Electrical Wire Explosion Research Articles

Structure and Magnetic Properties of Iron Oxide Nanoparticles Subjected to Mechanical Treatment

Iron oxide nanoparticles have been fabricated using the electric wire explosion (EWE) technique. The structure and magnetic properties of the nanoparticles have been analyzed before and after mechanical grinding in a ball mill for different time periods, focusing on potential bioapplications. The phase composition of the nanoparticles (70% Fe3O4, 30% Fe2O3) has remained unchanged despite the mechanical effects. The average nanoparticle size has not been affected either. The observation of the Verwey transition in the studied nanoparticles, along with the structural data, provides a better understanding of the physical properties of EWE ensembles of nanoparticles in different states. The analysis of the structure and magnetic properties reveals the development of a material with a high level of internal stress. This finding may be of interest for bioapplications due to its potential impact on the material performance.

Synthesized Cu nanoparticles by the Electric Wire Explosion Method for Anti-Candida Albicans application

The copper nanoparticles Cu NPs were successfully prepared via laser triggering wire explosion technique at different explosion voltages (4, 5 and 7 KV). It was observed through atomic force microscopy examinations that the prepared powders are highly homogeneous and contain agglomerations resembling regularly distributed protrusions and that the homogeneity increases with increasing explosion voltage. The examination of the fourier transform infrared spectroscopy showed bonds and functional groups belong to CuO and Cu2O. Antifungal activity tests showed the efficiency of the prepared powders in eliminating Candida albicans, especially the Cu nanopowder prepared at 7KV and a concentration 200 µg/mL.

The structural characteristics of nano-copper thin films produced via laser-assisted electric wire explosion process

Abstract Due to the wide range of important applications, the metal and metal oxide nanoparticles have increasing demand, so that many methods and technologies attempted to produce it. The Electric Wire Explosion (EWE) method is the most established method to produce nanometals and metal oxides in the form of either powders or thin films. In this study, copper and copper oxide films were prepared via electric wire explosion method with a developed laser igniting spark gap switch. The Cu thin films were prepared at different explosion voltages (4, 5 and 7kV) and then their structural properties were studied. The results show that the produced copper/copper oxides nanoparticles of thin films increased as the exploding voltage increased. The XRD test shows that the films crystallite size increased as the exploding voltage increased. FE-scanning electron microscope (FE-SEM) images, are shows the decrease of grain size of thin films as the explosion voltage increase.

Energy release in electrical wire explosions coupled with energetic materials

Energy release in electrical wire explosions coupled with energetic materials

Microstructure and electromagnetic wave absorption properties of FeCo/graphene composites prepared by electrical wire explosion method

Microstructure and electromagnetic wave absorption properties of FeCo/graphene composites prepared by electrical wire explosion method

Shock wave generated by composite energetic material driven by electrical non-penetrating wire explosion plasma.

Underwater shock wave technology can realize dynamic rock fracture, which is helpful to increase oil and gas reservoir permeability. It can realize the efficient exploitation of medium and low maturity oil and gas resources. In practical application, the shock wave parameters require not only high intensity but also safety and controllability. To meet these requirements, insensitive composite energetic materials driven by electrical wire explosion plasma were proposed, which is one of the most promising methods. However, when in use, the load assembly process containing wires and energetic materials is complex. In this paper, a new type of energetic material load is proposed, using non-penetrating wire to drive composite energetic material. It can simplify the production process of the energetic load and produce acceptable shock wave parameters. The test results show that both the energy deposition of the wire and the shock wave intensity decrease under a non-penetrating wire structure. However, the shock wave intensity is still higher than that of the underwater electrical wire explosion. Based on schlieren diagnosis, it is found that the composite energetic material is gradually driven, and the energy release is not concentrated. In addition, the "non-wire" structure driving condition was discussed in contrast. Under this condition, the process of ionization channel establishment in composite energetic materials is random. The shock wave intensity is weak because the composite energetic material is in the process of slow detonation.

Electric Explosion of Thin Wires (a Paradigm Shift)

Electric Explosion of Thin Wires (a Paradigm Shift)

A novel method for investigating the underwater explosion loads and bubble evolution

This paper presents an innovative experimental method for studying the evolution and energy output characteristics of underwater explosion bubbles. We independently constructed an experimental testing system for underwater electrical wire explosions (UEWE), in which electrodes connected to a metal wire serve as the load, and underwater explosions are initiated through instantaneous high-voltage discharge. By varying the diameter of the metal wire and configuring parallel wire arrays, we analyzed and discussed the explosion characteristic parameters and the current–voltage (I–V) signals under different conditions. The maximum bubble radius of the underwater metal wire explosion was compared with the corresponding equivalent explosive simulation results, and a numerical model for underwater metal wire explosion equivalent to explosive detonation was established. Subsequently, we discussed the characteristics of bubble generation and evolution under various conditions, clarifying the similarities and differences between wire explosions and explosive detonations. On this basis, we explored the propagation laws of shock waves and secondary pulsation waves (SPW) under different conditions. We also calculated and analyzed energy output characteristic parameters, such as shock wave energy and bubble energy. The results indicate that there are significant differences between copper wire and aluminum wire loads in UEWE. For copper wires with a diameter greater than 0.4 mm, the shock wave overpressure peak value significantly decreases, while for aluminum wires with a diameter greater than 0.5 mm, it slightly decreases. Both metals exhibit similar trends in parallel wire arrays, with the shock wave overpressure peak value initially increasing and then decreasing as the number of wires increases. Unlike underwater explosive detonations, the SPW peak value in UEWE may exceed that of the shock wave. For single wires, the SPW peak value of copper wires is generally higher than that of aluminum wires, but in wire arrays, the trend is reversed. The multi-wire parallel connection can improve the energy conversion efficiency of the shock waves. However, for bubble energy, under all conditions, a single aluminum wire with a diameter of 0.5 mm produced the maximum bubble energy, reaching 1023.1 J. These findings provide new insights into the energy features of UEWE.

Research on the sub-millisecond underwater electrical wire explosion process

Abstract Underwater electric wire explosion (UEWE) has great potential as a shockwave source for medical and industrial applications. This paper focuses on the process of the sub-millisecond underwater electrical wire explosion (smUEWE). The study compared the smUEWE and the microsecond underwater electrical wire explosion, which revealed the occurrence of partial vaporization under smUEWE, leading to the formation of bamboo-shaped cavities and frontal shock waves. The experiments of smUEWE were carried out under different stored energy, the results indicated the plasma shrinkage and cavity separation during the overall ionization process. Additionally, the study observed secondary breakdown caused by the uneven distribution of ionization products. An analysis was conducted on smUEWE considering partial vaporization, which divided the electrical explosion into a positive feedback process which promoted the axial instability and a negative feedback process which formed the uniform plasma channel. The analysis results was consistent with the experimental results.

Synthesized Cu nanoparticles by the Electric Wire Explosion Method for Anti-Candida Albicans application

The copper nanoparticles Cu NPs were successfully prepared via laser triggering wire explosion technique at different explosion voltages (4, 5 and 7 KV). It was observed through atomic force microscopy examinations that the prepared powders are highly homogeneous and contain agglomerations resembling regularly distributed protrusions and that the homogeneity increases with increasing explosion voltage. The examination of the fourier transform infrared spectroscopy showed bonds and functional groups belong to CuO and Cu2O. Antifungal activity tests showed the efficiency of the prepared powders in eliminating Candida albicans, especially the Cu nanopowder prepared at 7KV and a concentration 200 µg/mL.

Influence of the Glycidyl Azide Polymer on the Energy Release of Aluminum Sub-Micron Particles under Ultrafast Heating Rates Stimulated by Electric Explosion and Solid Laser

Glycidyl azide polymer (GAP)-coated sub-micron aluminum (sub-mAl@GAP) particles exhibit higher heat release than their uncoated counterparts under low heating rates. However, their application in explosives has been hindered due to a lack of understanding of their energy release characteristics under heating rates of detonation levels. To address this problem, the energy release performances of sub-mAl@GAP particles under ultrafast heating rates stimulated by an electric explosion of wire and high-energy laser were studied. The results showed that the reaction of sub-mAl@GAP particles was more violent than that of an uncoated counterpart under an electric explosion stimulus. Additionally, the reaction time of the former was 0.4 ms shorter than that of the latter. In addition, the propagations of shock waves of the sub-mAl@GAP and sub-mAl were analyzed. The propagation distances of shock waves of the sub-mAl@GAP were all longer than those of sub-mAl under laser fluences of 0.5 J/cm2, 1.2 J/cm2, and 2.4 J/cm2. The distance difference gradually increased with the decrease in the laser fluence. Under a laser fluence of 0.5 J/cm2, the velocity and distance differences of the sub-mAl@GAP and sub-mAl were both the largest due to the energy contribution from the GAP. In conclusion, the fast decomposition rate of the GAP and its energy contribution would benefit the energy release of sub-mAl under ultrafast heating rates.

Effects of wire size on electrical and shock-wave characteristics in underwater electrical explosions of aluminum wires

Initial wire resistance is an important parameter in an underwater electrical wire explosion because it directly affects the discharge characteristics of the circuit and indirectly affects the explosion and shock-wave generation. This paper presents a study on how the initial resistance affects electrical and shock-wave characteristics of underwater electrical explosions of aluminum wires with an initial energy storage of ∼53.5 kJ under the optimal mode. Load voltage, circuit current, and shock-wave pressure were recorded and analyzed. The experimental results show that the average of the discharge channel resistance and the total energy deposition all increase with the initial resistance. In addition, there is no simple functional relationship between the energy deposition during the phase transition process and the initial resistance, while the energy deposition during the plasma growth process increases with the initial resistance. As for shock waves at ∼33 cm, it is observed that when the initial resistance increases from 674.82 to 1581.60 μΩ, the peak pressure, energy density, and impulse increase from 12.65 MPa, 2.67 kJ/m2, and 964.51 Pa s to 42.37 MPa, 18.21 kJ/m2, and 1940.42 Pa s, respectively. In other words, for the optimal mode, an underwater electrical explosion with thinner and longer wire is more conducive to generating strong shock waves in the far-field regime. These results should help select loads for underwater electrical wire explosions in engineering applications.

Electrical conductivity of copper in the low temperature region of warm dense matter

In this study, electrical conductivity of copper in the low temperature part of a warm dense matter regime is investigated utilizing underwater electrical wire explosion. Specifically, for the vapor/plasma region with a density of ∼0.01 normal density, temperature up to 10 kK, and the liquid–vapor two-phase region below the binodal curve, the electrical conductivity of copper is measured as a function of density and temperature by means of shadowgraph imaging, spectroscopy, and electrical measurements. In this region, anomalous temperature dependence and characteristics originated from a phase transition are found. Based on the careful analysis of experiments and model calculations, it is revealed that bound electrons, in addition to free electrons, contribute significantly to the electrical conductivity in the vapor/plasma region, and that the associated phase transition kinetics play a substantial role in adequately describing the behavior in the liquid–vapor two-phase region. An improved electrical conductivity model emerging from our combined experimental and theoretical study that accounts for the characteristics in the low temperature regime of the warm dense matter is presented.

Electrical properties of different materials studied by sub-microsecond underwater electrical explosions of single wires

Results of an experimental research and one-dimensional hydrodynamical simulations of critically damped sub-microsecond timescale underwater electrical explosions of wires made of 12 different materials are presented. Using current and voltage waveforms, streak shadow images of the shocks generated in water and wire expansion obtained by one-dimensional hydrodynamic simulations, the maximal values of the energy density, energy density deposition rates, and specific action integrals were determined. It is shown that for all study materials, the deposited energy density significantly exceeds the energy density required for the solid–liquid phase transition but is substantially smaller to induce a full liquid–vapor phase transition of the wire. At the time when the maximal value of the deposited power is realized, the deposited energy densities were found to be larger than the atomization energy for all materials. Estimates of the plasma parameters show that the explosion of the wires can be characterized by a high resistance and lowly ionized weakly coupled plasma. Three groups of materials were distinguished by either decrease, plateau, or increase in the resistance after the maximum of the deposited power. It was confirmed that the observed maximum Planckian temperature for all wire material does not exceed 6000 K due to the “bath” effect and that there is a correlation between the wire radial expansion and the strong shock wave velocities.

The Structural Properties of Nano-Coppers Synthesized via the Electric Wire Explosion Method and Application as Anti- Escherichia coli Bacterial

In this research, copper nano powders Cu NPs were successfully prepared via laser triggering wire explosion technique at different explosion voltage (4, 5 and 7 KV). It was observed through X-ray diffraction examinations that the prepared powders have a polycrystalline structure and their characteristic peaks correspond to copper and copper oxide. FE-scanning electron microscopy images showed that the prepared powders had a nanostructure and regular morphology, and the regularity increased with increasing explosion voltage. Antibacterial activity tests showed the efficiency of the prepared powders in eliminating Escherichia coli bacteria, especially the powder prepared at 7KV voltage and at concentration 200 µg/mL.

Underwater electrical wire explosions under different discharge types: An experimental study with high initial energy storage

In this study, underwater electrical explosions of aluminum wires of various sizes were carried out with an initial energy storage of ∼53.5 kJ. Two piezoelectric probes were adopted to record the pressure waveforms. The experiments were divided into different discharge types, and the statistical properties of the electrical and shock-wave parameters of the different discharge types were compared. The experimental results show that there are three discharge types, called type A (breakdown type), type B (transition type), and type C (matched type). The three types differ in the resistance characteristics of the plasma channel during the plasma growth process, which are determined from the average electrical field strength and the remaining energy in the circuit at the peak voltage. Shock waves from type C discharges are more likely to exhibit a higher peak pressure, a larger impulse, and a higher energy density than the other types. However, using a matched wire that matches a specific discharge type, a high peak pressure, large impulse, and high energy density can also be achieved under type A or type B discharges. For example, the maximum peak pressures at ∼33 cm under type B and type C discharges are 38.7 and 42.4 MPa, respectively. These results provide significant guidance for load selection in underwater electrical wire explosion engineering applications.

Synthesis and Properties of Ni-CNT Nanocomposites Using Electrical Explosion of Wire in Different Conditions

Synthesis and Properties of Ni-CNT Nanocomposites Using Electrical Explosion of Wire in Different Conditions

Synthesis of FCC structure Fe10Co25Ni34Cu23Al8 high-entropy-alloy nanoparticles by electrical wire explosion: For electromagnetic wave absorption

In this paper, Fe10Co25Ni34Cu23Al8 high-entropy-alloy nanoparticles have been synthesized by the in situ instantaneous electrical wire explosion method. Based on the thermodynamic parameters of the face-centered cubic phase of high-entropy-alloy, the parameters of the five kinds of wires were calculated and controlled, and the stable face-centered cubic structure with good crystallinity was synthesized in one step. The influence of the energy deposition during the electrical explosion on the nanoparticles and their electromagnetic absorption performance was explored. The results show that the face-centered cubic structure high-entropy-alloy with high crystallinity has better electromagnetic wave absorption performance when the energy deposition of the wires is increased. The minimum reflection loss can reach −39.37 dB at 15.34 GHz when the thickness is 1.9 mm and the effective absorption bandwidth is 6.63 GHz. It can provide a strategy for the microstructure and morphology design of high-entropy-alloy nanoparticles in electromagnetic wave absorption and magnetism in the electronics industry.

Improvement of the Hydrogen Storage Characteristics of MgH2 with Al Nano-Catalyst Produced by the Method of Electric Explosion of Wires.

A new composite with a core-shell structure based on magnesium hydride and finely dispersed aluminum powder with an aluminum oxide shell was mechanically synthesized. We used magnesium chips to produce magnesium hydride and aluminum wire after exploitation to produce nano-sized aluminum powder. The beginning of the hydrogen release from the composite occurred at the temperature of 117 °C. The maximum desorption temperature from the MgH2-EEWAl composite (10 wt.%) was 336 °C, compared to pure magnesium hydride-417 °C. The mass content of hydrogen in the composite was 5.5 wt.%. The positive effect of the aluminum powder produced by the electric explosion of wires method on reducing the activation energy of desorption was demonstrated. The composite's desorption activation energy was found to be 109 ± 1 kJ/mol, while pure magnesium hydride had an activation energy of 161 ± 2 kJ/mol. The results obtained make it possible to expand the possibility of using magnesium and aluminum waste for hydrogen energy.

Experimental Study of Energy Design Optimization for Underwater Electrical Shockwave for Fracturing Applications

Underwater electrical shockwave can be used as a waterless, chemical-free, and environmentally friendly fracturing technique. A detailed experimental study was performed to develop a correlation between the optimum energy required to generate a shockwave that could be used in fracturing rock samples with the wire weight and diameter as independent factors. In addition, the effect of the water volume on the Underwater Electrical Wire Explosion (UEWE) was investigated to quantify the effect of the wellbore fluid volume in the fracturing process. The effect of increasing the discharge energy on the current waveform rising rate, peak amplitude, and fracturing geometry was investigated. A baseline for implementing the shockwave fracturing method on cement and limestone samples was defined to be used in future work. The results show that the water volume has a significant effect on the results of the experiment. A correlation was developed that defined the optimum minimum energy required to burn a certain wire weight with consideration to the wire diameter. Using the optimum required energy or higher will increases the current peak amplitude with the same current waveform rise rate, which leads to higher energy deposition into the wire and prevents the premature breakdown of the wire. The generated shockwave was used to successfully fracture cement and limestone cubic samples.