Double-sided Welding Research Articles

Stepwise double-sided friction stir welding: an alternative for root defect mitigation in aluminium plates with lower gauge numbers

Penetration-induced fractional unbonded defects and flow-induced root flaws are part of the discontinuities of the conventional friction stir welded (FSW’ed) aluminium alloys with limited impact assessment/clarification in literature. The novelty of this study lies in the attempt to eliminate penetration-aided root defect via a stepwise double-sided welding process as well as identify its impact on loadbearing. As a result, the stepwise double-sided FSW welding of a thick aluminium plate (6 mm) was carried out while the microstructure, strength, and fracture modes of the ensuing welds were compared with the conventional (single-sided) friction stir welded counterparts. The stepwise double-sided FSW-welded joint demonstrated better tensile strength relative to the single-sided FSW-welded counterparts owing to its material flow consolidation (two-side deformation) and elimination of penetration-induced fractional unbonded region/root defect. The welding processes do not have a noteworthy influence on the fracture location of the welds as failure ensued via the stir zones of the respective welds. Transient breaking/brittle appearance, and ductile fracture modes were noticed in the single-sided and stepwise double-sided FSW-welded samples respectively. The stepwise double-sided FSW process is recommended as a better choice for thick workpieces relative to conventional FSW to improve the weld’s loadbearing resistance.

Residual stress and deformation of welded T-joint between low carbon steel and stainless steel

The welded structures between carbon steel and stainless steel are widely used in many sectors such as pedestrian bridges, food industry, chemical industry, petroleum, and thermal power plants, … These composite structures take advantages of each material for different parts of structure. In the welded structures between carbon steel and stainless steel, the structure is made by T-joint that is the most common. The calculation of residual stress and welding strain of the T-joint between low-carbon and stainless steel materials is the basis to evaluate the working ability of this structure. In this study, the residual stress and welding deformation of the T-joint are determined by the imaginary force method. The double-sided weld of T-joint between low carbon steel and stainless steel is welded simultaneously by MIG welding process. The obtained results of residual stress and welding deformation in this case are compared with the case of single-sided weld so that we can find the difference between residual stress and welding deformation in two cases.

Investigating the impact toughness properties and influential factors of titanium alloy joints

Double-sided symmetric MIG welding can significantly enhance welding efficiency for thick titanium alloys and holds promising engineering applications. However, the use of high currents and deposition rates in this process not only boosts welding efficiency but also impacts joint performance, particularly its impact toughness. In this study, the Charpy impact performance of double-sided double-arc MIG welded joints in each region was studied via oscillometric impact tests, and the main factors affecting the impact of joints were revealed. Scanning electron microscope was used to observe the fractures, and the microstructure characteristics and grain orientation of the impact crack propagation path were observed and analysed via metallurgical microscopy and EBSD. In addition, the microstructure of each region of the joint was observed via metallographic microscopy and transmission electron microscopy, which revealed the microstructure characteristics of different regions of the joint and clarified the effects of microstructure and grain orientation in different regions of the welded joint on the impact performance of each region of the double-sided, double-arc MIG welded joint. The results show that the crack initiation energy across different regions of joints typically ranges between 18 and 20 J, with minimal variations. Crack propagation plays a pivotal role in determining impact toughness, which is influenced both by microstructural features and orientation. This provides guidance for subsequent adjustments and improvements to the impact performance of the joint.

Numerical prediction and control of deformation and residual stress in double-sided arc welding of large pressure hull

Double-sided arc welding (DSAW), as an advanced connection method, has become a typical method for large pressure hull with thick plates. However, welding deformation and residual stress will seriously affect the dimensional deviation and fatigue life of the product. Therefore, it is a very important work to predict and control the welding deformation and residual stress. A novel dynamic heat distribution model considering the weave of welding torches is proposed to accurately predict DSAW deformation and residual stress in this paper. It is worth noting that this paper also puts forward a method to control the welding deformation and residual stress by flexible constraints of multi-point array, which makes the radial deformation less than 2 mm and the maximum axial stress is 423.98 MPa. This research provides a new idea for the accurate prediction and control of welding deformation and residual stress, which has great engineering significance.

An efficient synergistic double-sided friction stir spot welding method: A case study on process optimization, interfacial characteristics and mechanical properties of 2198-T8 aluminum‑lithium alloy joints

Friction stir spot welding has important applications in the joining of thin metallic plates. However, the asymmetric thermomechanical action inherent in the single-sided friction stir spot welding inevitably generates the hook defect at the joint interface, and the defect deteriorates with the improvement of the interfacial metallurgical bonding, which causes the irreconcilable contradiction and significantly restricts the breakthrough of the process stability and welding efficiency. The synergistic double-sided probeless friction stir spot welding (SDP-FSSW) technology proposed in this study adopts a dual-axis synergistic control system, which introduces intense plastic deformation from both sides of the interface to form a wavy hook by accurate axial motion during the welding process. This innovative process solves the problem of hook warpage while realizing rapid metallurgical bonding and mechanical interlocking at the interface, thus obtaining AA2198-T8 aluminum‑lithium alloy spot joints with a tensile/shear strength exceeding 9kN in a short dwell time (0–3 s). Through response surface methodology, the optimal process parameters are identified, i.e. rotation speed of 603 rpm, dwell time of 3 s, and plunge depth of 0.26 mm, at which condition the average joint strength is 13.0 ± 0.5kN, a 47 % increase compared to an optimized joint of single-sided probeless friction stir spot welding (8.9kN). The optical microscope examination shows that the wavy hook can be adjusted by the rotation speed and the higher rotation speeds will make the wave disappear and produce an approximately straight interface. The fractographic analysis shows that the wavy hook can inhibit crack propagation and has good mechanical interlocking effect, but the flat hook at high rotation speeds leads to crack propagation directly along the interface, and the failure mode is changed from plug-pull fracture to interfacial fracture. Therefore, the joint strength at 1000 rpm is only 7.0kN, which decreases by about 47 % compared with the optimal strength. The electron backscattering diffraction analysis shows that continuous dynamic recrystallization occurs in the hook region and good metallurgical bonding is formed, and there are also some discontinuous dynamic recrystallized grains distributed between the large grains due to the larger strain rates and lower temperature at the interface during the SDP-FSSW process. It has been found that the wavy hook with good metallurgical bonding and mechanical interlocking can be introduced in spot welded joints by controlling the interface forming, which is a viable method to create high quality, efficient and reliable spot joints.

A NOVEL DOUBLE-SIDE LASER WELDED THICK PLATE: MICROSTRUCTURE AND NUMERICAL PREDICTION OF TENSILE TEST

The study aims to provide firsthand knowledge on finite element simulation (FES) of double-side laser welded (LW) stainless steel 304 (SS-304) thick plates used for automobile application. Double-side welding technique is an idea of achieving complete penetration with minimal heat input. The microstructural evaluation revealed the presence of dendritic growth that results in the enhancement of tensile strength (TS) for the welded sample. There is a slight increase in the delta ferrite content in weldment. The change in microstructure is due to thermal history during solidification. The TS of base metal (BM) was [Formula: see text][Formula: see text]MPa whereas the welded sample exhibited strength of [Formula: see text][Formula: see text]MPa. FES was successfully employed to simulate TS with error percentage less than 1.

Influence of welding sequences and boundary conditions on residual stress and residual deformation in DH36 steel T-joint fillet welds

This paper aims to investigate the influence of welding sequences and boundary conditions on welding-induced residual stress and residual deformation of DH36 steel T-joint fillet welds through experimental and numerical methods. A series of typical experiments of successive and simultaneous double-sided welding conditions are conducted to explore both the magnitude and distribution of temperature field, residual stress and residual deformation. Meanwhile, thermal elastic-plastic finite element analysis based on a double ellipsoidal heat source model is performed to investigate the heat transfer and deformation mechanism during the welding process. The influencing factors are further explored to determine and quantify the residual stress and residual deformation induced by different welding sequences and boundary conditions. There is generally well agreement between the experimental and numerical results in terms of temperature field, residual stress, residual deformation and molten pool morphology. The results show that the welding sequences have an important influence on the magnitude and distribution of residual stress and residual deformation. Continuous simultaneous double-sided welding can significantly reduce residual stress and residual deformation to obtain better-quality welds. Boundary conditions have a significant effect on the distribution and magnitude of residual deformation and little effects on residual stress. Tightening the ends of the flange plate with bolts during the welding process can significantly reduce the deformation.

Online welding status monitoring method of T-joint double-sided double arc welding based on multi-source information fusion

In modern manufacturing, double-sided double arc (DSDA) welding brings advantages in properties and efficiency for T-shaped joints. However, the double-side forming makes it difficult to detect the imperfections and ensure weld joint quality, which few studies have covered. Most existing methods deal with single-arc welding with limited sensing sources. To fill the gap, an online welding status monitoring method for DSDA welding is proposed based on the fusion of welding current, arc voltage, arc sound, and weld pool images. In pre-processing, the automatic weld pool region of interest (ROI) detection method based on the lightweight YOLO-L model and the waveform denoising algorithm are designed. In feature engineering, waveform signals are analyzed in both the time and frequency domain. A weld pool feature extractor based on a convolutional neural network (CNN) is proposed with good effectiveness and interpretability. The output feature combination is refined by Fisher-based selection and evaluation. In model building, an ensemble learning model based on three high-fit basic learners is proposed, with an accuracy of 98.538 %. The proposed model shows significant advantages over the single basic classifier and other ensemble methods. Experiments verify high precision and robustness, laying a foundation for accurate real-time monitoring of DSDA welding production.

Residual stress distribution and relaxation in U-rib full penetration welds by ultrasonic impact treatment

Ultrasonic impact treatment (UIT) as an effective method for alleviating welding residual stresses (WRS) is used to improve the fatigue performance of welded structures. However, its application to single- and double-sided U-rib welds in orthotropic decks has been limited. To address this, an experimental and numerical investigation on WRS and UIT was carried out for different deck thicknesses. A 3D thermo-elastic-plastic approach was employed to model the temperature and stress fields by the ABAQUS software. Additionally, a dynamic explicit calculation method was developed to simulate the UIT process, and its accuracy was verified by comparing the actual and numerical grooves and WRS after UIT. Ultrasonic stress measurement was employed to determine the distribution and magnitude of WRS before and after UIT. The results demonstrate that most relative errors of residual stress numerical and test results under different stress paths after UIT are within 10 %, confirming the reliability and effectiveness of this method. For single-sided U-rib welds after UIT, the reduction in WRS at the weld seam ranges from approximately 25.6 % to 87.4 %, while for double-sided U-rib welds, the reduction varies from about 22.2 % to 65.5 %. The impact of UIT on longitudinal residual stresses is more significant compared to its effect on transverse residual stresses. However, UIT results in a relatively smaller reduction in WRS away from the weld seam. Furthermore, it is observed that altering the deck thickness results in different disparities in WRS outcomes after UIT.

Numerical simulation of efficient welding for thick plates in shipbuilding using simufact welding

In the welding process of medium-thick plates, it is common to create grooves and perform double-sided multi-pass welding. However, this approach leads to low welding efficiency and high costs. Hence, this study utilizes a groove-free, double-sided double-pass welding method to enhance welding efficiency and decrease shipbuilding expenses. A finite element model of groove-free submerged arc welding for medium-thick plates was established using SolidWorks software, and mesh division was carried out. Subsequently, numerical simulations of high-voltage, high-current double-sided double-pass submerged arc welding for medium-thick plates were conducted using Simufact Welding software. In the simulation, a mobile double ellipsoid heat source was utilized to replicate the dynamic alterations throughout the entire welding process. Subsequently, the temperature field of the welded material was computed. Finally, utilizing the temperature field results, the residual stress distribution within the welded material was computed through the thermal-structural coupling feature. The simulation results revealed a significant temperature gradient at the center of the heat source during the welding process, with a slower temperature change observed behind the heat source. Around 4000 seconds, the weldment cooled to room temperature. At this point, the thermal stress mainly concentrated around the weld seam. This numerical welding simulation serves as a crucial reference for designing welding process parameters and researching residual stress distribution. Consequently, it enhances welding efficiency in the field of shipbuilding.

Numerical study of full penetration single- and double-sided U-rib welding in orthotropic bridge decks

Under the repeated action of residual stress and wheel load caused by welding, fatigue cracks easily occur on the top plate-U rib welding of an orthotropic bridge deck (OBD). These affect the service life. To study the influence of different full-penetration welding methods on the residual stress and fatigue of OBD, this study compared the residual stress, welding deformation, and fatigue performance of full-penetration single- and double-sided welding through finite element analysis. The welding temperature and residual stress fields were simulated based on Goldak's double ellipsoid heat source model using the thermal elastic-plastic method. The numerical results were verified using measured data from relevant literature, and the two were in good agreement. The results showed that the longitudinal residual stress of the double-sided welded U-rib was larger than that of the single-sided welded U-rib, primarily in the compressive stress range, and the maximum deviation reached 99.44 MPa. The longitudinal displacement of single-sided welding along the weld direction was 0.060 mm lesser than that of double-sided welding, and the maximum vertical displacement perpendicular to the weld direction was 2.457 mm lesser than that of double-sided welding. For the same frequency of fatigue load (wheel load), the fatigue strength of single-sided welding was larger than that of double-sided welding, and the fatigue life increased by 29.7%. In this study, analysis models of the full-penetration single-sided and full-penetration double-sided welding were established, which could provide a reference for structural fatigue assessment using the two full-penetration welding techniques under the influence of residual stress.

The influence of laser separation distance on the mechanical properties of 2219 aluminum alloy T joint in double-sided laser beam oscillation filler welding

The influence of laser separation distance on the mechanical properties of 2219 aluminum alloy T joint in double-sided laser beam oscillation filler welding

Experimental and Numerical Investigation of the Thermal and Force Regulation Mechanism of Bypass Coupling Double-Sided Arc Welding Based on 6061 Aluminum Alloy

In this study, 6061 aluminum alloy was proposed for welding using bypass coupling double-sided arc welding (BCO-DASW) to further improve its welding quality and efficiency. To gain insight into the thermal and force regulation mechanism of the BCO-DASW of 6061 aluminum alloy, the dynamic effects of the high-temperature plasma inside the arc with various parameters were fully compared and investigated through the combined method of the physical experiment and the numerical simulation. The thermal flow field of the hybrid arc was analyzed numerically. Furthermore, its working adaptability and mechanical behaviors were studied experimentally. The results show that a single penetration of the 6 mm sheets can be achieved without visible defects when the center offset of the arcs is within 3 mm on both sides of the base metal during BCO-DASW. Through the thermal analysis, it was found that, compared with the MIG process, the introduction of the bypass arc lead to a temperature decrease at the bottom of the hybrid arc due to energy redistribution. Furthermore, through the kinetic analysis, it was found that not only could the level of arc pressure be reduced, but also the action range of the arc pressure could be regulated up to 4.6 mm. The thermal force regulation mechanism worked together to enhance the stability of the molten pool and achieves good joint strength during the BCO-DASW of 6061 aluminum alloy. This research not only has great significance in further improving the welding quality and efficiency of aluminum alloy, but also deeper understanding of the energy regulation mechanism during aluminum alloy welding.

Experimental study on fatigue performance of double welded orthotropic steel bridge deck

Fatigue cracks which develop at multiple locations of orthotropic steel bridge decks (OSD) seriously deteriorate the safety and durability of steel bridges. U-rib fabricated using the double-sided penetration welding technique have been practically applied in bridges, but the fatigue performance of this type of U-rib has not been systematically studied. This study conducts fatigue tests on large-scale models of various fatigue details in the diaphragm area of orthotropic steel bridge decks with double-sided welds, obtaining the fatigue vulnerable locations and dominant cracking modes in the diaphragm area. The evolution law of out-of-plane deformation of diaphragm is clarified. The distribution characteristics of residual stress at the arched opening region and fatigue failure modes are acquired. Experimental results show that the interior weld toe of the U-rib-to-top-plate joint is the most fatigue-vulnerable zone, with a fatigue strength of 53.6 MPa. New fatigue cracks initiated from the weld toe of the top plate of the inner side of the U-rib or the weld toe of the U-rib perpendicularly or obliquely intersecting the longitudinal weld along 45° were found. After 10 million loading cycles, the residual stress in the arc-shaped opening area of the diaphragm reached 90–145 MPa, and the residual stress was higher where curvature of the opening was larger. The arc-shaped incision was in a circling state of tension and compression. It was also found that fatigue cracks that initiated from the weld toe of the diaphragm extended along the weld toe for some length before propagating into the diaphragm.

Investigation of angular deformation control for T-joint rib using multi-point constraint method

The circular rib is a crucial component of large pressure vessels, and its cross-section is primarily a T-joint structure. The double-sided arc welding (DSAW) process is an advanced technology for T-joint connection. However, during the T-joint welding process, harmful deformation still occurs in the form of angular deformation, including web and flange angular deformation. This paper proposes an innovative multi-point array constraint method to control the angular deformation of the rib based on the DSAW process for circular ribs. The welding deformation of the T-joint rib under multi-point constraints is studied using both numerical and experimental methods. The results of the numerical and experimental are consistent, with a relative error of no more than 12%. The multi-point constraint method is found to control angular deformation effectively, with the maximum angular deformation of the web not exceeding 1.77 mm and that of the flange not exceeding 0.45 mm after welding and releasing the constraint. The deformation control is significantly better than that of the rigid jig. Moreover, the coupling deformation of the web and flange caused by double-sided heat source and multi-point constraint forms an overall bending deformation. The deformation trend of each welding process is the same, with the main deformation occurring in the stage of releasing the constraint.

Achieving an improved performance in double-sided friction stir weld joints by adjusting the welding conditions during the passes of AA6061-T6 aluminium alloy

The present study aims at investigating the effect of interaction between the process parameters of each weld pass (1st pass and 2nd pass) to improve the joint performance during the double-sided friction stir welded joints of AA6061-T6 aluminium alloy. Experimental designs were conducted following a design matrix developed using response surface methodology to investigate the impact on the microstructural changes and tensile properties. Pronounced interaction between the process parameters of each weld pass of the joint was observed and indicated a strong interdependency between them. The detailed microstructural study conducted through EBSD insights into the extent of homogenization, and abnormal grain refinement and reflects a vast transformation of low-angle grain boundaries into high-angle grain boundaries within the stir zone. The profound examination through scanning electron microscopy and transmission electron microscopy analysis validated the uniform homogeneous distribution of Al-Fe and Al-Si-rich precipitates. The significant improvement in the grain refinement and distribution of the strengthening precipitates within the stir zone led to a substantial enhancement in the microhardness, along with achieving a maximum ultimate tensile strength of 223 MPa and a percentage elongation of 14%. A study of the fracture morphology ensures the ductile fracture behavior of the tensile fracture specimen by observing the presence of numerous dimples within a well-bonded joint.

Effect of laser oscillation and beam incident angle on porosity in double-sided filler welding of 2219 aluminum alloy T joint

In the current research, the double-sided laser beam oscillation filler welding (DLBOW) with beam incident angle from 20° to 40° were carried out for 2219 Al-Cu alloy T joint welding. Double-sided laser beam filler welding (DLBW) was conducted as a reference group. 3D computed tomography (CT) scanning analysis method was performed to investigate the precise three-dimensional locations of the porosity defects in the T joints. High-speed photography was conducted to evaluate the keyhole stability. The dynamic behavior of keyhole of DLBW and DLBOW was simulated by Flow-3D to study the formation process of pores. The effects of beam oscillation and beam incident angle on the macrostructure, microstructure, porosity, and mechanical property of T joints were discussed. It was found that beam oscillation and smaller beam incident angle promoted porosity suppression. The mechanical properties of T joints were improved by laser oscillation. With the beam incident angle of 20°, the porosity of T joint welded by DLBOW was lowest (0.26 %). The hoop tensile strength and T-pull tensile strength of the T joint were 403 MPa and 302 MPa, approximately 89.5 % and 71.6 %, in contrast with that of the base metal.

Microstructure, Mechanical Properties and Fatigue Crack Growth Behavior of Gas Tungsten Arc Welding Welded Joint of the Hastelloy N Alloy.

Hastelloy N alloy is an excellent oxidation and corrosion-resistant material, which is selected as the shell material for the main vessel of molten salt reactors (MSRs). In this work, we conducted double-sided gas tungsten arc welding (GTAW) on 4 mm thick Hastelloy N alloy plates to examine the microstructure and mechanical properties of the welded joints. The S-N curve was obtained by fatigue test. The experimental results show that fatigue cracks initiate along the weld toe and propagate inward in a fan-shaped pattern. The hardness is highest in the heat-affected zone (HAZ). The fracture mode observed was trans-granular. The plastic zone in the initial stages of crack propagation remained relatively minimal. However, it gradually expanded during subsequent stages of the process. It is noteworthy that the crack propagation process often involves the development of secondary cracks, accompanied by profound plasticity-induced closure effects. The results of our investigation demonstrate that the welded joint exhibits excellent fatigue performance.

Fatigue Performance of Rib-to-Deck Double-Sided Weld Joint of Orthotropic Steel Deck on Plate Girder Railway Bridges

This research work presents the stress behavior of rib-deck weld joints in Orthotropic Steel Deck (OSD) railway bridges. It is essential to determine the most vulnerable load mode of the wheels for fatigue failure of OSD bridges and to improve the fatigue resistance of the welded rib-deck connection. Fatigue performance largely depends on the weld stress. Double-sided welds for rib-deck welds improve fatigue performance. The fatigue behavior of the rib-deck double-sided weld joint has been compared with the single-sided one. This study used Abaqus software to create the global shell model and the solid submodel of the OSD. The results of the structural stress-based finite element analysis indicated that when the center line of the front axle pair of a locomotive coincides with the center line of the midspan of the bridge, the most severe loading condition occurs. The rib near the main girder experiences the maximum structural stress in the weld toe of the rib-deck joint. Moreover, the rib-deck double-sided weld joints have 43.7% less structural stress compared to single-sided weld joints at the root of the weld, and this improves the performance during fatigue of OSDs.

Improving joint performance of friction stir welded AZ31/ AM60 dissimilar Mg alloys by double-sided welding

Two types of welding processes，with double-side friction stir welding (DS-FSW) and single-side friction stir welding (SS-FSW)，were used for dissimilar welding between AM60 and AZ31 Mg alloys in this study. The evolution of texture and microstructure, deformation behavior and mechanical properties of both joints were investigated. The microstructure observation indicated that the microstructure of the joint nugget zone (NZ) under both processes was refined after welding and their grain size was relatively close. The two joints exhibited approximately symmetrical local strong texture distribution characteristics from the advancing side to the retreating side. However, the DS-FSW joint had a larger processing volume and a symmetrical macroscopic weld structure. Due to the symmetry distribution characteristics of texture in NZ, the Schmidt factors for basal slip of the joints from the vicinity of the NZ side to the NZ center showed a decreasing trend, resulting in severe strain localization in both DS-FSW and SS-FSW joints during the tensile process. The tensile tests revealed that the DS-FSW joint exhibited excellent mechanical.properties compared with the SS-FSW joint. This was attributed to its large processing volume, lower volume proportion of the stirring zone and symmetrically distributed weld zone structure improved the deformation coordination of the joint, thereby delaying its premature fracture and exhibiting better mechanical properties.