Double-circuit Line Research Articles

A hybrid intelligent system for protection of transmission lines connected to PV farms based on linear trends

Conventional relays face challenges for transmission lines connected to inverter-based resources (IBRs). In this article, a single-ended intelligent protection of the transmission line in the zone between the grid and the PV farm is suggested. The method employs a fuzzy logic and random forest (RF)-based hybrid system to detect faults based on combined linear trend attributes of the 3-phase currents. The fault location is determined and the faulty phase is detected. RF feature selection is used to obtain the optimal linear trend feature. The performance of the methodology is examined for abnormal events such as faults, capacitor and load-switching operations simulated in PSCAD/EMTDC on IEEE 9-bus system obtained by varying various fault and switching parameters. Additionally, when validating the suggested strategy, consideration is given to the effects of conditions such as the presence of double circuit lines, PV capacity, sampling rate, data window length, noise, high impedance faults, CT saturation, compensation devices, evolving and cross-country faults, and far-end and near-end faults. The findings indicate that the suggested strategy can be used to deal with a variety of system configurations and situations while still safeguarding such complex power transmission networks.

Analysis of hybrid AC/DC transmission system: A Turkey case study

AbstractThe need to transmit energy in the most effective way arises in parallel with the demand for energy in developing countries. As the amount of transmitted power increases, transmission lines can become overloaded, causing a blackout. This study aims to increase the transmission capacity without experiencing right‐of‐way problems by converting Turkey's existing high voltage AC systems to hybrid AC/DC systems. With such a design, it is aimed at providing more efficient and continuous transmission by using the high‐voltage DC system's low‐loss feature at long distances. Using the 400 kV double circuit line structure, the existing electricity transmission system is modelled using real data in the DigSILENT PowerFactory. The electromagnetic fields that will occur due to the use of AC and DC circuits on the same tower in such a transformation situation are analysed with FEMM 4.2, based on the finite element method. The compliance of the electromagnetic fields that will occur with the use of hybrid 400 kV AC and 500 kV DC was determined in the study. In addition, according to the simulation results, it is predicted that in the case of hybrid AC/DC transmission, the current transmission capacity would increase and the losses would decrease.

Evaluation of the backflashover performance of 150 kV and 400 kV double-circuit overhead transmission lines as affected by lightning attachment models and peak current distributions

The evaluation of the backflashover performance of overhead transmission lines requires the adoption of a lightning attachment model and a peak current distribution. These affect the estimated backflashover rate, BFR, of the lines. The present study aims to quantify the influence of lightning attachment model and peak current distribution on the BFR of double-circuit overhead lines. This is achieved by evaluating typical 150 kV and 400 kV lines. ATP-EMTP simulations are conducted to obtain the critical currents causing backflashover of line insulation. Then, the critical currents are used in lightning incidence computations to obtain BFR. The influencing parameters taken into account in this work are the low current and low frequency tower ground resistance, the location of lightning strike to the shield wire along the span, and the AC voltage phase angle, all affecting the critical backflashover current. Several lightning attachment models and peak current distributions are evaluated. Their influence on BFR is found to be considerable, especially for lower tower ground resistance values. The lightning peak current distributions yield more pronounced effects on BFR. The results of this study stress the need for computing BFR using a more accurate expression than the simplified one based on CIGRE TB 63.

Single-circuit equivalent of a double-circuit line with parallel operation of circuits

Single-circuit equivalent of a double-circuit line with parallel operation of circuits

Detection and Correction of PMU Angle Deviation for Double-Circuit Line Using Reactive Power Measurements

Detection and Correction of PMU Angle Deviation for Double-Circuit Line Using Reactive Power Measurements

Compensation of Ground Distance Protection of Double-Circuit Lines for Under-/Over-reach Caused by High-Resistance/Irrelevant-Circuit Faults

Compensation of Ground Distance Protection of Double-Circuit Lines for Under-/Over-reach Caused by High-Resistance/Irrelevant-Circuit Faults

Coupling characteristics between MMC-HVDC and AC transmission lines on the same tower and their impact on protective relaying

Significant coupling exists between DC and AC lines erected on the same tower or sharing transmission corridors. Electromagnetic and electrostatic coupling between DC and AC lines are investigated based on ± 500 kV MMC-HVDC and 500 kV double-circuit AC lines on the same tower. The interactive coupling characteristics and their impacts on protective relaying are analyzed during normal operation and after DC or AC faults. Voltage coupling ratio and current coupling ratio are defined. The 50 Hz components in MMC-HVDC line may be higher than ripple criterion under the coupling of AC line and can be even more significant when a fault occurs on adjacent AC line. The DC reactor with larger inductance can reduce its impact on MMC-HVDC system. Zero-sequence overcurrent relaying and zero-sequence directional relaying for AC lines may mal-operate when a fault occurs on adjacent MMC-HVDC line. And there is also an interruption risk for AC systems. Improvement schemes are proposed to avoid the mal-operation of protective relaying. Simulation case studies verify the correctness of coupling characteristic analysis and the effectiveness of proposed improvement scheme.

Hybrid Active and Passive Cable Contour Shielding of Magnetic Fields of Double-Circuit Overhead Power Lines

The purpose of the work is to design a hybrid screen designed to reduce the level of the magnetic field generated by double-circuit overhead power lines, to increase the efficiency of shielding the original magnetic field in residential buildings, to the level of sanitary standards and to reduce the sensitivity of the system to changes in system parameters. To achieve this goal, the structure of a hybrid screen was determined, consisting of a double contour active and a cable contour passive part. The developed hybrid screen is characterized by increased efficiency in reducing the magnetic field of industrial frequency. Designing a hybrid screen comes down to solving a minimax vector optimization problem, in which the vector objective function is calculated based on solution to Maxwell's equations in a quasi-stationary approximation using the COMSOL Multiphysics software package. The solution to the minimax vector optimization problem is calculated based on multi-particle swarm optimization algorithms from Pareto-optimal solutions taking into account binary preference relations. During the design of the hybrid screen, the coordinates of the spatial location of the two compensation windings, as well as the magnitude of the currents and its phases in the windings of the active screen, were calculated. The important results are theoretical and experimental studies on the effectiveness of the designed hybrid magnetic field shield generated by double-circuit overhead power lines. The significance of the results obtained lies in the fact that practical recommendations are given for a reasonable choice of the spatial arrangement of two shielding windings of a robust system of hybrid shielding of the magnetic field generated by double-circuit overhead power lines.

Analysis of Increased Induced Voltages on the Sheath of Double-Circuit Underground Transmission Lines Guaranteeing Ampacity

This paper quantifies and discusses the increase in induced voltage on a sheath due to changes in duct banks in terms of type and dimensions along an underground transmission line, guaranteeing the ampacity required for a project. The four most common duct banks in double-circuit underground transmission lines with phase transposition were considered in this study, along with two special cross-bonding techniques: continuous cross-bonding (CCB) and sectionalized cross-bonding (SCB). These techniques aim to reduce sheath currents and enhance the distribution of the induced voltage on the sheath. The analysis considers two distinct scenarios in which the profile of the induced voltage is calculated: the first one accounts for underground obstructions, intersections with important traffic avenues, and ground with high excavation costs that force changes in the duct bank dimensions and configuration, which is the most exact and realistic case. The second one solely considers one typical configuration of a duct bank along the route. This last scenario is normally applied to calculate the induced voltage when an underground transmission design is required. The results show that when installing cables at a greater depth, it is imperative to increase the distance between them to guarantee the ampacity. The induced voltage on the sheath will rise as the distance increases. Furthermore, the results reveal that instead of calculating the induced voltage by considering the scenario that is exact and most like a real case, it is enough to calculate following the second scenario and then add a scaling factor according to each duct bank configuration.

Estimation of lightning overvoltages and critical flashover currents of 150 kV and 400 kV overhead lines: Effects of the CIGRE lightning current waveform parameters

This paper investigates the influence of the CIGRE lightning current waveform parameters on the computation of fast-front overvoltages and critical lightning currents causing flashover of overhead transmission line insulation. The investigation is conducted via ATP-EMTP simulations employing both negative and positive lightning current waveforms corresponding to first return strokes. Typical 150 kV and 400 kV double-circuit overhead lines are evaluated by performing shielding failure and backflashover simulations. The statistical distributions of the parameters required as input for the CIGRE lightning current waveform (front time, maximum steepness, time to half value) are considered in simulations to quantify and analyze their effects; this enables the comparison between negative and positive lightning strikes. The waveform parameters do not affect considerably the critical shielding failure flashover current for both polarities; the most influential parameter in this case is the time to half value. On the other hand, the wavetail duration influences the least the critical backflashover current; the latter is lower for waveforms with faster wavefront (lower front time and higher maximum steepness). The impact of the waveform parameters of positive lightning strikes is more marked for the backflashover case due to their larger variations compared with negative strikes.

An Adaptive Reclosing Scheme for Cross-Line Faults on Double-Circuit Wind Power Outgoing Lines with Shunt Reactors

Wind turbines are vulnerable to negative sequence current injection, the conventional automatic reclosing scheme for wind power outgoing lines, since we may inject negative sequence components into the system and reclose it without distinguishing the nature of the fault through rectification. Moreover, reclosing in permanent faults could induce a secondary impact on the system. To solve the above problems, an adaptive reclosing scheme for cross-line faults on double-circuit wind power outgoing lines with shunt reactors is proposed. Firstly, a new tripping strategy and a single-side partial-phase reclosing method are proposed for multiple types of outgoing line faults, while, simultaneously, phase-to-phase coupling loops are established. Secondly, the criteria of fault nature are established based on the fault phase shunt reactor current and fault phase voltage characteristics, and transient faults are rapidly and accurately distinguished from permanent ones according to the criteria. Finally, the theoretical derivation and simulation experiments are conducted on the PSCAD/EMTDC platform to demonstrate that the proposed adaptive reclosing method is applicable to avoid the injection of negative sequence currents into wind turbines. Meanwhile, the success rate of reclosing for wind power outgoing line is significantly improved and the continuity of power transmission on the wind farm(s) is ensured.

Assessment of photovoltaic generation penetration effect on the maximum loadability of the system

This paper proposed a method to investigate the effect of increasing PV penetration on the voltage stability of an IEEE 14-bus test system considering maximum PV penetration and system loadability limit. The critical bus of the test system has been decided based on nose curve analysis. The solar PV system is deployed with the most critical bus of the system. The effect of increasing PV penetration on the improvement in the loading capacity of various power system components like transmission lines, transmission line transformers, and generators is investigated over the adopted test system. Based on solar PV penetration up to 100 MW, the maximum loadability limit of the IEEE 14-bus test system increases, as shown by the results. Bus 14 is found to be the most severe bus of the test system using the continuation power flow (CPF) method. However, in some cases, overloading situations develop after a certain limit of PV penetration in the power system. In this condition, the overloading of the power system equipment is improved by the use of a Static Synchronous Compensator (STATCOM) at bus number 14, a double circuit line in the critical line (9–14), and Static Synchronous Series Compensator (SSSC) in the most severe line (9–14) in the system. The maximum loadability of the system gets maximum enhanced from 4.0349 p.u. to 4.5602 p.u. under simultaneous use of solar PV generation, SSSC, and STATCOM at the most critical bus and in most severe line of the system. As evidence, the enhancement in maximum loadability of the system found using the proposed method has been also compared with the existing research. The maximum system loadability has been also enhanced under normal and (N-1) contingency conditions by the use of PV penetration in the system. PSAT/MATLAB software is used for simulation and maximum loadability has been investigated by continuation power flow (CPF) method.

Ferroresonance phenomena in power systems

It is a known fact that the world's dependence on electrical energy is increasing day by day. The fact that electrical energy has some advantages over other types of energy, the increasing world population and changing living conditions can be considered among the reasons for this increase. This increase in dependence on electrical energy can be met by expanding existing facilities and establishing new facilities. In these studies, the transmission of electrical energy from the place where it is produced to the place where it is consumed poses important problems as the system expands. Some work is required to eliminate these technical and economic problems and to ensure stable operation of the system. These are problems that were not considered beforehand as the system grew. One of these problems is the ferroresonance phenomenon that occurs at the fundamental frequency due to the nonlinear magnetization characteristics of transformers. Ferroresonance is a resonance phenomenon that occurs in an electrical circuit containing an iron-core self-coil as a nonlinear element. This resonance manifests itself with sudden oscillations in the output size of the system caused by a small change in the amplitude or frequency of a magnitude applied to the input of the system. High voltage transmission lines are double-circuit lines that share the same pole. In special cases such as maintenance or malfunction of such a transmission system, one of the lines can be disconnected from the system and continue energy transmission with the other line. In the high voltage transmission line, the system may oscillate due to the stored energy in the magnetic field of the transformer inductance on the disabled line and the electric field of the line capacity. This oscillation disappears after a certain period of time due to iron losses and other circuit losses. When these losses are covered by the other transmission line, permanent oscillations and over voltages may occur at the transformer terminals. All these events are the negative effects of ferroresonance on transmission systems. In the energy transmission system, ferroresonance phenomenon occurs. Over voltages may occur in case of idle power transformers in star point/isolated networks. In medium voltage networks, ferroresonance occurs due to the melting of a fuse, the opening and closing of voltage transformers with one pole, and the dissymmetry that occurs as a result of a connection process. These negative effects caused by ferroresonance in the energy transmission power system are discussed in detail within the subject of this study.

The Calculation Method of the Floating Conductor Potential in the Ion Flow Field

For bipolar DC transmission projects, when one pole conductor is charged and running normally, and the other pole conductor is in a standby state (including cold standby and hot standby), if the standby pole conductor is not grounded, a high charging potential will appear on the surface. On the one hand, it will affect the insulation coordination and protection setting of the DC system. On the other hand, it will also affect the ion current and synthetic electric field on the ground. This article studies the calculation method of the potential of suspended conductors in the presence of floating conductors in the ion flow field, establishes a calculation model based on the minimum absolute value of the space charge density on the surface of the conductor, and calculates and analyzes the distribution of ionizing current and synthetic electric field below the ground of high-voltage DC lines in the presence of suspended conductors. The distribution laws of ground field strength and ion current in single-circuit bipolar DC transmission lines are studied when one pole is suspended, the other is operated, and when one circuit is operated. One circuit is shut down in double-circuit DC transmission lines on the same tower. For practical engineering, on the one hand, it is possible to predict the potential of suspended conductors in the ion flow field and propose adjustment plans for protection settings, insulation coordination, etc., in advance. On the other hand, when considering abnormal operating conditions, the impact of ion flow fields on the ground electromagnetic environment can be reduced by changing the geometric architecture and line selection.

A new method for fault location in special parallel lines called “stitched lines”

Today, a special kind of parallel double-circuit line, designated "stitched lines," is employed in various transmission and sub-distribution networks in some countries, like Iran. In this type of unusual line, two circuits are connected at the beginning and end of the route and enter the high-voltage substations by a single line. Since on these lines there is no access to the current of each circuit separately, their protection, especially fault location, has faced a major challenge. Therefore, this article establishes a new method based on symmetrical components (positive sequence) to determine the location of the faults in the stitched lines. To scrutinize the performance of the proposed approach, comprehensive simulations have been run in the PSCAD/EMTDC software under a variety of different situations. The suggested method's accuracy has been established for a variety of fault locations and resistances. It has also been determined how the suggested approach performs when subjected to noise, current transformer saturation, arcing faults, transposition type, source impedance variation, and load changes. The obtained results show that the proposed approach is accurate under different scenarios, making it an excellent choice for practical applications.

Electromagnetic Shielding of Two-Circuit Overhead Power Lines Magnetic Field

The purpose of the work is to design an electromagnetic shield to reduce the level of the magnetic field generated by double-circuit overhead power lines to increase the shielding efficiency of the initial magnetic field in residential buildings to the level of sanitary standards and reduce the sys-tem's sensitivity to changes in system parameters. To achieve this goal, the structure of the electro-magnetic shield is determined, which consists of a single-circuit active and multi-circuit passive parts and is characterized by an increased efficiency of reducing the magnetic field of industrial frequency. The design of an electromagnetic shield is reduced to solving a minimax vector optimization problem, in which the vector objective function is calculated based on solutions of Maxwell's equations in a quasi-stationary approximation using the COMSOL Multiphysics software package. The solution of the minimax vector optimization problem is calculated on the basis of optimization algorithms by a multiswarm of particles from Pareto-optimal solutions. The most important results are theoretical and experimental studies of the effectiveness of the designed electromagnetic shield of the magnetic field generated by double-circuit overhead power lines. The significance of the results obtained lies in the fact that practical recommendations are given on the reasonable choice of the spatial arrangement of the contours of the multi-circuit passive screen and the shielding winding of the robust system of elec-tromagnetic shielding of the magnetic field generated by double-circuit overhead power lines. The possibility of reducing the induction of the initial magnetic field to the level of sanitary standards has been shown as well.

Reed switch protection of double-circuit lines without current and voltage transformers

Protection of 6–35 kV double‐circuit lines from the supply side is suggested. It allows saving copper, steel, and high-voltage insulation in amounts unprecedented for relay protections. The protection is based on the control of sequence of actuation of reed switches fastened near the corresponding phases at a safe distance and of the time Δt between their actuation. The effect of all possible errors on Δt is studied and the number of reed switches required to be mounted near the phases of the lines is determined. The peculiarities of selection of Δt and inductions for the protection operation, points of reed switch mounting, sensitivity estimates, and the fields of use of the protection are analyzed. An example of the selection is considered. The protection operation algorithm is formulated and written in the form of switching algebra functions with allowance for the protection operability in the case of reed switch failures. The correct operation of the protection is shown in all actual modes of operation of the lines (including the failure of one of reed switches). A construction for fastening reed switches at a safe distance from the line phases is presented.

A protocol for selecting viable transmission line arrester for optimal lightning protection

Direct lightning strikes on overhead lines and towers causes power system outages. Optimal surge arrester placement is a practical and economical protection technique. From research trends, three types of transmission line arresters are in practice: Non-Gapped Line Arrester (NGLA), Externally Gapped Line Arrester (EGLA) and Multi Chamber Insulator Arrester (MCIA). This study proposed a simplified guide for selecting the most suitable line arrester considering the placement configurations, double circuit outage prevention and energy capabilities. Electromagnetic Transient Program was implemented to analyze back flashover performance of a typical 275 kV double circuit transmission line in Malaysia. Critical flashover parameters considered are lightning current magnitude, tower footing resistance, and power frequency angle. Analyzed results from the three arresters found that installing four arresters, two per circuit, at the lower and upper phases respectively, is the most optimal and universal double outage mitigation technique. Energy comparison reveals that MCIA discharges 54% and 44% less energy than NGLA and EGLA respectively. Also, from 132 kV system results, MCIA discharges 74% and 22% lesser energy respectively. From further validation of the simulation model, NGLA discharged 23.8% more energy than EGLA from experimental results. The proposed guide is applicable to double circuit lines below 275 kV.

Distributed Parameter Based Setting-Free Fault Locator for Double-Circuit Line Using Fault Data

Distributed Parameter Based Setting-Free Fault Locator for Double-Circuit Line Using Fault Data

Unsynchronized Parameter-Free Fault Location for Two or Three Terminal Double-Circuit Transmission Lines Sharing the Same Tower via Unscented Kalman Filter

This paper proposes a novel phasor domain fault location method for two or three terminal double-circuit transmission lines sharing the same tower without requiring line parameters. First, the models of the two and three terminal double-circuit lines with faults are derived. The line models fully consider the mutual coupling between the two line circuits, distributed line parameters, asymmetry of line structures, and extensive fault types. Through the modeling procedure, the fault location, line parameters, unsynchronized phase angle, fault resistance and other internal states of the line are introduced as unknown variables, resulting in a highly nonlinear problem. Afterwards, the line model is solved via the state estimation algorithm. Compared to the existing least square type algorithms such as Gauss-Newton and Levenberg Marquardt methods, the proposed Unscented Kalman Filter based algorithm greatly improves the convergence region. Compared to the existing parameter-free fault location method on double-circuit transmission lines, the proposed method more accurately presents the physical laws of the line and is compatible with common or split bus configurations. The proposed method is verified via numerous simulation experiments, proving that it can accurately locate faults for different fault resistances, locations and types. The method is also validated via field data experiments.