Efficient Inverted Perovskite Solar Cells Research Articles

Bimolecular Passivation-Dipole Bridge for Highly Efficient Inverted Perovskite Solar Cells with Low Nonradiative Recombination Loss.

Constructing charge-selective heterointerface with minimized defect state and matched energy level alignment is essential to reduce nonradiative recombination for achieving high-performance perovskite solar cells (PSCs). Herein, a bimolecular passivation-dipole bridge comprised of sodium phenylmethanesulfonate (SPM) and 2-phenylethylammonium iodide (PEAI) is carefully developed to regulate perovskite heterointerface. SPM passivates defect states and upshifts Fermi level (EF) of perovskite surface, and subsequent PEAI further induces additional negative dipole and causes the surface EF of perovskite pinning to negative polaron transport state of electron transport layer PCBM, which significantly promotes electron extraction at the perovskite electron-selective contact. These advantages are confirmed by a remarkably improved efficiency from 21.74% for control to 25.12% for treated PSC with excellent stability. Moreover, corresponding nonradiative recombination loss impressively diminishes from 123 to 70 meV, and charge transport-induced fill factor loss is only 3.00%. This work provides a promising approach via passivation-energetic synergy for engineering perovskite heterointerface toward highly efficient and stable PSCs.

Efficient and stable inverted perovskite solar cells enabled by homogenized PCBM with enhanced electron transport

Fullerene derivatives are extensively employed in inverted perovskite solar cells due to their excellent electron extraction capabilities. However, [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) agglomerates easily in solution and exhibits a relatively low ionization barrier, increasing charge recombination losses and charge accumulation in the interface. Here, tetramethylthiuram disulfide (TMDS) is introduced into the PCBM solution to induce the formation of reducing sulfur radicals through UV light irradiation, allowing for n doping of the PCBM material. The resulting modified PCBM layer exhibits enhanced conductivity and electron mobility, significantly suppressing charge recombination. As a result, the resulting devices incorporating TMDS achieve a champion efficiency of 26.10% (certified 25.39%) and 24.06% at a larger area (1.0 cm2) with negligible hysteresis. More importantly, the optimized devices retain 95% and 90% of their initial efficiency after 1090 h under damp heat testing (85 °C and 85% relative humidity) and after 1271 h under maximum power point-tracking conditions, respectively.

Molecularly tailored bifunctional nano-overlayers for efficient and stable inverted perovskite solar cells

Triple cation perovskite solar cells (PSCs) have made remarkable progress in power conversion efficiency (PCE), which is also related to the interface regulation layers between the active layer and electron transport layer (ETL). The ionic nature of the perovskite lattice has enabled approaches to passivate molecular defects through the interaction of functional groups. Herein, a passivator OXD-7 is introduced as a modified layer to passivate surface defects and accelerate electron transfer. It has been observed that OXD-7 can alleviate the micro-strain of the perovskite thin films through intermolecular bonding, which suppresses the iodide vacancy on the perovskite surface. Additionally, the OXD-7 reduces the surface energy of the perovskite films and inhibits the formation of δ-FAPbI3 on the surface of perovskite film. Consequently, the resulting devices demonstrate improved fill factor and device stability. Under optimal fabrication conditions, triple cation mixed perovskite solar cells with an inverted structure achieve a PCE of 23.83%.

Enhanced Buried Interface Engineering for Efficient Inverted Perovskite Solar Cells Fabricated via Vapor-Solid Reaction.

Vapor-deposited inverted perovskite solar cells utilizing self-assembled monolayer (SAM) as hole transport material have gained significant attention for their high efficiencies and compatibility with silicon/perovskite monolithic tandem devices. However, as a small molecule, the SAM layer suffers low thermal tolerance in comparison with other metal oxide or polymers, rendering poor efficiency in solar device with high-temperature (> 160°C) fabricating procedures. In this study, a dual modification approach involving AlOx and F-doped phenyltrimethylammonium bromide (F-PTABr) layers is introduced to enhance the buried interface. The AlOx dielectric layer improves the interface contact and prevents the upward diffusion of SAM molecules during the vapor-solid reaction at 170°C, while the F-PTABr layer regulates crystal growth and reduces the interfacial defects. As a result, the AlOx/F-PTABr-treated perovskite film exhibits a homogeneous, pinhole-free morphology with improved crystal quality compared to the control films. This leads to a champion power conversion efficiency of 21.53% for the inverted perovskite solar cells. Moreover, the encapsulated devices maintained 90% of the initial efficiency after 600h of ageing at 85°C in air, demonstrating promising potential for silicon/perovskite tandem application.

Synergistic anti-solvent engineering with piperizium salts for highly efficient inverted perovskite solar cells exceeding 25 %

Trap-assisted non-radiative recombination in the perovskite (PVK) film is a primary limitation in further enhancing the performance of inverted perovskite solar cells (PSCs). Herein, an effective anti-solvent additive strategy is proposed, employing 1-(2-Methoxyphenyl)piperazine hydrochloride (2MPCl) as a multifunctional anti-solvent additive to passivate defects in PVK. The introduction of 2MPCl effectively passivate Pb2+ and halide vacancies through ion bonds and hydrogen bonds, thereby obtaining high-quality PVK films. Besides, the multifunctional 2MPCl can effectively modulate the energy level structure of PVK, resulting in a more n-type PVK surface, thereby facilitating electron transfer between PVK and PCBM. Consequently, the optimization of energy levels and suppression of trap-assisted recombination elevate the efficiency of devices with 2MPCl to 25.02 %, with significantly enhanced stability compared to control devices. This novel anti-solvent additive strategy aims to address the challenge of trap-assisted non-radiative recombination in PVK film, which is important for enhancing the performance of inverted PSCs.

Enhancement the performance of MAPbI3 perovskite solar cells via germanium sulfide doping

In this study, we successfully doped Germanium sulfide (GeS) particles in methylammonium lead triiodide (CH3NH3PbI3) films to create highly efficient inverted perovskite solar cells (PSC). Various characterization methodologies were employed to examine the impact of GeS on the morphological, structural, and compositional properties of the CH3NH3PbI3 perovskite. The X-ray diffraction and Raman spectroscopy analyses of the synthesized products demonstrated that the crystallinity was enhanced, and tetragonal perovskite structures were generated without any impurities when GeS was used at a high concentration. The surface morphology results indicated that the CH3NH3PbI3 perovskite possessed thin coatings with compact, uniform, and smooth surfaces, with large grain size. The production of a high-quality CH3NH3PbI3 film from the CH3NH3PbI3: GeS phase results in improved carrier lifetime, decreased charge-trap density, and nonradiative recombination of the perovskite films. Band gap was observed to be correlated with grain size and crystallinity, which was accompanied by an increase in GeS concentration. We attained a maximum conversion efficiency of 17.46 % by fabricating solar cells with the following structure: soda-lime glass FTO/TiO2/CH3NH3PbI3: GeS/spiro-oMeTAD/Au. Based on our findings, we believe that the doping of GeS is a promising method for improving the properties of perovskite solar cells that are based on CH3NH3PbI3 thin films.

Magnetron sputtered nickel oxide with suppressed interfacial defect states for efficient inverted perovskite solar cells

Widely used spin-coated nickle oxide (NiOx) based perovskite solar cells often suffer from severe interfacial reactions between the NiOx and adjacent perovskite layers due to surface defect states, which inherently impair device performance in a long-term view, even with surface molecule passivation. In this study, we developed high-quality magnetron-sputtered NiOx thin films through detailed process optimization, and compared systematically sputtered and spin-coated NiOx thin film surfaces from materials to devices. These sputtered NiOx films exhibit improved crystallinity, smoother surfaces, and significantly reduced Ni3+ or Ni vacancies compared to their spin-coated counterparts. Consequently, the interface between the perovskite and sputtered NiOx film shows a substantially reduced density of defect states. Perovskite solar cells (PSCs) fabricated with our optimally sputtered NiOx films achieved a high power conversion efficiency (PCE) of up to 19.93% and demonstrated enhanced stability, maintaining 86.2% efficiency during 500 h of maximum power point tracking under one standard sun illumination. Moreover, with the surface modification using (4-(2,7-dibromo-9,9-dimethylacridin-10(9H)-yl)butyl)phosphonic acid (DMAcPA), the device PCE was further promoted to 23.07%, which is the highest value reported for sputtered NiOx based PSCs so far.

Enhancing Hole Transport Uniformity for Efficient Inverted Perovskite Solar Cells through Optimizing Buried Interface Contacts and Suppressing Interface Recombination.

[4-(3,6-dimethyl-9H-carbazol-9yl)butyl]phosphonic acid (Me-4PACz) self-assembly material has been recognized as a highly effective approach for mitigating nickel oxide (NiOx) surface-related challenges in inverted perovskite solar cells (IPSCs). However, its uneven film generation and failure to effectively passivate the buried interface defects limit the device's performance improvement potential. Herein, p-xylylenediphosphonic acid (p-XPA) containing bilateral phosphate groups (-PO3H2) is introduced as an interface layer between the NiOx/Me-4PACz and the perovskite layer. P-XPA can flatten the surface of hole transport layer and optimize interface contact. Meanwhile, p-XPA achieves better energy level alignment and promotes interfacial hole transport. In addition, the bilateral -PO3H2 of p-XPA can chelate with Pb2+ and form hydrogen bond with FA+ (formamidinium cation), thereby suppressing buried interface non-radiative recombination loss. Consequently, the IPSC with p-XPA buried interface modification achieves champion power conversion efficiency of 25.87% (certified at 25.45%) at laboratory scale (0.0448 cm2). The encapsulated target device exhibits better operational stability. Even after 1100 hours of maximum power point tracking at 50 ℃, its efficiency remains at an impressive 82.7% of the initial efficiency. Molecules featuring bilateral passivation groups optimize interfacial contact and inhibit interfacial recombination, providing an effective approach to enhancing the stability and efficiency of devices.

Enhancing Hole Transport Uniformity for Efficient Inverted Perovskite Solar Cells through Optimizing Buried Interface Contacts and Suppressing Interface Recombination

[4‐(3,6‐dimethyl‐9H‐carbazol‐9yl)butyl]phosphonic acid (Me‐4PACz) self‐assembly material has been recognized as a highly effective approach for mitigating nickel oxide (NiOx) surface‐related challenges in inverted perovskite solar cells (IPSCs). However, its uneven film generation and failure to effectively passivate the buried interface defects limit the device's performance improvement potential. Herein, p‐xylylenediphosphonic acid (p‐XPA) containing bilateral phosphate groups (‐PO3H2) is introduced as an interface layer between the NiOx/Me‐4PACz and the perovskite layer. P‐XPA can flatten the surface of hole transport layer and optimize interface contact. Meanwhile, p‐XPA achieves better energy level alignment and promotes interfacial hole transport. In addition, the bilateral ‐PO3H2 of p‐XPA can chelate with Pb2+ and form hydrogen bond with FA+ (formamidinium cation), thereby suppressing buried interface non‐radiative recombination loss. Consequently, the IPSC with p‐XPA buried interface modification achieves champion power conversion efficiency of 25.87% (certified at 25.45%) at laboratory scale (0.0448 cm2). The encapsulated target device exhibits better operational stability. Even after 1100 hours of maximum power point tracking at 50 ℃, its efficiency remains at an impressive 82.7% of the initial efficiency. Molecules featuring bilateral passivation groups optimize interfacial contact and inhibit interfacial recombination, providing an effective approach to enhancing the stability and efficiency of devices.

Role of self-assembled molecules’ anchoring groups for surface defect passivation and dipole modulation in inverted perovskite solar cells

Abstract Inverted perovskite solar cells have gained prominence in industrial advancement due to their easy fabrication, low hysteresis effects, and high stability. Despite these advantages, their efficiency is currently limited by excessive defects and poor carrier transport at the perovskite–electrode interface, particularly at the buried interface between the perovskite and transparent conductive oxide (TCO). Recent efforts in the perovskite community have focused on designing novel self-assembled molecules (SAMs) to improve the quality of the buried interface. However, a notable gap remains in understanding the regulation of atomic-scale interfacial properties of SAMs between the perovskite and TCO interfaces. This understanding is crucial, particularly in terms of identifying chemically active anchoring groups. In this study, we used the star SAM ([2-(9H-carbazol-9-yl)ethyl] phosphonic acid) as the base structure to investigate the defect passivation effects of eight common anchoring groups at the perovskite–TCO interface. Our findings indicate that the phosphonic and boric acid groups exhibit notable advantages. These groups fulfill three key criteria: they provide the greatest potential for defect passivation, exhibit stable adsorption with defects, and exert significant regulatory effects on interface dipoles. Ionized anchoring groups exhibit enhanced passivation capabilities for defect energy levels due to their superior Lewis base properties, which effectively neutralize local charges near defects. Among various defect types, iodine vacancies are the easiest to passivate, whereas iodine-substituted lead defects are the most challenging to passivate. Our study provides comprehensive theoretical insights and inspiration for the design of anchoring groups in SAMs, contributing to the ongoing development of more efficient inverted perovskite solar cells.

Cyclic Multi‐Site Chelation for Efficient and Stable Inverted Perovskite Solar Cells

Trap‐assisted non‐radiative recombination losses and moisture‐induced degradation significantly impede the development of highly efficient and stable inverted (p‐i‐n) perovskite solar cells (PSCs), which require high‐quality perovskite bulk. In this research, we mitigate these challenges by integrating thermally stable perovskite layers with Lewis base covalent organic frameworks (COFs). The ordered pore structure and surface binding groups of COFs facilitate cyclic, multi‐site chelation with undercoordinated lead ions, enhancing the perovskite quality across both its bulk and grain boundaries. This process not only reduces defects but also promotes improved energy alignment through n‐type doping at the surface. The inclusion of COF dopants in p‐i‐n devices achieves power conversion efficiencies (PCEs) of 25.64% (certified 24.94%) for a 0.0748‐cm2 device and 23.49% for a 1‐cm2 device. Remarkably, these devices retain 81% of their initial PCE after 978 hours of accelerated aging at 85˚C, demonstrating remarkable durability. Additionally, COF‐doped devices demonstrate excellent stability under illumination and in moist conditions, even without encapsulation.

Surface passivation enables efficient and stable inverted perovskite solar cells by 6-(Trifluoromethyl)pyridine-3-amidinehydrochloride

The inverted p-i-n PSCs are gradually gaining more attention since they are generally more stable and can employ low-cost transport materials. However, the interfaces between the perovskite and the charge transport layers contribute to major power conversion efficiency (PCE) loss and instability. Here, we use a material of 6-(Trifluoromethyl)pyridine-3-amidinehydrochloride (CF3-PyFACl) to molecularly engineer the interface between the perovskite and electron transport layer. The interface modification results in suppressed nonradiative recombination, and improved interfacial contact. A PCE of 23.17 % is demonstrated, with open-circuit voltage (Voc) and fill factor (FF) of 1.169 V and 84.1 %, respectively. The unencapsulated device retains >80 % of the initial performance after 400 h continuous light soaking.

Molecule-triggered strain regulation and interfacial passivation for efficient inverted perovskite solar cells

Molecule-triggered strain regulation and interfacial passivation for efficient inverted perovskite solar cells

Ambient Air Processed Inverted Inorganic Perovskite Solar Cells with over 21 % Efficiency Enabled by Multifunctional Ethacridine Lactate

AbstractAll‐inorganic cesium lead triiodide perovskites (CsPbI3) have attracted increasing attention due to their good thermal stability, remarkable optoelectronic properties, and adaptability in tandem solar cells. However, N2‐filled glovebox is generally required to strictly control the humidity during film fabrication due to the moisture‐induced black‐to‐yellow phase transition, which remains a great hinderance for further commercialization. Herein, we report an effective approach via incorporating multifunctional ethacridine lactate (EAL) to mitigate moisture invasion and enable the fabrication of efficient inverted (p‐i‐n) CsPbI3 perovskite solar cells (PSCs) under ambient condition. It is revealed that the lactate anions accelerate the crystallization of CsPbI3, shortening the exposure time to moisture during film fabrication. Meanwhile, the conjugated backbone and multiple functional groups in the ethacridine cations can interact with I− and Pb2+ to reduce the undesired defects, stabilize the perovskite structure and facilitate the charge transport in the film. Moreover, EAL incorporation also leads to better energy alignment, thus favoring charge extraction at both upper and bottom interfaces. Consequently, the device efficiency and stability are enormously enhanced, with the champion efficiency reaching 21.08 %. This even surpasses the highest value reported for the devices fabricated in glovebox, representing a record efficiency of inverted all‐inorganic PSCs.

Ambient Air Processed Inverted Inorganic Perovskite Solar Cells with over 21 % Efficiency Enabled by Multifunctional Ethacridine Lactate.

All-inorganic cesium lead triiodide perovskites (CsPbI3) have attracted increasing attention due to their good thermal stability, remarkable optoelectronic properties, and adaptability in tandem solar cells. However, N2-filled glovebox is generally required to strictly control the humidity during film fabrication due to the moisture-induced black-to-yellow phase transition, which remains a great hinderance for further commercialization. Herein, we report an effective approach via incorporating multifunctional ethacridine lactate (EAL) to mitigate moisture invasion and enable the fabrication of efficient inverted (p-i-n) CsPbI3 perovskite solar cells (PSCs) under ambient condition. It is revealed that the lactate anions accelerate the crystallization of CsPbI3, shortening the exposure time to moisture during film fabrication. Meanwhile, the conjugated backbone and multiple functional groups in the ethacridine cations can interact with I- and Pb2+ to reduce the undesired defects, stabilize the perovskite structure and facilitate the charge transport in the film. Moreover, EAL incorporation also leads to better energy alignment, thus favoring charge extraction at both upper and bottom interfaces. Consequently, the device efficiency and stability are enormously enhanced, with the champion efficiency reaching 21.08 %. This even surpasses the highest value reported for the devices fabricated in glovebox, representing a record efficiency of inverted all-inorganic PSCs.

Repairing Interfacial Defects in Self-Assembled Monolayers for High-Efficiency Perovskite Solar Cells and Organic Photovoltaics through the SAM@Pseudo-Planar Monolayer Strategy.

Lately, carbazole-based self-assembled monolayers (SAMs) are widely employed as effective hole-selective layers (HSLs) in inverted perovskite solar cells (PSCs). Nevertheless, these SAMs tend to aggregate in solvents due to their amphiphilic nature, hindering the formation of a monolayer on the ITO substrate and impeding effective passivation of deep defects in the perovskites. In this study, a series of new SAMs including DPA-B-PY, CBZ-B-PY, POZ-B-PY, POZ-PY, POZ-T-PY, and POZ-BT-PY are synthesized, which are employed as interfacial repairers and coated atop CNph SAM to form a robust CNph SAM@pseudo-planar monolayer as HSL in efficient inverted PSCs. The CNph SAM@pseudo-planar monolayer strategy enables a well-aligned interface with perovskites, synergistically promoting perovskite crystal growth, improving charge extraction/transport, and minimizing nonradiative interfacial recombination loss. As a result, the POZ-BT-PY-modified PSC realizes an impressively enhanced solar efficiency of up to 24.45% together with a fill factor of 82.63%. Furthermore, a wide bandgap PSC achieving over 19% efficiency. Upon treatment with the CNph SAM@pseudo-planar monolayer, also demonstrates a non-fullerene organic photovoltaics (OPVs) based on the PM6:BTP-eC9 blend, which achieves an efficiency of 17.07%. Importantly, these modified PSCs and OPVs all show remarkably improved stability under various testing conditions compared to their control counterparts.

Effective surface treatment for efficient and stable inverted inorganic CsPbI2Br perovskite solar cells

The interest in all-inorganic perovskite solar cells (PSCs) featuring a p-i-n structure is on the rise, attributed to their superior heat resistance and adaptability with tandem cell methods. However, their progress has been far from the regular structure owing to the comparatively low open circuit voltage (Voc). This research employs phenylethylammonium iodide, incorporating various side groups, as passivators to tackle the previously mentioned problems and investigate their effects on passivation. It is found that a reduction of trap-state density in perovskite film was accomplished due to the PEAI effective passivation effect by establishing coordination with the under-coordinated Pb2+ ions. Furthermore, there was an enhancement in the alignment of energy levels at the CsPbI2Br perovskite/PCBM junction, resulting in better charge extraction from the CsPbI2Br layer to the charge transport layer. As a result, an improved champion efficiency of 14.26 % with a Voc of 1.11 V, Jsc of 16.21 mA/cm2, and FF of 79.28 % was yielded for the PEAI treatment inverted CsPbI2Br device, compared with the 12.15 % efficiency of the control device. Superior device stability was exhibited for the optimal PEAI-treated devices without encapsulation. This research validates the significance of a side group on a surface passivation molecule to effectively passivate defects and optimize energy levels, especially for boosting Voc.

Glycol Monomethyl Ether-Substituted Carbazolyl Hole-Transporting Material for Stable Inverted Perovskite Solar Cells with Efficiency of 25.52 .

Organic self-assembled molecules (OSAMs) based hole-transporting materials play a pivotal role in achieving highly efficient and stable inverted perovskite solar cells (IPSCs). However, the reported carbazol-based OSAMs have serious drawbacks, such as poor wettability for perovskite solution spreading due to the nonpolar surface, worse matched energy arrangement with perovskite, and limited molecular species, which greatly limit the device performance. To address above problems, a novel OSAM [4-(3,6-glycol monomethyl ether-9H-carbazol-9-yl) butyl]phosphonic acid (GM-4PACz) was synthesized as hole-transporting material by introducing glycol monomethyl ether (GM) side chains at carbazolyl unit. GM groups enhance the surface energy of Indium Tin Oxide (ITO)/SAM substrate to facilitate the nucleation and growth of up perovskite film, suppress cation defects, release the residual stress at SAM/perovskite interface, and evaluate energy level for matching with perovskite. Consequently, the GM-4PACz based IPSC achieves a champion PCE of 25.52 %, a respectable open-circuit voltage (VOC) of 1.21 V, a high stability, possessing 93.29 % and 91.75 % of their initial efficiency after aging in air for 2000 h or tracking at maximum power point for 1000 h, respectively.

Glycol Monomethyl Ether‐Substituted Carbazolyl Hole‐Transporting Material for Stable Inverted Perovskite Solar Cells with Efficiency of 25.52 %

AbstractOrganic self‐assembled molecules (OSAMs) based hole‐transporting materials play a pivotal role in achieving highly efficient and stable inverted perovskite solar cells (IPSCs). However, the reported carbazol‐based OSAMs have serious drawbacks, such as poor wettability for perovskite solution spreading due to the nonpolar surface, worse matched energy arrangement with perovskite, and limited molecular species, which greatly limit the device performance. To address above problems, a novel OSAM [4‐(3,6‐glycol monomethyl ether‐9H‐carbazol‐9‐yl) butyl]phosphonic acid (GM‐4PACz) was synthesized as hole‐transporting material by introducing glycol monomethyl ether (GM) side chains at carbazolyl unit. GM groups enhance the surface energy of Indium Tin Oxide (ITO)/SAM substrate to facilitate the nucleation and growth of up perovskite film, suppress cation defects, release the residual stress at SAM/perovskite interface, and evaluate energy level for matching with perovskite. Consequently, the GM‐4PACz based IPSC achieves a champion PCE of 25.52 %, a respectable open‐circuit voltage (VOC) of 1.21 V, a high stability, possessing 93.29 % and 91.75 % of their initial efficiency after aging in air for 2000 h or tracking at maximum power point for 1000 h, respectively.

Device modeling of high performance and eco-friendly FAMASnI3\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\ ext {FAMASnI}}_{3}$$\\end{document} based perovskite solar cell

Developing environmentally friendly and highly efficient inverted perovskite solar cells (PSCs) encounters significant challenges, specifically the potential toxicity and degradation of thin films in hybrid organic-inorganic photovoltaics (PV). We employed theoretical design strategies that produce hysteresis-reduced, efficient, and stable PSCs based on composition and interface engineering. The devices include a mixed-organic-cation perovskite formamidinium methylammonium tin iodide (FAMASnI3\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\ ext {FAMASnI}}_{3}$$\\end{document}) as an absorber layer and zinc oxide (ZnO) together with a passivation film phenyl-C61-butyric acid methyl ester (PC61BM\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\ ext {PC}}_{61}\ ext {BM}$$\\end{document}) as a double-electron transport layer (DETL). Furthermore, a nickel oxide (NiO) layer and a trap-free junction copper iodide (CuI) are used as a double-hole transport layer (DHTL). The optoelectronic characterization measurements were carried out to understand the physical mechanisms that govern the operation of the devices. The high power conversion efficiencies (PCEs) of 24.27% and 23.50% were achieved in 1D and 2D simulations, respectively. This study illustrates that composition and interface engineering enable eco-friendly perovskite solar cells, improving performance and advancing clean energy.