Ash Disposal Research Articles

Experimental analysis of concrete with partial cement replacement using incinerated hospital waste ash

The annual production of medical waste from healthcare facilities in Pakistan is around 250,000 tons. An effective waste management system is essential for disposing of hazardous medical waste, and incineration is considered the most effective and accessible technology. Disposal of medical waste ash in landfills without proper treatment could lead to groundwater contamination due to leachate. This research paper aims to evaluate the feasibility of using hospital waste ash obtained from the National Cleaner Production Center (NCPC) in Rawalpindi as a partial replacement for cement. The primary variable in this study was the amount of hospital waste ash (0%, 3%, 7%, and 10% by weight of cement), while the amount of cementitious material, water-to-cement ratio, and fine and coarse aggregate content were kept constant. A total of 36 cubes were cast, with nine cubes for each replacement level for curing periods of 7, 14, and 28 days. The slump value and density of fresh concrete decreased with the increase in the proportion of hospital waste ash in the mix. The compressive strength of mixes with 3% hospital waste ash was higher than that of the control mix. The best results (20.13 MPa) were obtained from the 3% mix after 28 days of curing, while the result obtained with the 7% mix was nearly equal to that of the control mix.

A STATE OF ART AND PROSPECTS OF FLY ASH MANAGEMENT

The basic data on the volume of formation and composition of fly ash, which is a product of coal combustion at thermal power stations, are given. The analysis of the current state of ways of managing fly ash makes it possible to distinguish the following main directions: physical-mechanical, physical-chemical, biological and combined methods of handling it, which are used in agriculture (use as fertilizers and pesticides; chemical land reclamation: regulation of the structure and pH of the soil); during earthworks (reinforcement of weak and expansive soils, use as tamponage compositions, arrangement of embankments and dams); road construction (strengthening of the soil for the lower layers of the road surface; production of asphalt, cement-concrete mixtures for arranging the foundations of road clothing, as well as crushed stone-sand and gravel-sand mixtures reinforced with cement); building materials industry (cement, concrete, building solutions, geopolymers, bricks, building blocks, glass, glass ceramics, building ceramics, porous ceramics, rolled waterproofing materials); in protective coatings (paints, enamels, enamel glass, shotcrete, heat-protective and heat-insulating coatings); as sorbents and catalysts and their carriers; in mechanical engineering (abrasive, frictional, filtering and lubricating materials, materials for soldering, foundry sand forms or rods); as other materials (pigments, polymer composites, elements of chemical sources of electric current, accumulators of certain substances, carbon nanoparticles (fullerenes, nanotubes), cosmetics and hygiene products); in pyrometallurgical and hydrometallurgical methods of recovery of chemical elements; in alloys and metal matrix composites; for extracting rare earth elements. Currently, the most appropriate methods of disposal of fly ash are either its direct use with a minimal change in its properties, or its use with minimal processing and minimization of the formation of new waste, in particular in the building materials industry and road construction. Bibl. 164, Fig. 3.

Health and Environmental Risk Assessment of Heavy Metals Contamination from Medical Wastes Ash of Baghdad Hospitals

Abstract One of the complex problems that many countries suffer from is how to deal with medical waste because of its harmful and devastating effects on humans and the environment. Hospitals around the world use and consume many different products. These products are composed of various materials, and many of them contain heavy metals in their production and manufacturing, which are ultimately emitted into the environment, posing a major danger and risk to human health. This work focused on assessing the contamination levels of medical waste ash after the incineration process. Ash samples were collected from major hospitals in the capital, Baghdad. The health risks resulting from heavy metal pollution were calculated. Medical waste ash was collected at different times from three major hospitals within the capital, Baghdad, and tested for contamination with heavy metals. To measure the bottom ash samples, X-ray spectroscopy (XRF) technology was used to determine heavy metal concentrations. The results showed the presence of more than twenty elements in the ash of medical waste, including the heavy metals found in Baghdad hospitals. Work was done on eight of these heavy metals due to their high concentrations. These selected elements are considered highly toxic and dangerous if exposed to them, including zinc (Zn), lead (Pb), arsenic (As), cobalt (Co), and copper. (Cu), nickel (Ni), chromium (Cr), and mercury (Hg). To evaluate the health risks of this pollution. All of these elements are a major problem if exposed to them. The amount of contamination was calculated using the contamination factor (CF). The results showed that the percentage of As, Cd, Hg, Zn, Pb, and Cu was very high. Meanwhile, the concentrations of Co and Ni were moderate values in medical waste ash. Adult health risks were calculated using the non-cancer health risk ratio (HL). The calculated values show values higher than the safe level in Imam Ali Central Hospital, indicating a potential high health risk. Meanwhile, other hospitals (Sheikh Zayed and Dhari Al Fayyad) recorded risk values below the safe level, indicating no health risks. The health risk assessment indicated that there are three main routes of human exposure: “ingestion, inhalation, and skin contact.” The cancer risk index (Risk) was also calculated. The values obtained were within the acceptable range. An analysis of the metal pollution index was also conducted, and it was found that heavy metals pose a non-cancerous risk. But the harmful effects of pollution from ash disposal have been particularly serious because they may contain high concentrations of heavy metals.

Impacts of alkaline washing pretreatment on municipal solid waste incineration fly ash (MSWI FA) and resulting geopolymers

The safe disposal and utilization of municipal solid waste incineration fly ash (MSWI FA) has emerged as a crucial challenge, primarily due to elevated levels of heavy metals and chlorides. In this study, the influence of key factors in different pretreatment methods on the physicochemical properties of MSWI FA was analyzed, and the effects and mechanism of different pretreatment methods on the resulting geopolymers were studied. Under the conditions of a liquid-solid ratio (L/S) of 7 mL/g, a rotational speed of 500 r/min, and a stirring time of 20 min, the alkali washing with 1 mol/L NaOH solution exhibited better effect than water washing. The total content of chlorides and the content of soluble chloride in AFA (MSWI FA with alkali washing) were 1.53 % and 0.85 %, respectively. Alkali washing had a greater influence on the migration of heavy metals from MSWI FA to filtrate than water washing. Meanwhile, alkaline washing exhibited better effect in calcium retention and sulfur removal. The pretreatment process enhanced the gel formation in geopolymers, subsequently exerting a significant influence on the compressive strength and leaching concentration of heavy metals. Thermogravimetric analysis showed the bound water content in AG (8.46 %) was the greatest in all simples, indicating that exerted the most pronounced impact on the gel formation during geopolymerization. And, the lower ratio of Si-O-Na to Si-O-T in AG (0.20) indicated a longer geopolymeric chains, which explained the higher compressive strength of geopolymers during the initial curing period. This article provides a new pretreatment method to promote the resource utilization of MSWI FA.

Pioneering study of radioactivity in soil near the Payra 1320 MW Thermal Power Plant, the largest coal-fired thermal power plant in Bangladesh

ABSTRACT Coal combustion increases atmospheric radioactivity, harming those live in the periphery of coal-fired thermal power plants (CFTPPs). A pioneering study has been performed using a high-purity germanium detector by analysing 30 soil samples collected from distances of 50, 600, 1200, and 3000 metres in the periphery of the largest 1320 MW CFTPP, Payra, Bangladesh. The activity concentrations of 226Ra, 232Th and 40K ranged from 19–32, 31–90, and 420–870 Bq/kg, respectively, with most of the samples show 232Th and 40K levels above global averages. Elevated levels of 232Th and 40K in soil around Payra thermal power plant stem from natural minerals, granitic rocks, ash disposal, coal combustion residues, and environmental factors. Radiological hazard indices, including dose rates and cancer risk, exceed global averages, indicating unsafe radiation exposure for coal miners and locals. These findings are crucial for planning coal-fired power plants and stress the need for municipal regulation of fly ash and health monitoring to mitigate risks for workers and residents.

The Potential of Helichsryum splendidum (Thunb.) Less. for the Restoration of Sites Polluted with Coal Fly Ash.

The disposal of coal fly ash (CFA) generated from coal-fired power stations has serious impact on the ecosystem, by converting large pieces of land to barren ash dams with the potential to contaminate groundwater, surface water, air and soil. The aim of this study was to clarify the potential of phytoremediation using Helichrysum splendidum (Thunb.) Less. in areas polluted by CFA through conduction of pot trial experiments for 14 weeks. Plants of the same age were cultivated in CFA to assess their growth, photosynthetic rate and tolerance towards metal toxicity. This study revealed that the CFA was moderately polluted with heavy metals, and a lower photosynthetic rate was recorded for the CFA plants in comparison to the controls (plants grown in soil). Although the CO2 assimilation rate was lower for the CFA plants, increased growth was recorded for all the plants tested. Inductively coupled plasma mass spectrometry (ICP-MS) was used to quantify the amount of trace elements in samples and parameters including translocation factor (TF) and bioconcentration factor (BCF) were used to evaluate the phytoremediation potential of H. splendidum (Thunb.) Less. The results revealed that higher concentrations of Cd, Co, Cr, Cu, Mn and Pb were accumulated in the roots, while As, Ni and Zn were found in the shoots. Elements including As, Cr and Zn reported TF values above 1, indicating the plants' phytoextraction potential. The BCF values for As, Cu and Zn were 1.22, 1.19 and 1.03, indicating effectiveness in the phytostabilization processes. A removal rate efficiency ranging from 18.0 to 56.7% was recorded confirming that, H. splendidum (Thunb.) Less. can be employed for restoration of CFA dams.

Nilai Moderasi Beragama Pada Tradisi Upacara Kremasi Jenazah Di Desa Rama Agung

The aim of this service is to strengthen the attitude of religious moderation by understanding and practicing the value of moderation in Rama Agung Village. It is hoped that this can make a positive contribution to the development of attitudes of tolerance and harmony in society. This research describes a series of procedures from the beginning to the end of cremation in Lama Agung village. Apart from that, this research also examines how the value of religious moderation is applied in a very harmonious and mutually supportive society. This research aims to provide a deeper understanding of the application of facilitation in the context of community diversity and harmony in the village by explaining the details of the cremation process and social interactions that occurred while I was here. The qualitative approach of this research is to collect primary data through interviews with Hindu traditional leaders who are directly involved in the implementation of the Ngaben ceremony. This method helps us to understand more comprehensively the aspects of ritual and religious facilitation in Rama Agung village. The results of this research show that the cremation death ritual includes several stages, namely preparation of offerings and equipment, handover of the body, implementation of the cremation ceremony, and reading of praise songs. Collection and disposal of ashes, closing of the event and evening prayer at Mentebengan.

Synthesis and Characterization of Silicon Nanoparticles from Coal Fly Ash Using Ultrasonication as a Battery Anode

Fly ash, a byproduct of coal combustion, is rich in silica, alumina, and other minerals, making it a valuable resource for extracting high-purity silicon. The synthesis of silicon nanoparticles from coal fly ash involves several critical steps, including the extraction of silica (SiO2) via the sol-gel method, reduction of silica to silicon using the metallothermic method, and subsequent ultrasonication to achieve nanoscale particles. Studies have shown that fly ash can contain up to 49.21% silica, which can be further purified to 93.52% via chemical extraction methods such as acid leaching and alkali dissolution. The reduction of silica to silicon is carried out using the metallothermic method, which involves the use of magnesium-reducing agents to convert SiO2 to elemental silicon. This process produces silicon with a purity of about 61.3%, which can be further increased through ultrasonication. Ultrasonication is a technique that uses high-frequency sound waves to break particles into smaller sizes, resulting in more uniform and homogeneous nanoparticles. In this study, ultrasonication for 60 and 120 min reduced the average particle size of silicon from 208.94 nm to 58.87 nm and 20.13 nm, respectively, and increased the silicon content to 74.6% and 72.7%. X-ray diffraction (XRD) and distribution particle analyses confirmed the particle size reduction and homogeneity of silicon nanoparticles, indicating the effectiveness of ultrasonication in producing high-quality silicon nanoparticles. The synthesized silicon nanoparticles have significant potential applications, particularly as anode materials in lithium-ion batteries, due to their increased surface area and improved electrochemical properties. Furthermore, the use of fly ash as a raw material for the synthesis of silicon nanoparticles not only provides a cost-effective and environmentally friendly alternative to traditional silica sources but also helps in reducing the environmental impact of fly ash disposal. The integration of the methods and findings of this study underscores the feasibility and benefits of using coal fly ash for the sustainable production of silicon nanoparticles, which can be utilized in energy storage as anode materials in lithium-ion batteries.

Isolation and biochemical screening of Phosphate Solubilizing Bacteria from Kans grass rhizosphere of Fly Ash Dump Sites near NTPC, Angul

Soil bacteria, capable of converting insoluble phosphorus into soluble, plant-accessible forms, collectively known as phosphate-solubilizing bacteria (PSB), have emerged as an eco-friendly and cost-effective solution for supplying phosphorus to plants. This study presents preliminary insights into the rhizospheric bacterial population associated with the vigorously growing kans grass (Saccharum spontaneum L.) at different fly ash disposal sites of NTPC, Kaniha in Angul district, Odisha. In the quest for efficient plant growth promoting rhizobacteria (PGPR) strains with diverse beneficial activities, a total of sixteen bacterial isolates were collected from the rhizosphere of chosen plant species and identified, with only ten isolates underwent biochemical characterization. Among these, four isolates exhibiting a higher phosphate-solubilizing index were further characterized, serving as a foundation for future exploration of the bio-prospective potential of rhizosphere bacteria in this unique ecological niche. Further assessment of these isolates, showcasing several plant growth-promoting (PGP) traits, is essential to determine their efficacy as potent PGPR agents.

Environmental sustainability of closed-loop regeneration of NaHCO3 in CO2 utilization-driven desulfurization ash: From the perspective of integrated hybrid life cycle assessment

The closed-loop regeneration of NaHCO3 by treating sodium-based desulfurization ash (SDA) using CO2 in flue gas and ammonia by-products demonstrates an attractive perspective of low-cost sodium-based dry desulfurization (SDD) application. To push generation reuse of desulfurization ash into more practices, taking the application in coking plants as a case, this study first compares the environmental and economic performance of four scenarios of flue gas desulfurization (FGD) and desulfurization ash disposal by integrated hybrid life cycle assessment (IHLCA) with life cycle costing. Compared with process-based LCA, IHLCA captures more environmental impacts through the economic input-output (EIO) system, especially 36.40–67.89% of terrestrial ecotoxicity comes from the EIO system. Based on evaluation results of four scenarios, among the ten environmental impact categories (excluding photochemical oxidation), the SDD scenario with NaHCO3 regeneration by CO2 and ammonia (S2) is not only the most environmentally friendly route, but also has the lowest total hourly operating cost. These are mainly due to the offsetting effect of by-products replacing traditional chemicals on the total impact and avoiding landfill and raw material transportation. Furthermore, sensitivity analysis also shows that when technical parameters change, the environmental and economic performance of S2 still remains the best, except for the case when the NaHCO3 regeneration rate is 60%. The findings will be valuable for the selection and optimization of FGD in coking plants, incineration plants, and others.

Radioactivity of Technosols on thermal power station ash disposal sites: Assessment of potential radiological human‐health risk

AbstractSoil radioactivity is a poorly recognized form of land degradation; however, there are regions all around the world where it can be dangerous to the environment and human health. The aim of the study was to analyze the radioactivity of Technosols developed on thermal power station (TPS) ash disposal sites. Total concentration of uranium (U), thorium (Th), and cesium (Cs), as well as the radioactivity of select radionuclides in Technosols were determined to recognize the level of radioactivity and to assess the potential radiological health risk. Total U, Th and Cs concentrations in Technosols were in ranges 1.5 to 11.3, 4 to 22.9, and 0.2 to 21.3 mg·kg−1, respectively. The radioisotope activities in Technosols (in Bq·kg−1) were in the 1.6–25.5 (137Cs); 29.2–1265 (40K); 26.2–99.9 (228Th); 27.9–100 (228Ra); 20.5–134. (226Ra); 32.8–177 (210Pb); 23.9–144 (238U); 1.2–7.0 (235U) ranges. The activity concentrations were slightly higher than the activities of non‐contaminated soils. Technosols developed from bituminous coal ash had higher 40K, 228Th, and 228Ra activity concentrations than soils developed from lignite ash. Artificial 137Cs occurred in surface horizons of Technosols due to fall of atmospheric dust enriched in 137Cs. Annual effective dose (AED) in Technosols amounted 0.07–0.16 mSv·a−1 and was somewhat higher than the global and Polish average (0.06 and 0.07 mSv·a−1, respectively) for outdoor external terrestrial radiation. The radioactivity of the investigated Technosols is slightly above the average radioactivity of native soils. The radiological human‐health risk related to the analyzed soils is low.

The impacts of furnace and fuel types on the hazardous heavy metal contents and leaching behavior of woody biomass fly ash

In efforts to reduce net CO2 emissions, the use of woody biomass as a fuel for power generation has grown rapidly. However, this practice is expected to generate large amounts of combustion ash. To support the subsequent use and disposal of combustion ash, it is important to understand its hazardous heavy metal (HHM) contents and leaching behavior. Therefore, we investigated the impacts of furnace type and fuel on HHM contents and leaching behavior based on 60 types of woody biomass fly ash (WBFA). A safety assessment of WBFA as fertilizer based on HHM contents revealed that 20% of the WBFA samples exceeded the prescribed standards. Therefore, WBFA would require preprocessing before reuse as fertilizer. The leaching test results showed that 95% of the WBFA samples could be landfilled as industrial waste without special treatment. However, prior to reuse in construction materials or soil amendments, it would be necessary to remove or fix HHMs to prevent leaching. Overall, WBFA generated from the combustion of waste wood as fuel tended to have higher HHM contents and leachate concentrations than WBFA from other woody biomass-based fuel types.

Mix design of FA-GGBS based lightweight geopolymer concrete incorporating sintered fly ash aggregate as coarse aggregate

Geopolymer concrete (GPC) is emerging as a sustainable alternative to conventional Portland cement-based concrete due to its significantly reduced carbon footprint and enhanced durability. To mitigate the environmental hazard posed by the disposal of fly ash (FA) and ground granulated blast furnace slag (GGBS) waste and reduce cement consumption, effective promotion of the geopolymerization technique is necessary. Incorporating sintered fly ash coarse aggregate (SFA) in GPC makes the concrete light in weight. This study involves the synthesis of geopolymer technology using FA and GGBS, as the primary source material. Due to the lack of an appropriate mix design method for using SFA in GPC, their application as a structural concrete is scanty. By using FA and GGBS with 100% SFA, a novel mix design methodology that offers greater simplicity and consistency is established in the present study. The proposed method is further verified by developing different concretes with alkali content to binder (AC/B) ratios ranging from 0.3 to 0.8. Fresh densities range between 1860 and 1930 kg/m3 and maximum compressive strength of nearly 50 MPa was attained after 28 days of ambient curing. The binder penetration and internal curing in SFA indicate that GGBS and FA have a superior synergistic effect on the efficacy of lightweight GPC using SFA.

Utilisation of biomass ash after high-temperature treatment for strengthening purple soil under various curing conditions

As a renewable energy source, biomass has the potential to replace non-renewable, fossil fuels. However, the disposal of the waste biomass ash (generated during energy generation) needs to be studied. While prior studies attempted to utilise composite additives containing biomass ash for soil, the introduction of other additives, such as cement, was an environmental burden. By employing biomass ash composition as the sole additive for strengthening purple soil under various curing conditions using high-temperature treatment, this study maximised its utilisation. The results showed that the unconfined compressive strength (UCS) varied across different curing conditions as the biomass ash content increased. After high temperature treatment at 800 ℃, the biomass ash consistently reinforced purple soil under all the curing conditions. However, the biomass ash stabilisation mechanism differed between dry and humid curing conditions. Under dry curing conditions, the UCS increase depended on the cementing effect of soluble salt and/or insoluble calcite; under humid curing conditions, the UCS change was attributed to the damage to clay minerals, contact mode, and cementing effects of multiple components. Therefore, the 800 ℃ temperature-treated biomass ash can be used alone to reinforce purple soil, inhibiting the soil-water loss. This study presents a novel avenue for utilising waste, biomass ash, with considerable implications for environmental protection and soil stabilisation.

Oxidation Study and Mechanism Analysis of Desulfurization Ash in Dense-Phase Tower

Dense-phase-tower desulfurization technology is an emerging semi-dry flue-gas desulfurization ash process, i.e., the flue gas is allowed to enter the desulfurization tower from the bottom up and, at the same time, is sprayed with a desulfurizing agent that undergoes an acid–base reaction with the flue gas in the ascent process. The calcium sulfite and calcium sulfate produced by the reaction and the part of the desulfurization agent that is not involved in the reaction will enter the subsequent dust removal system, and what is retained is the by-product desulfurization ash. This desulfurization ash contains a large amount of calcium sulfite, which leads to its unstable nature; it is easily oxidized and expands in volume, and, if used in the field of building materials, it will lead to cracking and other problems, so it is difficult to effectively use it. In order to solve this problem, XRF, XRD, and iodometric and other analytical methods were used to determine the specific composition of desulfurization ash, and the muffle furnace and vertical tube furnace were used to study the thermal oxidative modification of calcium sulfite in desulfurization ash, to investigate the effects of the oxygen content, reaction temperature, medium flow rate, and chloride content on the oxidation of calcium sulfite, and to analyze the thermodynamics in the high-temperature oxidation reaction. The results showed that the oxidation rate of calcium sulfite increased with higher reaction temperatures. Increased oxygen content promoted the oxidation rate, particularly at low oxygen levels. The oxidation rate of calcium sulfite correlated positively with the medium flow rate until a rate of 75 mL·min− was reached. At a reaction temperature of 420 °C and a gas flow rate of 85 mL·min−1, the oxidation conversion efficiency exceeded 89%. Chloride content significantly reduced the oxidation rate of calcium sulfite, although this inhibition weakened at temperatures above 500 °C. Kinetic analysis suggested that the oxidation reaction of calcium sulfite predominantly occurred below 500 °C. These findings have both theoretical and practical implications for the thermal oxidation treatment and disposal of desulfurization ash.

Volcanic eruption-inspired co-melting treatment of municipal solid waste incineration fly ash

The resourceful disposal of municipal solid waste incineration fly ash (MSWI FA) is a major global challenge. Inspired by volcanic eruptions, a method to lower the melting point of MSWI FA and to promote heavy metal chlorination volatilization was proposed. The introduction of river mud transformed melting products from crystalline to amorphous, obtaining glass products with low heavy metal residues. The volatilization efficiencies of Cu, Zn, Pb, and Cd reached 82.67 %, 100 %, 100 %, and 100 %, respectively, the heavy metal and salts were enriched in secondary ash. Alkali metal oxide induced the transformation of bridging oxygen to non-bridging oxygen, providing binding site for Cl in the form of Ca-Cl coordination and increasing the chlorine content. Then chlorine reacted with CuO converted from Cu2S and promoted the Cu volatilization. The outcomes fundamentally solved the problem of heavy metal residues in MSWI FA melting treatment, supporting resourceful and harmless treatment of MSWI FA.

Utilization of straw ash as a partial substitute for ordinary Portland cement in concrete

The disposal of agricultural waste ash is a great ecological challenge. This study analyzed the basic properties of corn straw ash and soybean straw ash, encompassing the identification of key oxides, the assessment of particle size distribution, and the performance of thermogravimetric analysis. This study also evaluated the potential of corn straw ash and soybean straw ash to replace cement in mortar and concrete through laboratory tests. The findings indicated that the strength activity index of corn straw ash was higher than soybean straw ash. Furthermore, when these ashes were used as cement replacements, the compressive strength of concrete decreased. Notably, concrete containing corn straw ash exhibited greater strength than concrete with the same substitution amount of soybean straw ash. Specifically, at a 5% substitution level, the compressive strengths of corn straw ash concrete and soybean straw ash concrete were 31.5 and 30.5 MPa, respectively. Additionally, soybean straw ash concrete demonstrated superior resistance to water penetration compared to corn straw ash concrete. Both corn straw ash and soybean straw ash exhibited the potential to enhance the early crack resistance of concrete.

Fly ash treatment via conventional and microwave-assisted organic acid leaching: kinetics and life cycle assessment.

Heedless disposal of oil-based fly ash contributes to the contamination of the air, water, and soil. Acid leaching of industrial solid wastes is recognized as a versatile, cost-effective, and environmentally friendly solid waste treatment approach. The present study investigated the viability of conventional leaching (CL) and microwave-assisted leaching (MAL) of predominant heavy metals from Mazut-burnt fly ash. For this purpose, the practicality of four organic acids with various specifications (ascorbic, gluconic, citric, and oxalic acids) on the dissolution efficiency of fly ash components was examined. Utilization of oxalic acid led to achieving full V recovery, complete Fe removal, and Ni enrichment in the residue in both CL and MAL setups. The Ni content of the sample was enriched from 6% in the calcinated sample to 23.7% in the oxalic acid leaching residue. Using citric acid resulted in the co-extraction of V, Ni, and Fe with nearly 70% V, 50% Ni, and 89% Fe dissolved in CL. The dissolution efficiencies were slightly lower in MAL. Oxalic acid was selected as the most promising organic acid reagent for fly ash treatment, so its CL kinetics was studied and defined by the shrinking particle model. The model showed that the controlling steps in the leaching of V differ over time, changing from a chemical reaction before 60min to fluid film diffusion or mixing afterward. The kinetic study proved MAL as an effective technique in overcoming the leaching kinetic barriers. A life cycle assessment study was conducted to determine the environmental impacts of the proposed process. Accordingly, the MAL using oxalic acid was the most environmentally friendly process among the studied ones, and the utilization of microwaves leads to the reduction of the leaching processes' environmental impacts by decreasing the processing time.

Phytostabilization of fly ash from a coalmine in Botswana and biovalorisation of the recovered Napier grass (Pennisetum purpureum Schumach.)

The disposal of fly ash (FA) from coal power plants polluting the air, soil, and groundwater is a major environmental concern. Phytoremediation to rehabilitate fly ash dumpsites is a promising alternative but has practical concerns about the disposal of harvested biomass. This study investigated the effect of supplementing fly ash with fresh sewage sludge (FSS), aged sewage sludge, food waste, and compost (COM) to enhance the phytoremediation potential of Napier grass and its subsequent utilization for ethanol production. The highest removal of Mn (1196.12 g ha−1) and Ni (128.06 g ha−1) from FA could be obtained when Napier is grown in the presence of FSS and inorganic fertilizer (NPK). In addition, the highest bioethanol yield (19.31 g L−1) was obtained from Napier grown in fly ash with COM + NPK, thus providing additional economic benefits aside from the remediation process. Given the significant levels of heavy metals present in the pulp and bio-slurry after ethanol production, further research is required in this area to determine the best ways to utilize this waste such as converting it into biochar.

Impacts of Fly Ash on Different Vegetation Near Industrial Areas: A Review

Fly ash pollution is created close to Chhattisgarh’s coal-fired thermal power plants, which annually produce 8.7 million metric tonnes of fly ash. Chhattisgarh’s thermal power plants have a number of negative effects, including water contamination from fly ash, soil pollution, and air pollution. Waste from thermal power plants, known as fly ash, poses a number of environmental hazards when released into the atmosphere. On the other hand, because of its high porosity, large specific surface area, and other unique characteristics, fly ash can also be used as a low-cost and highly efficient adsorbent for the treatment of environmental pollutants. There are several methods used to control the spreading and disposal of fly ash. Plants have the capacity to establish fly ash in the soil and also control its spreading. These reviews focus on the impact of fly ash on vegetation and their disposal methods.