Dry System Research Articles

Influence of Electrohydrodynamics on the Drying Characteristics and Volatile Components of Ginger

This article studies the electrohydrodynamic drying of ginger. In this work, drying experiments were performed in an electrohydrodynamic drying (EHD) system at various AC voltages (0 kV (control), 15 kV, 20 kV, 25 kV, and 30 kV). The drying properties and volatile components of ginger were thoroughly examined and studied using IR spectroscopy and GC–MS. The findings revealed that electrohydrodynamics significantly increased the drying rate and reduced the drying time of ginger, with a sevenfold increase in drying rate and a one-third reduction in drying time at 30 kV. The peak of the infrared spectrum of ginger remains unchanged. We found 240 volatile chemicals under different drying voltages. The primary volatile chemicals were esters and aldehydes. The ginger products dried at 30 kV had the lowest aldehyde concentration. These findings give an experimental and theoretical foundation for applying electrohydrodynamics to the subject of ginger drying.

Finding Critical Factors for Developing Dynamic Models to Optimize Greenhouse Solar Dryer’s Environmental Conditions

This paper is focused on the formulation of a mathematical model for greenhouse solar dryer systems in the context of determining the principal drivers of efficiency of the solar dryer. The model was built by evaluating the correlation coefficients of each term and only those terms which had high levels of significance were retained. To test this model, experiments were replicated with measurements being taken in the different sections of the greenhouse to provide a large spectrum of the environmental conditions involved. The values of the technical coefficients are predicated on internal air temperature, humidity ratio and weight of the product with fixed scales, avoiding sophisticated complex models prone to overfitting. By using terms with high correlation, the model is less likely to be affected by outliers and total correlation or cross correlation is low, thereby making the model practical. The outcomes of this research, therefore, offer a scientifically viable and a practical approach to enhancing drying processes in greenhouse solar dryer systems.

Compaction Evolution and Mechanisms of Granular Materials Due to Gyratory Shearing

Granular systems, no matter whether they are dry or saturated, are commonly encountered in both natural scenarios and engineering applications. In this work, we tackle the compaction problem of both dry and saturated granular systems under gyratory shearing compaction, where particles are subjected to constant pressure and continuous shear rate, which is quite different from the traditional cyclic shearing compaction. Such phenomena are crucial to the compaction of asphalt mixtures or soils in civil engineering and can be extended to other areas, such as powder processing and pharmaceutical engineering. In this study, we investigated the behavior of both dry and fully saturated mono-dispersed granular materials under gyratory shearing compaction using the discrete element method (DEM) and found that the gyratory speed or interstitial fluid viscosity has almost no impact on the compaction behavior, while the pressure and the particle size play more important roles. Additionally, it is the inertial time scale which dictates the compaction behavior under gyratory shearing in most cases; meanwhile, the viscous time scale can also have influence in some conditions. This work determines the similarity and unity between the granular gyratory compaction and the rheology of granular systems, which has direct relevance to various natural and engineering systems.

Economic Sustainability Foraging Scenarios for Ruminant Meat Production—A Climate Change Adapting Alternative

Climate changes affect all agricultural production systems, directly or indirectly, including that of ruminant meat, through the limitation of forage resources sensitive to reduced water regimes and drought. The present paper assessed the economic sustainability of ruminant meat production in the context of climate change, with a particular focus on integrating bioeconomy principles through the use of drought-resistant crops such as sorghum and millet in livestock feed. This study included scenarios for two farm-level models, a sheep fattening farm and a cattle fattening farm, to determine the economic benefit and impact of integrating resilient crops in the total feed ration. The findings showed that the dry scenario system could offer economic and environmental advantages over traditional water-intensive crops like maize. The results demonstrated that replacing maize with sorghum or millet could result in a reduction in feed costs and enhanced economic benefit over the traditional feed system.

Design and assessment of an adapted absorber solar air collector tailored for sustainable drying applications

The design of a relevant solar air collector (SAC) is imperative to make the drying industries self-reliant and sustainable in terms of energy. However, the literature doesn’t describe the coherent design assessment of SAC, and its viability for a drying system provided the scale-up opportunity for commercial applications. Hence, the present work was devoted to estimating the heat load for a particular drying condition, a methodological understanding of SAC design, and an investigation of the performance of the newly developed solar collector. The essential design criteria were the moisture content of fresh and intended dried items, physical attributes of items, dryer capacity, preferred drying temperature, projected drying duration, required air speed (based on dryer type), and local climate (solar radiation, ambient temperature and relative humidity). The regular semi-hexagonal shape aluminium (Al) sheet was chosen to introduce air turbulence while maximizing the surface area available for heat transfer. The regular semi-hexagonal absorber was outfitted with helical springs to generate air turbulence and augment heat transfer. A double glazing (polycarbonate) of 5 mm apart was mounted to impede radiation heat loss. Three successive days of the experimental study showed that the average temperature increases of air passing through SAC were 36.02 °C, 37 °C, and 39.2 °C. The optimal tilt angle with the horizontal surface was found to be 35° in a south-facing direction for the month of January. The highest energy efficiency was found to be 40.5 %, while the lowest was found to be 24.73 %. The sustainability index of the SAC was found to be 1.02. The experimental results clearly demonstrate that the designed SAC was capable of supplying adequate heat energy (at the minimum of 155.86 W/hr.) to meet the necessary heat load (125.82 W/hr.) for agro-products drying at the designed capacity.

Exergy Efficiency and Energy Efficiency of Double Air Pass Solar Tunnel Air Dryer: A CFD Analysis

This work presents, the computational fluid dynamics simulation of a forced convection double air pass solar tunnel drying system to study the temperature distribution, the flow behaviour of the air stream, and the exergy performance. Realizable k-epsilon non-equilibrium wall function turbulence model, discrete ordinate radiation model, and species transport were used. The average temperature, thermal efficiency, and exergy efficiency were found to 59.2 oC, 30%, and 9.41%, respectively. The result revealed that the uniform temperature and velocity distribution throughout the heating and drying chamber. Therefore, the newly developed double air pass solar tunnel dryer enhances the air temperature and the exergy performance leads to the increment of drying rate and reduction of drying period.

Ciphering of greenhouse gases from constructed wetlands in Lucknow (U. P. India)

This study evaluates how greenhouse gases (GHGs) contribute to global warming, drawing attention to the substantial effect of human activity on GHG concentrations in the atmosphere. The lower atmosphere warms as a consequence of the absorption as well as the emission of thermal infrared radiation by greenhouse gases, which are both naturally occurring and created by human beings. Since the 1950s, it has been determined that carbon dioxide (CO2) contributes a vital part in tweaking the environmental conditions, with other gases which include methane (CH4), nitrous oxide (N2O), and CFCs also playing a significant role. India is the third-biggest producer of greenhouse gases (GHGs) due to its enormous population and fast economic growth. This study looks into the GHG emissions from manmade wetlands (CWs) and seasonal assessments conducted in Lucknow and the neighboring wetlands. The emissions of nitrous oxide and methane from CWs are computed using particular formulas and parameters. Utilizing particular formulas and parameters, the emissions of methane and nitrous oxide from CWs are computed. The results emphasize the significance of efficient management techniques such as hydrological control, organic matter control, intermittent drying, shading, adding biochar, and hybrid systems in reducing greenhouse gas emissions from wetlands. The mitigation of the ecological consequences of chemical warfare and the fight against global warming necessitates these protocols.

Design and Development of a Portable Solar Panel Cleaner with Dry and Wet Cleaning Systems

Solar panels (PV modules) are a popular alternative energy source. The outer layer of toughened glass protects the solar cells from heat and weathering. The cleanliness of the surface has a significant impact on energy conversion, as dirt and dust can hinder the absorption of solar radiation. This study aimed to design, develop and analyse a solar panel cleaner using innovative wet and dry cleaning technologies. The design process resulted in detailed equipment specifications. Key components were assembled and tested for functionality. The dry cleaning system uses a rotating brush (three-cycle mops) connected to a DC motor. The wet cleaning system uses a nozzle at the end of the tool to deliver pressurised water from a DC pump connected to a water tank. The prototype was field-tested to assess the effectiveness of wet and dry cleaning methods on solar panels. The solar panel cleaner can be used for both wet and dry cleaning. Future improvements may result in an aesthetically pleasing, durable, effective and efficient solar panel cleaner.

Smart integration in agriculture: an Arduino-driven rice grain dryer for optimal post-harvest management

In the field of agriculture, the post-harvest stage often presents a multitude of obstacles that have the potential to undermine the quality and longevity of the crop. One of the primary obstacles in rice production is the effective drying of rice grains, which is crucial for preventing problems such as mold growth, discoloration, and unintentional germination. To tackle this issue, we propose an innovative solution: a rice grain drying system driven by an Arduino microcontroller. This device effectively combines technology accuracy with agricultural needs. The system is equipped with a very precise temperature sensor to maintain a uniform drying environment, fluctuating within the range of 50–60 °C. The use of a nichrome heater, selected for its consistent and dependable heat production, is complemented by an air blower to ensure the even distribution of heat throughout the drying chamber. One notable characteristic of this innovation is its significant drying capacity of 50 kg in each operation. The effectiveness of the product was verified by a rigorous testing process. A batch of glutinous rice weighing 25 kg, initially containing 25.5% moisture, was successfully reduced to 13.5% moisture content within a time frame of 125 min. In a similar vein, a batch of grains weighing 40 kg, which had just undergone threshing, had a moisture content of 22% initially. Remarkably, this batch achieved the desirable moisture level of 14% within a mere two-hour timeframe. This innovative technology not only provides a resolution to the difficulties faced in post-harvest processes but also signifies a fundamental change in thinking, introducing a fresh era where intelligent technology seamlessly integrates with traditional agricultural methods.

Rice Under Dry Cultivation-Maize Intercropping Improves Soil Environment and Increases Total Yield by Regulating Belowground Root Growth.

Under the one-season-a-year cropping pattern in Northeast China, continuous cropping is one of the main factors contributing to the degradation of black soil. Previous studies (on maize-soybean, maize-peanut, and maize-wheat intercropping) have shown that intercropping can alleviate this problem. However, it is not known whether intercropping is feasible for maize and rice under dry cultivation, and its effects on yield and soil fertility are unknown. A three-year field-orientation experiment was conducted at Jilin Agricultural University in Changchun city, Jilin Province, China, consisting of three cropping regimes, namely rice under dry cultivation-maize intercropping (IRM), sole rice under dry cultivation (SR), and sole maize (SM). All straw was fully returned to the field after mechanical harvesting. Rice under dry cultivation-maize intercropping with a land-equivalent ratio of 1.05 (the average of three years values) increased the total yield by 8.63% compared to the monoculture system. The aggressivity (A), relative crowding coefficient (K), time-area-equivalent ratio (ATER), and competition ratio (CR) value were positive or ≥1, also indicating that the rice under dry cultivation-maize intercropping had a yield advantage of the overall intercropping system. This is because the intercropped maize root length density (RLD) increased by 33.94-102.84% in the 0-40 cm soil layer, which contributed to an increase in the soil porosity (SP) of 5.58-10.10% in the 0-30 cm soil layer, an increase in the mean weight diameter of soil aggregates (MWD) of 3.00-15.69%, an increase in the geometric mean diameter of soil aggregates (GMD) of 8.16-26.42%, a decrease in the soil bulk density (SBD) of 4.02-7.35%, and an increase in the soil organic matter content (SOM) of 0.60-4.35%. This increased the water permeability and aeration of the soil and facilitated the absorption of nutrients and water by the root system and their transportation above ground, and the plant nitrogen, phosphorus, and potassium accumulation in the intercropping system were significantly higher than that in monoculture treatment, further promoting the total yield of intercropping. This suggests that rice under a dry cultivation-maize intercropping system is feasible in Northeast China, mainly because it promotes belowground root growth, improves the soil environment, and increases the total yield of intercropping.

Ant‐Pollination: Conditional Outcomes Depending on Environmental Features and Species Interactions

ABSTRACTThe intricate web of interactions in nature has led to unexpected partnerships between plants and animals, greatly influencing ecosystem dynamics. In this discussion, we'll explore the Pollination Syndrome Hypothesis and consider a scenario where a partnership with unexpected pollinators emerges. We suggest that ant pollination has been largely overlooked, but ants can surprisingly play a crucial role and have a history of success in pollinating dry system plants. We will present both negative and positive aspects that must be observed in ant‐pollination syndrome. Additionally, we aim to explore the often‐underestimated phenomenon of ant pollination and the overlooked tiny, discreet, unnoticed flowers found in our fields and forests, especially in dry ecosystems, savannas and mountain fields, which may hold numerous undiscovered secrets about these interactions. We encourage young biologists to engage in natural history observations and to perform manipulative experiments directly in the field to understand the true nature of these successful ant‐pollinations.

Case-control study on associations of hemorrhagic bowel syndrome in swine with feed characteristics and intestinal pathogens

Haemorrhagic bowel syndrome (HBS) is one of the most common causes of death in fattening pigs worldwide. The objective of this descriptive study was to systematically assess predictors or causal components for the appearance of HBS using case farms (mortality rate caused by HBS ≥ 1.5%) in comparison with control farms (mortality rate caused by HBS ≤ 0.25%), focusing on feed ingredients, feed quality and size, and gastrointestinal pathogens. The inclusion of sugar beet as a feed component in liquid feeding systems was found to be associated (p = 0.03) with farms identified as HBS cases. Another predictive or causal factor found for liquid feeding systems, but only for those using meal, was particle size. A higher percentage of small particles (< 2 mm) in the meal was associated with a higher risk of being an HBS case farm (p = 0.02), while no relevant association was detected for the use of pellets. Sugar beet in the diet was also associated with the incidence of HBS.The microbial quality of the feed in dry feeding systems, specifically the number of total aerobes at the first and last outlet tubes, was associated with a higher incidence of HBS (p = 0.03). Faecal sample analysis showed a difference (p < 0.05) in the prevalence of B. pilosicoli in the herd category (case vs. control herd). In this descriptive study, five predictive or causal factors were identified for an HBS farm with a mortality rate due to HBS ≥ 1.5%. These included the number of aerobes in dry matter samples from the first and last feeders, the particle diameter of the meal used in liquid feeding systems and sugar beet as a component of liquid feeding rations, and the presence of B. pilosicoli as an infectious agent at animal level. Relevant associations reinforce the findings of the previously published Swiss study that HBS is a multifactorial syndrome involving different aspects of pig production and cannot be attributed to a single cause. Further studies are needed to develop evidenced based causal models for HBS in swine.

Performance of Small-Scale Hermetic Storage Systems Under Periodic Access

This study characterizes the grain management performance of a novel integrated grain drying and storage system (iGDSS) adapted from 208 L drums to combat postharvest loss in developing countries through providing in situ mechanized drying and hermetic storage. The six-month storage trials of 14% moisture content maize compared different access mechanisms and two levels of pest pressure: 0 and 10 maize weevils/kg grain. This experiment allowed comparisons of differential oxygen consumption rates in small-scale hermetic systems with and without storage pests, which has not been widely reported in the literature. The iGDSS system was found to maintain grain quality parameters in dry grains with and without storage pests. After six months of storage, the results demonstrated no statistically significant difference in the moisture content, test weight, germination, proportion of broken and damaged kernels, and presence of colony-forming units between inoculated and non-inoculated systems. The iGDSS was also found to maintain oxygen intrusion rates of 0.10–0.13% O2/day, below recommended thresholds of 0.15% required to maintain benefits of modified atmosphere storage. These results indicate that the iGDSS can provide safe and reliable grain storage to smallholder farmers in developing countries, and that the drying functions of iGDSS can promote outcomes in hermetic storage.

Optimization of Organic Rankine Cycle for Hot Dry Rock Power System: A Stackelberg Game Approach

Due to its simple structure and stable operation, the Organic Rankine Cycle (ORC) has gained significant attention as a primary solution for low-grade thermal power generation. However, the economic challenges associated with development difficulties in hot dry rock (HDR) geothermal power systems have necessitated a better balance between performance and cost effectiveness within ORC systems. This paper establishes a game pattern of the Organic Rankine Cycle with performance as the master layer and economy as the slave layer, based on the Stackelberg game theory. The optimal working fluid for the ORC is identified as R600. At the R600 mass flow rate of 50 kg/s, the net system cycle work is 4186 kW, the generation efficiency is 14.52%, and the levelized cost of energy is 0.0176 USD/kWh. The research establishes an optimization method for the Organic Rankine Cycle based on the Stackelberg game framework, where the network of the system is the primary optimization objective, and the heat transfer areas of the evaporator and condenser serve as the secondary optimization objective. An iterative solving method is utilized to achieve equilibrium between the performance and economy of the ORC system. The proposed method is validated through a case study utilizing hot dry rock data from Qinghai Gonghe, allowing for a thorough analysis of the working fluid and system parameters. The findings indicate that the proposed approach effectively balances ORC performance with economic considerations, thereby enhancing the overall revenue of the HDR power system.

Assessment of a LPG hybrid solar dryer assisted with smart air circulation system for drying basil leaves

The fluctuation of solar radiation throughout the day presents a significant obstacle to the widespread adoption of solar dryers for the dehydration of agricultural products, particularly those that are sensitive to high temperatures, such as basil leaf drying during the winter season. Consequently, this recent study sought to address the limitations of solar-powered dryers by implementing a hybrid drying system that harnesses both solar energy and liquid petroleum gas (LPG). Furthermore, an innovative automatic electronic unit was integrated to facilitate the circulation of air between the drying chamber and the ambient environment. Considering the solar radiation status in Egypt, an LPG hybrid solar dryer has been developed to be suitable for both sunny and cloudy weather conditions. This hybrid solar dryer (HSD) uses indirect forced convection and a controlled auxiliary heating system (LPG) to regulate both temperature and relative humidity, resulting in increased drying rates, reduced energy consumption, and the production of high-quality dried products. The HSD was tested and evaluated for drying basil leaves at three different temperatures of50, 55, and 60 °C and three air changing rates of 70, 80, and 90%, during both summer and winter sessions. The obtained results showed that drying basil at a temperature of 60 °C and an air changing rate of 90% led to a decrease in the drying time by about 35.71% and 35.56% in summer and winter, respectively, where summer drying took 135–210 min and winter drying took 145–225 min to reach equilibrium moisture content (MC). Additionally, the effective moisture diffusivity ranged from 5.25 to 9.06 × 10− 9 m2/s, where higher values of effective moisture diffusivity (EMD) were increased with increasing both drying temperatures and air change rates. Furthermore, the activation energy decreased from 16.557 to 25.182 kJ/mol to 1.945–15.366 kJ/mol for the winter and summer sessions, respectively. On the other hand, the analysis of thin-layer kinetic showed that the Modified Midilli II model has a higher coefficient of determination R2, the lowest χ2, and the lowest root mean square error (RMSE) compared to the other models of both winter and summer sessions. Finally, the LPG hybrid solar dryer can be used for drying a wide range of agricultural products, and it is more efficient for drying medicinal plants. This innovative dryer utilizes a combination of LPG and solar energy, making it efficient and environmentally friendly.

A Static/Dynamic Coupled Harmonic Balance Method for Dry Friction Systems Containing Rigid Body Modes

Abstract A harmonic balance method for under-constrained dry friction systems containing rigid body modes (HBM-RBM) is proposed. This method aims to overcome the encountered obstacle when applying the harmonic balance method to turbine blades damped by underplatform dampers. The inspiration for HBM-RBM comes from the free interface modal synthesis method. The key innovation involves deriving the elastic inversion of the singular stiffness matrix through the elimination of rigid body modes. In this way, the general HBM framework can be adopted, and the frequency response of under-constrained dry friction systems can be solved in a static/dynamic coupled manner. The accuracy and efficiency are both verified on a lumped parameter model and a finite element model of turbines with UPDs from a real gas turbine. A comparative study between the HBM-RBM and the commonly adopted way of imposing artificial grounding springs (HBM-AGS) is conducted. Results demonstrate that the HBM-RBM holds a significant advantage over HBM-AGS, as it eliminates the need for artificial grounding springs (AGS) and avoids the necessity for numerous trial cases to determine AGS stiffness.

Fixing collapsed dry anaerobic digestion system of kitchen waste caused by severe VFAs accumulation

Severe inhibition by volatile fatty acids (VFAs) frequently occurs during the dry anaerobic digestion of kitchen waste at high organic load rate (OLR), leading to decreased biogas production and even the collapse of the anaerobic digestion system. In this study, VFAs accumulation was significantly reduced by adding powder-activated carbon (PAC) or alkaline additives (AA), thus restoring the collapsed system to a stable operating state. With the addition of PAC or AA, the maximal OLR reached 11.14 g VS/(L·d), which was 30 % higher than observed without any additives (control group), while the VFAs concentration was maintained below 3000 mg/L. At this OLR, the volumetric biogas production rate stabilized at 5.1 L/(L·d) in the presence of PAC and AA, while that of the control group gradually decreased to zero. The VFAs concentration with PAC addition was 86 % lower than that of the control group, possibly because PAC might stimulate the formation of direct interspecies electron transfer between syntrophic bacteria and methanogens (Methanosarcina), thereby promoting VFAs degradation. The addition of AA, which resulted in a 95 % decrease in ammonia-nitrogen concentration, can provide a good growth environment for the microorganisms involved in acidogenesis and hydrogenotrophic methanogenesis.

Increase the economic potential of the Ambulu Community by providing appropriate batik drying technology

One of the MSMEs developed Batik as a regional product is Rezti's Batik. Rezti's Batik is located in Ambulu, Jember Regency, about 28.4 km from the University of Jember. Increasing the number of consumer orders has made Rezti's Batik production continue to increase. One of the obstacles faced by Rezti's Batik is the process of making Batik which takes a long time because the drying process still relies on heat from the sun, which takes 4-6 hours. The process can also take longer if the rainy season slows the production process's completion. The solution method is the manufacture of appropriate technology in the form of installing a batik cloth dryer. The batik cloth drying installation implementation at Rezti's Batik is a drying system that utilizes heat from the furnace in the sagging process as a heating medium. The designed dryer consists of a stove as a heat generator which will later be distributed with air from the blower so that the hot air will spread evenly throughout the room.

Study of flammable gases generation and radionuclide release during and after drying of damaged VVER SNF

The paper presents an experimental evaluation of drying the damaged VVER SNF after the wet storage. The aim of the experiments was to justify the fire safety of air-tight canisters with the dried SNF during transportation, storage, and reprocessing. Keeping the SNF in boric acid during the experiments determined the concentration of uranium, plutonium, and specific activity of fission products in the solution inside the model canisters with the SNF. The canisters with the SNF underwent the thermal vacuum drying to determine the process parameters (temperature, residual pressure, drying rate), a hydrogen release, 85Kr activity during the drying, and an airborne radionuclide release onto the filters of the SNF thermal vacuum drying system. The results of weighing the baskets of the canisters before soaking in the boric acid and after drying at 160 °С to the residual pressure below 6 mbar showed that the difference in weight is almost the same as the calculated difference in weight of H3BO3 loaded into the canister and the weight after the complete decomposition into B2O3. Thus, we have discovered that the boric acid undergoes complete decomposition into boric anhydride, and the SNF corrosion products generate hydrogen that accumulates in the air-tight canister. We also considered the hydrogen that accumulated in the air-tight model canister with the dried SNF as a result of the radiolysis of hydrated corrosion products of the spent oxide nuclear fuel, as well as a release of gaseous fission products (GFP) inside the canister. We calculated the quantity of the hydrated corrosion products of uranium oxide after the wet storage and determined their chemical composition after the thermal-vacuum drying. The equation with an exponential decay function describes the hydrogen accumulation. The calculated maximum volume of hydrogen and uranium in the SNF corrosion products suggests that the SNF corrosion product is schoepite with the number of gyrated water molecules corresponding to the formulas from UO3·0.95H2O to UO3·1.5H2O. The received data allows for the fire safety justification of drying the wet damaged SNF and handling the dried SNF during transportation and storage.

Performance analysis of heat pump drying system combined with rotor dehumidification for low temperature drying of mango slices

In order to solve the problems of low drying efficiency and poor drying quality existing in the current closed heat pump drying system (CHPD), a closed carbon dioxide heat pump drying system (CHPRD) with the function of combining rotor dehumidification was designed. This study investigates the drying kinetics and quality characteristics of CHPRD in low-temperature drying processes using mango as the drying material through experimental studies and theoretical analysis. The experimental results showed that the drying rate of CHPRD increased by 29% and 17.8%, the moisture removal rate per unit energy (SMER) by 14.2% and 12.5%, and the coefficient of performance (COP) by 17.3% and 12.0%, respectively, compared with that of CHPD in the low-temperature drying process with loading amounts of 400 and 450 g, respectively. In terms of drying quality, the rehydration factor (Rf ) of CHPRD-dried mango slices increased by 6.0% and 5.0%, the ascorbic acid content increased by 15.0% and 14.4%, and the color difference (ΔE) was lower by 11.0% and 5.6%, respectively. These improvements indicate that CHPRD provides better drying kinetics and higher quality of dried material. Based on the experimental data, simulation fitting was conducted, revealing that the two-term model is the best mathematical model to simulate the drying characteristics of CHPRD for mango.