Effects Of Particle Surface Charge Research Articles

Multiscale Modelling of Nanoparticle Distribution in a Realistic Tumour Geometry Following Local Injection

Radiosensitizers have proven to be an effective method of improving radiotherapy outcomes, with the distribution of particles being a crucial element to delivering optimal treatment outcomes due to the short range of effect of these particles. Here we present a computational model for the transport of nanoparticles within the tumour, whereby the fluid velocity and particle deposition are obtained and used as input into the convection-diffusion equation to calculate the spatio-temporal concentration of the nanoparticles. The effect of particle surface charge and injection locations on the distribution of nanoparticle concentration within the interstitial fluid and deposited onto cell surfaces is assessed. The computational results demonstrate that negatively charged particles can achieve a more uniform distribution throughout the tumour as compared to uncharged or positively charged particles, with particle volume within the fluid being 100% of tumour volume and deposited particle volume 44.5%. In addition, varying the injection location from the end to the middle of the tumour caused a reduction in particle volume of almost 20% for negatively charged particles. In conclusion, radiosensitizing particles should be negatively charged to maximise their spread and penetration within the tumour. Choosing an appropriate injection location can further improve the distribution of these particles.

Investigation of the Effect of Particle Surface Charge and Dispersion Stability on Latex Behavior in Cement Using Non-Ionic and Traditional Latexes.

In this work, a novel total non-ionic polystyrene-polyurethane (PS-PU) composite latex was synthesized with polymerizable polyethylene glycol ether. Contrary to traditional styrene-butyl acrylate latex (St-BA), PS-PU has a smaller size and superior dispersion stability, and it is stable in saturated Ca(OH)2 even after 72 h. In fresh-mixed mortars, PS-PU showed a little adverse effect on workability and insignificant air entrainment, with little defoamer consumption. The retardation effect of PS-PU is also much milder than traditional St-BA. As for strength, PS-PU showed a less adverse effect on early and late age compressive strength, but its effect on flexural strength is not as pronounced as St-BA at high dosages (4% and 6%). The different behavior in cementitious materials between PS-PU and St-BA can be reasoned from their different adsorption behavior and surface charge properties, as the results from characterizations suggest. The non-ionic nature of PS-PU made it less prone to destabilization and adsorption, which turned out as the aforementioned behavior in cementitious systems. The difference can further be ascribed to the difference in their polymeric structure and properties.

Assessment of Sub-Micron Particles by Exploiting Charge Differences with Dielectrophoresis.

The analysis, separation, and enrichment of submicron particles are critical steps in many applications, ranging from bio-sensing to disease diagnostics. Microfluidic electrokinetic techniques, such as dielectrophoresis (DEP) have proved to be excellent platforms for assessment of submicron particles. DEP is the motion of polarizable particles under the presence of a non-uniform electric field. In this work, the polarization and dielectrophoretic behavior of polystyrene particles with diameters ranging for 100 nm to 1 μm were studied employing microchannels for insulator based DEP (iDEP) and low frequency (<1000 Hz) AC and DC electric potentials. In particular, the effects of particle surface charge, in terms of magnitude and type of functionalization, were examined. It was found that the magnitude of particle surface charge has a significant impact on the polarization and dielectrophoretic response of the particles, allowing for successful particle assessment. Traditionally, charge differences are exploited employing electrophoretic techniques and particle separation is achieved by differential migration. The present study demonstrates that differences in the particle’s surface charge can also be exploited by means of iDEP; and that distinct types of nanoparticles can be identified by their polarization and dielectrophoretic behavior. These findings open the possibility for iDEP to be employed as a technique for the analysis of submicron biological particles, where subtle differences in surface charge could allow for rapid particle identification and separation.

Effect of particle surface charge on drug uptake

AbstractIn this paper, it aims to build the relationship of statically electric interaction between the surface charge of a particle drug and cellular uptake. The statically electric theory is applied to study the change of wetting between the drug particle and the cell, a factor that enhanced uptake of cells induced by particle’s surface charge is introduced, then it is formulated according to Kelvin theory for dissolving of solid particle in liquid. It is found that the change of contact angle between the surface charged particle drug and the cell can be detected if the Zeta potential reaches to 6 mV in water like solution, an increase of about 11.1% for the uptake could be obtained for a polymer particle with molar mass

Effects of Particle Surface Charge, Species, Concentration, and Dispersion Method on the Thermal Conductivity of Nanofluids

The purpose of this experimental study is to evaluate the effects of particle species, surface charge, concentration, preparation technique, and base fluid on thermal transport capability of nanoparticle suspensions (nanofluids). The surface charge was varied by changing the pH value of the fluids. The alumina ([Formula: see text]) and copper oxide (CuO) nanoparticles were dispersed in deionized (DI) water and ethylene glycol (EG), respectively. The nanofluids were prepared using both bath-type and probe sonicator under different power inputs. The experimental results were compared with the available experimental data as well as the predicted values obtained from Maxwell effective medium theory. It was found that ethylene glycol is more suitable for nanofluids applications than DI water in terms of thermal conductivity improvement and stability of nanofluids. Surface charge can effectively improve the dispersion of nanoparticles by reducing the (aggregated) particle size in base fluids. A nanofluid with high surface charge (low pH) has a higher thermal conductivity for a similar particle concentration. The sonication also has a significant impact on thermal conductivity enhancement. All these results suggest that the key to the improvement of thermal conductivity of nanofluids is a uniform and stable dispersion of nanoscale particles in a fluid.

Functionally charged polystyrene particles activate immortalized mouse microglia (BV2): cellular and genomic response

The effect of particle surface charge on the biological activation of immortalized mouse microglia (BV2) was examined. Same size (∼850–950 nm) spherical polystyrene microparticles (SPM) with net negative (carboxyl, COOH-) or positive (dimethyl amino, CH3)2-N- zeta potentials were exposed to BV2 microglia (5–20 µl/ml). Both stimulated an oxidative burst, increased Caspase 3/7 activity and caused inflammatory cytokine release. Ultrastructure indicated that SPM particles were phagocytosed as single particles but formed large intra-cellular 4–6 µm agglomerates. Microarray analysis indicated that negatively charged SPM-COOH- affected approximately 146 genes while the positively charged SPM-(CH3)2-N- affected approximately 2580 genes. Only 30 genes were significantly affected in common. Of the 48 genes associated with oxidative stress pathways, 33 genes were coordinately down-regulated by SPM-(CH3)2-N- and up-regulated by SPM-COOH- exposure. Together, these data indicate that functionally charged, inert submicron-size particles differentially activate BV2 microglia along oxidative stress and inflammatory pathways.

Is Latex Surface Charge an Important Parameter for Foam Stabilization?

We describe the facile production of highly stable foams stabilized solely by cationic polystyrene latex particles. Three model polystyrene latexes were synthesized using either a cationic 2,2'-azobis(2-diisobutyramidine) dihydrochloride (AIBA) or an anionic ammonium persulfate (APS) radical initiator: a 724 +/- 81 nm charge-stabilized cationic polystyrene latex [AIBA-PS], an 800 +/- 138 nm sterically stabilized cationic latex prepared using a poly(ethylene glycol) monomethacrylate macromonomer [PEGMA-AIBA-PS], and a 904 +/- 131 nm charge-stabilized anionic polystyrene latex [APS-PS], respectively. The effect of particle surface charge, latex concentration, and solution pH on foam stability was studied in detail. The PEGMA-AIBA-PS latex proved to be the best foam stabilizer even at relatively low latex concentrations (3.0 wt %), with long-term foam stabilities being obtained after drying. The AIBA-PS latex also produced stable foams, albeit only at higher latex concentrations. However, the APS-PS latex proved to be an ineffective foam stabilizer. This is believed to be primarily due to the anionic surface character of this latter latex, which prevents its adsorption at the anionic air-water interface. This hypothesis is supported by the observation that the AIBA-PS latex no longer acts as an effective foam stabilizer above its isoelectric point (pH 7.04). Scanning electron microscopy studies revealed the formation of well-defined latex bilayers within dried foams, which indicates that the wet air bubbles are stabilized by latex monolayers prior to drying. However, little or no long-range ordering of the latex particles was observed on the surface of the bubbles, which is presumably related to the latex polydispersity.

Sol−Gel Reaction in Acrylic Polymer Emulsions: The Effect of Particle Surface Charge

Acrylic polymer-silica hybrid emulsions were synthesized from both anionic and cationic polymer emulsions by simple post-addition of tetraethoxysilane as a silica precursor. Solvent resistance of the films from the hybrid emulsions and the zeta-potential of the hybrid emulsions suggested the different forms of silica components in each hybrid emulsion. Thermal gravimetric analysis, 29Si NMR measurements, and transmission electron microscope observations revealed that the hybrid emulsion from the anionic polymer emulsion was a mixture of anionic polymer particles and homogeneously dissolved silicate oligomer-polymer. On the contrary, the hybrid emulsion from cationic polymer emulsion consisted of polymer core-silica shell particles. The electrostatic interaction between the cationic polymer particle surface and the silicate would be responsible for the accumulation of the silicate onto the particle surface, leading to the silica shell layer formation. The sol-gel condensation reaction of silicate in the acidic emulsion phase was revealed to be controllable by the surface charge of the coexisting particles.