Effects Of Dynamic Vulcanization Research Articles

Effects of dynamic vulcanization on the kinetics of isothermal crystallization in a miscible polymeric blend

Is it possible to determine the state of phase separation using the free energy of folding parameter?

Effects of dynamic vulcanization on tensile, morphological, and swelling properties of poly(vinyl chloride) (PVC)/epoxidized natural rubber (ENR)/(Kenaf core powder) composites

The effects of dynamic vulcanization on properties of poly(vinyl chloride) (PVC)/epoxidized natural rubber (ENR)/(kenaf core powder) composite were studied. Tensile properties indicated that the strength, elongation at break, and Young's modulus of the composites exhibited an increase for samples with dynamic vulcanization. Morphological analysis using scanning electron microscopy showed the interaction between ENR and PVC. There was no bonding between kenaf core powder and the PVC/ENR matrix owing to the different polarity of both components. Filler agglomerates increased, which leads to an increase of filler‐filler interaction and poor dispersion. Furthermore, swelling index indicated that the composite with dynamic vulcanization shows lower absorption of tolune compared with composites without dynamic vulcanization. J. VINYL ADDIT. TECHNOL., 22:206–212, 2016. © 2014 Society of Plastics Engineers

The Effects of Dynamic Vulcanization in Virgin Polyethylene (vPE)/Recycled Polyethylene (rPE)/Ethylene Propylene Diene Terpolymer (EPDM) Blends: Thermal Properties and Swelling Behaviour

The effects of dynamic vulcanization on the thermal properties and swelling behaviour of vPE/rPE/EPDM blends were studied. The discarded polyethylene used in the study was obtained from local wire insulation industry. The thermal properties and swelling behaviour of the blends were analyzed. Results show that increasing of sulfur loading had improved the thermal stability of the blends. The swelling percentage and swelling index of vPE/rPE/EPDM blends also decreased, inversely proportional to the increasing of sulfur loading. Thus, the increased incorporation of sulfur loading had improved the chemical and oil resistance of the blends.

Effects of dynamic vulcanization on the physical, mechanical, and morphological properties of high‐density polyethylene/(natural rubber)/(thermoplastic tapioca starch) blends

AbstractBlending of high density polyethylene (HDPE), natural rubber (NR), and thermoplastic tapioca starch (TPS) have been studied. Two series of samples having 5–30 wt% of TPS were prepared: (a) unvulcanized blends (control) and (b) dynamically vulcanized HDPE/NR/TPS blends. The composition of the HDPE/NR was constant and fixed at a blend ratio of 70/30. Morphology studies by SEM showed that the TPS particles were homogeneously dispersed and well‐embedded in vulcanized HDPE/NR matrix. The SEM micrographs showed agreement with the tensile strength and elongation at break values. Tensile strength improved significanly when the HDPE/NR/TPS blends were vulcanized by using sulfur curative system. The enhancement in tensile properties is attributed to the crosslinking reaction within the NR phase. J. VINYL ADDIT. TECHNOL., 18:192–197, 2012. © 2012 Society of Plastics Engineers

Physical properties of polyamide 6/H‐NBR blends and the effects of dynamic vulcanization on them

AbstractPolyamide 6 (PA 6) and hydrogenated nitrile rubber (H‐NBR) were blended with various blend ratios in a brabender plasticoder at 240°C/100 rpm. The processing characteristics with a mixing torque of the blends were investigated. The effect of the blend ratio on physical properties such as tensile strength, Young's modulus, elongation at break, permanent set, hardness, and swelling behavior of blends was analyzed. Most mechanical properties were found to decrease with an addition of H‐NBR. The morphology of the blends was observed, and the results show a two phase system where the component with high proportions exists as a continuous phase. A cocontinuous phase was observed in blend ratios of 50/50 and 40/60. Dynamic mechanical properties were observed to study a viscoelastic property of the blends. In addition, the effect of dynamic vulcanization with peroxide on physical properties was studied, and the influence of peroxide on PA 6 was also examined. It was found that the peroxide can have an effect on PA 6 as well as act as a crosslinker to H‐NBR. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011

Melt rheology of HDPE/EVA blends: The effects of blend ratio, compatibilization, and dynamic vulcanization

The melt rheological behavior of high-density polyethylene (HDPE)/ethylene vinyl acetate (EVA) blends has been examined with reference to the effect of blend ratio, shear stress, and temperature. The HDPE/EVA blends exhibit pseudoplastic behavior, and the observed rheological behavior of the blends was correlated with the extrudate morphology. The experimental values of the viscosity were compared with the theoretical models. The effect of maleic- and phenolic-modified PE compatibilizers on the viscosity of H70 blend was analyzed and found that compatibilization did not significantly increase the viscosity. The effect of dynamic vulcanization and temperature on the viscosity was also analyzed. The activation energy of the system decreased with increase in EVA content in the system. The phase continuity and phase inversion points of the blends were theoretically predicted and compared with the experimental values. The melt flow index (MFI) values of the blends were also determined and found that the MFI values decreased with increase in EVA content in the system. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers

The Effect of Dynamic Vulcanization on the Properties of Polypropylene/Ethylene-Propylene Diene Terpolymer/Natural Rubber (PP/EPDM/NR) Ternary Blend

The effects of dynamic vulcanization on the process development and some properties, such as tensile properties, swelling index, gel content, crystallinity, and morphology, of the polypropylene (PP)/ethylene-propylene diene terpolymer (EPDM)/natural rubber (NR) blends were investigated. Dynamically vulcanized blends show higher stabilization torque than unvulcanized blends. In terms of tensile properties, the tensile strength and tensile modulus (stress at 100% elongation, M100) of the vulcanized blends have been found to increase as compared with the unvulcanized blends, whereas the elongation at break is higher in the blend with richer EPDM content. These results can be attributed to the formation of cross-linking in the rubber phase. The formation of cross-links in the rubber phase has also been proved by swelling index and gel content. The percentage of crystallinity of the blends is decreased by dynamic vulcanization. Scanning electron microscopy (SEM) micrographs from the surface extraction of the blends support that the cross-links occurred during dynamic vulcanization.

The effects of dynamic vulcanization and compatibilizer on properties of paper sludge‐filled polypropylene/ethylene propylene diene terpolymer composites

AbstractThe effects of dynamic vulcanization (DV) and dynamic vulcanization plus compatibilizer (DVC) of paper sludge (PS) filled polypropylene/ethylene propylene diene terpolymer (PP/EPDM) composites on torque development, mechanical properties, water absorption, morphology, and thermal properties were studied. Results show that DV and DVC composites exhibit higher stabilization torque than unvulcanized composites (UV). The dynamic vulcanized (DV) and dynamic vulcanized plus compatibilizer (DVC) composites exhibit higher tensile strength, elongation at break, and Young's modulus but lower water absorption than unvulcanized composites. The scanning electron microscopy (SEM) study of tensile fracture surface of DV and DVC composites shows the improved interfacial interaction between PS and PP/EPDM matrix. The DV and DVC composites also exhibit better thermal stability and higher crystallinity than unvulcanized PP/EPDM/PS composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008

Effects of Dynamic Vulcanization and Acrylic Acid on Properties of Recycled Poly(vinyl chloride)/Acrylonitrile Butadiene Rubber (PVCr/NBR) Blends

Effects of dynamic vulcanization and acrylic acid (AAc) on processability, mechanical properties, swelling behavior, morphology, and thermal stability of recycled poly(vinyl chloride)/acrylonitrile butadiene rubber (PVCr/NBR) blends were investigated. Blends were prepared in a Haake Rheomix at a temperature of 150°C and a rotor speed of 50 rpm. Recycled poly(vinyl chloride)/acrylonitrile butadiene rubber (PVCr/NBR) blends were also prepared as comparison. It was found that the dynamic vulcanization and the addition of acrylic acid improved the stabilization torque, mechanical energy, stress at peak, stress at 100% elongation (M100), swelling resistance, and thermal stability but decreased the elongation at break of the blends. The introduction of a cross-link into the elastomer phase and better compatibility between PVCr and NBR are responsible for the enhancement of thermal stability and mechanical properties of dynamically vulcanized PVCr/NBR + AAc as evidence from the scanning electron microscopy (SEM) of the tensile fracture surfaces and infrared spectroscopy study of the dynamically vulcanized of PVCr/NBR + AAc shows.

Effects of dynamic vulcanization and glycidyl methacrylate on properties of recycled poly(vinyl chloride)/acrylonitrile butadiene rubber blends

Polymer blends with varying amounts of recycled poly(vinyl chloride) (PVCr) and acrylonitrile butadiene rubber (NBR) have been developed to produce thermoplastic elastomers (TPEs). The effects of dynamic vulcanization and glycidyl methacrylate (GMA) on mechanical and thermal properties, swelling index and morphology properties of the blends were studied. The blends were prepared at 150 °C using a rotor speed of 50 rpm for 11 min. It was found that dynamic cross-linking has enhanced the peak stress, stress at 100% elongation, thermal stability and swelling resistance of dynamically vulcanized PVCr/NBR+GMA blends compared to PVCr/NBR blends. The introduction of cross-links into the elastomer phase and better compatibility between PVCr and NBR are responsible for the enhancement of mechanical properties of dynamically vulcanized PVCr/NBR+GMA blends, as evidenced by the scanning electron microscopy (SEM) of extracted surfaces of the blends.

The Effects of Dynamic Vulcanization by Dicumyl Peroxide (DCP) and N,N-m-Phenylene Bismaleimide (HVA-2) on the Properties of Polypropylene (PP)/Ethylene-Propylene Diene Terpolymer (EPDM)/Natural Rubber (NR) Blends

ABSTRACT This paper discusses some properties of the polypropylene (PP)/ethylene-propylene diene terpolymer (EPDM)/natural rubber (NR) blends, such as tensile properties, heat resistance, gel content, and morphology. Dicumyl peroxide (DCP) and N,N-m-phenylene bismaleimide (HVA-2) and their combination were applied in PP/EPDM/NR blends as cross-link agents. In terms of tensile properties, the combination of DCP with HVA-2 shows the highest tensile strength and elongation at break in all PP/EPDM/NR blend ratios compared to similar blends, except with DCP or HVA-2 alone. The addition of HVA-2 produced blends with good heat resistance, while the combination of DCP with HVA-2 shows the highest gel content dealing with the cross-links formation. SEM micrographs from the surfaces extraction of the blends support that the cross-links have occurred during dynamic vulcanization process.

Thermoplastic elastomeric blend of nitrile rubber and poly(styrene‐co‐acrylonitrile). I. Effect of mixing sequence and dynamic vulcanization on mechanical properties

AbstractThe effects of dynamic vulcanization and blend ratios on mechanical properties and morphology of thermoplastic elastomeric (TPE) compositions, based on blends of nitrile rubber (NBR) and poly(styrene‐co‐acrylonitrile) (SAN), were studied. The TPE composition prepared by adding a rubber‐curatives masterbatch to softened SAN yields higher mechanical properties than that prepared by adding curatives to the softened plastic–rubber preblend. The blends having a higher rubber–plastic ratio (60 : 40 to 80 : 20) display thermoplastic elastomeric behavior, whereas those having a higher plastic–rubber ratio (50 : 50 to 90 : 10) display the behavior of impact‐resistant plastics. DSC studies revealed that NBR and SAN are thermodynamically immiscible. SEM studies of the thermoplastic elastomeric compositions show that SAN forms the matrix in which fine particles of NBR form the dispersed phase. It was further confirmed by dynamic mechanical thermal analysis. Dynamic vulcanization causes a decrease in the size of dispersed particles and improvement in mechanical properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1976–1987, 2003

Dynamic mechanical properties of isotactic polypropylene/nitrile rubber blends: Effects of blend ratio, reactive compatibilization, and dynamic vulcanization

The effect of blend ratio and compatibilization on dynamic mechanical properties of PP/NBR blends was investigated at different temperatures. The storage modulus of the blend decreased with increase in rubber content and shows two Tg's indicating the incompatibility of the system. Various composite models have been used to predict the experimental viscoelastic data. The Takayanagi model fit well with the experimental values. The addition of phenolic modified polypropylene (Ph-PP) and maleic modified polypropylene (MA-PP) improved the storage modulus of the blend at lower temperatures. The enhancement in storage modulus was correlated with the change in domain size of dispersed NBR particles. The effect of dynamic vulcanization using sulfur, peroxide, and mixed system on viscoelastic behavior was also studied. Among these peroxide system shows the highest modulus. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2309–2327, 1997