Electron Beam Dynamics Research Articles

Simulation of the impact of an additional corrugated structure impedance on the bursting dynamics in an electron storage ring

In the case of a single-digit picosecond bunch length, synchrotron light sources produce intense coherent radiation up to the THz range. The reduction of the bunch length by lowering the momentum compaction factor (low-α) gives rise to the microbunching instability, which is on the one hand a crucial roadblock in the x-ray range during to the resulting effective bunch lengthening, but on the other hand also an opportunity for the generation of intense THz radiation if it can be controlled appropriately. In the KIT storage ring KARA (Karlsruhe Research Accelerator), two parallel plates with periodic rectangular corrugations are planned to be installed as a proof of principle in an electron storage ring. These plates create an additional longitudinal impedance based on their geometry, which can affect the beam dynamics. The resulting impedance manipulation will be used to study and control the longitudinal electron beam dynamics and the emitted coherent synchrotron radiation. This paper presents the results of systematic studies in simulation of the impact of additional corrugated plate impedances on the longitudinal beam dynamics using the example of the KARA storage ring. If the periodicity of the wake function of the corrugated plates matches the size of the substructures in the longitudinal bunch profile, the instability threshold can be effectively manipulated. This extends intense THz radiation to different beam current regimes. Published by the American Physical Society 2024

Analysis of RF modes in an in-vacuum undulator

Electron storage rings commonly use in-vacuum undulators (IVUs) consisting of magnet arrays positioned closely above and below the electron beam to create a bright, tunable and broad spectral range with narrow peaks. These devices present several challenges to the electron beam dynamics since the magnets come within a few millimetres of the beam and a vacuum chamber around the magnets results in discontinuities in the otherwise smooth chamber. This paper analyzes the radio frequency (RF) eigenmodes that exist in the IVU chamber which have been observed at other facilities and may excite beam instabilities. An equivalent RF circuit for the IVU confirms the TEM-nature of the eigenmodes. To eliminate the problematic modes induced in IVU device that may lead to beam instabilities, a conceptual solution is proposed and initial simulations are presented.

Dynamics of JET runaway electron beams in D2-rich shattered pellet injection mitigation experiments

Abstract The publication provide further insights into the dynamics of JET runaway electron (RE) beams mitigated by D2-rich shattered pellet injection (SPI) (Reux et al 2022 Plasma Phys. Control. Fusion 64 034002). Multi-diagnostic analyses show that mechanisms causing continuous RE losses and energy transfer from hot electrons to cold background plasma can act before the SPI. After the SPI, measurements are compatible with a reduction of the maximum energy and pitch angle of the RE distribution while the population of supra-thermal electrons increases. The RE population growth is likely due to electron avalanche. Dark island-like pattern chains, characterised by an integer poloidal mode number and a certain minor radius, are identified in the JET RE beam synchrotron radiation videos. The synchrotron island dynamics is studied via a newly developed computer vision code (Sommariva and Silburn https://c4science.ch/source/pSpiPTV/). The radial motion of synchrotron island chains is found to be consistent with the most plausible time evolution of the radial current density profile compatible with both the RE synchrotron videos and the total RE current time trace. Similarly, correlations are identified between the temporal progression of the synchrotron islands poloidal rotation frequency and sudden MHD relaxation events. Loss-of-RE events probably caused by non-linear interactions between synchrotron islands are observed for the first time. Experimental evidences suggest that synchrotron islands are possibly related to the existence of magnetic islands which may lead to the development of new RE beam mitigation strategies.

Time Profile Study of Type III Solar Radio Bursts Using Parker Solar Probe

Solar type III radio bursts are crucial indicators of energetic electron activity in the solar corona and interplanetary space. Our assessment of 43 interplanetary type III bursts, recorded by the FIELDS instrument on board the Parker Solar Probe during Encounters 05 to 11, has led to significant and complex findings. We have analyzed time profile features across a frequency range of 19–0.5 MHz, revealing dependencies on frequency and providing insights into duration, burst speeds, bandwidths, and drift rates. This novel analysis has unveiled a spectral index of −0.63 ± 0.04 for rise, −0.69 ± 0.03 for decay time, and −0.68 ± 0.03 for the total duration. We have determined the average electron beam velocities for front, middle, and back as 0.15c, 0.13c, and 0.08c, respectively. Our findings show that faster electron beams generate emissions with shorter duration. The average ratio of the front-to-back velocity is 1.87, and the ratio of front-to-middle velocity is 1.23. We have also discovered a strong relationship between burst duration with rise, peak, and decay times, particularly pronounced with decay time (correlation coefficient = 0.95). This indicates that the entire temporal profile, including rise, peak, and decay phases, collectively contributes to event duration and is not solely influenced by external factors like plasma conditions or electron beam dynamics but also by internal burst processes. These complex findings shed light on the physical mechanisms governing burst dynamics, revealing intricate interactions between electron beam characteristics and observed temporal and spectral traits of type III solar radio bursts.

Laser polarization control of ionization-injected electron beams and x-ray radiation in laser wakefield accelerators

In this paper, we have studied the influence of laser polarization on the dynamics of the ionization-injected electron beams, and subsequently, the properties of the emitted betatron radiation in laser wakefield accelerators (LWFAs). While ionizing by strong field laser radiation, the generated photo-electrons carry a residual transverse momentum in excess of the ionization potential via the above threshold ionization (ATI) process. This ATI momentum explicitly depends on the polarization state of the ionizing laser and eventually governs the dynamics of the electron beam trapped inside the wake potential. In order to systematically investigate the effect of the laser polarization, here, we have employed complete three-dimensional particle-in-cell simulations in the nonlinear bubble regime of the LWFAs. We focus, in particular, on the effects the laser polarization has on the ionization injection mechanism, and how these features affect the final beam properties, such as beam charge, energy, energy spread, and transverse emittance. We have also found that as the laser polarization gradually changes from linear to circular, the helicity of the electron trajectory, and hence the angular momentum carried by the beam, increases significantly. Studies have been further extended to reveal the effect of laser polarization on the radiation emitted by the accelerated electrons. The far-field radiation spectra have been calculated for the linear and circular polarization states of the laser. It has been shown that the spatial distributions and the polarization properties (Stokes parameters) of the emitted radiation in the above two cases are substantially different. Therefore, our study provides a facile and efficient alternative to regulate the properties of the accelerated electron beams and x-ray radiation in LWFAs, utilizing ionization injection mechanism.

Characteristics of the Alfvénic activity during the current quench in ASDEX Upgrade

ASDEX Upgrade has developed multiple massive gas injection (MGI) scenarios to investigate runaway electron (RE) dynamics. During the current quench of the MGI induced disruptions, Alfvénic activity is observed in the 300–800 kHz range. With the help of a mode tracing algorithm based on Fourier spectrograms, mode behaviour was classified for 180 discharges. The modes have been identified as global Alfvén eigenmodes using linear gyrokinetic MHD simulations. Changes in the Alfvén continuum during the quench are proposed as explanation for the strong frequency sweep observed. A systematic statistical analysis shows no significant connection of the mode characteristics to the dynamics of the subsequent runaway electron beams. In our studies, the appearance and amplitude of the modes does not seem to affect the potential subsequent runaway beam. Beyond the scope of the 180 investigated dedicated RE experiments, the Alfvénic activity is also observed in natural disruptions with no RE beam forming.

Electron beam analysis and sensitivity studies for the EuPRAXIA@SPARC_LAB RF injector

The interest in plasma-based accelerators as drivers of user facilities is growing worldwide thanks to their compactness and reduced costs. The EuPRAXIA@SPARC_LAB collaboration is preparing a technical design report for a multi-GeV plasma-based accelerator with outstanding electron beam quality to pilot an X-ray FEL, the most demanding in terms of beam brightness. The beam dynamics has been studied aiming to a reliable operation of the RF injector to generate a so-called comb-beam with 500 MeV energy suitable as driver of the Beam-driven Plasma Wakefield Accelerator. A case of interest is the generation of a trailing bunch with 1 GeV energy, less than 1 mm-mrad transverse emittance and up to 2 kA peak current at the undulator entrance. The comb-beam is generated through the velocity bunching technique, an RF compression tool that enables high brightness beams within relatively compact machine. Since it is based on a rotation of the beam phase space inside the external RF fields, it could be particularly sensitive to amplitude and phase jitters in the RF injector. The electron beam dynamics and the machine sensitivity to the possible jitters are presented in terms of effect on the beam quality so to provide the basis for the jitter tolerances.

Advanced Studies for the Dynamics of High Brightness Electron Beams with the Code MILES

High brightness electron beams enable a wide spectrum of applications ranging from short wavelength radiation sources to high gradient wakefield acceleration. The rich dynamics that are intrinsic in charged particles accelerated in complex systems require a careful description in the analysis and design of a given machine, particularly regarding its stability. Numerous computer codes are in use by the accelerator community for such purposes. In particular, MILES is a simple tracking code we have developed that allows fast evaluations of collective effects in RF linacs. In this paper we extend the simple models previously developed to describe specific, diverse applications that can benefit from the fast simulation tools developed in MILES. Examples of this kind include particle driven acceleration schemes in a plasma where driver and witness beams propagate in the “comb” pulse-train configuration. Specifically, we investigate the self-induced fields excited within the X-band rf-linac stage of EuPRAXIA@SPARC_LAB. Further, we discuss additional advanced topics such as resistive wall wakefield effects in planar FEL undulators and their impact on the radiation emitted.

Emittance Growth Study of an Electron Beam in a Double-Alpha Magnet Compressor Used in an Inverse Compton Scattering X-Ray Source

An Inverse Compton Scattering (ICS) X-ray source is under development at the ELSA (Electrons Laser X-Sources and Applications) electron RF linac of CEA DAM (Commissariat à l’Energie Atomique et aux Energies Alternatives, Direction des Applications Militaires). X-rays are emitted by the interaction of 30 MeV electron bunches with Nd:YAG laser pulses. The electron bunches duration is 30 ps rms before compression in two alpha magnets. In such a system, electron trajectories are curved with a short radius, resulting in a noticeable degradation of the beam emittance. In the specific case of strongly curved trajectories, the straight trajectory and beam shape assumptions used for space charge calculation in most simulation codes are questionable. Two different approaches to the simulation of electron beam dynamics within the alpha magnets are compared. A specific method to deal with changes from the reference particle frame to the laboratory reference frame, which does not imply any trajectory and beam shape assumptions, is proposed. Calculation results are presented. Along with an important emittance growth, they show that more physical effects can be taken into account in the latter simulation.

PiC/MC-simulation of a low-pressure discharge in helium initiated by a relativistic electron beam in a coaxial chamber with a magnetic cusp

A gas discharge is simulated and numerically studied. The discharge is excited by a tubular relativistic electron beam in gaseous helium in a coaxial gas-discharge chamber. A magnetic field in the form of a cusp was imposed on the chamber. The code based on the PiC/MC-method was used. Electron beam dynamics, time evolution of phase portraits of particles, physical parameters, and spatial-time characteristics of plasma were calculated. It is shown that a dense plasma appears in the cavity under the action of an electron beam in the form of a thin-walled tube of a large length; its concentration can be nHe+≈2×1010 cm−3. At the same time, it turned out that plasma is considerably non-uniform in length; its denser part corresponds to the parts where beams stop. Time dependence of the charge compensation of electrons on the helium atom concentration in the chamber was calculated. The dependence turned out to be decreasing since the rate of the discharge development is increasing with the growth of the helium pressure in the cavity.

Effects of a 4.3T superconducting wiggler on the electron beam optics and dynamics at NSLS-II

A superconducting wiggler (SCW) with a peak field of 4.3 T has recently been installed at NSLS-II. The wiggler generates a high-flux X-ray beam with a photon energy range from 20 keV to 200 keV for the High Energy Engineering X-ray Scattering beamline. This device induces significant distortions in the electron beam orbit and optics. We have corrected these adverse effects using feed-forward tables. The effects of the SCW on the electron beam emittance, energy spread, and bunch length were calculated and measured. The beam-induced heating of the cryogenic vacuum chamber was also studied. Finally, the superconducting wiggler has been commissioned for user operations.

Оптимизация полосы пропускания в лампе бегущей волны О-типа террагерцового диапазона

For developing terahertz O-type traveling wave tube amplifiers, as a rule, models are used that take into account only interaction of electron beam with electromagnetic wave in slow-wave system, without considering influence of areas occupied by electron gun and collector on these processes. However, if resonance occurs within volumes occupied by electron gun and collector, then this may lead to distortion of the slow-wave system bandwidth, thereby degrading the device performance. Reflectors using can significantly improve this situation, as thanks to reflectors, electromagnetic waves don't pass inside these areas, and absorbing layer inside them suppresses the resonance possibility. As a result, the device becomes more stable and efficient as an electromagnetic wave amplifier. This paper presents the numerical simulation results of processes in terahertz TWT model, including the entire device volume without exceptions, based on the Finite-Difference Time-Domain (FDTD) method for Maxwell equations and the Particle-In-Cells (PIC) method for calculating electron beam dynamics.

One-dimensional longitudinal space charge calculation based on integrated green function approach

For fast longitudinal electron beam dynamics study or optimization in an x-ray free electron laser (FEL) linear accelerator, the one-dimensional longitudinal space charge (1D LSC) impedance, assuming a round cylinder beam with uniform transverse distribution is extensively used in both analytical analysis and numerical simulation. In this paper, instead of employing the impedance model in the frequency domain, we directly calculate the longitudinal electric field by convolving the longitudinal beam density with the slice green function, i.e., the longitudinal electric field generated by a slice beam. For high-energy electron beam, the slice green function rapidly diminishes to zero within a distance significantly smaller than the bunch length. In order to resolve the sharp variation, we report on a fast and high-precision method by applying the integrated green function (IGF) approach to compute the 1D LSC field numerically with few grid points, therefore, providing us with an alternative approach to the impedance model.

MEPhI’s option of lab scale Compton source

A development and construction of comparatively cheap and compact (several meters scale) X-ray sources is possible with the help of inverse Compton backscattering of laser photons on an electron bunch. Such sources can be used in the field of materials science (new materials, diagnostics of nanostructures at the atomic level), research of nano- and biosystems, medicine and pharmacology (new drugs R&D), physics and chemistry of fast-flowing processes (burning, explosion). It is suggested that compact storage synchrotron will operate with normal conducting S-band top-up linac. Linac will provides bunches with tunable energy in the range of 20– 60 MeV to generate the photon flux with tunable energy [1, 2]. The use of a storage ring provides the following advantages: comparatively high average intensity of the generated photon flux, high brightness, photon beam energy tuning in a wide range, high degree of monochromaticity and coherence of the generated photons. There are current results of the design of a compact storage ring for generating the photons in the energy range of 5-45 keV and investigations of the development of relativistic picosecond electron beam dynamics instabilities in the report.

Characteristics of betatron radiation in AWAKE Run 2 experiment

The oscillating relativistic electrons in the accelerating/focusing wakefields of plasma accelerators emit electromagnetic radiation known as betatron radiation (BR). The proton-driven plasma wakefield acceleration has been demonstrated in the Advanced Wakefield Experiment (AWAKE) at CERN; however, its accompanying radiation emission is less explored compared with those in the laser- and electron beam-driven plasma accelerators. In this paper, a detailed simulation study of BR in the AWAKE is presented. Considering the new set-up of the AWAKE Run 2 (2021–), the radiation emission from both the witness electron beam and the seeding electron beam is investigated using particle-in-cell simulations. The influence of radial size mismatch and misaligned off-axis injection on the witness beam dynamics, as well as the spectral features of the relevant BR are studied. These non-ideal electron injections are likely to occur in experiment. The proton self-modulation stage is also investigated with a close look at the seeding electron beam dynamics and its BR. As a footprint of the emitting particles, BR can provide valuable information about the beam dynamics. Some practical challenges to implement the betatron diagnostic in the AWAKE Run 2 experiment are also addressed.

Development of a custom-made 2.8 T permanent-magnet dipole photon source for the ROCK beamline at SOLEIL.

In August 2021, the SOLEIL storage ring was restarted after the summer shutdown with a new bending magnet made entirely of permanent magnets. Producing a magnetic field of 2.8 T, it replaced one of the 32 electromagnetic dipoles (magnetic field of 1.7 T) of the ring to allow the ROCK beamline to exploit more intense photon fluxes in the hard X-ray range, thus improving the time resolution performances of the beamline for experiments carried out above 20 keV. The reduction of the new dipole magnetic gap required to produce the higher field has led to the construction and installation of a new vacuum vessel. The realization of the new dipole with permanent magnets was a technological feat due to the very strong magnetic forces. The permanent-magnet assembly required dedicated tools to be designed and constructed. Thanks to accurate magnetic measurements, a precise modelization of the new dipole was performed to identify its effects on the electron beam dynamics. The first measurements carried out on the ROCK beamline have highlighted the expected increase in photon flux, and the operation performances remain unchanged for the other beamlines. Here, the major developments and results of this innovative project are described in terms of technology, electron beam dynamics and photon beam performance on the ROCK beamline.

Measurement of femtosecond dynamics of ultrafast electron beams through terahertz compression and time-stamping

Visualizing ultrafast dynamics at the atomic scale requires time-resolved characterization with femtosecond temporal resolution. For fully relativistic electron bunch probes, existing techniques for single-shot ultrafast electron diffraction (UED) are limited by the achievable electron probe bunch length, charge, and timing jitter. We present the first experimental demonstration of dual-fed THz-driven compression and time-stamping that enables electron probes with improved temporal resolution. This technique utilizes two counter-propagating quasi-single-cycle THz pulses generated from two OH-1 organic crystals coupled into an optimized THz compressor structure. We demonstrate electron bunch compression and time-of-arrival jitter suppression by a factor of 3 paving the way toward unique opportunities for UED time-resolved measurements.

All-metal wakefield accelerator: Two-dimensional periodic surface lattices for charged particle acceleration

Interest in ``all-metal'' surface periodic structures to control charged particle beam dynamics and properties, and to generate coherent radiation in the THz frequency range has recently risen exponentially. While such structures have the benefits of metal, they are capable of providing similar properties to a dispersive dielectric. All-metal structures allow good temperature and space charge management. Transportation of high energy charge particle beams in the vicinity of the structure without risking material degradation makes them very attractive for particle acceleration and terahertz radiation generation applications. Here, the results of theoretical studies (via numerical modeling) of the electron beam dynamics and wakefield excitation and evolution along the cylindrical two-dimensional periodic surface structure will be presented, and the properties of the wakefields generated will be discussed. The wakefield acceleration of the witness bunch in the potential reaching $1\text{ }\text{ }\mathrm{GV}/\mathrm{m}$ will be demonstrated. The challenges will be identified and discussed, and the concept of the cascade accelerator based on such all-metal wakefield accelerator (AMWA) structures will be presented.

Carrier-envelope phase controlled dynamics of relativistic electron beams in a laser-wakefield accelerator

In laser-wakefield acceleration, an ultra-intense laser pulse is focused into an underdense plasma in order to accelerate electrons to relativistic velocities. In most cases, the pulses consist of multiple optical cycles and the interaction is well described in the framework of the ponderomotive force where only the envelope of the laser has to be considered. But when using single-cycle pulses, the ponderomotive approximation breaks down, and the actual waveform of the laser has to be taken into account. In this paper, we use near-single cycle laser pulses to drive a laser-wakefield accelerator. We observe variations of the electron beam pointing on the order of 10 mrad in the polarisation direction, as well as 30% variations of the beam charge, locked to the value of the controlled laser carrier-envelope phase, in both nitrogen and helium plasma. Those findings are explained through particle-in-cell simulations indicating that low-emittance, ultra-short electron bunches are periodically injected off-axis by the transversally oscillating bubble associated with the slipping carrier-envelope phase.

Submacropulse electron-beam dynamics correlated with higher-order modes in a Tesla-type cryomodule

Experiments were performed at the Fermilab Accelerator Science and Technology (FAST) facility to elucidate the effects of long-range wakefields (LRWs) in TESLA-type superconducting rf cavities. In particular, we investigated the higher-order modes (HOMs) generated in the eight cavities of a cryomodule (CM) due to off-axis steering with correctors located ~4 m upstream of the CM. We have observed correlated submacropulse centroid slews of a few-hundred microns and centroid oscillations at ~240 kHz in the rf BPM data after the CM. The entrance energy into the CM was 25 MeV, and the exit energy was 100 MeV with 125 pC/b and 400 pC/b in 50-bunch pulse trains. These experimental results were evaluated for machine learning training aspects which will be used to inform the commissioning plan for the Linac Coherent Light Source-II injector CM.