Electric Current Pulses Research Articles

Electroplasticity constitutive modeling of aluminum alloys based on dislocation density evolution

Electrical current can effectively improve the plasticity of metallic materials. The tensile deformation behavior of Al alloys under the pulsed electrical current assisted quasi-static unidirectional tension (EAT) has been investigated. Materials under the EAT exhibits periodic electro-softening and strain-hardening behaviors, i.e., a ratchet shape mechanical response. However, establishing a constitutive model to accurately predict the ratchet shape mechanical behavior, especially during the EAT interval, and accurately predicting the strain-hardening behavior of materials are critical issues that need to be solved urgently. In this study, based on the Taylor polycrystalline model, thermal activation theory and dislocation density evolution theory, a two-parameter dislocation density electroplasticity constitutive model with forward and reverse dislocation density evolution was developed to describe the periodic coupling effect of the electro-thermal-mechanical fields during EAT. The tensile deformation behaviors of AA 6061-T6 and AA 7075-T6 under the effect of a pulsed electrical current were quantitatively predicted using the proposed constitutive model. The results show that the correlation coefficient between the predicted and experimental results of the constitutive model can reach 0.84–0.99, implying that the proposed constitutive model can accurately predict the complex electroplasticity behavior of Al alloys during EAT.

Energy-efficient picosecond spin-orbit torque magnetization switching in ferro- and ferrimagnetic films.

Electrical current pulses can be used to manipulate magnetization efficiently via spin-orbit torques. Pulse durations as short as a few picoseconds have been used to switch the magnetization of ferromagnetic films, reaching the terahertz regime. However, little is known about the reversal mechanisms and energy requirements in the ultrafast switching regime. In this work we quantify the energy cost for magnetization reversal over seven orders of magnitude in pulse duration, in both ferromagnetic and ferrimagnetic samples, bridging quasi-static spintronics and femtomagnetism. To this end, we develop a method to stretch picosecond pulses generated by a photoconductive switch by an order of magnitude. Thereby we can create current pulses from picoseconds to durations approaching the pulse width available with commercial instruments. We show that the energy cost for spin-orbit torque switching decreases by more than an order of magnitude in all samples when the pulse duration enters the picosecond range. We project an energy cost of 9 fJ for a 100 × 100 nm2 ferrimagnetic device. Micromagnetic and macrospin simulations unveil a transition from a non-coherent to a coherent magnetization reversal with a strong modification of the magnetization dynamical trajectories as pulse duration is reduced. Our results show the potential for high-speed magnetic spin-orbit torque memories and highlight alternative magnetization reversal pathways at fast timescales.

Virtual stimulation of the interictal EEG network localizes the EZ as a measure of cortical excitability.

Introduction: For patients with drug-resistant epilepsy, successful localization and surgical treatment of the epileptogenic zone (EZ) can bring seizure freedom. However, surgical success rates vary widely because there are currently no clinically validated biomarkers of the EZ. Highly epileptogenic regions often display increased levels of cortical excitability, which can be probed using single-pulse electrical stimulation (SPES), where brief pulses of electrical current are delivered to brain tissue. It has been shown that high-amplitude responses to SPES can localize EZ regions, indicating a decreased threshold of excitability. However, performing extensive SPES in the epilepsy monitoring unit (EMU) is time-consuming. Thus, we built patient-specific in silico dynamical network models from interictal intracranial EEG (iEEG) to test whether virtual stimulation could reveal information about the underlying network to identify highly excitable brain regions similar to physical stimulation of the brain. Methods: We performed virtual stimulation in 69 patients that were evaluated at five centers and assessed for clinical outcome 1year post surgery. We further investigated differences in observed SPES iEEG responses of 14 patients stratified by surgical outcome. Results: Clinically-labeled EZ cortical regions exhibited higher excitability from virtual stimulation than non-EZ regions with most significant differences in successful patients and little difference in failure patients. These trends were also observed in responses to extensive SPES performed in the EMU. Finally, when excitability was used to predict whether a channel is in the EZ or not, the classifier achieved an accuracy of 91%. Discussion: This study demonstrates how excitability determined via virtual stimulation can capture valuable information about the EZ from interictal intracranial EEG.

Quantum thermodynamics with a single superconducting vortex.

We demonstrate complete control over dynamics of a single superconducting vortex in a nanostructure, which we coin the Single Vortex Box. Our device allows us to trap the vortex in a field-cooled aluminum nanosquare and expel it on demand with a nanosecond pulse of electrical current. Using the time-resolving nanothermometry we measure [Formula: see text] joules as the amount of the dissipated heat in the elementary process of the single-vortex expulsion. Our experiment enlightens the thermodynamics of the absorption process in the superconducting nanowire single-photon detectors, in which vortices are perceived to be essential for a formation of a detectable hotspot. The demonstrated opportunity to manipulate a single superconducting vortex reliably in a confined geometry comprises a proof of concept of a nanoscale nonvolatile memory cell with subnanosecond write and read operations, which offers compatibility with quantum processors based either on superconducting qubits or on rapid single-flux quantum circuits.

Triphasic Pulse Stimulation Pattern in Cochlear Implant Users Assessed with Ecap Measure

The rationale for the use of three-phase stimulation for programming the processor of the cochlear implantation system (CI) in patients with deafness is presented. To study the possibilities of using a new type of stimulation, we selected patients after cochlear implantation, with signs of facial nerve stimulation (FNS) in postoperative period. All subjects were previously fitted with an audio processor with individual fitting maps based on traditional biphasic stimulation. The use of three-phase stimulation to prevent FNS is caused by the geometry of the electric current pulses, which allows to reduce the penetrating power of the charge in the tissues and eliminate the effect on the facial nerve, without resorting to reducing the levels of stimulation necessary to create a dynamic range of sound perception. Comparative data of the parameters and the results of audiological testing in 21 patients with symptoms of FNS with traditional (two-phase) and three-phase electrical pulses in the stimulation algorithm of the CI system are presented. The positive effect of three-phase stimulation has been established. The results of the study show a significant increase in sound perception indicators when switching to a three-phase stimulation algorithm.

Evaluation of low voltage on electrical cables using microct and COMSOL Multiphysics

Safety and quality are critical challenges in electrical engineering and unscheduled system outages caused by device failures present a significant concern. One of its main causes is the presence of air voids in the insulating layer of power cables. The main objective of this work was to evaluate the effect of current pulses, which generally occurs in transients, on the proliferation of voids in the insulating layer of electrical cables. X-ray microtomography (microCT) was used in the identification and analysis of air voids in aluminum (Al) and copper (Cu) electrical cables, with different cross-sectional areas, before and after electrical current pulses. The results showed an increase in voids caused by current pulses and an increase in electromagnetic fields and temperature inside the conductor. Furthermore, it was observed that the current pulses applied to the cables increased the agglomeration of small imperfections in voids of larger diameters and it was possible to verify the phenomenon of electrical arborescence in the cable with the aluminum core, as well as modifications in the core of stranded cables. Soon after, the Comsol Multiphysics software was used, which uses the Finite Element Method (FEM), solving Maxwell's equations, to better understand the information accessed by the microCT technique that describes electromagnetic phenomena in power cables. The results showed that cables with a greater number of voids have higher electromagnetic field densities when compared to cables without voids in the insulation, showing an increase of 7.5, 10.16, and 9.91 for the copper cables of 25, 35 and 50 mm2, respectively.

Effect of Electric Current Pulse on the Interfacial Reaction Between Molten Steel and SEN During Continuous Casting of Ultra-Low Carbon Steel

Effect of Electric Current Pulse on the Interfacial Reaction Between Molten Steel and SEN During Continuous Casting of Ultra-Low Carbon Steel

Pulse electric current induced interfacial ductile phase on improving the mechanical properties of the Au20Sn/Cu solder joints

Pulse electric current induced interfacial ductile phase on improving the mechanical properties of the Au20Sn/Cu solder joints

Effect of Repetitive High-Density Current Pulses on Plastic Deformation of Copper Wires under Stepwise Loading

High-density electric current pulses increase the plasticity and reduce the yield stress of metals with negligible heat generation. This effect has great potential for the development of energy-saving technologies for processing hard-to-deform metallic materials. Despite the long history of the study of electroplasticity, there is still no consensus on the physical nature of this effect. In this paper, the effect of repetitive pulses applied at the same or gradually increasing tensile stress on the plastic deformation of copper wire is investigated using a home-made experimental setup. The electroplasticity of the wire in the delivery state and after annealing is compared. It is shown that for a constant tensile stress, the incremental plastic deformation of the wire decreases with each successive pulse. This effect is stronger for annealed wires because they have a lower dislocation density and therefore a lower plasticity resource. The Joule heat release in the specimen and the heating due to plastic deformation are evaluated. The results obtained will be used to fit the parameters of the atomistic model being developed to describe the interaction of electron flow with dislocations.

A Case Study: Electrically Assisted Stress Relief Annealing for Cold-Coiled Helical Automotive Springs.

This study experimentally investigated electrically assisted (EA) stress relief annealing for cold-coiled commercial automotive springs. In EA stress relief annealing, the temperature of a spring is rapidly increased to the annealing temperature (400 °C) and is held constant for a specified time using a pulsed electric current. Experimental findings show that the effectiveness of the EA stress relief annealing is superior to that of the conventional stress relief annealing, especially in terms of process time. The present study suggests that EA stress relief annealing, with properly selected process parameters, can effectively substitute for time-consuming conventional stress relief annealing using a furnace for cold-coiled automotive springs.

EFFECT OF OUTPUT VOLTAGE ON AN AZ91D MAGNESIUM ALLOY ROLLED USING AN ELECTRIC PULSE TREATMENT

Magnesium alloys have poor deformation properties at room temperature, and the application of an electric pulse current during deformation can improve the plastic-forming ability. In this study, the electric pulse rolling of AZ91D magnesium alloy specimens has been examined by changing the pulse output voltage. The results demonstrate that the best surface quality and lowest content (8.4 %) of the β-Mg17Al12 phase are achieved at an output voltage of 300 V. EBSD tests have revealed the lowest weave strength on {0002} and {100} at a pulse output voltage of 300 V, as well as the greatest enhancement of twinning. The maximum tensile strength was 165 MPa at an output voltage of 300 V, with a maximum elongation of 4.1 % at an output voltage of 200 V.

Evolution of Laves phase related to tensile properties in cast ATI 718Plus under pulsed electric current

The Laves phase will seriously deteriorate the subsequent hot working and welding performance of cast ATI 718Plus. In traditional homogenization annealing, two-stage treatment is used to prevent the formation of harmful eutectic structures due to the initial melting of the low-melting point Laves phase. This has several obvious disadvantages including high processing temperature, long processing time and complicated operation. Electrical pulsed treatment, as a new efficient, feasible and energy-saving green means, has rapidly achieved the dissolution of Laves phase. The increase in diffusion rate of Nb element in Ni matrix by pulsed electric current is due to the enhancement of defect migration and vacancy defect density, leading to a significant enhancement in the diffusion kinetics and accelerating the dissolution of Laves phase. Laves phase dissolution process under the pulsed electric current is from the aggregated state accompanied by dense needle like η phase to the discrete state accompanied by sparse needle like η phase, finally forming a single long strip and being dissolved into an intermittent state until it disappears. In all, using pulsed electric current instead of traditional heat treatment for annealing cast ingots has the potential to achieve one-step homogenization, completely dissolving the Laves phase while eliminating element segregation.

Fatigue damage recovery and enhanced fatigue limit of austenitic stainless steel using multiple high-density pulsed electric currents

The damage evolution and fatigue life of austenitic stainless steel subjected to high-density pulsed electric currents (HDPECs) were investigated in this study. The change in the fatigue damage evolution owing to the application of HDPECs was evaluated using the cumulative fatigue damage model. Fatigue damage recovery was successfully demonstrated in the low-cycle fatigue and high-cycle fatigue (HCF) regimes. In particular, significant fatigue damage was recovered in the HCF regime when more than six HDPECs were applied. The microstructural features modified by the effect of the HDPEC indicated specific fatigue fracture patterns during fatigue crack initiation, which tended to prefer a transgranular fracture instead of an intergranular fracture. Furthermore, unique fish-eye patterns generated on the subsurface indicated a significant recovery of fatigue damage in the HCF regime owing to the effect of multiple HDPECs. A full fatigue test of R= 0.5 was performed within a fatigue cycle of < 108, resulting in an enhanced fatigue life owing to fatigue damage recovery. Therefore, the application of multiple HDPECs improved the fatigue limit. This study sheds light on the efficiency assessment of the application of HDPECs based on the type of fatigue regime.

Mechanism of Electropulsing Treatment Technology for Flow Stress of Metal Material: A Review

Residual stress is caused by non–uniform deformation caused by non–uniform force, heat and composition, which is of great significance in engineering applications. It is assumed that the residual stress is always the upper limit of the elastic limit, so the reduction of the flow stress will reduce the residual elastic stress. It is particularly important to control the flow stress in metal materials. Compared with traditional methods, the use of electropulsing treatment (EPT) technology stands out due to its energy–efficient, highly effective, straightforward and pollution–free characteristics. However, there are different opinions about the mechanism of reducing flow stress through EPT due to the conflation of the effects from pulsed currents. Herein, a clear correlation is identified between induced stress levels and the application of pulsed electrical current. It was found that the decrease in flow stress is positively correlated with the current density and the duration of electrical contact and current action time. We first systematically and comprehensively summarize the influence mechanisms of EPT on dislocations, phase, textures and recrystallization. An analysis of Joule heating, electron wind effect, and thermal–induced stress within metal frameworks under the influence of pulsed currents was conducted. And the distribution of electric, thermal and stress fields under EPT are discussed in detail based on a finite element simulation (FES). Finally, some new insights into the issues and challenges of flow stress drops caused by EPT are proposed, which is critically important for advancing related mechanism research and the revision of theories and models.

Development of a method for measuring pulse currents of large magnitude

The paper presents the results of a study on the search for correct methods for measuring a high-value current pulse, which will be used to conduct research on the electroplastic effect. The electroplastic effect is the effect of electric current pulses on the plastic flow of metals. Electroplastic metal forming technology is a relatively new metal forming process that is energy efficient, environmentally friendly and versatile. In particular, it can be used to process metals or alloys that are difficult to process using conventional manufacturing processes. For the experimental study of the electroplastic effect, it became necessary to measure pulse currents of large magnitude, not only in amplitude, but also in the shape of the pulse. The pulsed current causes the formation of an alternating electromagnetic field near the conductors, so it can be measured with a Rogovsky current transformer. The results of the work present a schematic electrical diagram and a photograph with the appearance of an experimental installation for the study of the electroplastic effect. The results of measurements of the current value, the voltage drop on the sample and the dependence of the peak voltage values on the sample on the peak current value are shown. After making calculations and renormalising the data for the voltage drop on the sample according to the peak value of the current obtained on the transformer, the authors obtained the desired current values. The error of this method is estimated by calculating the total capacitance of capacitors, which does not exceed 2%.

Research on performance of new separated thermoelectric cooler at different pulse currents

This paper studies the performance of a novel split thermoelectric cooler under the different pulsed electrical currents. The investigation focuses on analyzing changes in the cold side temperature of thermoelectric cooler when subjected to different pulse forms. The three-dimensional heat transfer model established through COMSOL was used to investigate the new thermoelectric cooler. The study focused on analyzing the impacts of pulse amplitude, pulse period, pulse waveform, and heat dissipation conditions on the performance of split cooler. The results show that the cooling temperature of split component can be reduced by about 13 K at constant electrical current compared with the conventional component. The temperature of the separated component can be decreased by an additional 2–5 K through the application of pulsed current. The triangle pulse is the best choice for the split component under continuous pulse when the heat dissipation is insufficient. The split thermoelectric component can work more smoothly by using the slant drop triangle pulse compared with the optimized triangle pulse form. The performance of the split thermoelectric component is optimal under a square pulse when there is adequate heat dissipation.

Room temperature chirality switching and detection in a helimagnetic MnAu2 thin film

Helimagnetic structures, in which the magnetic moments are spirally ordered, host an internal degree of freedom called chirality corresponding to the handedness of the helix. The chirality seems quite robust against disturbances and is therefore promising for next-generation magnetic memory. While the chirality control was recently achieved by the magnetic field sweep with the application of an electric current at low temperature in a conducting helimagnet, problems such as low working temperature and cumbersome control and detection methods have to be solved in practical applications. Here we show chirality switching by electric current pulses at room temperature in a thin-film MnAu2 helimagnetic conductor. Moreover, we have succeeded in detecting the chirality at zero magnetic fields by means of simple transverse resistance measurement utilizing the spin Berry phase in a bilayer device composed of MnAu2 and a spin Hall material Pt. These results may pave the way to helimagnet-based spintronics.

Ultrafast annihilation of irradiation-induced defects using pulsed electric current for damage performance regeneration

As the most important irradiation-induced defects, dislocation loop and copper-rich nanocluster are the major contributors to the embrittlement of the neutron-irradiated reactor pressure vessel steels. In this study, such nano-defects were introduced into the material by 3 MeV Fe ions up to the dose of 1 dpa at high temperature (290 °C) to simulate neutron irradiation. It was found that pulsed electric current can effectively reduce 95 % of irradiation-induced hardening. Correspondingly, the characterization results showed that almost all the dislocation loops disappeared and the quantity of copper-rich nanoclusters also reduced greatly at relatively low temperature (450 °C), and the process took only 20 min. Meanwhile, it was qualitatively proved by positron annihilation spectroscopy that the number of irradiation-induced vacancy-type defects and solute-enriched clusters was significantly decreased after electropulsing. Furthermore, under the pulsed electric field, the rapid annihilation of the dislocation loops due to their accelerated collision with vacancies can remove the nucleation sites of the copper-rich nanoclusters and make them become dispersed, further promoting the nanoclusters that lack nucleation sites dissolving faster. Therefore, this electropulsing treatment provides a practical ‘‘in-situ” performance repair technology to extend the service life of reactor pressure vessel steels by regulating the interaction between vacancies, interstitial atoms and irradiation-induced defects.

Self-assembly of Co/Pt stripes with current-induced domain wall motion towards 3D racetrack devices

Modification of the magnetic properties under the induced strain and curvature is a promising avenue to build three-dimensional magnetic devices, based on the domain wall motion. So far, most of the studies with 3D magnetic structures were performed in the helixes and nanowires, mainly with stationary domain walls. In this study, we demonstrate the impact of 3D geometry, strain and curvature on the current-induced domain wall motion and spin-orbital torque efficiency in the heterostructure, realized via a self-assembly rolling technique on a polymeric platform. We introduce a complete 3D memory unit with write, read and store functionality, all based on the field-free domain wall motion. Additionally, we conducted a comparative analysis between 2D and 3D structures, particularly addressing the influence of heat during the electric current pulse sequences. Finally, we demonstrated a remarkable increase of 30% in spin-torque efficiency in 3D configuration.

Microstructure and Mechanical Properties of Electrically Assisted Brazing Joints of Dissimilar Aluminum and Steel Alloys

The microstructure and mechanical properties of electrically assisted brazing (EA-brazing) joints of aluminum alloy 6061-t6 (AA6061-t6) and S45C steel are experimentally investigated. During the EA-brazing process, an electric current is directly applied to the cylindrical specimen assembly (S45C and AA6061-t6) and fillers of 88% Al and 12% Si (in the middle of the specimen assembly). The temperature of the specimen assembly rises rapidly to the melting point of the filler and remains nearly constant for a period of time using a pulsed electric current. Two types of EA-brazing joints are fabricated, namely Joint-0s (no temperature holding time) and Joint-12s (12 s temperature holding time). The characteristics of the intermetallic compounds (IMCs) formed at the EA-brazing joint interface are analyzed using scanning electron microscopy and energy dispersive spectrometer. Compared to Joint-0s, the Fe-rich IMCs (FeAl) are observed at the interface of Joint-12s due to the 12 s temperature holding time. In addition, the microstructural analysis shows that the thickness of the diffusion layer increases with increasing temperature holding time. The mechanical properties of the EA-brazing joints are evaluated using bending tests. The results of the mechanical test show that the strength of Joint-12s is higher than that of Joint-0s.