Drop In Resistance Research Articles

Transient Structural Transition in Ovonic Threshold Switching Glass

AbstractOvonic threshold switching (OTS), characterized by a rapid resistance drop in chalcogenide glass, has enabled the realization of memory and selectors. Despite over five decades of development, the challenges in characterizing the transient switching in amorphous materials upon reaching the threshold voltage have hindered the establishment of its underlying mechanism. This study uses femtosecond terahertz spectroscopy and ab initio simulation to elucidate the dynamics of the free‐carrier and IR‐active phonons involved in OTS. Specifically, in Te‐rich amorphous GeTe, the generation of transient phonons is observed within picoseconds, a phenomenon associated with an increased Born effective charge due to the alignment of Te‐centered bonds. The findings demonstrate a correlation between the enhancement of polarizability, due to orbital alignment during the disorder–order structural transition while maintaining a macroscopic amorphous structure, and the switching behavior. These results provide valuable insights into the enigmatic OTS phenomenon.

Large photoresistance and photoinduced magnetoresistance in La0.67Ca0.33MnO3 thin film on silicon substrate

Abstract The effects of light illumination and magnetic field on the electrical transport properties of La0.67Ca0.33MnO3 thin film on a silicon substrate have been studied in detail. Large value of colossal magnetoresistance has been observed under an applied magnetic field in the whole temperature range below 150 K which is related to the presence of both antiferromagnetic and ferromagnetic phase in the sample. A significant amount of resistance drop is caused by light illumination even at extremely low light intensities, ∼−22% with light of 0.3 μW cm−2 intensity and ∼−42% with 6.2 μW cm−2 intensity at 600 nm wavelength. There has been a notable rise in the photoinduced magnetoresistance value, specifically, a significant decrease in resistance occurs in simultaneous presence of magnetic field and light. For 1 T applied magnetic field, MR% rises from −33% in dark to −58% under light illumination at 150 K i.e. ΔMR% is 25%. As the strength of the magnetic field increases, ΔMR% decreases, suggesting that the magnetoresistive photoinduced phenomenon is more pronounced in the presence of mix phases in the sample. This combined enhanced magnetoresistive photoinduced phenomenon is explained by the interaction of photogenerated charge carriers in the sample and applied magnetic field.

Anomalous influence of electrode width on the critical current of Nb/Au Josephson junctions

Abstract We study the effect of electrodes width on superconducting current transport in Nb-Au-Nb Josephson bridges. The critical current as well as the normal bridge resistance drop with decreasing electrode width on scales of a few μm, which are orders of magnitude larger than the estimated coherence length of Au strip. We consider several physical reasons of such an anomalous influence of the width W of the superconducting electrode on the critical current Ic (AIWIc) and provide model fits for the resistive and superconducting properties of the bridges. {The smooth dependence of the Nb-Au-Nb bridge parameters on the electrode width can be used to optimize the design of superconducting devices for specific applications.

Thermal modelling and layout optimization of GaN half-bridge IC with integrated drivers and power HEMTs

The paper presents the results of thermal modeling of a half-bridge monolithic integrated circuit (IC) with integrated drivers and enhanced mode power high electron mobility transistors, based on a GaN-on-SOI heterostructure. It had been established that the main heat sources in the IC were the half-bridge GaN HEMTs. The heat from the half-bridge GaN HEMTs propagates in the chip and leads to heating of the logic block and gate drivers. Heating of half-bridge GaN HEMTs leads to increased channel resistance and IC output current drop. Heating of the gate drivers reduces driving current, as a result, increases the switching time of the half-bridge GaN HEMTs. Heating of the logic block increases the rise and fall times of the generated control signals, which worsens the dynamic characteristics of the IC. A comparative analysis of heat propagation for IC dies based on GaN-on-SOI and GaN-on-Si heterostructures showed that GaN-on-SOI structure has a 40% greater junction-to-backside thermal resistivity compared to GaN-on-Si structure. In this case, the specific thermal resistance in the direction of heat propagation from the hotspot of the transistor to the backside of the die for the GaN-on-SOI structure is almost two orders of magnitude greater than in the direction of its propagation to the frontside of the chip. The results obtained were used for IC layout optimization. The rearrangement of GaN-on-SOI IC functional blocks, as well as to introduction of additional heat-spreading elements on the frontside of chip were carried out during the optimization.

Effect of solutions acidity on Haacke’s Figure of Merit of ZnO and ZnO:F thin films deposited by ultrasonic spray pyrolysis

Fluorine-doped zinc oxide (ZnO:F) thin films are valued for their potential as transparent conductive materials, particularly in optoelectronic applications. In this work, the deposition of highly conductive and transparent fluorine-doped ZnO thin films, deposited by chemical spray on glass substrates is reported. The effect of acetic (AcAc) in the initial fresh solution on Haacke’s Figure of Merit (Φ) of both zinc oxide (ZnO) and fluorine-doped zinc oxide (ZnO:F) thin films was studied. The substrate temperature was fixed to 450°C, and two deposition times (8 and 14 min) were tested. Accordingly, the optical and transport properties, as well as the structural and morphological characteristics of the films were measured. The results indicate that the samples are polycrystalline in all cases and exhibit a wurtzite-type structure of ZnO. The variation of AcAc in the starting solution causes a switch in preferential growth from (002) to (001). As the AcAc content increases, the surface morphology of the films reveals the formation of well-defined hexagonal grains, and the grain size increases. Conversely, the transmittance decreases as the acetic acid increases, which can attributed to carbon incorporation into the film. In addition, the band gap values of the films varied from 3.2 to 3.4 eV. Also, as the acetic acid concentration increased, a drop in the electrical resistivity of ZnO thin films on the order of 0.016 Ω⋅ cm was found for the ZnO:F films deposited with fresh solution for 14 min. This can be ascribed to a dense acetic cloud formed during the synthesis process, trapping volatile F species that incorporate into the ZnO lattice. This enhances Haacke’s Figure of Merit of ZnO:F films deposited with a fresh solution, demonstrating their potential use for application as transparent conductive films. This contrasts with other synthesis methods that require longer aging time in the precursor solution, making these findings useful for large-scale and more efficient production of transparent conductive films.

Impact of Nickel Strip Configurations on Resistance and Voltage Drop in Lithium Ion Battery Packs

The impact of nickel strip designs on the resistance and voltage drop in lithium ion battery packs is examined in this study. In a series parallel battery pack configuration, the effectiveness of coated and pure nickel strips is assessed, with particular attention paid to how they influence voltage drop, internal resistance, and overall efficiency. Each of the 24 series and 3 parallel cells that make up the battery pack has an internal resistance of 6 mΩ. Two configurations are analyzed: one utilizing pure nickel strips and another with coated nickel strips. The resistivity, cross sectional area, and length of the material are used to compute the equivalent resistance of the nickel strips for each arrangement. Voltage dips at a load current of 50A are determined to compare the performance of both strip. The study also looks at the voltage drop at key locations in the battery pack, including particular bent strips. The findings show that the coated nickel design displays a larger resistance (0.237Ω) and voltage drop (11.735V) than the pure nickel configuration, which has a lower total resistance (0.048Ω) and voltage drop (2.82V). Evaluation of the voltage drop during charging is also done for charging currents of 6A and 10A, demonstrating that the pure nickel arrangement allows for more efficient charging. One of the main elements affecting battery pack performance is internal resistance, which has a direct impact on the system's voltage drop and overall energy efficiency. The thickness, width, resistivity, and number of parallel strips utilized in this nickel strip material all have a major effect on the battery pack's total resistance. Because of this, the nickel strip design can improve or worsen the pack's power delivery, particularly in high load scenarios.

Investigation of the electrical quality and long-term stability of aluminum ground stud connections in automotive applications

The rapid advancement in the electrification of modern vehicles has led to a continuous increase in electrical consumers for various comfort and safety functions. Ground studs serve as the electrical interface between the conductive vehicle body and the onboard network. Drawn arc stud welding is an economical and established joining process for producing ground stud joints. The circuits in the onboard network are increasingly subject to greater demands regarding current-carrying capacity and long-term stability. Reliable signal and power transmission require minimal contact resistance at the electrical connection points of the ground stud system and must withstand various operating and environmental conditions over the entire service life. In this study, a ground stud made of AlMg5, with a ZnNi-coated steel cap nut was used on a 2.0 mm thick sheet of AlMg3. The electrical connection of the ground studs was made using tinned copper cable lugs and 35 mm² cables. To analyze the electrical resistance behavior in an accelerated test, the ground studs were subjected to a superimposed load with a cyclic current profile for 1008 hours under changing climatic conditions. The results show that under the chosen operational and environmental conditions, accelerated aging and intermittent resistance behavior occur. A characteristic drop in resistance during the test indicates the failure point of the electrical connection. The cause of failure can be attributed to media penetration into the electrical contact zone. A failure of the electrical connection was observed after 512 hours.

Experimental investigation into heat transfer and flow characteristics of magnetic hybrid nanofluid ([formula omitted]/Ti[formula omitted]) in turbulent region

Extensive research and empirical evidence demonstrate the superior thermal performance of nanofluids compared to DIW. Magnetic hybrid nanofluids, such as Fe3O4/TiO2, are currently being explored for their enhanced thermal properties. This study evaluates Fe3O4/TiO2 nanofluids for heat transfer and hydraulic resistance across Reynolds numbers from 3200 to 5300 and volume fractions from 0.00625 % to 0.3 % vol. UV–Vis spectroscopy shows that lower volumetric fractions correlate with decreased sedimentation. Over 30 days, nanofluids with 0.3 % vol, 0.2 % vol, and 0.1 % vol exhibited high sedimentation factors (SF) of 31.79 %, 11.88 %, and 11.44 %, respectively, while 0.00625 % vol, 0.0125 % vol, and 0.025 % vol demonstrated better stability with SFs of 8.89 %, 9.82 %, and 10.24 % respectively. Volume fractions significantly impact heat transfer, with CHT coefficients increasing by 11.42 % at 0.3 % vol, 14.03 % at 0.2 % vol, 18.04 % at 0.1 % vol, and 19.98 % at 0.05 % vol. The greatest enhancements are at lower concentrations: 22.91 % at 0.025 % vol, a peak of 26.33 % at 0.0125 % vol, and 24.30 % at 0.00625 % vol. Pressure drops are highest at 21 % for 0.3 % vol at Re 5018, decreasing with lower concentrations: 13.10 % at Re 5144.4 (0.2 % vol), 11.94 % at Re 5041.6 (0.1 % vol), 9.82 % at Re 5112.2 (0.05 % vol), 7.67 % at Re 5258.7 (0.0125 % vol), and 10.29 % at Re 5094.0 (0.00625 % vol). These results highlight that higher nanoparticle concentrations increase pressure drop, impacting energy efficiency. Lower concentrations (0.0125 % Vol and 0.00625 % Vol) provided better heat transfer with lower pressure losses. Total Efficiency Index (TEI), The optimal nanoparticle concentration for maximum thermal efficiency was approximately 0.0125 % Vol. TEI values were highest at this concentration, indicating enhanced heat transfer with minimal thermal resistance and pressure drop. Higher concentrations (0.2 % Vol and 0.3 % Vol) showed lower TEI values, suggesting reduced thermal efficiency due to increased flow resistance. These findings highlight the importance of selecting an appropriate nanoparticle concentration to optimize thermal performance in heat transfer systems, balancing the benefits of enhanced heat transfer with the drawbacks of higher-pressure losses.

Three-dimensional numerical investigation on flow and heat transfer characteristics and multi-objective optimization of interconnected microchannels

The interconnected microchannel demonstrates excellent performance in enhancing flow heat transfer. However, the optimal width of the interconnecting slot has not been thoroughly investigated. To address this gap, this paper numerically simulates the three-dimensional flow and heat transfer of interconnected microchannels featuring varied slot widths and channel depths. The investigated slot widths range from 50 to 1000 μm and depths of 100, 200, and 300 μm. Evaluation of overall performance encompasses heat transfer and flow characteristics such as average wall temperature, heat transfer coefficient, thermal resistance as well as pressure drop. It is the interconnected slots that interrupt the velocity and thermal boundary layers, contributing to enhanced heat transfer. Furthermore, the back propagation neural network and non-dominated sorting genetic algorithm-II are utilized for multi-objective optimization of thermal resistance and pressure drop. The technique for order preference by similarity to an ideal solution (TOPSIS) method combined with the entropy weight method is employed to select the compromise optimal solution from the Pareto optimal solutions. The optimized slot widths are 369, 424, and 167 μm for channel depths of 100, 200, and 300 μm, respectively. This research provides data support for the optimization design and engineering manufacturing of interconnected microchannels.

Accessing bands with extended quantum metric in kagome Cs 2 Ni 3 S 4 through soft chemical processing

Flat bands that do not merely arise from weak interactions can produce exotic physical properties, such as superconductivity or correlated many-body effects. The quantum metric can differentiate whether flat bands will result in correlated physics or are merely dangling bonds. A potential avenue for achieving correlated flat bands involves leveraging geometrical constraints within specific lattice structures, such as the kagome lattice; however, materials are often more complex. In these cases, quantum geometry becomes a powerful indicator of the nature of bands with small dispersions. We present a simple, soft-chemical processing route to access a flat band with an extended quantum metric below the Fermi level. By oxidizing Ni-kagome material Cs 2 Ni 3 S 4 to CsNi 3 S 4 , we see a two orders of magnitude drop in the room temperature resistance. However, CsNi 3 S 4 is still insulating, with no evidence of a phase transition. Using experimental data, density functional theory calculations, and symmetry analysis, our results suggest the emergence of a correlated insulating state of unknown origin.

New training simulator for lumbar puncture base on magnetorheological

In response to the difficulties in accurately reproducing the resistance drop generated by puncturing key tissue layers with a needle and the poor experience in existing simulators, based on the continuous controllability and rapid response of magnetorheological fluid under the influence of a magnetic field, this paper proposes a lumbar puncture training simulator(LPTS) that can accurately simulate the puncture feedback force within tissues such as the skin, subcutaneous fat, and supraspinous ligament throughout the entire process. By using a dual rod structure and reasonably arranging the damping channel gap, the influence of mechanical friction and zero-field damping force on the feedback force during tissue progression is minimized. This paper introduces the acquisition and modeling analysis of raw data, and based on this, the design, simulation, and mechanical testing of the simulator are carried out. Finally, a performance testing platform for the simulator is established to evaluate its tracking performance of the expected puncture strength and the reproducibility of the puncture sensation. The results show that the experimental puncture strength deviates from the expected puncture strength by 0.35 N to 0.61 N in the crucial steps of breaking through the supraspinous ligament, interspinous ligament, ligamentum flavum, and dura mater, with a relative error below 10 %.

Flexible transparent conductors with a percolated Ag nanostructure and its application as efficient self-bias plasmonic photodetector

A percolated silver (Ag) nanostructured-based transparent conductor has been deposited by physical vapor deposition (PVD) technique where lateral growth of Ag has been enhanced by a pre-deposited Ag-TiO2 thin film. This Ag-TiO2 film has embedded Ag nanoparticles (NPs) within TiO2 thin film which is grown in a low temperature (100 °C) solution processed technique. This process includes Li4Ti5O12 (LTO) thin film deposition by a sol–gel method followed by ion-exchange (Li+ → Ag+) process to yield an Ag-TiO2 thin film. The percolated Ag network has appeared as soon film mass-thickness reaches close to 10 nm, resulting in an abrupt drop of electrical resistivity of the film. This percolated Ag nanostructured thin film (10 nm Ag/Ag-TiO2/plastic) has resistivity of ∼50 Ω/□ and an average visual transmittance of >70 % up to 450 nm. In higher wavelength range, transparency gradually reduces, and it reaches to ∼50 % at 600 nm which is mostly due to the plasmon absorption of this film. By utilizing its combined optical transparency and surface plasmon absorption, this film has been used to develop plasmonic hot electron photodetectors where Ag-thin film works as transparent electrode as well as plasmon induced photo-excited hot electron generation. Device has been fabricated on a heavily doped n type Si (n++-Si) with a metal–semiconductor-metal (M−S−M) device geometry. External quantum efficiency (EQE) data reveal that photocurrent of this device is mostly generated in the plasmonic absorption region with a peak detectivity of 2.84 × 1012 Jones at 510 nm under −3V external bias. Besides, the device shows fast response with a response time of ∼25 ms.

Unveiling a Novel Insulator-to-Metal Transition in La2NiO4+δ: Challenging High-Temperature Superconductivity Claimed for Single-Layer Lanthanum Nickelates

Abstract La2NiO4 has a similar structure to La2CuO4 and was proposed as a high-temperature superconductor based on magnetic-moment measurements decades ago. Nevertheless, with the exception for electrical resistance drop behavior of about 4 orders of magnitude that is claimed to originate from the superconductivity ever observed in Sr-doped La2NiO4, most electrical data reported to date in La2NiO4 system exhibit a trivial insulating ground state. Here, we definitively identify the similar electrical resistance drop behavior of more than 3 orders of magnitude in La2NiO4+δ . However, our extensive investigations reveal that this phenomenon is a novel insulator-to-metal transition, distinct from superconductivity. Intriguingly, compared to the weak magnetic-field effects, pressure can significantly suppress the transition and transform from the metallic to an insulating ground state, accompanied by an isostructural phase transition. Our work not only elucidates the fundamental properties of the metallic conducting ground state in La2NiO4+δ , but also critically challenges the notion of superconductivity in single-layer lanthanum nickelates.

Advancing cryogenic electronic cooling: A case study on embedded manifold microchannels in micromachined Joule-Thomson coolers

Thermal management plays a crucial role in the performance of electronic devices. For devices operating at room temperatures, manifold microchannels (MMCs) are essential for heat dissipation in heat sinks due to their low thermal resistance and pressure drop. However, their application in cryogenic electronic devices to enhance thermal performance has been largely unexplored. Herein, we integrated manifold microchannels into the evaporator of a micromachined Joule-Thomson (MJT) cooler to improve its cooling performance. The results show a notable reduction in the minimum cooling temperature from 105.0 K to 95.3 K, accompanied by an approximate 20 % increase in maximum cooling power. Furthermore, the coefficient of performance (COP) exhibits a rise of over 20 %. These findings underscore the feasibility and effectiveness of using MMCs in cryogenic electronic devices.

Study on the changing law of three-dimensional electric field during the evolution of seepage field in earth and rock embankment dams

Seepage is a common disease of earth and rock embankment dams, but due to the complex geological conditions, its location and seepage diameter are more difficult to be accurately detected. In order to accurately determine the seepage damage state of earth and rock dam materials during the evolution of seepage field, and to clarify the change rule of three-dimensional electric field of earth and rock embankment dams during the evolution of seepage field, this paper establishes a correlation model between seepage field and electric field based on porosity. Based on the model, the relationship between resistivity and critical hydraulic ratio drop during the infiltration damage of soil and rock dam is determined, focusing on the study of the three-dimensional electric field in the infiltration process of soil and rock dam body with the seepage field change characteristics and change rules, and obtaining the electric field response characteristics of the seepage field of the different hidden bodies, which provides a diagnostic basis for the realization of the subsequent leakage diagnostic technology of soil and rock dams.

Multiphase superconductivity at the interface between ultrathin FeTe islands and Bi2Te3

FeTe monolayer islands situated on a topological insulator Bi2Te3 (0001) surface were recently reported to exhibit the opening of an energy gap below temperatures T ~ 6 K, which could be due to a superconducting phase transition. In this work, we present a magnetic field dependent transport study proving that this gap is indeed of superconducting origin. Upon cooling, several drops in resistance are observed in the temperature range between 6 K and 2 K, indicating multiple transitions. Using the Ginzburg-Landau theory, we show that the critical magnetic field of the dominant high-temperature transition at ~ 6 K is governed by orbital Cooper pair breaking in larger FeTe islands, large enough to exceed the superconductive coherence length ξ\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\xi$$\\end{document}. At smaller island sizes, transitions at lower temperatures < 6 K become more prominent, showing significantly increased critical fields dominated by paramagnetic pair breaking. The multiphase superconducting behaviour is in line with an observed wide distribution of FeTe islands width 5–100 nm and seems to reflect disorder effects at the interface to Bi2Te3. The proof of local superconductivity makes the FeTe interface to the topological insulator Bi2Te3 substrate a potential host of topological superconductivity.

Effect of temperature on the stability and performance of III-nitride HEMT magnetic field sensors

The study aimed to investigate the underlying physics limiting the temperature stability and performance of non-surface passivated Al0.34Ga0.66N/GaN Hall effect sensors, including contacts, under atmospheric conditions. The results obtained from analyzing the microstructural evolution in the Al0.34Ga0.66N/GaN Hall sensor heterostructure were found to correlate with the electrical performance of the Hall effect sensor. High-resolution x-ray photoelectron spectroscopy studies revealed the signature of surface oxidation in the GaN cap layer, as well as a slight out-diffusion of “Al” from the AlGaN barrier layer. To prevent the formation of a bumpy surface morphology at the Ohmic contact, we investigated the impact of “Pt” top Ohmic contacts. The application of a top “Pt” contact stack resulted in a smooth Ohmic contact surface and provided evidence that the bumpy surface morphology in Au-based Ohmic contacts is due to the formation of an Al-Au viscous alloy during rapid thermal annealing. In the early stages of thermal aging, the small drop in contact resistivity stabilized with subsequent thermal aging past the initial 550 h at 200 °C. The outcome is that the Al0.34Ga0.66N/GaN Hall effect sensors, even without surface passivation, exhibited a stable response to applied magnetic fields with no sign of significant degradation after 2800 h of thermal aging at 200 °C under atmospheric conditions. This observed stability in the Hall sensor without surface passivation can be attributed to a self-imposed surface oxidation of the cap layer during the early stages of aging, which serves as a protective layer for the device during subsequent extended periods of thermal aging at 200 °C.

Corneal application of SOCS1/3 peptides for the treatment of eye diseases mediated by inflammation and oxidative stress.

Several blinding diseases affecting the retina and optic nerve are exacerbated by or caused by dysregulated inflammation and oxidative stress. These diseases include uveitis, age related macular degeneration, diabetic retinopathy and glaucoma. Consequently, despite their divergent symptoms, treatments that reduce oxidative stress and suppress inflammation may be therapeutic. The production of inflammatory cytokines and their activities are regulated by a class of proteins termed Suppressors of Cytokine Signaling (SOCS). SOCS1 and SOCS3 are known to dampen signaling via pathways employing Janus kinases and signal transducer and activator of transcription proteins (JAK/STAT), Toll-like Receptors (TLR), nuclear factor kappa-light-chain-enhancer of activated B cells (NF-κB), mitogen activated kinase (MAPK) and NLR family pyrin domain containing 3 (NLRP3). We have developed cell-penetrating peptides from the kinase inhibitory region of the SOCS1 and SOCS3 (denoted as R9-SOCS1-KIR and R9-SOCS3-KIR) and tested them in retinal pigment epithelium (RPE) cells and in macrophage cell lines. SOCS-KIR peptides exhibited anti-inflammatory, anti-oxidant and anti-angiogenic properties. In cell culture, both Th1 and Th17 cells were suppressed together with the inhibition of other inflammatory markers. We also observed a decrease in oxidants and a simultaneous rise in neuroprotective and anti-oxidant effectors. In addition, treatment prevented the loss of gap junction proteins and the ensuing drop in transepithelial electrical resistance in RPE cells. When tested in mouse models by eye drop instillation, they showed protection against autoimmune uveitis, as a prophylactic as well as a therapeutic. Mice with endotoxin-induced uveitis were protected by eye drop administration as well. R9-SOCS3-KIR was particularly effective against the pathways acting through STAT3, e.g. IL-6 and VEGF-A mediated responses that lead to macular degeneration. Eye drop administration of R9-SOCS3-KIR stimulated production of antioxidant effectors and reduced clinical symptoms in mouse model of oxidative stress that replicates the RPE injury occurring in AMD. Because these peptides suppress multiple pathogenic stimuli and because they can be delivered topically to the cornea, they are attractive candidates for therapeutics for uveitis, macular degeneration, diabetic retinopathy and glaucoma.

Effects of Zr additions and process annealing on mechanical and corrosion properties of AA5383 Al–Mg alloys

Abstract The study investigates how Zr additions and process annealing affect mechanical and corrosion properties of AA5083 Al–Mg alloys by microstructural examination, tensile strength, hardness testing and ASTM G67 nitric acid mass loss test. In the present work, process annealing temperatures were set to 220 °C and 250 °C. The results show that the hardness and tensile properties of Zr-containing cold rolled alloy were superior to that of Zr-free cold rolled alloy before and after process annealing treatment and sensitization heat treatment. Unfortunately, adding Zr to AA5383 alloy significantly degraded the corrosion resistance of the Zr-containing cold rolled alloy annealed at 220 °C. For improving corrosion resistance of Zr-containing alloy, annealing temperature could be increased to 250 °C to avoid a marked drop in the corrosion resistance.

Role of Biofilm Formation in the Drop of Bacterial Resistance to Antibiotics after Animal Therapy with Silver Nanoparticles

Role of Biofilm Formation in the Drop of Bacterial Resistance to Antibiotics after Animal Therapy with Silver Nanoparticles