Design Of Drug-eluting Stents Research Articles

A Randomized Controlled Trial Comparing BioMime Sirolimus-Eluting Stent With Everolimus-Eluting Stent: Two-Year Outcomes of the meriT-V Trial.

Drug-eluting stents (DESs) based on biodegradable polymers (BPs) have been introduced to reduce the risk for late and very late stent thrombosis (ST), which were frequently observed with earlier generations of DES designs based on durable polymers (DPs); however, randomized controlled trials on these DES designs are scarce. The meriT-V trial is a randomized, active-controlled, non-inferiority trial with a prospective, multicenter design that evaluated the 2-year efficacy of a novel third-generation, ultra-thin strut, BP-based BioMime sirolimus-eluting stent (SES) versus the DP-based XIENCE everolimus-eluting stent (EES) for the treatment of de novo lesions. The meriT-V is a randomized trial that enrolled 256 patients at 15 centers across Europe and Brazil. Here, we report the outcomes of the extended follow-up period of 2 years. The randomization of enrolled patients was in a 2:1 ratio; the enrolled patients received either the BioMime SES (n = 170) or the XIENCE EES (n = 86). The three-point major adverse cardiac event (MACE), defined as a composite of cardiac death, myocardial infarction (MI), or ischemia-driven target vessel revascularization (ID-TVR), was considered as the composite safety and efficacy endpoint. Ischemia-driven target lesion revascularization (ID-TLR) was evaluated as well as the frequency of definite/probable ST, based on the first Academic Research Consortium definitions. The trial had a 2-year follow-up completion rate of 98.44% (n = 252/256 patients), and the clinical outcomes assessment showed a nonsignificant difference in the cumulative rate of three-point MACE between both arms (BioMime vs. XIENCE: 7.74% vs. 9.52%, P = 0.62). Even the MI incidences in the BioMime arm were insignificantly lower than those of the XIENCE arm (1.79% vs. 5.95%, P = 0.17). Late ST was observed in 1.19% cases of the XIENCE arm, while there were no such cases in the BioMime arm (P = 0.16). The objective comparisons between the novel BP-based BioMime SES and the well-established DP-based XIENCE EES in this randomized controlled trial show acceptable outcomes of both the devices in the cardiac deaths, MI, ID-TVR, and ST. Moreover, since there were no incidences of cardiac death in the entire study sample over the course of 2 years, we contend that the findings of the study are highly significant for both these DES designs. In this preliminary comparative trial, the device safety of BioMime SES can be affirmed to be acceptable, considering the lower three-point MACE rate and absence of late ST in the BioMime arm over the 2-year period.

Computer Simulation of the Coupling Between Recirculation Flows and Drug Release from a Coronary Drug-Eluting Stent

This study examines the effect of recirculation zones and flow pulsatility on the transfer of the active ingredient from drug-eluting stents to the arterial wall, which can be hindered by recirculation zones located upstream and downstream of stent struts, leading to restenosis and thrombosis. Numerical simulations were conducted using a left coronary artery model with steady or pulsatile flows, and mass transfer analysis was performed on a single-stent strut with a square cross section. The findings offer valuable insights into optimizing the geometric design of drug-eluting stents by controlling the size and dynamics of induced recirculation cells, thereby enhancing the efficacy of stent treatments.

An intricate interplay between stent drug dose and release rate dictates arterial restenosis.

Since the introduction of percutaneous coronary intervention (PCI) for the treatment of obstructive coronary artery disease (CAD), patient outcomes have progressively improved. Drug eluting stents (DES) that employ anti-proliferative drugs to limit excess tissue growth following stent deployment have proved revolutionary. However, restenosis and a need for repeat revascularisation still occurs after DES use. Over the last few years, computational models have emerged that detail restenosis following the deployment of a bare metal stent (BMS), focusing primarily on contributions from mechanics and fluid dynamics. However, none of the existing models adequately account for spatiotemporal delivery of drug and the influence of this on the cellular processes that drive restenosis. In an attempt to fill this void, a novel continuum restenosis model coupled with spatiotemporal drug delivery is presented. Our results indicate that the severity and time-course of restenosis is critically dependent on the drug delivery strategy. Specifically, we uncover an intricate interplay between initial drug loading, drug release rate and restenosis, indicating that it is not sufficient to simply ramp-up the drug dose or prolong the time course of drug release to improve stent efficacy. Our model also shows that the level of stent over-expansion and stent design features, such as inter-strut spacing and strut thickness, influence restenosis development, in agreement with trends observed in experimental and clinical studies. Moreover, other critical aspects of the model which dictate restenosis, including the drug binding site density are investigated, where comparisons are made between approaches which assume this to be either constant or proportional to the number of smooth muscle cells (SMCs). Taken together, our results highlight the necessity of incorporating these aspects of drug delivery in the pursuit of optimal DES design.

Recent Advances in Stent Technology: Do They Reduce Cardiovascular Events?

Drug-eluting stents are used in nearly all cases of percutaneous coronary revascularization and have been shown to be superior to balloon angioplasty or bare metal stents. The designs of these stents are continually evolving to maximize efficacy and safety. This review outlines the important components of a drug-eluting stent and highlights the changes in stent design that have led to the optimization of clinical outcomes. Most stents used in contemporary times are thin strut, durable polymer drug-eluting stents (DES) that elute either everolimus or zotarolimus. Newer DES designs incorporating bioresorbable polymers or ultrathin struts have shown encouraging safety and efficacy profiles. DES are essential for the management of patients with obstructive coronary artery disease and are used in most coronary interventions. Changes in stent designs over the past 30years reflect the ongoing need to address the limitations of earlier stents aimed to improve patient outcomes.

Stent dislodgement force of drug-eluting coronary stents: a bench test.

Coronary stent dislodgement can cause critical complications. The dislodgement force of coronary drug-eluting stents (DES) remains unknown. This study aimed to compare the dislodgement force and pattern of contemporary DES. Five DES designs which commonly used in clinical practice were tested. The force at which the stent dislodges relative to the balloon was measured. For the shim test, peak displacement force, defined as the first peak force that occurs during stent displacement and peak dislodgement force, defined as the peak force required to completely dislodge the stent from the delivery system, were measured. Three examples of each of the stents were tested using the shim test. The peak displacement force of Orsiro (3.1±0.8 N) was lower than that of Xience Sierra (5.8±0.5 N) [Firehawk 3.8±0.2 N, Resolute Onyx 4.5±1.5 N, Synergy 4.8±0.5 N (P=0.024)]. The peak dislodgement force was lowest in Orsiro (3.2±0.8 N) when compared to the other stents (Firehawk 6.6±0.6 N, Resolute Onyx 7.4±0.3 N, Synergy 11.8±0.4 N, Xience Sierra 11.1±1.6 N) (P<0.001); this remained significant in the multiple comparison analysis. During pullback of the stents, most stents buckled without removal. However, the whole Orsiro stent was completely removed from the delivery system. The dislodgement force of DESs differed between stent designs. The Orsiro stent was lower than that of other DES; additionally, it easily removed the whole stent from the delivery system. During the coronary intervention, operators should consider stent design and be cautious when pulling DES back in lesions with calcifications or a previously implanted stent, which are at high risk for stent dislodgement.

MP094 - In vitro assessment of new ureteral biodegradable drug eluting stent design to adjuvant therapy in upper tract urothelial carcinoma

MP094 - In vitro assessment of new ureteral biodegradable drug eluting stent design to adjuvant therapy in upper tract urothelial carcinoma

Bioabsorbable polymer drug-eluting stents with 4-month dual antiplatelet therapy versus durable polymer drug-eluting stents with 12-month dual antiplatelet therapy in patients with left main coronary artery disease: the IDEAL-LM randomised trial.

Improvements in drug-eluting stent design have led to a reduced frequency of repeat revascularisation and new biodegradable polymer coatings may allow a shorter duration of dual antiplatelet therapy (DAPT) after percutaneous coronary intervention (PCI). The Improved Drug-Eluting stent for All-comers Left Main (IDEAL-LM) study aims to investigate long-term clinical outcomes after implantation of a biodegradable polymer platinum-chromium everolimus-eluting stent (BP-PtCr-EES) followed by 4 months DAPT compared to a durable polymer cobalt-chromium everolimus-eluting stent (DP-CoCr-EES) followed by 12 months DAPT in patients undergoing PCI of unprotected left main coronary artery (LMCA) disease. This is a multicentre randomised clinical trial study in patients with an indication for coronary artery revascularisation who have been accepted for PCI for LMCA disease after Heart Team consultation. Patients were randomly assigned in a 1:1 ratio to receive either the BP-PtCr-EES or the DP-CoCr-EES. The primary endpoint was a non-inferiority comparison of the rate of major adverse cardiovascular events (MACE), defined as all-cause death, myocardial infarction, or ischaemia-driven target vessel revascularisation at 2 years. Between December 2014 and October 2016, 818 patients (410 BP-PtCr-EES and 408 DP-CoCr-EES) were enrolled at 29 centres in Europe. At 2 years, the primary endpoint of MACE occurred in 59 patients (14.6%) in the BP-PtCr-EES group and 45 patients (11.4%) in the DP-CoCr-EES group; 1-sided upper 95% confidence interval (CI) 7.18%; p=0.04 for non-inferiority; p=0.17 for superiority. The secondary endpoint event of BARC 3 or 5 bleeding occurred in 11 patients (2.7%) in the BP-PtCr-EES group and 2 patients (0.5%) in the DP-CoCr-EES group (p=0.02). In patients undergoing PCI of LMCA disease, after two years of follow-up, the use of a BP-PtCr-EES with 4 months of DAPT was non-inferior to a DP-CoCr-EES with 12 months of DAPT with respect to the composite endpoint of all-cause death, myocardial infarction or ischaemia-driven target vessel revascularisation.

A viewpoint on material and design considerations for oesophageal stents with extended lifetime

Oesophageal stents are meshed tubular implants designed to maintain patency of the oesophageal lumen and attenuate the symptoms of oesophageal cancer. Oesophageal cancers account for one in twenty cancer diagnoses and can lead to dysphasia, malnutrition and the diminishment of patient quality of life (QOL). Self-expanding oesophageal stents are the most common approach to attenuate these symptoms. Recent advances in oncological therapy have enabled patient survival beyond the lifetime of current devices. This introduces new complications for palliation, driving the need for innovation in stent design. This review identifies the factors responsible for stent failure. It explores the challenges of enhancing the longevity of stent therapies and outlines solutions to improving clinical outcomes. Discussions focus on the role of stent materials, construction methods, and coatings upon device performance. We found three key stent enhancement strategies currently used; material surface treatments, anti-migratory modifications, and biodegradable skeletons. Furthermore, radioactive and drug eluting stent designs were identified as emerging novel treatments. In conclusion, the review offers an overview of remaining key challenges in oesophageal stent design and potential solutions. It is clear that further research is needed to improve the clinical outcome of stents and patient QOL.

Side-branch expansion capacity of contemporary DES platforms

BackgroundPercutaneous coronary interventions (PCI) of bifurcation stenoses are both complex and challenging. Stenting strategies share that the stents’ side cells must be carefully explored and appropriately prepared using balloons or stents. So far, stent manufacturers have not provided any information regarding side-branch expansion capacity of their stent platforms.AimsGiven that drug-eluting stent (DES) information regarding their mechanical capacity of side-branch expansion is not available, we aimed to evaluate contemporary DES (Orsiro, BIOTRONIK AG; Xience Sierra, Abbott Vascular; Resolute Integrity, Medtronic; Promus Premier Select, Boston Scientific; Supraflex Cruz, Sahajan and Medical Technologies) by their side-branch expansion behavior using in vitro bench testing.MethodsIn this in vitro study, we analyzed five commercially available DES (diameter 3.0 mm), measuring their side-branch expansion following inflation of different high-pressure non-compliant (NC) balloons (balloon diameter: 2.00–4.00 mm), thereby revealing the morphological characteristics of their side-branch expansion capacities.ResultsWe demonstrated that all tested contemporary DES platforms could withstand large single-cell deformations, up to 4.0 mm. As seen in our side-branch experiments, DES designs consisting of only two connectors between strut rings did not only result in huge cell areas, but also in larger cell diameters following side-branch expansion compared with DES designs using three or more connectors. Furthermore, the stent cell diameter attained was below the balloon diameter at normal pressure.ConclusionsWe recommend that the expansion capacity of side-branches should be considered in stent selection for bifurcation interventions.

Factors Influencing Stent Failure in Chronic Total Occlusion Coronary Intervention.

Stent failure remains one of the greatest challenges for interventional cardiologists. Despite the evolution to superior second- and third-generation drug-eluting stent designs, increasing use of intracoronary imaging and the adoption of more potent antiplatelet regimens, registries continue to demonstrate a prevalence of stent failure or target lesion revascularisation of 15–20%. Predisposition to stent failure is consistent across both chronic total occlusion (CTO) and non-CTO populations and includes patient-, lesion- and procedure-related factors. However, histological and pathophysiological properties specific to CTOs, alongside complex strategies to treat these lesions, may potentially render percutaneous coronary interventions in this cohort more vulnerable to failure. Prevention requires recognition and mitigation of the precipitants of stent failure, optimisation of interventional techniques, including image-guided precision percutaneous coronary intervention, and aggressive modification of a patient’s cardiovascular risk factors. Management of stent failure in the CTO population is technically challenging and itself begets recurrence. We aim to provide a comprehensive review of factors influencing stent failure in the CTO population and strategies to attenuate these.

Assessment of a mathematical model considering the effect of flow rate on in-vitro drug-release from PLGA films

Drug-eluting stents implanted in blood vessels are subject to various dynamics of blood flow. In this study, we present the evaluation of a mathematical model considering the effect of flow rate, to simulate the kinetic profiles of drug release (Diclofenac Sodium (DS)) from in-vitro from PLGA films. This model solves a set of non-linear equation for modeling simultaneously the burst, diffusion, swelling and erosion involved in the mechanisms of liberation. The release parameters depending on the flow rate are determined using the corresponding mathematical equations. For the evaluation of the proposed model, test data obtained in our laboratory are used. To quantify DS release from drug-carrier PLGA films, we used the flow-through cell apparatus in a closed-loop. Four flow rate values are applied. For each value, the model-substance liberation kinetics showed an increase in drug released with the flow rate. The simulated release profiles show good agreement with the experimental results. Therefore, the use of this model could provide a practical tool to assess in-vitro drug release profiles from polymer matrices under continuous flow rate constraint, and could help improve the design of drug eluting stents.

CRT-100.89 DynamX Bioadaptor, A Novel “Uncaging” Platform for Coronary Artery Revascularization: 12-Month Clinical and Imaging Results

Drug-Eluting Stents (DES) are the mainstay of coronary artery disease treatment. Although DES design iterations have reduced MACE in the first year after PCI, beyond 1-year, a persistent 2-3% annualized event rate without plateau is observed. The DynamX™ Novolimus-Eluting Coronary Bioadaptor

Drug-eluting stent specifically designed to target vascular smooth muscle cell phenotypic modulation attenuated restenosis through the YAP pathway

Vascular smooth muscle cell (SMC) phenotypic modulation contributes to the development of restenosis. A sorafenib-eluting stent was specifically designed to target SMC phenotypic modulation to inhibit in-stent restenosis in the present study. SMC contractile protein from the freshly isolated rat aorta was expressed at a high level, but its expression was dramatically reduced after SMCs were cultured in 10% FBS for 1 wk. After sorafenib treatment, SMC contractile protein expression was markedly upregulated. We further observed that Yes-associated protein (YAP) expression was attenuated after sorafenib treatment in a dose-dependent manner. Overexpression of YAP by lentivirus reversed the expression of sorafenib-induced SMC contractile protein and increased the expression of cyclin D. Mechanistically, sorafenib regulated the serum response factor-myocardin (SRF-Myocd) complex through competitive binding of YAP to Myocd and increased SRF binding to CArG-containing regions of SMC-specific contractile genes within intact chromatin, thereby controlling the activity of smooth muscle-specific gene transcription. In a rabbit carotid model, the sorafenib-eluting stent (SFES) dramatically inhibited in-stent restenosis and upregulated SMC contractile protein expression. Overexpression of YAP blocked the antirestenosis effect of SFES and repressed contractile smooth muscle-specific genes in vivo, indicating that SFES attenuated in-stent restenosis through YAP-mediated SMC phenotypic modulation. We demonstrated that SFES attenuated in-stent restenosis through YAP-mediated SMC phenotypic modulation. Targeting SMC phenotypic modulation by drug-eluting stent represents an attractive therapeutic approach for the treatment of occlusive vascular diseases.NEW & NOTEWORTHY In the present study, we demonstrated that sorafenib regulates smooth muscle cell (SMC) phenotypic modulation from a proliferative to a contractile state. Sorafenib induced a myocardin-serum response factor interaction and increased SMC contractile gene transcription through the Yes-associated protein pathway. Moreover, local delivery of sorafenib regulating SMC phenotypic modulation represents a promising strategy in the design of drug-eluting stents.

Defining drug and target protein distributions after stent-based drug release: Durable versus deployable coatings

BackgroundInnovations in drug eluting stent designs make it increasingly important to develop models for differentiating performance through spatial definition of drug, receptor binding and cell state. MethodsTwo designs of sirolimus analog eluting stents were implanted into porcine coronary arteries for 28, 60 or 90 days (n = 9/time point), durable coating (Xience) and deployable absorbable coating (MiStent). Explanted arteries were evaluated for drug content (n = 3/time point) by LC-MS/MS and for drug and target protein (mTOR) distributions by immunofluorescence (IF, n = 6/time point). A computational model was developed to predict drug release and arterial distribution maps. ResultsBoth stents released the majority of drug load by 28 days, with different tissue retention efficiencies (91.4 ± 4.9% MiStent versus 21.5 ± 1.9% Xience, P < 0.001). Computational modeling of MiStent coating deployment and microcrystal dissolution recapitulated in vivo drug release and net tissue content and predicted that >98.5% of deployed drug remains crystalline through 90 days. Immunofluorescence and computational modeling showed peristrut drug localization for both stents, with similar peaks, but high interstrut levels only at sites of coating deployment from the absorbable coating. Co-localization of mTOR-IF with drug-IF for both devices showed persistent drug effects, though with differential drug–receptor pharmacokinetics. ConclusionsImmunofluorescence and computational modeling provide insights into drug distribution and binding status that can help differentiate drug delivery technologies. Herein we found that tissue deployment of slow dissolving crystalline drug particles results in temporally and spatially more uniform drug delivery to interstrut zones that might otherwise be under-dosed without excess peristrut drug.

Treatment of Coronary Artery Disease: Randomized Trials on Myocardial Revascularization and Complete Arterial Bypass Grafting

Friedrich Wilhelm Mohr from the very beginning of his career as a cardiac surgeon was involved in the refinements of coronary artery bypass grafting (CABG). At the Leipzig Heart Center, his spirit of early adapting to new technologies inspired the entire team and led to a matchless scientific atmosphere to find solutions to improve almost all fields of cardiac surgery, including CABG. In combination with a tremendous number of patients with indications for isolated coronary artery bypass Prof. Mohr as the surgical principle investigator and the Leipzig Heart Center were able to include patients in the Synergy between PCI [percutaneous coronary intervention] with Taxus and Cardiac Surgery (SYNTAX) trial, the first randomized trials comparing CABG and PCIs using the drug-eluting stents. Final SYNTAX results after 5 years gave direction and scientific evidence for contemporary European revascularization guidelines. These guidelines recommend PCI as an alternative first-line treatment option in patients with coronary three-vessel disease and left main stenosis having low coronary complexity based on the angiographic SYNTAX score. However, the study demonstrated the significant superiority of CABG over PCI in all other patients, especially in these with complex three-vessel disease. The specific characteristic of the SYNTAX study is that the distinguished results were confirmed by several post-SYNTAX comparative randomized trials on coronary revascularization including left main disease and clinical registries even when contemporary drug-eluting stent designs were used. When performing CABG the question of the best second graft remains unclear. While several mono-institutional reports and large meta-analyses demonstrated clear superiority in terms of long-term survival when using bilateral mammary versus single mammary revascularization, this benefit could not be confirmed in randomized trials after 5 years.

Safety and efficacy of a novel abluminal groove-filled biodegradable polymer sirolimus-eluting stent.

Late stent thrombosis (LST) following drug-eluting stent (DES) implantation in patients with coronary artery disease (CAD) is often associated with delayed vascular healing, resulting from vascular inflammation and hypersensitivity to durable polymers and drugs. Therefore, DES design, materials, and coatings have been technologically revolutionized. Herein, we designed a novel abluminal groove-filled biodegradable polymer sirolimus-eluting stent (AGF-BP-SES), with a sirolimus content of only about one-third of traditional DES. The mechanical performances of AGF-BP-SES during compression and expansion were investigated. The pharmacokinetic (PK) profile of sirolimus was studied in the swine model. The in vivo efficacy of AGF-BP-SES was compared with that of Xience PRIME® stent. The results showed that AGF-BP-SES exhibited mechanical properties similar to traditional DES, including the rebound ratio of radial contraction/direction, rebound ratio of axial contraction/direction, and inhomogeneity of compression/expansion. Despite utilizing a reduced dose of sirolimus, AGF-BP-SES delivered sirolimus to the coronary artery in a controlled and efficient manner. The stent maintained a safe and effective local drug concentration without local or systemic risks. In the swine model, histopathological indicators predicted safety and biocompatibility of AGF-BP-SES. In conclusion, AGF-BP-SES maintained similar mechanical properties as other stents while reducing the drug-loading capacity, and showed a favorable safety and efficacy profile of the targeted DES.

Tracking delivery of a drug surrogate in the porcine heart using photoacoustic imaging and spectroscopy.

Although the drug-eluting stent (DES) has dramatically reduced the rate of coronary restenosis, it still occurs in up to 20% of patients with a DES. Monitoring drug delivery could be one way to decrease restenosis rates. We demonstrate real-time photoacoustic imaging and spectroscopy (PAIS) using a wavelength-tunable visible laser and clinical ultrasound scanner to track cardiac drug delivery. The photoacoustic signal was initially calibrated using porcine myocardial samples soaked with a known concentration of a drug surrogate (DiI). Next, an in situ coronary artery was perfused with DiI for 20 min and imaged to monitor dye transport in the tissue. Finally, a partially DiI-coated stent was inserted into the porcine brachiocephalic trunk for imaging. The photoacoustic signal was proportional to the DiI concentration between 2.4 and 120 ?? ? g / ml , and the dye was detected over 1.5 mm from the targeted coronary vessel. Photoacoustic imaging was also able to differentiate the DiI-coated portion of the stent from the uncoated region. These results suggest that PAIS can track drug delivery to cardiac tissue and detect drugs loaded onto a stent with sub-mm precision. Future work using PAIS may help improve DES design and reduce the probability of restenosis.

Poly(styrenesulfonate)-Modified Ni-Ti Layered Double Hydroxide Film: A Smart Drug-Eluting Platform.

Drug-eluting stents (DESs) are widely used in the palliative treatment of many kinds of cancers. However, the covered polymers used in DESs are usually associated with stent migration and acute cholecystitis. Therefore, developing noncovered drug-loading layers on metal stents is of great importance. In this work, Ni-Ti layered double hydroxide (Ni-Ti LDH) films were prepared on the surface of nitinol via hydrothermal treatment, and the LDH films were further modified by poly(styrenesulfonate) (PSS). The anticancer drug doxorubicin could be effectively loaded onto the modified films, and drug release could be smartly controlled by the pH. Besides, the drug absorption amounts of cancer cells cultured on the films could be effectively improved. These results indicate that the PSS-modified LDH film may become a promising drug-loading platform that can be used in the design of DESs.

Late and Very Late Stent Thrombosis in the Era of Second-Generation Drug-Eluding Stents

Stent thrombosis is a life-threatening complication of percutaneous coronary intervention that often results in ST-segment myocardial infarction or sudden cardiac death. First-generation drug-eluting stents (DESs) are associated with an increased risk of late and very late stent thrombosis compared with bare- metal stents due to delayed endothelialisation of the stent struts. The second-generation DES design includes a number of improved features (thinner stent struts, fluorinated copolymers, and different anti-proliferative agents) to decrease the risk of late stent thrombosis. Currently, the cobalt-chromium everolimus-eluting stent, a second-generation stent, has the lowest risk of stent thrombosis when compared with the available alternatives. Given the improved design of second-generation stents, a shorter duration of dual antiplatelet therapy of 6 months may be enough to reduce the rate of bleeding complications without increasing the risk of adverse cardiovascular events. Future large-scale randomised trials are required to evaluate the safety and efficacy of third-generation DESs which feature bioresorbable polymers and scaffolds.

Evolution of Drug-Eluting Stent Drug Elution Profile: Is a Crystalline Drug Form the Ideal Solution?

Since its introduction into clinical practice, coronary angioplasty has seen game-changing advances incomparable to any other medical technology. In particular, the progression from balloon angioplasty to stent technology has not only seen significant advances in technology but, more importantly, improved patient outcomes. The introduction of the drug-eluting stent (DES) has further pushed the technology to a new standard of care. However, even in the current day, top performing DESs still have several limitations. Their safety has been limited by suboptimal polymer biocompatibility, delayed stent re-endothelialisation, and local drug toxicity, leading to adverse clinical outcomes such as very late stent thrombosis, allergic reactions, and chronic inflammation. In addition, current DESs have a consistent yearly increase in late restenosis and revascularisations. Furthermore, durable polymer coatings used in first-generation DESs have been associated with mechanical complications and non-uniform coating, resulting in drug loss and poor distribution. As a consequence, in recent years, the focus of research has been on the development of novel drug carrier systems including absorbable (or biodegradable) polymer coatings and non-polymeric stent surfaces. Additional improvements have included the development of more modern stent platforms. Optimised drug delivery requires a combination of refined stent designs and drug delivery technology. The combination of highly-refined bare-metal stent designs and polymer coating materials have been two areas of focus for the development and improvement of next-generation DESs. Despite all the changes in stent design and polymer materials, there has been little done in the past 15 years to improve drug elution profiles. The need for new advancements in DES design to overcome late event occurrence, and possibly even improve on the clinical outcomes of current DESs, has led to interest in moving away from the standard drug elution profile to explore alternatives. A new manufacturing technique that may have overcome traditional limitations has led to the development of a novel stent platform. This review will explore the principles, device technology, and clinical data to date on a crystalline form of the anti-restenotic drug for stent implantation. This approach could truly be game changing due to an improved elution pharmacokinetic profile, as well as reduced local toxicity and improved long-term biologic arterial wall response.