Dynamic Biaxial Tests Research Articles

The yielding behavior and plastic deformation of oxygen-free copper under biaxial quasi-static and dynamic loadings

This study investigated the yield behavior of oxygen-free copper under complex stress states and different loading rates. An optimized cruciform specimen and a novel electromagnetic biaxial split Hopkinson bar (EBSHB) were used to perform the dynamic biaxial tension tests at three different load ratios. The non-contact digital image correlation technique was adopted for strain measurement. Quasi-static and dynamic yield surfaces were obtained. Classical yield criteria, including the Tresca and von Mises yield criteria, were evaluated based on the experimental results. The von Mises criterion is found to provide better prediction of the yield surface under both quasi-static and dynamic loadings. The Johnson-Cook model from uniaxial test results provides a moderate prediction for experimental curves, while that from biaxial test results shows better prediction. Dynamic biaxial tests are proven necessary to acquire the constitutive models that can accurately describe the mechanical properties of copper under complex stress states.

Failure of short carbon-fiber-reinforced PEEK composites under high strain rate biaxial loading

The dynamic failure of short carbon fiber reinforced polyether-ether-ketone (SCFR-PEEK) composites under biaxial stresses was investigated in this paper. Cruciform specimens were loaded with a biaxial split Hopkinson tensile bar system, and a high-speed camera was utilized to record the deformation and failure processes. A nonlinear numerical model calibrated with dynamic uniaxial tests was used to estimate the stress in the cruciform specimen, in conjunction with strain fields from digital image correlation (DIC) of high-speed camera images. The failure of the cruciform specimen initiated inside the gauge section under all dynamic loading cases, and the numerical strain fields are in good agreement with the experimental ones. The dynamic failure envelope under biaxial stresses was successfully obtained, the failure strain decreased and failure stress increased with strain rate noticeably. The testing method developed here is also applicable for dynamic biaxial testing of many other composites.

Hip Capsular Closure: A Biomechanical Analysis of Failure Torque

Background: Hip capsulotomy is routinely performed during arthroscopic surgery to achieve adequate exposure of the joint. Iatrogenic instability can result after hip arthroscopic surgery because of capsular insufficiency, which can be avoided with effective closure of the hip capsule. There is currently no consensus in the literature regarding the optimal quantity of sutures upon capsular closure to achieve maximal stability postoperatively. Purpose/Hypothesis: The purpose of this study was to determine the failure torques of 1-, 2-, and 3-suture constructs for hip capsular closure to resist external rotation and extension after standard anterosuperior interportal capsulotomy (12 to 3 o’clock). Additionally, the degree of external rotation at which the suture constructs failed was recorded. The null hypothesis of this study was that no significant differences with respect to the failure torque would be found between the 3 repair constructs. Study Design: Controlled laboratory study. Methods: Nine pairs (n = 18) of fresh-frozen human cadaveric hemipelvises underwent anterosuperior interportal capsulotomy, which were repaired with 1, 2, or 3 side-to-side sutures. Each hip was secured in a dynamic biaxial testing machine and underwent a cyclic external rotation preconditioning protocol, followed by external rotation to failure. Results: The failure torque of the 1-suture hip capsular closure construct was significantly less than that of the 3-suture construct. The median failure torque for the 1-suture construct was 67.4 N·m (range, 47.4-73.6 N·m). The median failure torque was 85.7 N·m (range, 56.9-99.1 N·m) for the 2-suture construct and 91.7 N·m (range, 74.7-99.0 N·m) for the 3-suture construct. All 3 repair constructs exhibited a median 36° (range, 22°-64°) of external rotation at the failure torque. Conclusion: The most important finding of this study was that the 2- and 3-suture constructs resulted in comparable biomechanical failure torques when external rotation forces were applied to conventional hip capsulotomy in a cadaveric model. The 3-suture construct was significantly stronger than the 1-suture construct; however, there was not a significant difference between the 2- and 3-suture constructs. Additionally, all constructs failed at approximately 36° of external rotation. Clinical Relevance: Re-establishing the native anatomy of the hip capsule after hip arthroscopic surgery has been reported to result in improved outcomes and reduce the risk of iatrogenic instability. Therefore, adequate capsular closure is important to restore proper hip biomechanics, and postoperative precautions limiting external rotation should be utilized to protect the repair.

Studies of biaxial mechanical properties and nonlinear finite element modeling of skin.

The objective of this research is to conduct mechanical property studies of skin from two individual but potentially connected aspects. One is to determine the mechanical properties of the skin experimentally by biaxial tests, and the other is to use the finite element method to model the skin properties. Dynamic biaxial tests were performed on 16 pieces of abdominal skin specimen from rats. Typical biaxial stress-strain responses show that skin possesses anisotropy, nonlinearity and hysteresis. To describe the stress-strain relationship in forms of strain energy function, the material constants of each specimen were obtained and the results show a high correlation between theory and experiments. Based on the experimental results, a finite element model of skin was built to model the skin's special properties including anisotropy and nonlinearity. This model was based on Arruda and Boyce's eight-chain model and Bischoff et al.'s finite element model of skin. The simulation results show that the isotropic, nonlinear eight-chain model could predict the skin's anisotropic and nonlinear responses to biaxial loading by the presence of an anisotropic prestress state.

Dynamic bi-axial testing of woven composites

Thick panel glass/polymer composites are being considered as a structural component in ballistic armor. A new experimental technique has been developed to perform dynamic bi-axial testing on laminate composites. In-plane ultimate compressive strength of the composite is compared for various combinations of bi-axial stress and strain rate. Evolution of the damage in the composite and subsequent kink-band formation is studied by the use of high-speed photography and electron microscopy.

Structural damping of composites under sustained vibratory stresses

AbstractThe dynamic properties of a fiber‐reinforced composite under uniaxial sinusoidal stresses have been studied and the dynamic modulus and loss coefficients have been evaluated. Effects of fiber orientation to applied stress, the magnitude of static biaxial stresses, frequencies of fluctuating stresses and the temperature on the dynamic properties have been studied. The paper describes a dynamic biaxial testing machine specially developed for the measurement of dynamic properties of fiber‐reinforced materials for a low frequency range. Results indicate that the single laminate material displays very little damping. However, the multilaminate material reveals an appreciable damping that is dependent on the frequency of fluctuation of applied stress. The loss coefficient for the multilaminate material was found to decrease with frequency and was appreciably affected by fiber orientation, magnitudes of mean biaxial stresses, and temperature. Finally, an examination of data indicated that the time‐temperature equivalence hypothesis can be applied. Using this principle, master loss coefficient curves for an extended frequency range have been obtained.