Electron Acceptors For Organic Solar Cells Research Articles

Benzotriazacycle Cored Perylene Diimide Non-fullerene Acceptors for High-performance Organic Solar Cells

Background: Perylene diimide (PDI) is among the most investigated non-fullerene electron acceptor for organic solar cells (OSCs). Constructing PDI derivatives into three-dimensional propellerlike molecular structures is not only one of the viable routes to suppress the over aggregation tendency of the PDI chromophores but also rise possibilities to tune and optimize the optoelectronic property of the molecules. Objective: In this work, we reported the design, synthesis, and characterization of three electronaccepting materials, namely BOZ-PDI, BTZ-PDI, and BIZ-PDI, each with three PDI arms linked to benzotrioxazole, benzotrithiazole, and benzotriimidazole based center cores, respectively. Method: The introduction of electron-withdrawing center cores with heteroatoms does not significantly complicate the synthesis of the acceptor molecules, but drastically influences the energy levels of the propeller-like PDI derivatives. Result: The highest power conversion efficiency was obtained with benzoxazole-based BOZ-PDI reaching 7.70% for its higher photon absorption and charge-transport ability. Conclusion: This work explores the utilization of electron-withdrawing cores with heteroatoms in the propeller-like PDI derivatives, which provides a handy tool to construct high-performance nonfullerene acceptor materials.

Benzothiadiazole-based Conjugated Polymers for Organic Solar Cells

Benzothiadiazole (BT) is an electron-deficient unit with fused aromatic core, which can be used to construct conjugated polymers for application in organic solar cells (OSCs). In the past twenty years, huge numbers of conjugated polymers based on BT unit have been developed, focusing on the backbone engineering (such as by using different copolymerized building blocks), side chain engineering (such as by using linear or branch side units), using heteroatoms (such as F, O and S atoms, and CN group), etc. These modifications enable BT-polymers to exhibit distinct absorption spectra (with onset varied from 600 nm to 1000 nm), different frontier energy levels and crystallinities. As a consequence, BT-polymers have gained much attention in recent years, and can be simultaneously used as electron donor and electron acceptor in OSCs, providing the power conversion efficiencies (PCEs) over 18% and 14% in non-fullerene and all-polymer OSCs. In this article, we provide an overview of BT-polymers for OSCs, from donor to acceptor, via selecting some typical BT-polymers in different periods. We hope that the summary in this article can invoke the interest to study the BT-polymers toward high performance OSCs, especially with thick active layers that can be potentially used in large-area devices.

A helical perylene diimide-based acceptor for non-fullerene organic solar cells: synthesis, morphology and exciton dynamics.

Helical perylene diimide-based (hPDI) acceptors have been established as one of the most promising candidates for non-fullerene organic solar cells (OSCs). In this work, we report a novel hPDI-based molecule, hPDI2-CN2, as an electron acceptor for OSCs. Combining the hPDI2-CN2 with a low-bandgap polymeric donor (PTB7-Th), the blending film morphology exhibited high sensitivity to various treatments (such as thermal annealing and addition of solvent additives), as evidenced by atomic force microscope studies. The power conversion efficiency (PCE) was improved from 1.42% (as-cast device) to 2.76% after thermal annealing, and a PCE of 3.25% was achieved by further addition of 1,8-diiodooctane (DIO). Femtosecond transient absorption (TA) spectroscopy studies revealed that the improved thin-film morphology was highly beneficial for the charge carrier transport and collection. And a combination of fast exciton diffusion rate and the lowest recombination rate contributed to the best performance of the DIO-treated device. This result further suggests that the molecular conformation needs to be taken into account in the design of perylene diimide-based acceptors for OSCs.

Potential of Nonfullerene Small Molecules with High Photovoltaic Performance

Over the past decades, fullerene derivatives have become the most successful electron acceptors in organic solar cells (OSCs) and have achieved great progress, with power conversion efficiencies (PCEs) of over 11 %. However, fullerenes have some drawbacks, such as weak absorption, limited energy-level tunability, and morphological instability. In addition, fullerene-based OSCs usually suffer from large energy losses of over 0.7 eV, which limits further improvements in the PCE. Recently, nonfullerene small molecules have emerged as promising electron acceptors in OSCs. Their highly tunable absorption spectra and molecular energy levels have enabled fine optimization of the resulting devices, and the highest PCE has surpassed 12 %. Furthermore, several studies have shown that OSCs based on small-molecule acceptors (SMA) have very efficient charge generation and transport efficiency at relatively low energy losses of below 0.6 eV, which suggests great potential for the further improvement of OSCs. In this focus review, we analyze the challenges and potential of SMA-based OSCs and discuss molecular design strategies for highly efficient SMAs.

Oligomer Molecules for Efficient Organic Photovoltaics.

Solar cells, a renewable, clean energy technology that efficiently converts sunlight into electricity, are a promising long-term solution for energy and environmental problems caused by a mass of production and the use of fossil fuels. Solution-processed organic solar cells (OSCs) have attracted much attention in the past few years because of several advantages, including easy fabrication, low cost, lightweight, and flexibility. Now, OSCs exhibit power conversion efficiencies (PCEs) of over 10%. In the early stage of OSCs, vapor-deposited organic dye materials were first used in bilayer heterojunction devices in the 1980s, and then, solution-processed polymers were introduced in bulk heterojunction (BHJ) devices. Relative to polymers, vapor-deposited small molecules offer potential advantages, such as a defined molecular structure, definite molecular weight, easy purification, mass-scale production, and good batch-to-batch reproducibility. However, the limited solubility and high crystallinity of vapor-deposited small molecules are unfavorable for use in solution-processed BHJ OSCs. Conversely, polymers have good solution-processing and film-forming properties and are easily processed into flexible devices, whereas their polydispersity of molecular weights and difficulty in purification results in batch to batch variation, which may hamper performance reproducibility and commercialization. Oligomer molecules (OMs) are monodisperse big molecules with intermediate molecular weights (generally in the thousands), and their sizes are between those of small molecules (generally with molecular weights <1000) and polymers (generally with molecular weights >10000). OMs not only overcome shortcomings of both vapor-deposited small molecules and solution-processed polymers, but also combine their advantages, such as defined molecular structure, definite molecular weight, easy purification, mass-scale production, good batch-to-batch reproducibility, good solution processability, and film-forming properties. Therefore, OMs are a good choice for solution-processed reproducible OSCs toward scalable commercialized applications. Considerable efforts have been dedicated to developing new OM electron donors and electron acceptors for OSCs. So far, the highest PCEs of solution-processed OSCs based on OM donors and acceptors are 9-10% and 6-7%, respectively. OM materials have become promising alternatives to polymer and/or fullerene materials for efficient and stable OSCs. In this Account, we present a brief survey of the recent developments in solution-processable OM electron donors and acceptors and their application in OSCs. Rational design of OMs with star- and linear-shaped structures based on triphenylamine, benzodithiophene, and indacenodithiophene units and their impacts on device performance are discussed. Structure-property relationships are also proposed. Furthermore, the remaining challenges and the key research directions in the near future are also addressed. In the next years, an interdisciplinary approach involving novel OM materials, especially electron acceptor materials, accurate morphology optimization, and advanced device technologies will probably bring high-efficiency and stable OSCs to final commercialization.

Design Concept for High-LUMO-level Fullerene Electron-acceptors for Organic Solar Cells

Abstract This review article describes design concept, synthesis, and features of fullerene derivatives having high lowest unoccupied molecular orbital (LUMO) levels to achieve high open-circuit voltage in organic thin-film photovoltaic devices. Installation of organic electron-donating groups onto fullerene and decrease of the size of the fullerene π-electron-conjugated system raise the LUMO levels, affording high-performance organic solar cells. Addition of the methano group as the smallest carbon addend to fullerene to obtain 56π-electron fullerene derivatives is likely a promising strategy for this purpose.