Effect Of Probe Size Research Articles

Effect of probe size on phase-detection probe measurements of air-water flow properties in hydraulic jumps

This experimental study investigated the air-water flow properties and bubble characteristics in hydraulic jumps with Froude numbers Fr1 = 2.4 and 6.3, using four dual-tip phase detection probes with sensor sizes from 0.25 mm to 0.64 mm. The hydraulic jumps were characterized by a fully breaking roller with substantial air entrainment and turbulent two-phase flow patterns. The measurements encompassed distributions of void fraction, bubble count rate, interfacial velocity and bubble clustering properties and the data sets were consistent with previous studies. The comparison of the different probes showed a small impact of the tested sensor sizes on the air-water flow properties, in terms of the trends, magnitude and maximum values. Some differences were observed in terms of the bubble count rate, with the larger probes detecting a lesser number of bubbles. The trend was further confirmed through a comparison with the data set of Chanson and Brattberg (2000) [10] with a smaller probe sensor size (Ø1 = 0.025 mm), in which the maxima of bubble count rates were almost twice that of the present dataset for identical flow conditions. The present results confirm that the traditional signal processing techniques can be used for relatively small probe sizes, although different approaches might be needed for larger probes which cannot detect sub-millimetric bubbles. Overall, the findings should facilitate the development of sturdier phase-detection needle probes and help breaching the gap between laboratory and prototype.

Effect of Stabilizing Particle Size on the Structure and Properties of Liquid Marbles.

A liquid marble (LM) describes a liquid droplet that is wrapped by nonwetting micro- or nanoparticles and therefore obtains characteristics of a solid powder particle. Here, we investigate the effect of the stabilizing particle size on the resulting structure and properties of the LM. We synthesize a series of polystyrene particles with ultrathin coatings of heptadecafluorooctanesulfonic acid-doped polypyrrole with diameters ranging between 1 and 1000 μm by an aqueous chemical oxidative seeded polymerization of pyrrole. The methodology produced a set of hydrophobic particles with similar surface characteristics to allow the formation of LMs and to probe size effects in the LM formation and stabilization efficiency. We found that particles with a size above 20 μm adsorb as a particle monolayer to the surface of the LM, while smaller particles are adsorbed as ill-defined, multilayered aggregates. These results indicate that the balance between particle-particle interaction and gravity is an important parameter to control the surface structure of the LMs. The assembly behavior and size of the particles also correlated with the mechanical integrity of the LM against fall impact. The mechanical resistance was affected by the gap distance between the inner liquid of the LM and supporting substrate, the capillary forces acting between the particles at the LM surface, and the potential energy that depended on the particle size. Last, we demonstrate that the broadband light-absorbing properties of the polypyrrole shell also allow manipulating the evaporation rate of the inner liquid.

Dual-Probe Atomic Force Microscopy based on tuning fork probes for critical dimension metrology

Atomic force microscopy (AFM) is widely used for nano-dimensional metrology in semiconductor manufacturing and metrological system. However, the conventional AFM can't provide accurate CD characterization of nanostructures, due to its top-down configuration and probe-size effect. In this paper, we develop a dual-probe atomic force microscopy (DPAFM). Compared to conventional optical-lever based AFM, the DPAFM exploits two tuning fork probes that simplifies significantly the setup and can be controlled based on frequency-modulation (FM) mode. The developed DPFAM is implemented that builds a zero-reference point by dual-probe alignment firstly, following which, characterizes nanostructures from two sides independently with the two probes. The final CD feature is determined by matching profiles from the two probes based on the zero-reference point. The capability of the DPAFM is validated by experiments on a CD-standard structure, that achieves the true CD assessment with good accuracy and repeatability.

On the mechanical response of the actomyosin cortex during cell indentations.

A mechanical model is presented to analyze the mechanics and dynamics of the cell cortex during indentation. We investigate the impact of active contraction on the cross-linked actin network for different probe sizes and indentation rates. The essential molecular mechanisms of filament stretching, cross-linking and motor activity, are represented by an active and viscous mechanical continuum. The filaments behave as worm-like chains linked either by passive rigid linkers or by myosin motors. In the first example, the effects of probe size and loading rate are evaluated using the model for an idealized rounded cell shape in which properties are based on the results of parallel-plate rheometry available in the literature. Extreme cases of probe size and indentation rate are taken into account. Afterward, AFM experiments were done by engaging smooth muscle cells with both sharp and spherical probes. By inverse analysis with finite element software, our simulations mimicking the experimental conditions show the model is capable of fitting the AFM data. The results provide spatiotemporal dependence on the size and rate of the mechanical stimuli. The model captures the general features of the cell response. It characterizes the actomyosin cortex as an active solid at short timescales and as a fluid at longer timescales by showing (1) higher levels of contraction in the zones of high curvature; (2) larger indentation forces as the probe size increases; and (3) increase in the apparent modulus with the indentation depth but no dependence on the rate of the mechanical stimuli. The methodology presented in this work can be used to address and predict microstructural dependence on the force generation of living cells, which can contribute to understanding the broad spectrum of results in cell experiments.

Transport of probe particles in a polymer network: effects of probe size, network rigidity and probe-polymer interaction.

Fundamental understanding of the effect of microscopic parameters on the dynamics of probe particles in different complex environments has wide implications. Examples include diffusion of proteins in biological hydrogels, porous media, polymer matrix, etc. Here, we use extensive molecular dynamics simulations to investigate the dynamics of the probe particle in a polymer network on a diamond lattice, which provides substantial crowding to mimic the cellular environment. Our simulations show that the dynamics of the probe increasingly becomes restricted, non-Gaussian and subdiffusive on increasing the network rigidity, binding affinity and probe size. In addition, the velocity autocorrelation functions show negative dips owing to the viscoelasticity and caging due to the surrounding network. These observations go with the general experimental findings. Importantly, for a probe particle of size comparable to the mesh size, unrestricted motion engulfing large length scales has been observed. This happens with a more flexible polymer network, which is easily pushed by the bigger probe. On increasing the rigidity of the network, the bigger probe can not efficiently push the network and as a result the long tail disappears. Our study gives a general qualitative picture of the transport of probes in a gel-like medium, as encountered in different contexts.

Flame exposure time on Langmuir probe degradation, ion density, and thermionic emission for flame temperature.

The paper examines the effect of exposure time of Langmuir probes in an atmospheric premixed methane-air flame. The effects of probe size and material composition on current measurements were investigated, with molybdenum and tungsten probe tips ranging in diameter from 0.0508 to 0.1651 mm. Repeated prolonged exposures to the flame, with five runs of 60 s, resulted in gradual probe degradations (-6% to -62% area loss) which affected the measurements. Due to long flame exposures, two ion saturation currents were observed, resulting in significantly different ion densities ranging from 1.16 × 1016 to 2.71 × 1019 m-3. The difference between the saturation currents is caused by thermionic emissions from the probe tip. As thermionic emission is temperature dependent, the flame temperature could thus be estimated from the change in current. The flame temperatures calculated from the difference in saturation currents (1734-1887 K) were compared to those from a conventional thermocouple (1580-1908 K). Temperature measurements obtained from tungsten probes placed in rich flames yielded the highest percent error (9.66%-18.70%) due to smaller emission current densities at lower temperatures. The molybdenum probe yielded an accurate temperature value with only 1.29% error. Molybdenum also demonstrated very low probe degradation in comparison to the tungsten probe tips (area reductions of 6% vs. 58%, respectively). The results also show that very little exposure time (<5 s) is needed to obtain a valid ion density measurement and that prolonged flame exposures can yield the flame temperature but also risks damage to the Langmuir probe tip.

Influence of extrinsic operational parameters on salt diffusion during ultrasound assisted meat curing

The present study investigated the effect of geometric parameters of the ultrasound instrument during meat salting in order to enhance salt diffusion and salt distribution in pork meat on a lab scale. The effects of probe size (∅2.5 and 1.3cm) and of different distances between the transducer and the meat sample (0.3, 0.5, and 0.8cm) on NaCl diffusion were investigated. Changes in the moisture content and NaCl gain were used to evaluate salt distribution and diffusion in the samples, parallel and perpendicular to ultrasound propagation direction. Results showed that 0.3cm was the most efficient distance between the probe and the sample to ensure a higher salt diffusion rate. A distance of 0.5cm was however considered as a trade-off distance to ensure salt diffusion and maintenance of meat quality parameters. The enhancement of salt diffusion by ultrasound was observed to decrease with increased horizontal distance from the probe. This study is of valuable importance for meat processing industries willing to apply new technologies on a larger scale and with defined operational standards. The data suggest that the geometric parameters of ultrasound systems can have strong influence on the efficiency of ultrasonic enhancement of NaCl uptake in meat and can be a crucial element in determining salt uptake during meat processing.

Anomalous diffusion of poly(ethylene oxide) in agarose gels

We report on the effect of probe size and diffusion time of poly(ethylene) oxide in agarose gels. Time-dependence of the diffusion coefficient, reflecting anomalous diffusion, was observed for poly(ethylene) oxide chains with hydrodynamic radii exceeding about 20nm at an agarose concentration of 2%. The main conclusion is that the pore distribution includes pores that are only several nm across, in agreement with scattering reports in the literature. Interpretation of the diffusion coefficient dependence on the probe size based on a model of entangled rigid rods yielded a rod length of 72nm.

Simultaneous specific heat and thermal conductivity measurement of individual nanostructures

Fundamental phonon transport properties in semiconductor nanostructures are important for their applications in energy conversion and storage, such as thermoelectrics and photovoltaics. Thermal conductivity measurements of semiconductor nanostructures have been extensively pursued and have enhanced our understanding of phonon transport physics. Specific heat of individual nanostructures, despite being an important thermophysical parameter that reflects the thermodynamics of solids, has remained difficult to characterize. Prior measurements were limited to ensembles of nanostructures in which coupling and sample inhomogeneity could play a role. Herein we report the first simultaneous specific heat and thermal conductivity measurements of individual rod-like nanostructures such as nanowires and nanofibers. This technique is demonstrated by measuring the specific heat and thermal conductivity of single ∼600–700 nm diameter Nylon-11 nanofibers (NFs). The results show that the thermal conductivity of the NF is increased by 50% over the bulk value, while the specific heat of the NFs exhibits bulk-like behavior. We find that the thermal diffusivity obtained from the measurement, which is related to the phonon mean free path (MFP), decreases with temperature, indicating that the intrinsic phonon Umklapp scattering plays a role in the NFs. This platform can also be applied to one- and two- dimensional semiconductor nanostructures to probe size effects on the phonon spectra and other transport physics.

The finite probe size effect in fluctuation measurements; application to dusty plasmas

The effect of the finite probe size in plasma fluctuation measurements is revisited for dusty plasmas, where it has been argued that dust leads to a significant low-frequency enhancement in the spectral densities of ion density fluctuations, which can constitute the physical basis of a dust diagnostic technique. Theoretical predictions for the spectral modifications are presented and the dust acoustic mode contribution is analysed. The finite probe size effect is treated within the volume average approach, which introduces geometry dependent form factors that are calculated for spherical and cylindrical probes. The volume average approach is compared with the typically employed cutoff wavenumber approximation for various dust and plasma parameters. The contribution of temperature fluctuations to the spectral density of current fluctuations is also evaluated.

CuInP₂S₆ Room Temperature Layered Ferroelectric.

We explore ferroelectric properties of cleaved 2-D flakes of copper indium thiophosphate, CuInP2S6 (CITP), and probe size effects along with limits of ferroelectric phase stability, by ambient and ultra high vacuum scanning probe microscopy. CITP belongs to the only material family known to display ferroelectric polarization in a van der Waals, layered crystal at room temperature and above. Our measurements directly reveal stable, ferroelectric polarization as evidenced by domain structures, switchable polarization, and hysteresis loops. We found that at room temperature the domain structure of flakes thicker than 100 nm is similar to the cleaved bulk surfaces, whereas below 50 nm polarization disappears. We ascribe this behavior to a well-known instability of polarization due to depolarization field. Furthermore, polarization switching at high bias is also associated with ionic mobility, as evidenced both by macroscopic measurements and by formation of surface damage under the tip at a bias of 4 V-likely due to copper reduction. Mobile Cu ions may therefore also contribute to internal screening mechanisms. The existence of stable polarization in a van-der-Waals crystal naturally points toward new strategies for ultimate scaling of polar materials, quasi-2D, and single-layer materials with advanced and nonlinear dielectric properties that are presently not found in any members of the growing "graphene family".

Interactions and Diffusion in Fine-Stranded β-lactoglobulin Gels Determined via FRAP and Binding

The effects of electrostatic interactions and obstruction by the microstructure on probe diffusion were determined in positively charged hydrogels. Probe diffusion in fine-stranded gels and solutions of β-lactoglobulin at pH 3.5 was determined using fluorescence recovery after photobleaching (FRAP) and binding, which is widely used in biophysics. The microstructures of the β-lactoglobulin gels were characterized using transmission electron microscopy. The effects of probe size and charge (negatively charged Na2-fluorescein (376Da) and weakly anionic 70kDa FITC-dextran), probe concentration (50 to 200 ppm), and β-lactoglobulin concentration (9% to 12% w/w) on the diffusion properties and the electrostatic interaction between the negatively charged probes and the positively charged gels or solutions were evaluated. The results show that the diffusion of negatively charged Na2-fluorescein is strongly influenced by electrostatic interactions in the positively charged β-lactoglobulin systems. A linear relationship between the pseudo-on binding rate constant and the β-lactoglobulin concentration for three different probe concentrations was found. This validates an important assumption of existing biophysical FRAP and binding models, namely that the pseudo-on binding rate constant equals the product of the molecular binding rate constant and the concentration of the free binding sites. Indicators were established to clarify whether FRAP data should be analyzed using a binding-diffusion model or an obstruction-diffusion model.

Computational study of tip apex symmetry characterization in high-resolution atomic force microscopy

Simultaneous atomic force microscopy (AFM)/scanning tunnelling microscopy (STM) is a powerful combination of two complementary techniques that enables high-resolution measurement of surface physical and chemical properties. Although blind characterization of the chemical structure of a surface or probe tip is extremely challenging, recent experimental reports suggest that measurement of the tip bonding symmetry is possible when it interacts with a well-defined sample, such as an adsorbed molecule. In order to gain understanding into the relationship between the symmetry observed in the experiments and the actual tip structure, we explore computationally the mechanism through which the tip apex electronic density and angular stiffness is revealed in AFM images. Our study is based on idealized 1-atom models of the surface, which allow us to isolate the effects of probe size and reactivity. Our results show that image symmetry is directly related to tip symmetry and that the contrast diminishes with larger or more reactive sample atoms. We also find that that the mechanics of the probe–sample interaction are not trivial even for the most idealized models, and that the electronic density distribution around the apex atom is also more complex than what can be inferred from the experimental images.

PFG-NMR self-diffusion in casein dispersions: Effects of probe size and protein aggregate size

The self-diffusion coefficients of different molecular weight PEGs (Polyethylene glycol) and casein particles were measured, using a pulsed-gradient nuclear magnetic resonance technique (PFG-NMR), in native phosphocaseinate (NPC) and sodium caseinate (SC) dispersions where caseins are not structured into micelles. The dependence of the PEG self-diffusion coefficient on the PEG size, casein concentration, the size and the mobility of casein obstacle particles are reported. Wide differences in the PEG diffusion coefficients were found according to the casein particle structure. The greatest reduction in diffusion coefficients was found in sodium caseinate suspensions. Moreover, sodium caseinate aggregates were found to diffuse more slowly than casein micelles for casein concentrations >9 g/100 g H2O. Experimental PEG and casein diffusion findings were analyzed using two appropriate diffusion models: the Rouse model and the Speedy model, respectively. According to the Speedy model, caseins behave as hard spheres below the close packing limit (10 g/100 g H2O for SC (Farrer & Lips, 1999) and 15 g/100 g H2O for NPC (Bouchoux et al., 2009)) and as soft particles above this limit. Our results provided a consistent picture of the effects of diffusant mass, the dynamics of the host material and of the importance of the casein structure in determining the diffusion behavior of probes in these systems.

Effect of probe size and energy (M versus XL probe) on the detection of liver stiffness using transient elastography (Fibroscan)

Effect of probe size and energy (M versus XL probe) on the detection of liver stiffness using transient elastography (Fibroscan)

Imaging with low-voltage scanning transmission electron microscopy: A quantitative analysis

A dedicated specimen holder has been designed to perform low-voltage scanning transmission electron microscopy in dark field mode. Different test samples, namely InGaAs/GaAs quantum wells, InGaAs nanowires and thick InGaAs layers, have been analysed to test the reliability of the model based on the proportionality to the specimen mass-thickness, generally used for image intensity interpretation of scattering contrast processes. We found that size of the probe, absorption and channelling must be taken into account to give a quantitative interpretation of image intensity. We develop a simple procedure to evaluate the probe-size effect and to obtain a quantitative indication of the absorption coefficient. Possible artefacts induced by channelling are pointed out. With the developed procedure, the low voltage approach can be successfully applied for quantitative compositional analysis. The method is then applied to the estimation of the In content in the core of InGaAs/GaAs core-shell nanowires.

Effect of probe size and measurement strategies on assessment of freeform profile deviations using coordinate measuring machine

Freeform profiles and surfaces have wider engineering applications. Designers use B-splines, Non-Uniform Rational B-splines, etc. to represent the freeform profiles in CAD, while the manufacturers employ machines with controllers based on approximating functions or splines that can cause deviations in manufactured parts. Deviations also creep in during the manufacturing operations. Therefore the manufactured freeform profiles have to be verified for conformance to design specification. Different points on the profile are probed using a coordinate measuring machine (CMM) and a substitute profile is established from the CMM data for comparison with design profile. The sample points are distributed according to different strategies. In the present work, two new strategies of distributing the points on the basis of curve length and dominant points are proposed considering the geometrical nature of the profiles. Metrological aspects such as probe contact and margins to be provided at the ends have also been included. The results are discussed in terms of form deviation with reference to substitute profile and positional deviation between design and substitute profiles, and compared with results of the strategies suggested in the literature.

Quantifying Diffusion in a Biofilm of Streptococcus mutans

In biofilms, diffusion may limit the chemical activity of nutrients, toxic compounds, and medicines. This study provides direct, noninvasive insight into the factors that will most effectively limit the transport of antibiotics and biocides in biofilms. Self-diffusion coefficients have been determined for a number of fluorescent probes in biofilms of Streptococcus mutans using fluorescence correlation spectroscopy. The effects of probe size and charge and the roles of biofilm pH, ionic strength, and heterogeneity were studied systematically. The relative diffusion coefficients (D in the biofilm divided by that in water) decreased with increasing probe size (3,000-molecular-weight [3K], 10K, 40K, 70K, and 2,000K dextrans). Studies using variably charged substrates (tetramethylrhodamine, Oregon Green, rhodamine B, and rhodamine 6G) showed that the self-diffusion coefficients decreased with an increasing negative charge of the fluorescent probes. No significant effect was observed for changes to the ionic strength (10⁻⁴ to 10⁻¹ M) or pH (4 to 9) of the biofilm. Biofilm heterogeneity was responsible for variations of ca. one order of magnitude in the diffusion coefficients.

Poster — Thur Eve — 09: Effects of Small Sample Size on Diffuse Reflectance Spectroscopy for the Identification of Brain Tumours

An optical system using diffuse reflectance spectroscopy (DRS) and time‐resolved laser induced fluorescence spectroscopy (TR‐LIFS) is being developed to identify surgical margins during brain tumour resection. Since initial trials will be performed ex vivo on small samples, we investigated our ability to perform DRS for these small sample volumes. We examined both the effects of decreasing sample volume on the DRS signal and decreasing probe size on our ability to recover optical properties. Sample volume effects were studied by performing DRS measurements on bovine brain tissue samples of various sizes and comparing the signals to those for very large samples. A decrease in DRS signal strength was observed at sample volumes of less than 500 mm3. Probe size effects were studied using Monte Carlo simulations to obtain the spatially‐resolved reflectance using the optical properties of human brain tissue. Varying amounts of noise were added to the reflectance, and optical properties were recovered by fitting to Monte Carlo generated reflectance curves. The recovered properties were compared to their actual values as the maximum radius used for fitting was reduced. Our ability to recover the absorption coefficient was improved when fitting to absolute reflectance data.

Reproducibility and repeatability of measuring the electrical impedance of the pregnant human cervix-the effect of probe size and applied pressure

BackgroundThe utility of cervical electrical impedance spectroscopy (EIS) as a diagnostic tool is being investigated in clinical trials. We sought to assess the reliability of two different sizes of tetrapolar probes used in measuring cervical impedance.MethodsCervical transfer impedance was measured at 14 frequencies between 76 and 625 000 Hz from 11 pregnant subjects at term. Repeated measurements were taken with two probes (3 mm and 12 mm diameter) applied softly (approximately 0.7 Newton of force), and firmly (approximately 2.2 Newton) to the surface of the cervix by two observers. The intra-class correlation coefficient (ICC), coefficient of variation (CV) and repeatability standard deviations (SD) were derived from these measurements and compared.ResultsMeasurements taken by one observer were highly repeatable for both probes as demonstrated by high ICC and low CV values. Probe performance was improved further by firm application. Firm application of the 3 mm probe resulted in ICC values that ranged from 0.936 to 0.986 (p = 0.0001) and CV values between 1.0 and 3.4%. Firm pressure with the 12 mm probe resulted in ICC values that ranged between 0.914 and 0.988 (p = 0.0001) with CV values between 0.7 and 2.1%. In addition, the repeatability SD was low across all frequencies implying that there was low intra-observer variability. Measurements taken by 2 observers with firm application of the 12 mm probe demonstrated moderate reproducibility between 9.8 and 156 kHz, the frequency range in which previous clinical studies have shown predictive association between high cervical resistivity and vaginal delivery: ICC values ranged between 0.528 and 0.638 (p < 0.05), CV values were between 3.3 and 5.2% and reproducibility SD values were also low. In contrast the 3 mm probe demonstrated poor reproducibility at all study frequencies.ConclusionMeasuring cervical resistivity by a single observer with both the 3 and 12 mm probes is highly repeatable whilst inter-observer reproducibility is poor with the 3 mm probe but moderately good when the 12 mm probe is firmly applied to the cervix in the frequency range 9.8 to 156 kHz, consistent with our observations of probe performance in clinical trials.