Electronic Ballast For High Intensity Discharge Lamps Research Articles

A Generalized Dynamic Conductance Model for High Intensity Discharge Lamps and its Prospective Application to Design Dimmable Electronic Ballast

A generalized model for high intensity discharge (HID) lamp is developed based on the Francis-Damelincourt dynamic conductance model of electric discharge by replacing the model constants A, B, C, D with four experimentally determined coefficient functions of rated lamp power and root mean square supply voltage. Experimental validation of this model is done, which shows a maximum deviation of about 5 %. Moreover, sensitivity analysis for the model coefficients is also performed, results of which conform to the physical behaviour of high pressure sodium (HPS) and metal halide (MH) lamps. This model is capable to simulate electrical characteristics of HPS and MH lamps of wide range of commercially available rated power (70–400) W fed by a wide range of supply voltage (180–250) V, 50 Hz. As a prospective application, the model is applied to design dimmable low frequency square wave electronic ballast for HID lamps. A design algorithm is proposed for this purpose. Performance analysis of the designed ballast is conducted in Matlab-Simulink environment, which shows fairly good performance of the circuit in terms of dimming accuracy (maximum deviation 2.64 %), lamp power factor (≥ 0.993), and lamp current crest factor (equal to 1.0). The model can also be utilized for designing electronic ballasts of other topologies.

Design and Implementation of a Single-Stage Acoustic-Resonance-Free HID Lamp Ballast With PFC

High-intensity-discharge (HID) lamps are widely utilized in a variety of lighting circumstances that need high luminance. This paper proposes a single-stage electronic ballast for HID lamps; the ballast offers power factor correction and is acoustic resonance free. The presented HID lamp ballast integrates a discontinuous-conduction-mode (DCM)-operated bridgeless power factor correction (PFC) converter for shaping the input utility-line current with a high-frequency (36 kHz)/low-frequency (60 Hz) square-wave-driven half-bridge inverter for supplying low-frequency (60 Hz) square-wave sources to the HID lamp. The features of the proposed ballast are high power factor, low total harmonic distortion (THD) of the input current, cost effectiveness, and that it avoids acoustic resonance. The operational modes, key design guidelines, and a design example are included. A 70 W prototype HID lamp ballast circuit operating with 110 V-rms input utility-line voltage has been implemented and testified. The functionalities of the presented ballast are demonstrated by satisfactorily experimental results with a maximum efficiency of 90.8%, a maximum power factor of 0.998, and a minimum current THD of 11.13%.

A high-frequency electronic ballast for HID lamps based on a /spl lambda//4-long distributed constant line

A novel type of solid-state ballast, which operates in the megahertz-range frequency, is presented in this paper. A circuit composed of a voltage-source half-bridge inverter, a distributed constant line and a parallel LC resonant circuit has been developed for this purpose. The high-intensity discharge (HID) lamp is connected to the output terminal of the inverter through the distributed constant line. Here, since the length of the line is adjusted to 1/4 of the propagation wavelength /spl lambda/ (/spl lambda//4 condition), the output voltage of the voltage-source inverter can be converted to a current source on the load side. Therefore, the ballast can supply not only high voltage to the HID lamp for initiating discharge, but also stable current to it during discharge condition. The modification of the proposed circuit is also proposed in order to expand the operating frequency without increasing the undesirable harmonic current. The experimental results from a prototype system verify the theoretical procedure.

High-frequency Electronic Ballast for HID Lamps Using λ/4-long Distributed Constant Line

A novel solid state ballast, which operates in the MHz-range frequency, is presented in this paper. A circuit composed of a voltage-source half-bridge inverter, a distributed constant line, and a parallel LC resonant circuit has been developed for this purpose. The HID (High Intensity Discharge) lamp is connected to the output terminal of the inverter through the distributed constant line. Here, since the length of the line is adjusted to 1/4 of the propagation wavelength λ(λ/4 condition), the output voltage of the voltage-source inverter can be converted to a current source on the load side. Therefore, the ballast can supply not only high voltage to the HID lamp for initiating discharge but also stable current to it during discharge condition. The modification of the proposed circuit is also presented in order to expand the operating frequency without increasing the undesirable harmonic current. The experimental results from a prototype system verify the theoretical procedure.