwide carbon neutralization, passive radiative cooling (PRC) has attracted tremendous interest in energy conservation by dissipating heat into the ultracold outer space without any electricity consumption. Despite some progress has been made in tailoring spectral properties for PRC, it still remains a crucial challenge in fabricating efficient and low-cost coolers for building energy saving. Herein, hierarchical cellulose-based aerogel coolers consisting of beads-on-string structural electrospun nanofibers are manufactured for all-day and all-region energy saving by combining radiative cooling and thermal insulation in one design. The hierarchically porous architectures and well-designed chemical compositions endow the aerogels with strong solar reflectance (∼0.974), high mid-infrared emittance (∼0.985), and ultra-low thermal conductivity (0.0285 W (m K)−1), achieving a sub-ambient cooling of ∼8.24 °C during the daytime and ∼7.41 °C during the nighttime. The aerogels also exhibit exceptional compressive resiliency, anti-aging, and self-cleaning properties, promising for durable cooling under harsh conditions. The building energy simulations show that about 23.1 kWh m−2 of the total energy consumption per year can be saved if the aerogel coolers are widely deployed as building envelopes in China. This work provides new perspectives for the development of advanced aerogel coolers for future energy saving applications.

Electrospun nanofibrous scaffolds reinforced with therapeutic lithium/manganese-doped calcium phosphates: Advancing skin cancer therapy through apoptosis induction

In the current study we fabricated potent materials by incorporating therapeutic elements into calcium phosphates (CPs) to combat cancer. This involved synthesizing manganese (Mn)- and lithium (Li)-doped CPs and loading them into electrospun nanofibers (NFs) composed of chitosan (CS) and polyethylene oxide (PEO). The characterized CPs exhibited excellent properties, including a particle size of 47–75 nm, surface charge of –(30−56) mV, and specific surface area of 75–266 m2/g. The electrochemical analysis revealed that Mn and Mn/Li-doped CPs are promising for generating oxygen free radicals and H2O2, crucial for cancer therapy. Biological evaluation showcased the outstanding performance of the developed materials. MTT assay revealed a cytotoxic effect of nano-constructs on melanoma A375 cell line without adverse effects on normal L929 cells over 72 h. Annexin V/PI apoptosis assay indicated substantial apoptosis rates in A375 cells treated with PC-20 % (62.55 ± 4.59 %). The obtained data of qPCR analysis of pro-apoptotic and anti-apoptotic genes (P53, Bax, Bcl-2) in A375 cells treated with different CP nanoparticles (NPs) showed a significant increase in P53 and Bax gene expression, indicating high levels of A375 cell apoptosis. Additionally, the samples containing Mn ion exhibited high reactive oxygen species (ROS) generation. In conclusion, the fabricated NFs scaffolds hold promising potential for cancer therapy.