Dummy Head Research Articles

Acoustic measurement around the pinna in the VHF region using a dummy head

We investigated the azimuth and vertical angle characteristics of head related transfer function (HRTF) at very high frequency region using head and torso simulator (HATS). The VHF sounds contain potential hazards for young people who can hear such sounds. Therefore, the relationship between hearing thresholds in very-high frequency (VHF) region and intensity of VHF sounds are very important for considering human impact. The former means sound pressure level (SPL) at eardrum, and the latter is SPL at center of two ears without a head. The difference between two SPLs means head-related transform function (HRTF). In this paper, we reported the HRTFs measured in VHF region for the azimuth and vertical angles by using a HATS. The complicated contour maps of HRTFs for angle and frequency show that the SPLs at eardrum in VHF region depend on among material, size and figure of a pinna.

Experimental Study of the Influence of Occupants on Speech Intelligibility in an Automotive Cabin

Adding occupants to an enclosed space often leads to perceptible changes in the sound field and, therefore, speech intelligibility; however, this issue has not yet been examined in automotive cabins. This study investigated the effect of occupants in an automotive cabin on SI. Binaural room impulse responses (BRIRs) were measured in an automotive cabin with an artificial mouth and dummy head under different speaker–listener position configurations and occupancy modes. Based on the measured BRIRs, the speech transmission index (STI) was determined, and subjective speech–reception thresholds (SRTs) in Mandarin Chinese were assessed. The results indicate that speech intelligibility mostly decreased slightly after adding additional occupants. In most cases, the occupants did not significantly affect speech intelligibility, with STI variations of no more than the just-noticeable difference and SRT variation within 1 dB. When the listener was in the back-right seat, the effect of the occupants on speech intelligibility could not be ignored, with STI variations of up to 0.07 and an SRT variation of 2 dB under different occupancy modes. In addition, the influence of front-row passengers on the speech intelligibility of rear-row listeners was extremely small, and vice versa. Furthermore, altering the distribution of occupants had an effect comparable to changing the number of occupants.

The Effect of Changing the Angle of the Passenger Car Seat Backrest on the Head Trajectories of the 50th Percentile Male Dummy.

The aim of the study is to compare the head displacement of the KPSIT C50 dummy during a frontal collision at a speed of 20 km/h, along with the change in the angle of the car seat backrest. Passenger car manufacturers recommend setting the backrest angle of the car seat between 100 and 125 degrees. It should be noted that the driver's position is of great importance in the event of a collision injury. In the event of a rear-end collision, the position of the headrest of the car seat is an element that affects the degree of the driver's injuries. In extreme cases, incorrect positioning of the headrest, even at low speed, can lead to serious injuries to the cervical spine and even death. The article is part of a large-scale study on low-speed crash testing. The research problem concerned the influence of the seat backrest angle on the head displacement during a low-speed collision. The article compares the displacement of the head of the KPSIT C50 dummy during a series of crash tests, where the angle of the car seat backrest was changed. On the basis of the research, it was found that the optimal angle of the car seat backrest is 110 degrees. In addition, a preliminary analysis of the displacements of the dummy's head showed a high risk of whiplash injury in people sitting in a fully reclined seat.

Training in the use of the water jet and cold atmospheric plasma jet for the decontamination of dental implants

ObjectivesClinical trials testing new devices require prior training on dummies to minimize the "learning curve" for patients. Dentists were trained using a novel water jet device for mechanical cleaning of dental implants and with a novel cold plasma device for surface functionalisation during a simulated open flap peri-implantitis therapy. The hypothesis was that there would be a learning curve for both devices.Materials and methods11 dentists instrumented 44 implants in a dummy-fixed jaw model. The effect of the water jet treatment was assessed as stain removal and the effect of cold plasma treatment as surface wettability. Both results were analysed using photographs. To improve treatment skills, each dentist treated four implants and checked the results immediately after the treatment as feedback.ResultsWater jet treatment significantly improved from the first to the second implant from 62.7% to 75.3% stain removal, with no further improvement up to the fourth implant. The wettability with cold plasma application reached immediately a high level at the first implant and was unchanged to the 4th implant (mean scores 2.7 out of 3).ConclusionA moderate learning curve was found for handling of the water jet but none for handling of the cold plasma.Clinical relevanceScientific rational for study: Two new devices were developed for peri-implantitis treatment (Dental water jet, cold plasma). Dentists were trained in the use of these devices prior to the trial to minimize learning effects.Principal findings: Experienced dentists learn the handling of the water jet very rapidly and for cold plasma they do not need much training.Practical implications: A clinical study is in process. When the planned clinical study will be finished, we will find out, if this dummy head exercise really minimised the learning curve for these devices.

Evaluating head impact intensities and accelerations using flexible wearable sensors for traumatic brain injury assessment

In response to the significant health threat posed by Traumatic Brain Injury (TBI) resulting from sudden collisions on the head, there is an urgent need for timely assessment and evaluation. With the wide applications of wearable devices in health monitoring, here we report a flexible and wearable smart headband based on a polyvinylidene fluoride (PVDF) sensor to evaluate the impact force and acceleration for TBI assessment. Based on the electromechanical coupling characteristics of PVDF, a lumped parameters model of an equivalent circuit was obtained by a system identification method, which accurately transforms the output signal of the PVDF sensor to the impact force for TBI assessment of focal brain damage. Besides, a drop tower was used to impose different impact intensity levels on a dummy head wearing the smart headband; the results (MSE< 0.018) of transformed impact force show the universal applicability of the model. Moreover, the correlation analysis results show that the impact force has a positive correlation (R>85 %) with impact acceleration at the head center of gravity, which enables the TBI assessment of diffuse brain damage. This smart headband can be used for real-time monitoring of human head impact and has excellent potential for application in medical and sports devices.

A study on the application of diffuse axonal multi-axis general evaluation for brain injury assessment in small overlap barrier crash test

PurposeHead injury criterion (HIC) companied by a rotation-based metric was widely believed to be helpful for head injury prediction in road traffic accidents. Recently, the Euro-New Car Assessment Program utilized a newly developed metric called diffuse axonal multi-axis general evaluation (DAMAGE) to explain test device for human occupant restraint (THOR) head injury, which demonstrated excellent ability in capturing concussions and diffuse axonal injuries. However, there is still a lack of comprehensive understanding regarding the effectiveness of using DAMAGE for Hybrid Ⅲ 50th percentile male dummy (H50th) head injury assessment. The objective of this study is to determine whether the DAMAGE could capture the risk of H50th brain injury during small overlap barrier tests. MethodsTo achieve this objective, a total of 24 vehicle crash loading curves were collected as input data for the multi-body simulation. Two commercially available mathematical dynamic models, namely H50th and THOR, were utilized to investigate the differences in head injury response. Subsequently, a decision method known as simple additive weighting was employed to establish a comprehensive brain injury metric by incorporating the weighted HIC and either DAMAGE or brain injury criterion. Furthermore, 35 sets of vehicle crash test data were used to analyze these brain injury metrics. ResultsThe rotational displacement of the THOR head is significantly greater than that of the H50th head. The maximum linear and rotational head accelerations experienced by H50th and THOR models were (544.6 ± 341.7) m/s2, (2468.2 ± 1309.4) rad/s2 and (715.2 ± 332.8) m/s2, (3778.7 ± 1660.6) rad/s2, respectively. Under the same loading condition during small overlap barrier (SOB) tests, THOR exhibits a higher risk of head injury compared to the H50th model. It was observed that the overall head injury response during the small overlap left test condition is greater than that during the small overlap right test. Additionally, an equation was formulated to establish the necessary relationship between the DAMAGE values of THOR and H50th. ConclusionIf H50th rather than THOR is employed as an evaluation tool in SOB crash tests, newly designed vehicles are more likely to achieve superior performance scores. According to the current injury curve for DAMAGE and brain injury criterion, it is highly recommended that HIC along with DAMAGE was prioritized for brain injury assessment in SOB tests.

Influence of virtual audio system on psychological restoration effects of soundscapes: Investigating water sounds of a Chinese classical garden

Various sound recording and reproduction methods were utilized to create virtual replicas of soundscapes and restoration effects of soundscapes were examined in studies. The reproduction quality of different virtual audio systems may impact the restoration effect of soundscapes. However, only a limited number of studies have conducted experiments to explore these influences. In this study, five water sounds from a traditional Chinese garden were recorded and reproduced using the monaural, binaural, and first-order Ambisonics technologies. The study evaluated the psychological restorative effects of both virtual and real-world soundscapes through the perceived restorativeness soundscape scale. Furthermore, the perceived realism and spaciousness of the virtual soundscapes were subjectively compared. The findings confirmed the relationship between fidelity and the restorative effects of virtual soundscapes. Binaural recording and playback using a dummy head and headphones proved to be the most authentic method for recreating restorative sound environments. Ambisonics also yielded relatively consistent rating scores compared to real-world cases, whereas the monaural scheme posed a risk of deteriorating the restoration effect of soundscapes.

Effect of sound-induced vibrations of the pinna on head-related transfer functions: Experimental and numerical investigations.

Numerical simulations of head-related transfer functions (HRTFs) conventionally assume a rigid boundary condition for the pinna. The human pinna, however, is an elastic deformable body that can vibrate due to incident acoustic waves. This work investigates how sound-induced vibrations of the pinna can affect simulated HRTF magnitudes. The work will motivate the research question by measuring the sound-induced vibrational patterns of an artificial pinna with a high-speed holographic interferometric system. Then, finite element simulations are used to determine HRTFs for a tabletop model of the B&K 5128 head and torso simulator for a number of directions. Two scenarios are explored: one where the pinna is modeled as perfectly rigid, and another where the pinna is modeled as linear elastic with material properties close to that of auricular cartilage. The findings suggest that pinna vibrations have negligible effects on HRTF magnitudes up to 5 kHz. The same conclusion, albeit with less certainty, is drawn for higher frequencies. Finally, the importance of the elastic domain's material properties is emphasized and possible implications for validation studies on dummy heads 1as well as the limitations of the present work are discussed in detail.

Research on the centre-of-mass adjustment method for the head of an anthropometric test device based on a head impact biomechanics model

Head injury is the primary cause of serious lesions or death in automobile accidents. During crash tests, the mass and centre-of-mass position of the head of anthropometric test devices are crucial factors determining the accuracy of head injury test data. However, owing to the irregular shape as well as complex structure and material composition of the head of dummies, problems such as uneven mass distribution easily occur, resulting in deviations between the actual and designed positions of the centre-of-mass of the head. This study conducted research on head impact biomechanics and the centre-of-mass adjustment method for the head of dummies. Specifically, the biomimetic mechanical equivalent of the head was investigated, and head impact mechanics were analysed. Then, a predictive model was established for head drop mechanical response; the accuracy of this model was verified through head drop experiments. Based on the model, the law of centre-of-mass influence on the mechanical response of the dummy head was investigated, yielding an evaluation method for the different mechanical responses of the head. Using the rotational centre-of-mass measurement method, the mass and centre-of-mass position of the head were obtained. The distributed centre-of-mass adjustment method based on the principle of torque equilibrium was utilized to solve the deviations in the centre-of-mass position, the geometric dimensions of the counterweights and the centre-of-mass itself. Two counterweights were distributed on both sides of the internal cavity wall of the dummy head, resolving the positioning issue of the counterweights in the head cavity. The rationality of the centre-of-mass adjustment results was analysed using the predictive model for head impact mechanical response. The analysis results indicate that the centre-of-mass-adjusted dummy head better aligned with the mechanical response of the head in real collision scenarios, providing a new approach for the adjustment of the centre-of-mass of the head of dummies.

Effect of Curvature Shape of Transparent COVID-19 Protective Face Shields on the Speech Signal

Recent papers and studies over the course of last three years have shown that COVID-19 has a negative impact on the speech communication quality between people. This paper presents an influence analysis of the curvature shape of protective transparent shields on the speech signal. Five shields made of the same material and dimensions but with different curvatures were analyzed, from a completely flat to a very curved shield which has the same shape of curvature at its top and bottom and covers the entire face. The influence of the shield is analyzed with two types of experiments – one using dummy head with integrated artificial voice device, and the other using real speakers (female and male actors). It has been shown that usage of protective shields results in a relative increase in the speech signal level, in the frequency range of around 1000 Hz, compared to the situation when protective shields are not used. The relative increase in speech signal levels for large-curvature shields can be up to 8 dB. The possible causes of this phenomenon have been analyzed and examined.

Uncertainty Constraint on Headphone Secondary Path Function for Designing Cascade Biquad Feedback Controller with Improved Noise Reduction Performance

The uncertainty in the secondary path of active noise control (ANC) headphones affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of a dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized using the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensure more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

AI-based denoising of head impact kinematics measurements with convolutional neural network for traumatic brain injury prediction.

Wearable devices are developed to measure head impact kinematics but are intrinsically noisy because of the imperfect interface with human bodies. This study aimed to improve the head impact kinematics measurements obtained from instrumented mouthguards using deep learning to enhance traumatic brain injury (TBI) risk monitoring. We developed one-dimensional convolutional neural network (1D-CNN) models to denoise mouthguard kinematics measurements for tri-axial linear acceleration and tri-axial angular velocity from 163 laboratory dummy head impacts. The performance of the denoising models was evaluated on three levels: kinematics, brain injury criteria, and tissue-level strain and strain rate. Additionally, we performed a blind test on an on-field dataset of 118 college football impacts and a test on 413 post-mortem human subject (PMHS) impacts. On the dummy head impacts, the denoised kinematics showed better correlation with reference kinematics, with relative reductions of 36% for pointwise root mean squared error and 56% for peak absolute error. Absolute errors in six brain injury criteria were reduced by a mean of 82%. For maximum principal strain and maximum principal strain rate, the mean error reduction was 35% and 69%, respectively. On the PMHS impacts, similar denoising effects were observed and the peak kinematics after denoising were more accurate (relative error reduction for 10% noisiest impacts was 75.6%). The 1D-CNN denoising models effectively reduced errors in mouthguard-derived kinematics measurements on dummy and PMHS impacts. This study provides a novel approach for denoising head kinematics measurements in dummy and PMHS impacts, which can be further validated on more real-human kinematics data before real-world applications.

Evaluation of the Respective Effects of Microphone Type and Dummy Head Type on Measured Head-Related Transfer Functions

A dummy head is a tool used to generate binaural recordings, i.e. recordings when listened to through headphones that allow for the listener to hear from the dummy's perspective. A dummy head typically includes pinnae and ear canals in which microphones are placed. The global shape of a dummy head replicates an average-sized human head, and variations around this average will depend on the manufacturer (pinnae of different size, presence of a nose or a mouth). This paper describes measurements conducted on two dummy heads in order to evaluate and rank the respective influence of microphone type and dummy head shape on spatialization cues. Four possible cross configurations are tested, that is head 1 or 2 with microphones pair 1 or 2. For each configuration, head-related transfer functions are measured in an anechoic room for various azimuth and elevation angles. The results obtained show that the effect of the dummy head shape is larger than the effect of the microphone type on measured head-related transfer functions. A practical implication of this result is found when microphones have to be replaced on a given dummy head.

Consideration on the uncertainty of audiometer calibration and pure tone audiometry

Pure Tone Audiometry (PTA) is the fundamental method for determining a subject's hearing threshold. The process is described in detail in ISO 8253-1, which also includes information about the measurement uncertainty of PTA in Annex A. Because the major value is based on the allowable tolerance of each equipment and the assumed value with sufficient margin. In this study, the factors contribute to the uncertainty of audiometer calibration and PTA are investigated in the quantitative manner. There are two main groups of uncertainty components: the audiometer and the subject. Components related to the audiometer include uncertainties in the stimuli of audiometer and it can be evaluated by the calibration of audiometer. The calibration process is thoroughly examined and the uncertainties in airborne audiometry are evaluated. The effect of components related to the subject include the effects of head size on tension, ear shape on cavity volume, and headphone placement are observed by using an ear simulator and a dummy head.

Near-field modeling of the head-related transfer function by using the dummy head sound source

Various approaches based on direct measurement have been used to obtain the precise headrelated transfer function (HRTF). However, several problems persist, such as scattering of sound source and distance effect, which are related to the measurement configuration. In this work, the modified dummy head having two sound sources located at the ear positions is applied as the sound source reciprocally to overcome the trouble. By using the near-field acoustic holography, the sound sources located in the ear holes are reconstructed from the measured data in the near-field hologram. One can predict the acoustic transfer function between the ear holes and the field positions at any point using the recovered source information described in spherical harmonics. The obtained transfer function is valid for predicting the binaural response from any sound source position. This configuration is possible to measure the near-field response with the relatively small scattering effect because of the low Helmholtz number of microphones. The far-field reconstruction of HRTF is also possible with the near-field measurement data using acoustical holography. The proposed method is demonstrated with the modified B&amp;K HATS system, in which the microphones in the ear holes are replaced by pipe sources connected to the loudspeaker.

Art Is Magic

Art Is Magic

Experimental evaluation of bilateral Ambisonics-based binaural room transfer function synthesis with application to personal sound zones

This study experimentally evaluates the bilateral Ambisonics method for synthesizing binaural room transfer functions (BRTFs) and explores its application in generating personal sound zones (PSZs) around listeners’ ears. Bilateral Ambisonics is proposed for improving the spatial sound reproduction accuracy at a limited Ambisonics order, by shifting the origin of Ambisonics representation from the head center to the two ears. While numerical simulations have demonstrated its superiority over traditional Ambisonics, little attention has been given to validating its usability for reproduction in realistic environments with loudspeakers. Experiments are conducted wherein the BRTFs of a dummy head listener are first synthesized by combining the spatial room transfer functions (SRTFs) measured with a spherical Ambisonics microphone array at the ear position and the corresponding head-related transfer functions (HRTFs), and then compared with the actual in situ measured ones. Furthermore, the quality of the synthesized BRTFs is examined in the context of an in-house PSZ system, by objectively evaluating the performance of PSZ filters designed with such BRTFs in terms of acoustic isolation metrics. The application of synthesized BRTFs to PSZ systems circumvents the need for in-situ BRTF measurements, making it highly feasible to deploy such systems while achieving high acoustic isolation.

High quality low complexity binaural rendering for headphones

Playing back immersive audio via headphones has been a research topic for a long time. Although there have been advances, bigger breakthroughs are still missing. The basic idea of binaural rendering systems can be summarized with the following elements: The emission characteristics of the audio source, the transmission path from audio source to listener as well as suitable head related transfer functions. Systems following this basic paradigm range from dummy head stereophony over purely simulation based approaches to current parametric algorithms including the usage of room impulse responses. According to research in audio cognition, it is important to incorporate positional and rotational tracking data of the head close to real time as well as acoustic information about the listening room. Based on the chosen approach, the effort to acquire the measurements, to prepare the rendering or the computational demand of the rendering itself might be high. In this paper, we report on a low complexity rendering system which allows high quality binaural reproduction. A recent listening test and many reviews from listeners have proven, that the perception of the rendered audio signals is equivalent to listening to real audio sources in a room.

Massive Solubility Changes in Neuronal Proteins upon Simulated Traumatic Brain Injury Reveal the Role of Shockwaves in Irreversible Damage.

We investigated the immediate molecular consequences of traumatic brain injuries (TBIs) using a novel proteomics approach. We simulated TBIs using an innovative laboratory apparatus that employed a 5.1 kg dummy head that held neuronal cells and generated a ≤4000 g-force acceleration upon impact. A Proteome Integral Solubility Alteration (PISA) assay was then employed to monitor protein solubility changes in a system-wide manner. Dynamic impacts led to both a reduction in neuron viability and massive solubility changes in the proteome. The affected proteins mapped not only to the expected pathways, such as those of cell adhesion, collagen, and laminin structures, as well as the response to stress, but also to other dense protein networks, such as immune response, complement, and coagulation cascades. The cellular effects were found to be mainly due to the shockwave rather than the g-force acceleration. Soft materials could reduce the impact's severity only until they were fully compressed. This study shows a way of developing a proteome-based meter for measuring irreversible shockwave-induced cell damage and provides a resource for identifying protein biomarkers of TBIs and potential drug targets for the development of products aimed at primary prevention and intervention.

The Benefit of Binaural Hearing Among Listeners with Sensorineural Hearing Loss

The performance of binaural processing may be disturbed in the presence of hearing loss, especially of sensorineural type. To assess the impact of hearing loss on speech perception in noise regarding binaural processing, series of speech recognition measurements in controlled laboratory conditions were carried out. The spatial conditions were simulated using dummy head recordings played back on headphones. The Intelligibility Level Difference (ILD) was determined by measuring the change in the speech reception thresholds (SRT) between two configurations of a masking signal source (N) and a speech source (S), namely the S0N90 condition (where numbers stand for angles in horizontal plane) and the co-located condition (S0N0). To disentangle the head shadow effect (better ear effect) from binaural processing in the brain, the difference between binaural and monaural S0N90 condition (so-called Binaural Intelligibility Level Difference, BILD) value was calculated. Measurements were performed with a control group of normal-hearing listeners and a group of sensorineural hearing-impaired subjects. In all conditions performance of the hearing-impaired listeners was significantly lower than normal-hearing ones, resulting in higher SRT values (3 dB difference in the S0N0 configuration, 7.6 dB in S0N90 and 5 dB in monaural S0N90). The SRT improvement due to the spatial separation of target and masking signal (ILD) was also higher in the control group (8.1 dB) than in hearing-impaired listeners (3.5 dB). Moreover, a significant deterioration of the binaural processing described by BILD was found in people with sensorineural deficits. This parameter for normal-hearing listeners reached a value of 3 to 6 dB (4.6 dB on average) and decreased more than two times in the hearing-impaired group to 1.9 dB on average (with a deviation of 1.4 dB). These findings could not be explained by individual average hearing threshold (standard in audiological diagnostics) only. The outcomes indicate that there is a contribution of suprathershold deficits and it may be useful to consider binaural SRT measurements in noise in addition to the pure tone audiometry resulting in better diagnostics and hearing aid fitting.