E-beam Irradiation Research Articles

Room temperature electron beam sensitive viscoplastic response of ultra-ductile amorphous olivine films

The mechanical properties of amorphous olivine (a-olivine) deformed at room temperature are investigated in situ in a TEM under uniaxial tension using a Push-to-Pull (PTP) device. Thin films of a-olivine were produced by pulsed laser deposition (PLD). With or without electron irradiation, a-olivine films deform plastically, with a gradual transition that makes impossible the determination of a precise threshold. The strength attains values up to 2.5 GPa. The increasing strain-rate in load control results in an apparent softening with stress drop. The fracture strain reaches values close to 30 % without e-beam irradiation. Under electron illumination at 200 kV, the strength is lower, around 1.7 GPa, while higher elongations close to 36 % are obtained. Alternating beam-off and beam-on sequences lead to exceptionally large fracture strains equal to 68 % at 200 kV and 139 % at 80 kV. EELS measurements were performed to characterize the interaction between the electron beam and a-olivine. At a voltage of 80 kV, radiolysis accompanied by oxygen release dominates whereas at high voltage (300 kV) the interaction is dominated by knock-on type defects. Radiolysis is also the main interaction mechanism at 200 kV with low exposition which corresponds to most of our in situ TEM deformation experiments. To interpret the mechanical data, a simple 1D model has been developed to rationalize the load transfer between the PTP device and the specimen. The strain-rate sensitivity is 6 to 10 times higher when a-olivine is deformed under electron irradiation.

Efficient Isolation of Cellulose Nanocrystals from Seaweed Waste via a Radiation Process and Their Conversion to Porous Nanocarbon for Energy Storage System.

This article presents an efficient method for isolating cellulose nanocrystals (CNcs) from seaweed waste using a combination of electron beam (E-beam) irradiation and acid hydrolysis. This approach not only reduces the chemical consumption and processing time, but also improves the crystallinity and yield of the CNcs. The isolated CNcs were then thermally annealed at 800 and 1000 °C to produce porous nanocarbon materials, which were characterized using scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy to assess their structural and chemical properties. Electrochemical testing of electrical double-layer capacitors demonstrated that nanocarbon materials derived from seaweed waste-derived CNcs annealed at 1000 exhibited superior capacitance and stability. This performance is attributed to the formation of a highly ordered graphitic structure with a mesoporous architecture, which facilitates efficient ion transport and enhanced electrolyte accessibility. These findings underscore the potential of seaweed waste-derived nanocarbon as a sustainable and high-performance material for energy storage applications, offering a promising alternative to conventional carbon sources.

Improvement on gel properties of chicken myofibrillar protein with electron beam irradiation: Based on protein structure, gel quality, water state

This study aimed to investigate the effects of electron beam (E-beam) irradiation at different doses (0–15 kGy) on the solubility, rheological properties, emulsification characteristics, and moisture distribution of chicken myofibrillar proteins (MPs). Irradiation treatment notably increased the solubility, surface hydrophobicity, emulsification properties, and apparent viscosity of MPs, based on conformational changes caused by irradiation-induced oxidative denaturation of proteins. However, high doses of irradiation (15 kGy) induced in excessive cross-linking and aggregation of proteins, reducing the solubility, emulsification properties, and shear stress. Degradation of myosin heavy and light chains in irradiated MPs increased the content of β-turns and random coils. Additionally, the initial relaxation times of T21 and T22 in irradiated protein gels were reduced, and the peak value of P21 was increased, which improved the water-capturing ability of protein gels. Altogether, these results findings suggest that electron beam irradiation can be applied as a potential technique for modifying muscle proteins.

The Influence of the Structural Architecture on the Swelling Kinetics and the Network Behavior of Sodium-Alginate-Based Hydrogels Cross-Linked with Ionizing Radiation.

The present work discusses the influence of the structural architecture of sodium alginate-co-acrylic acid-poly(ethylene) oxide hydrogels, crosslinked through electron beam (e-beam) radiation processing. The most important properties of the hydrogels were studied in detail to identify a correlation between the architecture of the hydrogels and their properties. Furthermore, the effect of sodium alginate (NaAlg) concentration, the amounts of the polymer blend, and the size of the samples on hydrogel properties were investigated. The results show that the hydrogels cross-linked (0.5% and 1% NaAlg) with 12.5 kGy exhibit improved physicochemical properties. High gel fraction levels (exceeding 83.5-93.7%) were achieved. Smaller hydrogel diameter (7 mm) contributed to a maximum swelling rate and degree of 20.440%. The hydrogel network was dependent on the hydrogels' diameter and the amount of polymer blend used. The hydrogels best suited the first-order rate constants and exhibited a non-Fickian diffusion character with diffusion exponent values greater than 0.5. This study indicates that the cross-linked hydrogel has good properties, particularly because of its high degree of swelling and extensive stability (more than 180 h) in water. These findings show that hydrogels can be effectively applied to the purification of water contaminated with metals, dyes, or even pharmaceuticals, as well as materials with a gradual release of bioactive chemicals and water retention.

Comparative Review on E-Beam and Gamma Radiation Sterilization Methods: Effectiveness, Safety, and Cost Considerations

Comparative Review on E-Beam and Gamma Radiation Sterilization Methods: Effectiveness, Safety, and Cost Considerations

Appearance of spectral dip in the cathodoluminescence spectrum of negatively charged nitrogen-vacancy centers in diamonds

Negatively charged nitrogen-vacancy (NV−) centers in diamond produce a characteristic optical zero-phonon line (ZPL) at 637 nm. This emission line can be observed under optical excitation (i.e. photoluminescence), but is rarely observed under electron excitation (i.e. cathodoluminescence). This study reports that low-temperature (80 K) and low energy (5 keV) cathodoluminescence spectroscopy is able to detect emission peak or spectral dip at the ZPL of NV− centers. The spectral dip was observed in the diamond samples with high concentration of NV− centers produced by high-energy (2 MeV) e-beam (EB) irradiation. The effects of EB irradiation fluence, NV− centers concentration and substitutional nitrogen concentration on the formation of spectral dip were discussed, and a model based on the NV− absorption of NV0 emission sideband is proposed.

Synergistic Effect of Laser, Water Vapor, and Electron-Beam on the Degradation of Quasi-Two-Dimensional Ruddlesden-Popper Perovskite Flakes.

Understanding the effects of laser light, water vapor, and energetic electron irradiation on the intrinsic properties of perovskites is important in the development of perovskite-based solar cells. Various phase transition and degradation processes have been reported when these agents interact with perovskites separately. However, detailed studies of their synergistic effects are still missing. In this work, the synergistic effect of three factors (exposure to laser light, water vapor, and e-beam) on the optical and physical properties of two-dimensional (2D) Ruddlesden-Popper (RP) perovskite flakes [(BA)2(MA)2Pb3Br10] has been investigated in an environmental cell. When the perovskite flakes were subjected to moderate laser irradiation in a humid environment after prior e-beam irradiation, the photoluminescence (PL) peak centered at 480 nm vanished, while a new PL peak centered at 525 nm emerged, grew, and then quenched. This indicates the degradation process of the 2D RP perovskite was a phase transition to a three-dimensional (3D) perovskite [MAPbBr3] followed by the degradation of 3D perovskite. The spatial distribution of the 525 nm PL signal shows that this phase-transition process spreads across the flake to the area as far as ∼40 μm from the laser spot. Without humidity, the phase transition happened in the laser-irritated area but did not spread, which suggests that moisture enhanced the ion migration from the laser-scanned area to the rest of the flake and accelerated the phase transition in the nearby area. Experiments with no prior e-beam irradiation show that e-beam irradiation is the key to activating the 2D-3D phase transition. Therefore, when the three factors work synergistically, a conversion from the 2D RP perovskite into the 3D perovskite is not localized and propagates through the perovskite. These findings contribute to our understanding of the complex interactions between external stimuli and perovskite materials, thereby advancing the development of efficient and stable perovskite-based solar cells.

Effects of gamma, electron beam, and X-ray irradiation on the plastic components of a universal bone cement mixer medical device

Due to market and regulatory pressures, many healthcare manufacturers are considering alternatives to cobalt-60 gamma radiation, including accelerator-based electron beam (E-beam) and X-ray radiation for product sterilization. In this work, the effects of irradiation on a representative medical product, comprised of eight distinct polymer materials, were directly compared for three radiation technologies – cobalt-60 gamma, E-beam, and X-ray – at four dose levels (15, 25, 50, and 70 kGy). The objective was to determine how radiation effects (deleterious or beneficial) are influenced by source and dose level, with the specific goal of determining whether E-beam radiation and/or X-ray radiation could be viable alternatives to gamma radiation for device sterilization. The specific product considered is a single-use medical device for orthopedic surgery, the Stryker Instruments MixeVac III bone cement mixer, which is currently sterilized using gamma radiation from cobalt-60 sources. Following ASTM International standards and input from the manufacturer, we characterized the effects of the three radiation sources on product functionality as well as on the mechanical and optical properties of the constituent polymers. Results indicate that although measurable differences in properties between the standard gamma irradiated materials and the alternative E-beam and X-ray irradiated materials were observed, those differences were small. Statistically significant differences were noted in the case of yellowness index for polyvinyl chloride, high-density polyethylene, and polycarbonate, and in the case of tensile elongation at break for high impact polystyrene and polyvinyl chloride. In general, the results of this study support the viability of E-beam and X-ray radiation as alternative options to cobalt-60 gamma radiation for sterilization of Stryker single-use universal bone cement mixer medical devices.

Experimental design of size variation in albumin nanoparticles synthesized by electron beam

Protein-based nanoparticles have garnered significant interest for their potential in theranostic applications, including cancer treatment and nuclear medicine. Plasma proteins are particularly appealing due to their ability to bypass the rapid clearance typically associated with synthetic particles. Human serum albumin (HSA), for example, is already utilized in diagnostic procedures such as lymphoscintigraphy and sentinel lymph node detection and in cancer treatments where it delivers therapeutic agents in nanoparticulate form. Among the various techniques for synthesizing protein nanoparticles, ionizing radiation stands out for its ability to maintain good size control and preserve the protein's three-dimensional structure. Factors such as the reaction precursor, pH, protein concentration, presence of a stabilizer, and irradiation dose can all influence the size and shape of the resulting nanoparticles. This study sought to identify a correlation between the size of albumin nanoparticles and reaction parameters, including protein concentrations, the ionic content of the buffer solution, and the e-beam irradiation dose. We conducted different synthesis methods with varying BSA concentrations, using two different buffers and varying radiation doses. The resulting nanoparticles were evaluated using Dynamic Light Scattering. The size data were statistically analyzed using SAS Studio, SAS JMP, and WEKA software to identify correlations among the synthesis variables. Our observations primarily revealed that lower protein concentrations consistently resulted in smaller particles. Additionally, using Tris-HCl buffer as a medium led to a more proportional growth of particles with increases in concentration and irradiation dose. These findings suggest that Tris buffer is more suitable for BSA nanoparticle synthesis, as increased albumin concentration and radiation dose resulted in more consistent size control.

Removal of Fexofenadine and Montelukast Drugs from Aquatic Environment Using a Rhodotron Accelerator

Introduction: Nowadays, the management of drug effluents, as emerging pollutants, has attracted great attention due to human health and ecological adverse effects. During the COVID-19 pandemic, two drugs, Fexofenadine and Montelukast, have been used in large quantities for patients with lung involvement. The aim of this study is to investigate the feasibility of removing Fexofenadine and Montelukast and determine the removal kinetics. Material and methods: In this study, we used Rhodotron accelerator to determine kinetic coefficients for the removal of drugs. Our research focused on studying the kinetics of E-Beam radiation reactions and the generation of significant amounts of free radicals during these processes. We employed first-order and second-order kinetic models under laboratory conditions, taking into account various influencing factors to establish the rate of removal. Results: The results showed that the decomposition of Fexofenadine and Montelukast drugs by high-energy E-Beam bending process is a pseudo-first-order reaction with a coefficient of more than 0.9105 and 0.998, respectively. The results showed that the reaction rate constant depended significantly on the initial concentration of Fexofenadine and Montelukast drugs and their molecular structure. Conclusion: Using a Rhodotron accelerator is important for removing Fexofenadine and Montelukast from the aquatic environment.

Impacts of radiation sources on structures and electrochemical performance of SiO2/C composite anodes for Li-ion batteries

Application of radiation with highly energetic electrons and ions can be an alternative method to modify structures of crystalline materials. This radiation can potentially induce phase transformations while preserving some physical characteristics and morphology of the materials, hence impacting their useful properties. Here, we report the impacts of e-beam and gamma radiation on the structures and electrochemical performance of SiO2/C anodes for Li-ion batteries (LIB) obtained from rice husk ash (RHA). The effects of radiation sources on structural and physical properties are investigated using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), X-ray fluorescence spectrometry (XRF), electron microscopy, and Raman spectroscopy. After irradiation-induced processes using e-beam and gamma radiation at 1000 kGy, the mean diameters of the SiO2 particles were around 30 ± 10 and 27 ± 10 nm, respectively, while retaining their round-shaped particle morphology. Both radiation sources induce formation of disordered carbon structure as indicated by the higher ID/IG Raman peaks ratios than the pristine sample. Electrochemical properties were studied using half-coin type cells. The modified structure of SiO2/C anodes caused by irradiation showed improved electrochemical performance, compared with pristine material.

Investigation of the surface characteristics of WC–Co structures under Local E-beam irradiation via experiments and molecular dynamics simulations

Investigation of the surface characteristics of WC–Co structures under Local E-beam irradiation via experiments and molecular dynamics simulations

Effects of Electron Beam Radiation on the Phenolic Composition and Bioactive Properties of Olive Pomace Extracts.

Olive pomace is an agro-industrial waste product generated from the olive oil industry and constituted by bioactive compounds with potential applications in several industrial sectors. The purpose of this work was to evaluate the effects of electron beam (e-beam) radiation on olive pomace, specifically on phenolic compounds (by HPLC-DAD-ESI/MS) and the bioactive properties (antioxidant, antiproliferative, and antimicrobial activities) of crude olive pomace (COP) and extracted olive pomace (EOP) extracts. The amount of total flavonoid content and the reducing power of COP extracts were higher than those obtained for EOP extracts. The results suggested that e-beam radiation at 6 kGy increased both total phenolic and total flavonoid contents as well as the reducing power of COP extracts, due to the higher extractability (>2.5-fold) of phenolic compounds from these samples, while decreasing the scavenging activity of extracts. The extracts of both olive pomaces showed antibacterial potential, and COP extracts at 400 µg/mL also presented antiproliferative activity against A549, Caco-2, 293T, and RAW264.7 cell lines, with both properties preserved with the e-beam treatment. All in all, e-beam radiation at 6 kGy appears to be a promising technology to valorize the pollutant wastes of the olive oil industry through enhancing phenolic extractability and bioactive properties, and, furthermore, to contribute to the environmental and economical sustainability of the olive oil industry.

Mitigating Gas Evolution in Electron Beam-Induced Gel Polymer Electrolytes Through Bi-Functional Cross-Linkable Additives.

The current high-capacity lithium-ion batteries (LIBs), reliant on flammable liquid electrolytes (LEs) and nickel-rich cathodes, are plagued by safety hazards, especially the risk of hazardous gas release stemming from internal side reactions. To address these safety concerns, an electron beam (E-beam)-induced gel polymer electrolyte (E-Gel) is introduced, employing dipentaerythritol hexaacrylate (DPH) as a bi-functional cross-linkable additive (CIA). The dual roles of DPH are exploited through a strategically designed E-beam irradiation process. Applying E-beam irradiation on the pre-cycled cells allows DPH to function as an additive during the initial cycle, establishing a protective layer on the surface of the anode and cathode and as a cross-linker during the E-beam irradiation step, forming a polymer framework. The prepared E-Gel with CIA has superior interfacial compatibility, facilitating lithium-ion diffusion at the electrode/E-Gel interface. The electrochemical assessment of 1.2 Ah pouch cells demonstrates that E-Gel substantially reduces gas release by 2.5 times compared to commercial LEs during the initial formation stage and ensures superior reversible capacity retention even after prolonged cycling at 55°C. The research underscores the synergy of bifunctional CIA with E-beam technology, paving the way for large-scale production of safe, high-capacity, and commercially viable LIBs.

Investigating the influence of E-beam irradiated sorghum flour on the structure, physicochemical properties, and processing suitability of sorghum/wheat mixed flour-dough-bread: A related mechanism

To improve the processing suitability of sorghum flour for staple food applications of sorghum, this study uses E-beam irradiation (EBI) to pre-treat it to investigate the influence of EBI dose on the structure and properties of the mixed flour-dough-bread. The results showed that EBI enhanced mixed flour solubility by improving the components' structure or functionality of sorghum flour, reducing its swelling power, viscosity, and thermal properties. The fermentation properties of the mixed dough reached optimal at 4 kGy, and were almost identical to those of wheat dough. In addition, the microstructure of the mixed flour dough was optimized at 4 kGy, and the textural properties of its bread were also improved. Low-dose EBI can improve the processing suitability of sorghum flour and reduce the destruction of the gluten network of mixed doughs by miscellaneous grains, which is a promising application for processing other cereal-based products.

Impacts of e-beam irradiation on microbial contamination and quality of Chinese medical formulas QingXuan tablets

Applying electron beam irradiation (EBI) technology to remove microbial contamination is a potential way to improve the efficiency of Chinese medical formula preservation. In this study, Qingxuan tablets (QXT) were irradiated at doses of 3, 5, 9, and 13 kGy of the electron beam, to investigate the impacts of EBI on the microbial load, physical properties, color, bioactive content, antioxidant activity, chromatograms, and spectral similarity of QXT. The results showed that EBI treatment at 13 kGy reduced the population of the total aerobic bacteria and the total molds and yeast of QXT to <200 CFU/g. Irradiation had no significant (P > 0.05) effect on the physical properties and color of QXT. However, the bioactive content of QXT was significantly lower at a dose of 13 kGy compared to unirradiated samples. The free radical scavenging capacity of QXT remained preserved after irradiation. High-performance liquid chromatography (HPLC), Fourier transforms infrared spectroscopy (FTIR), and ultraviolet–visible spectroscopy (UV–Vis) analyses showed that the difference in the chemical content between irradiated QXT and unirradiated samples gradually increased as the dose was increased from 0 kGy to 13 kGy. These results suggest that EBI can be used to sterilize and preserve Chinese medical formulas, but the irradiation dose should be controlled to prevent changes in quality.

UV and pulsed electron beam radiation for effective bisphenol A degradation

The paper presents the results of studying the efficiency of the bisphenol A transformation in water exposed to ultraviolet radiation and a high-energy-pulse-electron beam (e-beam). It has been shown that in both cases, degradation of dissolved bisphenol A occurs, accompanied by an increase in the absorption coefficient in the wavelength region of more than 300 nm. After exposure, products were recorded that fluoresced in the region of more than λ = 400 nm. The fluorescent transformation product of bisphenol A in water (λ = 425 nm) was maximum formatted after an KrCl excilamp irradiated, and under the action of an e-beam, the accumulation of this product was minimal. Under e-beam radiation (170 keV) the efficiency of bisphenol A (1 mM) removal reached 97%. The data obtained allow us to develop ideas about photolysis and radiolysis in natural water systems when knowledge about targeted and optimal conditions for the degradation of bisphenol A is needed.

Improvement of sorghum-wheat blended flours by E-beam irradiation: Physicochemical properties, rheological behavior, microstructure, and quality properties

To enhance the processing suitability of blended flours, this study used 4 kGy E-beam irradiated (EBI) sorghum flour in different ratios blended with wheat flour and further verified the improvement mechanism of the processed products under the optimal ratios. The results suggested that the EBI can mitigate the deterioration of the blend flour farinograph properties while enhancing the gas release during dough fermentation. Under the same addition ratio, the irradiated blend flours showed higher expansion height, gas release, cavitation time, and gas retention coefficient than the control flours. Also, irradiated blend flours retained a gluten network at a higher addition rate (20 %). Moreover, the irradiated blend flours were optimized at 10 % as its pasting and thermal properties were improved. Notably, this ameliorating effect promotes a decrease in hardness and chewiness and an increase in cohesion of the bread cores, presenting better textural attributes and delaying the aging rate during storage. The findings are instructive for applying EBI technology in the manufacture and quality improvement of mixed grain breads and open a new research avenue for processing sorghum staple foods.

The Conversion and Degradation of Sulphaguanidine under UV and Electron Beam Irradiation Using Fluorescence.

The work presents a spectral-luminescent study of the sulfaguanidine transformation in water under a pulsed e-beam and UV irradiation of an UVb-04 bactericidal mercury lamp (from 180 to 275nm), KrCl (222nm), XeBr (282nm) and XeCl (308nm) excilamps. Fluorescent decay curves have been used in our analysis of the sulfaguanidine decomposition. The conversion of antibiotic under e-beam irradiation for up to 1min was more than 80%, compared with UV radiation: UVb-04-26%, XeBr - 20%. KrCl and XeCl - about 10%. At the end of 64min of irradiation with UVb-04 and XeBr lamps, the conversion was 99%. During irradiation with these lamps, sulfaguanidine almost completely decomposed and passed into the final fluorescent photoproducts. After e-beam irradiated at the end of 13min the decrease in sulfaguanidine was 93%. At the same time, the formation of sulfaguanidine transformation products was minimal compared to UV irradiation. The effect of UV irradiation and a powerful e-beam on the decomposition mechanisms of sulfaguanidine are significantly different, which is manifested in various changes in the absorption and fluorescence spectra.

Revealing the effects of electron beam irradiation on the structural, optical, thermal, and dielectric properties of PVC/Ag2WO4 nanocomposite films

Herein, rod-like shape of Ag2WO4 was synthesized using the co-precipitation approach. These rods were mixed with PVC using the solution casting process to create a PVC/Ag2WO4 nanocomposite film. The effect of exposing the PVC/Ag2WO4 nanocomposite film to varying doses of the electron beam (E-beam) irradiation (0, 25, 50, and 100) kGy on its structural, optical, thermal, electric modulus, complex impedance, and dielectric properties was investigated. XRD results showed that Ag2WO4 has mixed phases. The optical properties have been addressed. The thermal evaluations were performed at three distinct heating rates: 6, 8, and 10 °C/min. In the same context, the thermal activation energy (Ea) of the unirradiated PVC/Ag2WO4 nanocomposite films increased from 12.89 to 31.17 kJ/mol with the increase in E-beam irradiation doses. As a result, E-beam irradiation reduces the values of the real (ɛ′) and imaginary (ε″) components of PVC/Ag2WO4 nanocomposite films. The electric modulus analyses showed that the magnitude of the grain capacitance increased as the E-beam doses increased, while the magnitude of the grain boundary capacitance exhibited a decreasing trend. Meanwhile, a progressive reduction in the diameter of the two semicircular arcs for complex impedance analyses was observed as the doses of E-beam irradiation increase.