Electromagnetic Shielding Effectiveness Research Articles

Preparation of Structure-Function Integrated Layered CNT/Mg Composites.

Magnesium (Mg)-matrix composites have excellent damping and electromagnetic shielding properties. However, the mismatch between their strength and toughness limits their wide application. The aim of this work is to overcome the strength-toughness mismatch by constructing micro- and nanostructures while maintaining the good functional properties of Mg-matrix composites. Electrophoretic deposition (EPD) was used to spread carbon nanotubes (CNTs) out evenly on a Mg foil matrix. After spark plasma sintering (SPS), the grain organisation was refined, and the interlayer bonding was strengthened by hot rolling deformation. Finally, the microstructure, mechanical properties, damping properties, and electromagnetic shielding properties of the composites were analysed. Compared with the pure Mg laminates, the tensile strength and elongation of the CNT/Mg laminates were increased by 6.4% and 108.4%, respectively, with the significant improvement in toughness resulting from the increase in energy required for crack propagation due to the laminate structure. When the total rolling deflection reaches 80%, the interlayer bond strength of the material is significantly increased, the grain is further refined, and the strength and elongation of the composite material reaches the optimum, with the tensile strength reaching 241.70 MPa and the elongation reaching 6.90%. The interlayer interface and grain refinement also affected the damping Mg and electromagnetic shielding effect of the composites. This work provides an experimental idea for the preparation of high-performance structure-function integrated Mg-based materials.

In situ reduction of copper nanoparticles in porous carbonized wood for efficiently enhancing electromagnetic interference shielding performance

In this study, porous carbonized wood was used as the substrate, and a multi-layer composite of copper/carbonized wood/copper (Cu/CW/Cu) layer with light weight, flame retardancy, and efficient electromagnetic shielding effectiveness was prepared by electroless copper method. The results showed that the copper particles can be filled in the layered porous structure of the carbonized wood. The metal Cu layer was evenly covered on the surface of the whole carbonized wood, and the average surface roughness was 7.62 µm. The absorption peak at 2340 cm−1 was significantly enhanced, which proved that the increase of the number of electroless Cu on the carbonized wood surface promoted the improvement of Cu autocatalytic ability. After three depositions of Cu, the conductivity of the composite material reached 1154 S/cm, showing good electrical properties. The shielding effectiveness in the X-band from 8.2 to 12.4 GHz was up to 55.97 dB at low density (0.27 g/cm3). Specific shielding effectiveness SSE/t was as high as 581.69 dB cm2 g−1. Through the “absorption–reflection–absorption” path, high absorption and low reflection are achieved, shielding a large number of incident electromagnetic waves.

Dual sinter-aids to fabricate high-entropy transition metal carbide ceramic and their properties

Due to excellent performances and easy adjustability, more and more researchers pay attention to high-entropy ceramics, which can be applied in many fields. In this work, a high-entropy transition metal carbide ceramic, (Hf0.2Ta0.2Zr0.2Nb0.2W0.2)C, was fabricated by pressureless sintering method. To obtain highly dense ceramic, dual sintering aids (Cr3C2 and C), are employed in the sintering process. Owing to suitable microstructure (grain size and defect density), the ceramics exhibit excellent electric conductivity(0.7040 MS/m) and flexural strength (378 ± 11.4 MPa). Meanwhile, the relationship between electromagnetic shielding effectiveness and different aid content in the X-band is also investigated. The P3 ceramic with a thickness of 1 mm can achieve an EMI shielding efficiency of 92 dB in the X-band as a result of the stronger interface polarization and relaxation effects. High-entropy ceramic obtained in this work would give a different way to fabricate shielding material and can promote the use of high-entropy ceramics as effective EMI shielding materials.

Silver-Coated Waste Rubber Micro-Particles with Low Density, High Stability, and Excellent Electromagnetic Shielding Ability: Design, Preparation, and Characterization

Introduction: The electromagnetic radiation caused by the increasing application of electronic devices is associated with environmental hazards and health risks. background: The electromagnetic radiation caused by the increasing application of electronic devices is associated with environmental hazards and health risks. With the rapid development of science and technology, it is urgent to reduce electromagnetic interference by introducing effective electromagnetic shielding materials. Furthermore, novel electromagnetic shielding materials with increasing stability and decreasing density have become the focus of the current researches. Method: With the rapid development of science and technology, it is urgent to reduce electromagnetic interference by introducing effective electromagnetic shielding materials. Furthermore, novel electromagnetic shielding materials with increasing stability and decreasing density have become the focus of the current research. Herein, silver (Ag) coated rubber (AR) micro-particles (MPs) were prepared by coating Ag nanoparticles (NPs) onto waste AR MPs. objective: Fabrication of Silver (Ag) coated rubber (AR) micro-particles (MPs). Result: The AR MPs not only exhibited superior electromagnetic shielding performance with the electromagnetic interference (EMI) shielding effectiveness (SE) value of 6.1 dB at 5.8 GHz, but also possessed excellent long-time stability (240 h) in high-temperature (85 °C) and high humidity (85% RH) environment. Due to the low density (0.66 g/cm3) of AR-3 MPs, its practical application in lightweight and highly integrated electronic devices is guaranteed. Conclusion: The developed AR MPs have exhibited broad application prospects in the electromagnetic interference (EMI) shielding field due to the good EMI shielding performance, high stability and low density.

Structural, morphological, and EMI shielding evaluations of Sm-Mn co-doped Sr-based M-type hexaferrite for Ku band applications

High-performance, thin, and lightweight EMI (Electromagnetic interference) materials with outstanding shielding effectiveness were explored over the last years to solve the problems in electronic devices. Magnetic absorbing materials have extensive bandwidth, good impedance matching, and excellent absorption features. In the present study, Sm-Mn Sr-doped M hexaferrites with Sr1-xSmxFe12-yMnyO19 whereas (x= 0.00, 0.025, 0.05, 0.075, y = 0.00, 0.25, 0.5, 0.75) were prepared by the chemical route. XRD, FESEM, HRTEM, FTIR, VSM, and VNA are used to evaluate the properties of the Sm-Mn doped Sr-based M-type hexagonal ferrite. The XRD (X-ray diffraction) results revealed the presence of a hexagonal phase in the prepared samples. Rietveld refinement also confirmed the phase purity for the Sm-Mn doped Sr-based M-type hexagonal ferrites. The FESEM (Field emission scanning electron microscopy) and HRTEM (High-resolution transmission electron microscopy) images revealed the hexagon-type shapes of the particles in the Sm-Mn doped Sr-based M-type hexagonal ferrites. The FTIR (Fourier transform infrared spectroscopy) spectra showed the 446–620 cm-1 lines, confirming the presence of the tetrahedral and octahedral phases of hexagonal ferrites. Dielectric and electromagnetic shielding effectiveness (SE) parameters are evaluated for Sm-Mn doped Sr-based M-type hexagonal ferrite. The electromagnetic parameters, such as complex refractive index, absorption and impedance, are also investigated for the Sm-Mn doped Sr-based hexagonal ferrite powder with x=0.075, y=0.75 having epoxy resin with 20 wt%, 30 wt% and 50 wt% samples, respectively. SE parameters are higher at more extensive filler loading. The green shielding index was found higher for Sm-Mn doped Sr-based hexagonal ferrite powder with x=0.075, y=0.75 having 20 wt% epoxy resin and decreased with filler loading. It is found the epoxy/Sm-Mn doped Sr-based M-type hexagonal ferrites-based composites are excellent absorbers in the Ku band. The investigated absorbers could be the best candidates for next-generation EMI green shielding absorbing devices and applications.

Caffeic-Acid-Functionalized MWCNTs and PEDOT:PSS Formed Composite Flexible Films with "Reinforced Concrete" Structure for Electrical Heating and EMI Shielding.

Nowadays, flexible multifunctional composites are attracting much attention and are practically being used in various emerging electronic devices. However, most composites suffer from the disadvantages of high loadings of conductive fillers, complicated preparation processes, and low energy conversion efficiency. In this article, Caffeic acid-modified multiwalled carbon nanotubes (C-MWCNTs)/poly(3,4-ethylene dioxythiophene):polystyrene sulfonic acid (PEDOT:PSS)/polyimide (PI) composite films (CPFs) were prepared using a simple layer-by-layer deposition method. The "reinforced concrete" structure of the C-MWCNTs/PEDOT:PSS layer ensures high electrical conductivity of the film, while the PI layer provides excellent mechanical properties (72.69 MPa). The composite film exhibits excellent electrothermal response and thermal stability up to approximately 125 °C at 5 V. In addition, the good conductivity of the film provides its electromagnetic shielding effectiveness (32.69 dB). With these advantages, we expect that flexible CPFs will be widely utilized in wearable devices, electromagnetic interference (EMI) shielding applications, and thermal management of personal or electronic devices.

Study on the microstructure, optical performance, and electromagnetic shielding effectiveness of Al-Ag thin films for variable annealing time

Herein, the magnetron co-sputtering method is employed to fabricate 9 nm 5 mol% Al-Ag thin films, and subsequently annealing treatment is performed. The effect of the annealing time on the structure, optical, and electromagnetic (EM) shielding performance of them is thoroughly studied. It is observed that by subjecting the films to the appropriate annealing time, the Ag granules undergo a transformation into a planar growth structure and make the integrated performance of Al-Ag thin film more exceptional. Compared with other annealing time, when it is 5 min, the obtained Al-Ag thin films display the homogenous and smooth surface morphology. Moreover, it exhibits excellent optical properties with the highest transmittance value of 89.6% at 550 nm, and meanwhile the shielding effectiveness reaches a peak value of 28.7 dB. These characteristics render the Al-Ag thin films highly practical and valuable for EM shielding windows with high transmittance.

The effects of ZnO powder and different fiber types used in tuff/calcite-based geopolymers on electromagnetic shielding effectiveness

Electromagnetic (EM) shielding has become increasingly important in our modern world due to the growing use of electronic devices, which poses risks of EM pollution and its adverse effects on humans. Many studies have explored the incorporation of various additives into geopolymer mixes to enhance their EM shielding properties. This study investigates the impact of tuff/calcite-based geopolymers reinforced with three different types of fibers (Polypropylene, Steel, and Carbon) and varying percentages (2.5 %, 5 %, and 10 %) of ZnO powder on EM shielding effectiveness. Compressive strength, flexural strength, water absorption, length change tests, and EM shielding (900–6000 MHz at every 100MHz step) measurements were performed on geopolymer samples. Optimal shielding performance was achieved by the addition of 10 % ZnO by volume alongside carbon fiber. This combination resulted in a total shielding value of −78.92dB at a bandwidth of 2800MHz.

Enhanced electromagnetic shielding with ultrathin VGNs-Metal hybrid structures

Designing and preparing lightweight electromagnetic shielding materials at the micron level is crucial for aerospace and military applications. Vertical graphene nanowalls (VGNs) offer high efficiency for electromagnetic shielding due to attributes such as high carrier mobility, porosity, and low density. This study presents the preparation of ultra-thin VGNs/metal stacked films via plasma-enhanced chemical vapor deposition (PECVD) for VGNs, and combined electron beam evaporation (EBE) with cyclic PECVD for metal layers. The PECVD technique ensures homogeneity and controllable thickness of the VGNs. The experimental results demonstrate that the interface between the VGNs and the metal layer exhibits good interfacial contact, resulting in high carrier mobility. Furthermore, incorporating a metal layer with a thickness ratio of 10 % significantly enhances conductivity by an order of magnitude. The hybrid structures exhibit remarkable electromagnetic shielding effectiveness per unit thickness (∼5300 dB mm−1) evaluated in the X-band range (8–12 GHz). Stacked films as thin as 0.01 mm achieve up to 53.4 dB of electromagnetic shielding. Finite element simulations indicate that the presence of opposing electric fields at the graphene-metal interface contributes to higher ohmic loss. The coupling effect at the interface significantly contributes to the material's excellent electromagnetic shielding effectiveness.

Flexible multilayer MXene/Polyimide composite film with excellent electromagnetic interference shielding and photothermal conversion performance

The development of flexible, thin, multifunctional materials represents a strategic advancement for the creation of next-generation wearables that offer both electromagnetic shielding and thermal management. This study introduces the fabrication of a multilayer MXene/polyimide (MXene/PI) composite film, demonstrating significant electromagnetic shielding effectiveness (EMI SE) and photothermal conversion efficiency through a layer-by-layer casting technique. When the MXene content is 29.7 wt%, the alternating multilayer MXene/PI composite film can reach a high EMI SE of 23.3 dB at 0.26 mm thickness, and when the MXene content is 45.7 wt%, the EMI SE can reach a maximum of 40.7 dB, which has a significant advantage over other materials. This superior performance exceed that of alternative materials, owing to the multilayer MXene construction that magnifies electromagnetic wave reflection losses. Furthermore, the film displays a rapid and sensitive photothermal response under laser irradiation, achieving temperatures up to 93°C at a 0.5 W/cm2 density. Impressively, at 0.4 W/cm2, it maintains a stable long-term saturation temperature over 40 cycles, showing its potential in applications such as photothermal sensors, personal heating, and muscle protection.

Enhancing electromagnetic shielding performance of cement-based materials using industrial waste copper swarf

With growing concerns over electromagnetic interference (EMI) in our surrounding environment, the impact of electromagnetic waves (EMW) on human health and electronic devices is increasingly drawing attention. This study explores the preparation methods of cement-based electromagnetic shielding materials by incorporating copper swarf waste produced by metal processing factories into the cement. It is realizing the recycling and utilization of discarded metal resources and producing copper swarf cement-based materials (CSCBM). Mechanical properties, electrical conductivity, related electromagnetic parameters and shielding efficiency of the material under the X-band were discussed in detail. This study provides new insights into the future recycling and utilization of copper swarf, as well as offering a reference investigation for the recycling of other types of metal swarf. In this study, compressive and flexural strengths were considered, while the morphology and position of copper swarf within the specimens were examined from both macroscopic and microscopic perspectives, taking into account the impact of the morphology and position of copper swarf on compressive and flexural strengths. Through discussions on complex permittivity and resistivity, it was concluded that copper swarf enhances electromagnetic shielding effectiveness by increasing the complex permittivity and reducing the matrix resistivity. Furthermore, based on previous studies, this research provides a theoretical analysis of the negative magnetic permeability phenomenon, offering support for future investigations into negative magnetic permeability phenomena. Under an electromagnetic field, eddy currents will be generated inside the CSCBM, which makes the magnetic permeability of the CSCBM negative. This research forms a foundation for enhancing the EMI shielding effects of cement-based materials using industrial copper swarf.

Investigations on morphology, tribology, rheology, thermo-mechanical properties, and EMI shielding of WC/MWCNT nanohybrids in polypropylene

This study is focused to explore the synergism of dual nanofillers (tungsten carbide (WC) and multiwalled carbon nanotubes (MWCNTs)) in melt extruded PP composites. The synergy of fillers in PP enhanced the elastic modulus, tensile strength, and critical stress intensity factor by 141.8%, 35.4%, and 62.6%, respectively, at an optimum filler content of 1 wt% of WC and 2 wt% of MWCNTs. In the hybrid composites, activation energy to initiate thermal decomposition raised by 78% and wear resistance increased by 93%, and the hybrid composites exhibited enhanced reflectivity in the X band region, which contributed to high electromagnetic shielding effectiveness. The improvement in the properties makes the current hybrid composite system an ideal candidate in application sectors where high modulus, energy absorption, and thermal stability are required.

Simulation Analysis of Electromagnetic Environment Effect and Shielding Effectiveness for VPX Chassis under Plane Wave Radiation

The chassis based on the VPX bus standard structure has been widely applied to the fields of vehicle, missile, radar, etc. In this paper, we analyze the electromagnetic environment effect on VPX chassis via the CST software, and investigate the electromagnetic coupling characteristics of VPX chassis under 20 v/m plane wave radiation according to the RS103 test defined in the MIL-STD-461G standard. By simulation, we analyze the electromagnetic coupling paths of the VPX chassis, find the key positions of the electromagnetic protection such as the air intake, air outlet, trapdoor, and panel gaps, and we propose the electromagnetic protective measures for the weak parts of the VPX chassis. The electromagnetic shielding effectiveness before and after protection design is evaluated. Finally, the simulation results are verified by the experiments. It has guiding significance for the electromagnetic protection design of VPX chassis.

High-Compressive, Elastic, and Wearable Cellulose Nanofiber-Based Carbon Aerogels for Efficient Electromagnetic Interference Shielding.

Developing excellent electromagnetic interference (EMI) shielding materials with robust EMI shielding efficiency (SE), high mechanical performance, and multifunctionality is imperative. Carbon materials are well recognized as promising alternatives for high-performance EMI shielding, but their high brittleness greatly hampers their applications. In this work, a cellulose nanofiber/reduced graphene oxide-glucose carbon aerogel (C-CNFs/rGO-glu) with high compression, elasticity, and excellent EMI shielding performance was fabricated by directional freeze-drying followed by carbonization. Specifically, the height and stress retention are 88% and 90.9%, respectively, after 100 cycles of compression release at a high strain of 70%. The electromagnetic shielding effectiveness of the aerogels reached 67.5 dB and presented an absorption-dominant shielding mechanism with a 97.5% absorption loss ratio. Further, the carbon aerogel could capture subtle electrical signals to monitor different human behaviors and showed excellent heat insulation and infrared stealth performance.

Preliminary small-scaled thermal resistance testing of a masonry wall with enhanced electromagnetic shielding effectiveness

This study presents the preliminary results of a small-scale masonry wall thermal resistance (R-value) measurement. Two small-scale masonry walls were constructed using regular and antimony tin oxide (ATO)-containing bricks. ATO has shown potential for improving the protection against electromagnetic radiation penetration. R-values of the walls were measured using a FluxDAQ device equipped with a heat flux sensor and two temperature sensors for obtaining the heat flux and inside and outside temperatures during the measurement. Furthermore, the thermal conductivity (λ) of the bricks was measured by using the Fox200 Heat Flow Meter. Both results can be used for determining a walls’ thermal transmittance (U-value), which is often used for describing the energy losses and as a measure of a wall's energy efficiency. This research sought to investigate whether there is a correlation between the results obtained by the small-scale masonry wall and Fox200 device. Ultimately, this experiment aims to verify whether the small-scale masonry wall non-standard method described herein can provide approximately similar results to the standardised method.

Functionalized lignin nanoparticles assembled with MXene reinforced polypropylene with favorable UV-aging resistance, electromagnetic shielding effects and superior fire-safety

Deterioration in mechanical performances and aging resistance due to the introduction of flame retardants is a major obstacle for bio-based fire-safety polypropylene (PP). Herein, we reported a kind of functionalized lignin nanoparticles assembled with MXene (MX@LNP), and applied it to construct the flame-retardant PP composites (PP-MA) with superior fire safety, excellent mechanical performance, electromagnetic shielding effects and aging resistance. Specifically, the PP-MA doped with only 18 wt% flame-retardant additives (PP-MA18) achieved the UL-94 V-0 rating. In comparison to pure PP, PP-MA18 presented a greatly decreased peak of heat release rate (pHRR), total heat rate (THR), and peak smoke production rate (pSPR) by 79.7 %, 69.0 % and 75.8 %, respectively, and satisfactory decrease in total flammable and toxic volatiles evolved. The formed fine solid microstructure of carbon residuals effectively promoted the compactness of char layers. More importantly, the nano-effect and the strong interface interaction between the complexed MX@LNP and PP enhanced the tensile strength (45.78 MPa) and elongation at break (725.95 %) of PP-MA. Additionally, the significant ultraviolet absorption and electromagnetic wave dissipation performance of MXene and lignin enabled excellent aging resistance and electromagnetic shielding effects of PP-MA compared with PP. This achieved MX@LNP afforded a novel approach for developing flame retardant materials with excellent application performance.

3D interconnected graphene nanoplatelets and nickel ferrite based silicone rubber foams for effective electromagnetic interference shielding and thermal insulation performance

In the present study, porous composite foams made of silicon rubber (SR), graphene nanoplatelets (GnP), and nickel ferrite (NiFe2O4) nanoparticles were developed using the salt template approach. SR act as a 3D porous network, the conductive channel provided by graphene nanoplatelets and the magnetic and dielectric loss provided by the NiFe2O4 and the composite foam as a whole showed absorption-dominated EMI shielding due to synergism between GnP and NiFe2O4. Without NiFe2O4, the total EMI SE is 23 dB, while different NiFe2O4 weight percentages (0%, 3%, 6%, & 9%) increase the SET up to 36.7 dB. The thermal conductivity of this prepared sample is found to be 0.0313 Wm−1K−1 for 9 wt% filler content of NiFe2O4. It shows a moderately low value as compared to existing polymer composites. The resulting SR/GnP@NiFe2O4 composite foams, which are lightweight, strong, and multifunctional, have straightforward synthesis procedures and have a myriad of possible uses for EMI shielding systems and thermal insulations in the disciplines of aerospace, military engineering, electrical engineering and electronics.

Multi-Functional and Flexible Nano-Silver@MXene Heterostructure-Decorated Graphite Felt for Wearable Thermal Therapy.

Wearable heaters with multifunctional performances are urgently required for the future personal health management. However, it is still challengeable to fabricate multifunctional wearable heaters simultaneously with flexibility, air-permeability, Joule heating performance, electromagnetic shielding property, and anti-bacterial ability. Herein, silver nanoparticles (AgNPs)@MXene heterostructure-decorated graphite felts are fabricated by introducing MXene nanosheets onto the graphite felts via a simple dip-coating method and followed by a facile in situ growth approach to grow AgNPs on MXene layers. The obtained AgNPs@MXene heterostructure decorated graphite felts not only maintain the intrinsic flexibility, air-permeability and comfort characteristics of the matrixes, but also present excellent Joule heating performance including wide temperature range (30-128 °C), safe operating conditions (0.9-2.7V), and rapid thermal response (reaching 128 °C within 100 s at 2.7V). Besides, the multifunctional graphite felts exhibit excellent electromagnetic shielding effectiveness (53dB) and outstanding anti-bacterial performances (>95% anti-bacterial rate toward Bacillus subtilis, Escherichia coli and Staphy-lococcus aureus). This work sheds light on a novel avenue to fabricate multifunctional wearable heaters for personal healthcare and personal thermal management.

Hybrid functional membranes through layer-by-layer assembly of Ti3C2Tx MXene and gelatin-stabilized calcium phosphate nanospheres

MXene-based membranes exhibit promising properties for various applications; however, pure MXene membranes lack sufficient environmental stability and mechanical strength. This work demonstrates that incorporating gelatin-stabilized amorphous calcium phosphate (Gel-ACP) nanospheres into MXene membranes via layer-by-layer assembly significantly enhances flexibility and mechanical strength while retaining electrical conductivity. A pressure-assisted stacking technique was introduced to efficiently fabricate membranes with tunable thickness not achievable through single filtration steps. The Gel-ACP nanospheres, synthesized by co-precipitation of calcium phosphate within gelatin solution, provided a ductile and cytocompatible reinforcement that augmented the properties of the MXene matrix. Direct mixing of the components led to particle aggregation and non-uniform dispersion. In contrast, controlled layer-by-layer nanostructuring maintained membrane conductivity around 102 Scm−1 while dramatically improving mechanical integrity. The optimized hybrid membranes exhibited specific electromagnetic shielding effectiveness of ∼21,000 dBcm2g−1 and withstood over 90 kPa vacuum pressure without rupture, six times higher than pure MXene membranes. Cytocompatibility was confirmed by the proliferation of human mesenchymal stem cells on the membranes. Moreover, the layered membrane exhibited excellent adhesion to bone-mimicking structures, indicating potential utility for bone tissue engineering. Overall, this work provides new design principles for engineering hybrid membranes through controlled multicomponent assembly to overcome intrinsic limitations and impart multifunctionality.

Electromagnetic shielding effectiveness of needle-punched composite nonwoven fabrics with stainless steel fibres

In the study, electromagnetic shielding efficiency (EMSE) absorption and reflectivity properties of fabric produced from staple stainless-steel fibres and recycled staple polyester fibres by carding and needling technologies were investigated. The bi-component core/sheath polyester fibres at a fixed ratio of 20% in producing all nonwoven fabrics were used. The staple stainless-steel fibres and recycled staple polyester fibres were blended at 13 different ratios such as 1%, 2.5%, 5%, 7.5%, 10%, 12.5%, 15%, 17.5%, 20%, 22.5%, 25%, 27.5%, 30%. The fibre webs were formed at wool type carding machine and then the folded webs were bonded mechanically with needle punching machines. Half of the produced nonwoven composite fabrics were bonded by thermal bonding technology with oven and calender machines. As the conductive fibres were costly, the study aimed to obtain optimum shielding effectiveness with the usage of minimum conductive fibres. Electromagnetic shielding properties, absorption and reflection characteristics of needle-punched nonwoven fabrics with calendered or un-calendered were performed by coaxial transmission line method according to ASTM-D4935-10 in the frequency range of 15 MHz to 3000 MHz. It is a known fact that electromagnetic shielding effectiveness increases with the increase in the amount of conductive fibre. It was found that nonwoven fabric produced with a usage of 17.5% stainless steel fibre has at least 90% electromagnetic shielding percentage in general use with 15 dB at a frequency of 1800 MHz. Increased stainless steel fibre content in nonwoven fabrics resulted in decreased nonwoven fabric thickness and tensile strength. Such a nonwoven composite material with electromagnetic shielding property could be used for construction and building applications.