Dynamic Gratings Research Articles

Dynamic surface gratings for optical encryption: A simple approach based on azobenzene photoisomerization and solvent engineering

Dynamic diffraction gratings are optical devices that allow for non-mechanical, non-contact and remote on-demand control, and have garnered significant interest in optical encryption. Azobenzene materials are ideal materials for developing dynamic gratings owing to the advantages of fast photo isomerization and good reversibility. It is still challenging to precisely fabricate ordered periodic gratings on the surfaces of azobenzene materials. Here, controllable dynamic grating patterns were successfully fabricated by mask exposure and solvent engineering on azobenzene polyamide acid (PAA-Azo)-solvent system. The movement and mass migration of polymer chains can be regulated by modulating the intermolecular hydrogen bonding and free volume based on different solvents and solvent contents within the system, resulting in the formation of surface gratings with customizable morphology and light-splitting ability. Finally, by regulating the periodicity and amplitude of gratings, colorful dynamic patterns were obtained to monitor the expiration of light-sensitive and short shelf-life products, based on the azobenzene polyamide acid (PAA-Azo)-solvent system. This work provides a new and simple approach for controllable preparation of high-regularity and high-performance dynamic gratings.

Broadband tunable single-frequency Yb-doped fiber laser with dual ring subcavity and Sagnac ring filter

We demonstrate a broadband tunable ultra-narrow linewidth single-frequency (SF) Yb-doped fiber laser (YDFL). A dual ring subcavity (DRS) as a filtering component to eliminate the dense longitudinal mode inherent in YDFL and theoretically analyzed its filtering characteristics. By inserting a 0.8 m unpumped polarization-maintaining Yb-doped fiber in the Sagnac ring, a dynamic narrowband grating (DNG) based on the saturable absorption (SA) effect is constructed to ensure SF laser output over the entire wavelength tuning range. We achieve a wide wavelength tunable SF laser output in the range of ∼74 nm, covering 1021.06 nm to 1094.98 nm. The laser has an optical signal-to-noise ratio (OSNR) of more than 62.5 dB, a slope efficiency of 3.57 %, and an ultra-narrow linewidth of 622 Hz over the entire tunable range. In addition, the stability of the wavelength and power fluctuations below 0.018 nm and 0.67 dB, respectively. This tunable SF fiber laser has a compact structure, lower cost, and excellent performance, and is expected to be used in the fields of coherent communications, precision metrology, and so on.

Observation of a Brillouin dynamic grating in silicon nitride waveguides

Brillouin enhanced four wave mixing in the form of a Brillouin dynamic grating (BDG) enables a uniquely tunable filter whose properties can be tuned by purely optical means. This makes the BDG a valuable tool in microwave photonics (MWP). BDGs have been studied extensively in fibers, but the only observation in an integrated platform required exotic materials. Unlocking BDG in a standard and mature platform will enable its integration into large-scale circuits. Here, we demonstrate the first observation of a BDG in a silicon nitride (Si3N4) waveguide. We also present a new and optimized design, which will enhance the BDG response of the waveguide, unlocking the path to large-scale integration into MWP circuits.

Self-injection locked low-noise Brillouin random fiber laser via dynamic fiber grating for QAM coherent communication

A low-noise Brillouin random fiber laser (BRFL) based on dynamic fiber grating (DFG)-assisted self-injection locking (SIL) as a laser carrier for coherent communication is proposed and experimentally demonstrated. The utilization of the DFG-based SIL basically guarantees an innovative purification of ultra-narrow-linewidth laser radiation after the removal of residual random modes from the gain competition, enabling unprecedented long-term frequency-stabilized coherent lasing resonance over a record of 30 s. Consequently, the relative intensity noise of the generated Stokes random laser is significantly suppressed by ∼20 dB, and the frequency/phase noise imposed by random mode hopping is additionally mitigated. Meanwhile, stimulated Brillouin scattering and randomly distributed Rayleigh scattering along the kilometer-long single-mode fiber further suppress laser frequency/phase noise, benefiting the ultra-narrow laser linewidth of 450 Hz. As a proof-of-concept, an 8-Gbaud (32 Gb/s) 16-quadrature amplitude modulation transmission based on the proposed self-injection locked low-noise BRFL as the laser carrier is demonstrated, achieving a low bit error rate of 3.02×10−5. The impact of the laser noise on coherent communication is systematically investigated, highlighting the potential in high-capacity coherent communication.

Ultrafast Solid-State Electrochemical Imprinting Utilizing Polymer Electrolyte Membrane Stamps for Static/Dynamic Structural Coloration and Letter Encryption.

Micro and nanopatterned surfaces hold potential for various applications, such as wettability control, antibiofouling, and optical components. However, conventional patterning processes are characterized by complexity, high costs, and environmental burdens because of the use of resists. Therefore, this paper proposes facile and ultrafast electrochemical imprinting employing a polymer electrolyte membrane (PEM) stamp for achieving micro and nanoscale patterning on Si surfaces. The solid-state electrochemical process efficiently generates oxide and hydrated oxide (Si-OH) patterns within several seconds at room temperature in a dry ambient environment. The formed oxide pattern can be employed as an etching mask to prepare diffraction gratings with diverse high-resolution (≈100nm) patterns utilizing the dry PEM stamp. The resulting oxide pattern on the Si surface exhibits instantaneous structural coloration upon exposure to humid air, attributable to the formation of a water microdroplet array on the oxide pattern. The oxide pattern is successfully applied for dynamic diffraction grating and letter encryption. The proposed solid-state electrochemical oxidation scheme based on a PEM stamp, which eliminates the need for liquid electrolyte and resist, represents a simple and ultrafast process with a time cost of a few seconds, characterized by low processing costs and environmental impact.

All-fiber broadband spectral acousto-optic modulation of a tubular-lattice hollow-core optical fiber.

We demonstrate a broadband acousto-optic notch filter based on a tubular-lattice hollow-core fiber for the first time to our knowledge. The guided optical modes are modulated by acoustically induced dynamic long-period gratings along the fiber. The device is fabricated employing a short interaction length (7.7 cm) and low drive voltages (10 V). Modulated spectral bands with 20 nm half-width and maximum depths greater than 60% are achieved. The resonant notch wavelength is tuned from 743 to 1355 nm (612 nm span) by changing the frequency of the electrical signal. The results indicate a broader tuning range compared to previous studies using standard and hollow-core fibers. It further reveals unique properties for reconfigurable spectral filters and fiber lasers, pointing to the fast switching and highly efficient modulation of all-fiber photonic devices.

Manipulation of path state based on spatiotemporal dielectric metasurface.

In this work, a spatiotemporal metasurface is proposed to manipulate the path of photons flexibly. The spatial modulation is induced by the rectangle silicon units aligned on silica in a manner with a phase gradient only for y-polarized photons, and the temporal modulation is contributed by the pumps of constructing Kerr dynamic gratings. By quantizing designed metasurfaces, the analytical solutions of output photon states can be derived correspondingly. Reversal design could be implemented by tailoring the profile of higher harmonics to infer the intensity of pumps, size of meta-atoms, and initial state. The path-polarization entanglement and correlations of output photons are realized, and then a CNOT gate is obtained by utilizing the deflection of the photon path. This work provides a scheme to deal with the spatiotemporal metasurfaces and expands the applications of metasurfaces in the quantum realm.

High-sensitivity Simultaneous Demodulation of Multi-parameters in Polarization-maintaining Fibers Based on Brillouin Dynamic Gratings

High-sensitivity Simultaneous Demodulation of Multi-parameters in Polarization-maintaining Fibers Based on Brillouin Dynamic Gratings

Distributed phase-matching measurement for dynamic strain and temperature sensing based on stimulated Brillouin scattering enhanced four-wave mixing

A Brillouin dynamic grating (BDG) can be used for distributed birefringence measurement in optical fibers, offering high sensitivity and spatial resolution for sensing applications. However, it is quite a challenge to simultaneously achieve dynamic measurements with both high accuracy and high spatial resolution. In this work, we propose a sensing mechanism to achieve distributed phase-matching measurement using a chirped pulse as a probe signal. In BDG reflection, the peak reflection corresponds to the highest four-wave mixing (FWM) conversion efficiency, and it requires the Brillouin frequency in the fast and slow axes to be equal, which is called the phase-matching condition. This condition changes at different fiber positions, which requires a range of frequency injection for the probe wave. The proposed method uses a chirped pulse as a probe wave to cover this frequency range associated with distributed birefringence inhomogeneity. This allows us to detect distributed phase matching for birefringence changes that are introduced by temperature and strain variations. Thanks to the single shot and direct time delay measurement capability, the acquisition rate in our system is only limited by the fiber length. Notably, unlike conventional BDG spectrum recovery-based systems, the spatial resolution here is determined by both the frequency chirping rate of the probe pulse and the birefringence profile of the fiber. In the experiments, an acquisition rate of 1 kHz (up to fiber length limits) and a spatial resolution of 10 cm using a 20 ns probe pulse width are achieved. The minimum detectable temperature and strain variation are 5.6 mK and 0.37 με along a 2 km long polarization-maintaining fiber (PMF).

Observation of Q-switched and continuous wave regimes in Er-doped fiber lasers incorporating a dynamic population grating

Dynamic population gratings (DPGs) in rare-earth doped fibers are prevalent devices in fiber lasers for the production of single-longitudinal-mode emission and wavelength self-sweeping regimes. This study presents a transition from Q-switched state to continuous wave (CW) state, accompanying irregular mode-hopping, in an erbium-doped fiber laser with a heavily-doped DPG centered at 1549.95 nm. Our results demonstrate that the transition between these two states can be achieved by adjusting the pump power. The repetition frequency of the Q-switched pulse increases monotonically with the increasing pump power, while the pulse duration initially narrows and then expands because the reduced peak intensity weakens the nonlinear effect. Additionally, modulation peaks are evident on both the Q-switched pulse train and the CW background, which are induced by the irregular mode-hopping caused by the DPG. Furthermore, we observe that the central wavelength fluctuates within a range of 0.05 nm. These results provide valuable insight into the DPG effect in heavily-doped fibers.

1.2 W single-frequency Tm3+/Ho3+ co-doped fiber oscillator at 2050 nm.

In this Letter, a watt-level single-frequency fiber oscillator at 2050 nm was demonstrated for the first time, to the best of our knowlegde, in a linear laser cavity with a piece of an un-pumped Tm3+/Ho3+ co-doped fiber serving as a saturable absorber. With delicate optimization of mode filtering effect of the dynamic gratings formed in the saturable absorber, a maximum single-frequency laser output power of 1.2 W was achieved under a total bidirectional pump power of 5.8 W at 1570 nm, and the corresponding optical efficiency is 20.7%. This is, to the best of our knowledge, the highest power of a single-frequency fiber oscillator at the wavelength above 2 µm.

Laser beam array spot steering customized trajectories using the acousto-optic effect.

We demonstrate a proof of principle of a technique for array laser beam steering according to a generalized elliptical path, using the acousto-optic effect. We explore the dynamic trajectories of the diffraction orders of a Gaussian beam, diffracted by a dynamic 2D sinusoidal phase grating. The latter is generated by two crossed acoustic waves propagating in a transparent medium, giving rise to 2D dynamic sinusoidal refractive index variation. We particularly emphasize the case where the two crossed acoustic waves are modulated in frequency and have a phase difference. In such case, the resulting diffraction orders are dynamic and follow some particular trajectory's shapes, from linear and circular to generalized elliptical shapes. Inspired by Poincaré and Bloch spheres used to represent polarization and quantum states, we suggest the sphere volume trajectory shape to represent all trajectories' shapes of all diffraction orders.

High-Resolution Distributed Analysis on Brillouin Dynamic Grating by Differential Measurement and Matched Filtering

Improvement of spatial resolution in the distributed analysis on Brillouin dynamic grating (BDG) in a polarization-maintaining fiber (PMF) is demonstrated using a differential measurement (DM) scheme and a matched RF low-pass filter. The DM is applied to remove the reflection signals from uncorrelated positions, and a RF low pass filter optimized for a target spatial resolution is used to suppress the high-frequency common noise remaining in the BDG spectrum. In experimental confirmation distribution of the BDG spectra in a 1 km PMF is measured with a 5 cm spatial resolution, which is equal to the nominal spatial resolution determined by the synthesis of optical coherence function in the correlation-domain analysis system.

Opto-mechanical fiber sensing with optical and acoustic cladding modes

Optical fibers are an excellent sensor platform. However, the detection and analysis of media outside the cladding and coating of standard fibers represent a long-standing challenge: light that is guided in the single optical core mode does not reach these media. Cladding modes help work around this difficulty, as their transverse profiles span the entire cross-section of the fiber cladding and reach its outer boundary. In this tutorial, we introduce and discuss in detail two recent advances in optical fiber sensors that make use of cladding modes. Both concepts share optomechanics as a common underlying theme. First, we describe a spatially continuous distributed analysis using the optical cladding modes of the fiber. Light is coupled to these modes using Brillouin dynamic gratings, which are index perturbations associated with acoustic waves in the core that are stimulated by light. Unlike permanent gratings, which are routinely used to couple light with cladding modes, Brillouin dynamic gratings may be switched on and off at will and can be confined to short fiber sections at arbitrary locations in a random-access manner. Second, we present the extension of the cladding mode sensor concept to include acoustic rather than optical modes. The acoustic cladding modes may be stimulated and monitored by guided light in the single core mode, and their linewidths are modified by the elastic properties of surrounding media. The principles and analyses of both concepts are provided in detail, alongside examples of experimental setups and results.

High Spatial Resolution Sensing of Temperature and Strain Without Cross Sensitivity Based on Chaotic Brillouin Dynamic Grating

A distributed fiber-optic sensing system based on chaotic Brillouin dynamic grating (BDG) without cross-sensitivity of temperature and strain is proposed and experimentally demonstrated. The chaotic BDG is stimulated by interaction of two chaotic pump beams with a certain frequency difference along the slow axis of polarization-maintaining fiber (PMF) and detected by the continuous probe light along the fast axis. The generated chaotic BDG has the characteristic of single, permanent, and localized grating. The grating length is determined by the low coherence length of the chaotic laser, which ensures that the spatial resolution of the chaotic BDG sensing system can reach the centimeter scale. Two parameters, i.e., Brillouin frequency shift (BFS) and birefringence frequency shift (BireFS) are measured to achieve the temperature and strain simultaneous discrimination. In the experiment, a 2.3-cm spatial resolution non-cross-sensitivity measurement was demonstrated over a 100-m long PMF, where temperature and strain discriminative accuracy can reach 0.3 °C and 11 με, respectively.

Sub-kHz high-order mode Brillouin random fiber laser based on long-period fiber grating and distributed Rayleigh scattering in a half-open linear cavity.

We demonstrate a narrow-linewidth high-order-mode (HOM) Brillouin random fiber laser (BRFL) based on a long-period fiber grating (LPFG) and distributed Rayleigh random feedback in a half-open linear cavity. The single-mode operation of the laser radiation with sub-kilohertz linewidth is achieved thanks to distributed Brillouin amplification and Rayleigh scattering along kilometer-long single mode fibers whilst a few mode fiber-based LPFGs enable the transverse mode conversion among a broadband wavelength range. Meanwhile, a dynamic fiber grating (DFG) is embedded and incorporated to manipulate and purify the random modes, which hence suppresses the frequency drift resulting from random mode hopping. Consequently, the random laser emission with either high-order scalar or vector modes can be generated with a high laser efficiency of 25.5% and an ultra-narrow 3-dB linewidth of 230 Hz. Furthermore, the dependence of the laser efficiency and frequency stability on the gain fiber length are also experimentally investigated. It is believed that our approach could provide a promising platform for a wide range of applications such as coherent optical communication, high-resolution imaging, highly sensitive sensing, etc.

Quasi-periodic spectro-temporal pulse breathing in a femtosecond-pumped tellurite graded-index multimode fiber.

We report on the multidimensional characterization of femtosecond pulse nonlinear dynamics in a tellurite glass graded-index multimode fiber. We observed novel multimode dynamics of a quasi-periodic pulse breathing which manifests as a recurrent spectral and temporal compression and elongation enabled by an input power change. This effect can be assigned to the power dependent modification of the distribution of excited modes, which in turn modifies the efficiency of involved nonlinear effects. Our results provide indirect evidence of periodic nonlinear mode coupling occurring in graded-index multimode fibers thanks to the modal four-wave-mixing phase-matched via Kerr-induced dynamic index grating.

High spatial resolution Stokes metasurface based on three-pixel technology

A dynamically reconfigurable metasurface grating is proposed in this work based on the phase change material Ge2Sb2Te5 (GST). The metasurface grating keeps as the 0° polarizer that allows only x-polarized light to pass when the GST is in the crystalline state, and switches to the 90° polarizer (only y-polarized light passes through) while the GST transforms into the amorphous state. Furthermore, the circular polarization dichroism could be achieved using a double-layer metasurface consisting of this dynamic grating and a large broadband plasmonic quarter-wave plate. We can expect to achieve fully polarized detection with the ultra-high spatial resolution using only three components. In addition, we can obtain the largest bandwidth (300 nm) of the full Stokes large-image-element to date in the near infrared band by using the six-image-element technique with the crystalline phase GST.

Spectral Properties of Dynamic Population Gratings in Ytterbium-Doped Fibers

Spectral Properties of Dynamic Population Gratings in Ytterbium-Doped Fibers

Dynamic Optical Grating Based on a Photomechanical Molecular Crystal

AbstractOrganic photomechanical crystals transform molecular‐scale photoisomerization events into largescale crystal shape changes. The results in this paper demonstrate that this photomechanical motion can be harnessed to reconfigure reflective elements on the crystal surface to actively control light propagation. This is accomplished by using a single organic photomechanical crystal composed of 1,2‐bis(2,4‐dimethyl‐5‐phenyl‐3‐thienyl)‐3,3,4,4,5,5‐hexafluoro‐1‐cyclopentene, which undergoes a reversible ring‐open to ring‐closed photoisomerization. Electron beam lithography patterning followed by a sublimation development step leaves periodically positioned, 120 nm deep grooves that are coated with gold metal to form a reflective grating on the crystal surface. Under UV irradiation, expansion of the bulk crystal increases the grating period by ≈5% and changes the diffraction angle of a 633 nm probe laser beam by 0.7° (first order) and 1.3° (second order). The grating period change can be reversed by visible light exposure and repeated for multiple cycles. The crystal expansion and thus the diffraction angle can also be continuously tuned by controlling the duration of light exposure. Anisotropic crystal expansion and contraction due to molecular photoisomerization enables low‐power light sources to steer light beams continuously over a range of diffraction angles.