Direct Injection Diesel Engine Research Articles

Optimizing diesel engine performance and emissions with diesel-hydrogen mixtures: Impact of injector configuration, angle, and pressure

Several factors affect engine performance, including fuel injection pressure, injection angle, and injector orifice diameter. Any deviation from normal conditions in any of these aspects can disrupt optimal engine performance, resulting in inefficient combustion and increased exhaust emissions. To investigate the effect of injector hole number, injection hole angle, and injection pressure on the performance and emissions of a diesel engine operating on a diesel/hydrogen blend (10 % hydrogen and 90 % diesel), a single-cylinder direct injection diesel engine was used. Three injector nozzle configurations just for diesel injector with different hole diameters (0.6, 0.3, and 0.2 mm) were used at injection angles of 0, 15, and 30 degrees, respectively. Three injection pressures (200, 400, and 600 bar) were tested, with results monitored for brake-specific fuel consumption (BSFC), brake thermal efficiency (BTE), smoke, and NOx emissions.Optimal results were achieved with a maximum injection pressure of 400 bar and a nozzle angle of 15 degrees, resulting in improved engine performance and BTE, along with a 6.5 % reduction in BSFC. Increasing the number of injector holes, injection pressure, and injection angle resulted in reduced BSFC and smoke emissions, but with a significant increase in NOx emissions. Notably, this study deviates from traditional combustion methods by introducing air from a 1.1-atmosphere tank instead of relying solely on natural intake. In addition, hydrogen fuel is introduced into the air manifold via a separate injector with an injection pressure of 20 bar, while diesel fuel is injected directly into the combustion chamber.

Effect of butylated hydroxytoluene nanoparticles blended with biodiesel derived from Bauhinia purpurea linn seed fuelled in a CRDI diesel engine

Effect of butylated hydroxytoluene nanoparticles blended with biodiesel derived from Bauhinia purpurea linn seed fuelled in a CRDI diesel engine

Investigation of biodiesel and its blends fueled diesel engine: An evaluation of the comprehensive performance of diesel engines

The carbon-neutral era and the increasing demand for energy worldwide are imperative for researching alternative energy. At the same time, biodiesel is considered one of the most prospective alternative energy due to its renewable nature and similar properties to diesel. A comparative study of the effects of different proportions of biodiesel-diesel blends (BD10, BD20, BD40, BD60, BD100) on emissions, vibration, lubricant ferrography, and tribological performance of cylinder liner-piston ring (CL-PR) of a direct injection diesel engine (ZS195) was carried out with a baseline of petroleum diesel. The results of the study demonstrated that the appropriate proportion (less than 20 %) of biodiesel significantly improves the comprehensive performance of diesel engines, primarily by combustion optimization and vibration shock reduction. The BD20 fuel blend achieves the best comprehensive diesel engine performance. The higher percentage of biodiesel results in enhanced vibration and severe degradation of CL-PR performance caused by the dilution of the lubricant and erosion of the components by the biodiesel. The study illuminates the mechanism and intrinsic connection of the effects of biodiesel on diesel engine performance. These results will facilitate the understanding of the effects of biodiesel-diesel blends on diesel engine performance and contribute to carbon neutrality in the transportation sector.

Statistical analysis of engine fueled with two identical lower aromatic biofuel blends at various injection pressure

ABSTRACT This work aims to find an alternative source of energy in the engine revolution with more efficiency concerning performance characteristics, emission behavior and combustion characteristics than traditional diesel fuel. In this present work, the following composition is obtained by blending Orange Peel Oil (OPO) and Lemon Peel Oil (LPO) at 20%, traditional diesel fuel at 80% (Blend 1) & OPO and LPO at 12.5%, traditional diesel at 75% (Blend 2) and Use a single-cylinder direct-injection diesel engine to determine the optimal composition across all dimensions. Compared with diesel, there is a noticeable decrease in emissions such as CO, UHC, and smoke and an increase in NOx emission, as well as a significant improvement in thermal efficiency or energy efficiency. BTE was increased 3% while using blend 2 and 2% while using blend 1 at peak load condition when weighted against to traditional diesel fuel. BSFC decreases on both blends when compared to diesel. But NOx is higher when compared to diesel, hence it can be reduced by using additives like BHT, 2EHN and PD at 1.2%, 0.8% and 98% of mixing proportions and run it on a single cylinder engine under varied pressure at 300 bar, 450 bar and 600 bar respectively. The Taguchi optimization is opted to find the best blend in all aspects. It is found that the L16 orthogonal array was used to for this investigation. The NOx has been reduced nearly by 10% when compared to LPO and OPO blends and it gives more efficient results both in efficiency and reduced toxic emissions.

Investigation of lubrication and tribological behaviors in a diesel engine with the new designed flow-guided combustion chamber

Changes to the piston bowl geometry directly affect engine performance, exhaust emissions, combustion characteristics and air/fuel mixture formation. In this study, a new combustion chamber (NCC) geometry for a single cylinder direct injection diesel engine is presented, and experimentally compared with the standard combustion chamber (SCC) geometry. Each combustion chamber was fitted to the engine and performed long-term test for 100 h. The effect of combustion chamber bowl geometry on piston rings and lubricating oil was investigated. Firstly, soot was measured in the engine, and the NCC geometry reduced soot emission by approximately 12.32 % compared to the standard bowl geometry type at part load. With the NCC geometry, homogeneity fresh charge and flame propagation were achieved by providing wall-guided flow. The tribological effect of bowl geometry on the lubricating oil was investigated. In the oil analysis, Al,Ca,Co,Cr,Cu,Fe,Mg,Mn,Mo,Ni and Zn elements were higher in the SCC geometry than in the NCC geometry. Especially at the end of the 100th hour of operation, the presence of elements such as Fe and Al showed an increase in engine wears. The lubricating oil kinematic viscosity for SCC was 111.9 mm2/s at 40 °C and 127.9 mm2/s for NCC. In the new geometry, the flash point temperature of the lubricating oil was measured as 232 °C, while this value in the standard geometry was measured as 222 °C. This showed that the volatility and degree of contamination of the oil was lower with the new geometry. SEM/EDX analysis of the piston rings showed a significant difference between the first and second rings for the two geometries. The wear lines in the standard geometry were found to be deeper and more visible than in the new geometry.

Diesel direct injection and EGR optimization for a syngas-diesel dual-fuel generator operating at constant load

Diesel generators are widely used to produce electricity and heat in remote communities. However, their use contributes to harmful pollutant and greenhouse gas (GHG) emissions, negatively impacting the environment and public health. Syngas, which is a sustainable fuel, can play an important role in the transition from petroleum to renewable fuels. When used in dual-fuel diesel engines, it can contribute to reducing GHG emissions and the cost of transporting diesel, especially for rural and remote communities. This study investigates the effects of optimizing the diesel direct injection (DI) and exhaust gas recirculation (EGR) strategies on the combustion and emission performance of a syngas-diesel dual-fuel generator at constant load. The experiments were conducted using a 30-kW generator with a four-stroke, four-cylinder, turbocharged, and electronically controlled direct-injection diesel engine. The intake manifold of the engine was modified to allow introducing syngas upstream of the turbocharger. The syngas was simulated using individually controlled flow rates of hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), and nitrogen (N2). The syngas flow rate was adjusted to replace 40% of the energy provided by diesel fuel while optimizing the diesel DI parameters such as the pilot injection timing, main injection timing and diesel direct injection rail pressure, as well as the EGR rate. The findings of this study reveal that optimizing diesel injection strategy and appropriately raising the EGR rate have a positive impact on the engine performance and emissions.

Engine Behavior Analysis on a Conventional Diesel Engine Powered with Blends of Lemon Grass Oil Biodiesel–Diesel Blends

<div>Fossil fuel usage causes environmental pollution, and fuel depletion, further affecting a country’s economy. Biofuels and diesel-blended fuels are practical alternatives to sustain fossil fuels. This experimental study analyses lemongrass oil’s performance, emissions, and combustion characteristics after blending with diesel. Lemongrass oil is mixed with diesel at 10 (B10), 15 (B15), and 25% (B25) and evaluated using a 5.20 kW direct injection diesel engine. B10 brake thermal efficiency is 36.47%, which is higher than other blends. The B10 displays an 8.73% decrease in brake-specific fuel consumption compared to diesel. An increase in exhaust gas temperature for B10 than diesel is 4.5%. It indicates that higher lemongrass oil blends decrease exhaust gas temperature. The decrease in average carbon monoxide emissions in B10 to diesel is 22.19%. The decrease in hydrocarbon emissions for B10 to diesel is 7.14%. Biodiesel with lemongrass oil increases nitrogen oxide (NOx) because of increased temperature and poor combustion. Apart from NOx emissions, all other parameters of lemongrass oil blends are suitable for practical diesel applications. The significant findings benefit the biodiesel community toward the efficient combustion of biodiesel blends.</div>

Investigating the impact of alumina nanoparticles in coconut oil distillate biodiesel to lessen emissions in direct injection diesel engine

Petroleum fuels are commonly used for automobiles. However, the continuous depletion and exhaust gas emission causes serious problems. So, there is a need for an alternative eco-friendly fuel. Biodiesel is a type of fuel manufactured through a process called transesterification, which involves converting vegetable oils into a usable form. The process parameters of the transesterification process were optimized using the Taguchi method to achieve maximum biodiesel yield. However, the main problem of biodiesel is its high cost which could be reduced by using low-cost feedstock. To address this challenge, biodiesel (BCFAD) is derived from coconut fatty acid distillate (CFAD), a by-product obtained from refining coconut oil. This work uses BCFAD and BCFAD with Alumina nanoparticles as fuels. Alumina nanoparticles in the mass fraction of 25 ppm, 50 ppm, and 100 ppm are dispersed in BCFAD. The investigation results reveal an increase of 6.5% in brake thermal efficiency for BCFAD with 100 ppm nanoparticles when compared to BCFAD. There is a reduction of 29.29% of hydrocarbon and 34% of Carbon monoxide emissions with BCFAD100 in comparison with diesel. However, there is a marginal increase in NOx emission with the increase in nanoparticles. The heat release rate and cylinder pressure of BCFAD100 are comparable to diesel fuel. It was concluded that the utilization of BCFAD with a nanoparticle dispersion of 100 ppm is suitable for direct use as fuel in diesel engines.

Impact of Using n-Octanol/Diesel Blends on the Performance and Emissions of a Direct-Injection Diesel Engine

This study evaluates the viability of n-octanol as an alternative fuel in a direct-injection diesel engine, aiming to enhance sustainability and efficiency. Experiments fueled by different blends of n-octanol with pure diesel were conducted to analyze their impacts on engine performance and emissions. The methodology involved testing each blend in a single-cylinder engine, measuring engine performance parameters such as brake torque and brake power under full-load conditions across a range of engine speeds. Comparative assessments of performance and emission characteristics at a constant engine speed were also conducted with varying loads. The results indicated that while n-octanol blends consistently improved brake thermal efficiency, they also increased brake-specific fuel consumption due to the lower energy content of n-octanol. Consequently, while all n-octanol blends reduced nitrogen oxide emissions compared to pure diesel, they also significantly decreased carbon monoxide, hydrocarbons, and smoke opacity, presenting a comprehensive reduction in harmful emissions. However, the benefits came with complex trade-offs: notably, higher concentrations of n-octanol led to a relative increase in nitrogen oxide emissions as the n-octanol ratio increased. The study concludes that n-octanol significantly improves engine efficiency and reduces diesel dependence, but optimizing the blend ratio is crucial to balance performance improvements with comprehensive emission reductions.

Numerical Investigation on Energetic, Combustion, and Emissions Parameters of a Diesel Engine Fueled With Diesel/Butanol and Diesel/Pentanol

Abstract In this article, the effect of butanol/diesel and pentanol/diesel blended fuel with different proportions on the energetic, combustion, and emissions parameters of a diesel engine was studied. First, an engine model was established using Diesel-RK software. The modeled engine was a direct injection diesel engine having a fixed compression ratio, injection timing, and speed of 17.5:1, 23 degbTDC, and 1500 rpm, respectively. After that, a set of experiments was conducted using a 5% pentanol and 95% diesel by volume fuel blend maintaining the same operating conditions as the simulation, and the results of the experiment were compared with the numerical result using the same blend. The simulated results were found to be in respectable agreement with experimental findings. The analysis of the simulated results shows that at 100% load using 15% butanol and 85% diesel by volume and 15% pentanol and 85% diesel by volume brake thermal efficiency was increased by 0.96% and 0.8%, respectively. The emission of NOx was reduced by 24.4% and 10.75% on average using butanol and pentanol blends, respectively. The instantaneous heat release rate and ignition delay increase with the higher alcohol–diesel blends, whereas the peak pressure rise and combustion temperature decrease. Smoke emissions were reduced by 3.31–8.75%, and specific particulate matter emissions decreased by 20.9% and 15.07%, respectively, on average with the addition of butanol/pentanol in neat diesel.

Predicting combustion, performance, and emission characteristics of a compression ignition engine utilising coconut oil methyl ester and MoO3 nanoparticles

The present study used a blend of biofuel and nanoparticles to examine the effectiveness and emission properties of a four-stroke, single-cylinder, direct-injection diesel engine with an injection pressure of 250 bar. The use of MoO3 in biodiesel enhances its environmental sustainability and dependability, making it a promising substitute for traditional diesel fuel. The study emphasises the ecological advantages of using a combination of coconut oil and MoO3 to accomplish the production of renewable energy. MoO3 nanoparticles ultimately function as an oxidation catalyst, enhancing combustion. A study with MoO3 nanoparticles at 50 and 100 ppm concentrations was carried out. Utilising a photo spectrometer, stability was determined. The CI engine demonstrated improved thermal efficiency and reduced Fuel Consumption compared to diesel, both at full load conditions and at 64.5 bar pressure. The performance, combustion, and emission parameters were precisely forecasted using Design Expert, exhibiting a robust connection with the testing results. The Rb values for Brake Specific Fuel Consumption (BSFC), Brake Thermal Efficiency (BTE), Peak Cylinder Pressure (P-CA), Net Heat Release Rate (NHRR), Crankcase Heat Release Rate (CHRR), Carbon Monoxide (CO), Unburned Hydrocarbons (UHC), Nitrogen Oxides (NOX), and Smoke Opacity are 0.997, 0.9998, 0.8898, 0.979, 0.9838, 0.9815, 0.9917, 0.9958, and 0.9261 respectively.

Analyzing the effect of carbon nanoparticles on the combustion performance and emissions of a DI diesel engine fueled with the diesel-methanol blend

With the energy crisis and worsening environmental pollution, methanol, as a carbon-neutral fuel, has become a research hotspot in the field of internal combustion engines. This study discusses the influence of different kinds (graphite oxide, GO; multilayer graphene, MG; carbon nanotubes, CNT) and concentrations of carbon nanoparticles, which do not introduce any new elements, added to the diesel-methanol blend on combustion performance and exhaust emissions in a direct injection (DI) diesel engine across diverse operating load conditions. The results showed that the nano-fuels with carbon nano-additives had a better combustion process, with higher peak cylinder pressure (Pmax) and peak heat release rate (HRRmax), and lower ignition delay (ID) and combustion duration (CD). Moreover, the presence of carbon nano-additives resulted in an improvement in brake thermal efficiency (BTE) and a decrement in the break-specific fuel consumption (BSFC). The nano-fuels with GO showed the best optimization effect on the combustion process, followed by MG and CNT. As for emission, the nano-fuels had fewer emissions of CO, HC, and smoke opacity. The nano-fuels with CNT achieved the most significant decrease in emissions of CO and HC. While the presence of GO had the best reduction effect in smoke opacity. However, there was a slight increase in NOx emission. The experimental findings demonstrate that the utilization of carbon nanoparticles in nano-fuels can effectively enhance the application of methanol in internal combustion engines.

Effects of Blended Diesel-Biodiesel Fuel on Emissions of a Common Rail Direct Injection Diesel Engine with Different Exhaust Gas Recirculation Rates.

The aim of the study was to investigate the exhaust gas emissions and fuel consumption of a common rail direct injection (CRDI) diesel engine using mixed diesel (B10) and biodiesel (B20-B100) fuels. The study's primary objective was to determine the effects of blended diesel-biodiesel fuel on CRDI emissions based on different exhaust gas recirculation (EGR) rates, including carbon monoxide (CO), carbon dioxide (CO2), oxygen (O2), nitrogen oxide (NOx), and hydrocarbon (HC) emissions, smoke opacity, exhaust gas temperature, and fuel consumption. The CRDI experiments involved adjusting the different engine speeds (1400-3000 rpm) and EGR rates (0 and 12.5%), which were analyzed to determine their impact on these parameters for both blended diesel and biodiesel fuels. The results showed that under the conditions of no EGR (0%), the CO and HC emissions and the smoke opacity were lower than those with a 12.5% EGR rate for all fuel types and all cases. With 12.5% EGR rate, the O2 emissions and the EGT of the CRDI diesel engine decreased, which resulted in significantly lower NOx emissions because of EGR into the combustion chamber. For the maximum engine speed of 3000 rpm and with no EGR, the CO and HC emissions and the smoke opacity were lower than those with a 12.5% EGR rate for all fuel types. With a 12.5% EGR rate at 3000 rpm, the O2 emissions and the exhaust gas temperature were reduced by 0.07% and 2.27%, respectively, and the NOx emissions were reduced by 2.54%. However, with EGR, the CO and HC emissions and the smoke opacity increased by 7.70%, 18.61%, and 0.4%, respectively. Furthermore, the fuel consumption of pure biodiesel (B100) at 3000 rpm with a 12.5% EGR rate was reduced by 2.81% compared to that with a 0% EGR rate. Because the temperature in the combustion chamber is high enough for the engine to run, the EGR reuses a portion of the exhaust gases and can help to minimize the quantity of fuel in the combustion chamber. As a suggestion based on these observations, biodiesel fuel should not exceed B80 because the viscosity and density of fuel that are too high may affect the fuel injection system, both the injectors, and the pressure pump, causing the injectors to be unable to work correctly. These findings can contribute to the development of strategies and technologies for reducing emissions and improving fuel efficiency in CRDI diesel engines.

A Study on the Effects of Preheating Thevetia Peruviana Biodiesel on the Performance of CI Engine

Biodiesel is becoming increasingly popular as a substitute fuel for compression ignition (CI) engines because of its comparable characteristics to those of diesel and its little environmental impact. The development of diesel engines that run on biodiesel and reduce emissions of pollutants, while also improving thermal efficiency, are key concerns in engine design. The most crucial prerequisites for achieving these are precise and quick air-fuel mixing. However, biodiesel's viscosity is considered a drawback for its application as a substitute fuel for IC engines. Heating can greatly lower the viscosity, which can eliminate the problems caused by excessive viscosity during injection. Hence in this effort, preheated Thevetia Peruviana biodiesel (Methyl Ester) is utilized. The present research aims to examine how preheating biodiesel affects the operation of a direct injection (DI) diesel engine. Engine tests were done on a stationary, single-cylinder, constant speed, naturally aspirated, water-cooled CI engine with a preheated 20% blend of Thevetia Peruviana biodiesel (PH-TPME20 with a conventional jerk type injection system. Engine performance of preheated TPME20 was compared with the unheated 20% blend of TPME and diesel. Preheating reduced the viscosity of the oil, which resulted in a noticeable improvement in engine performance. A considerable drop in emission levels from the engine exhaust gas was noted. The preheating improved combustion characteristics i.e. it lowered the delay period and resulted in quicker release of heat because of improved fuel-air mixing, fuel vaporization, and atomization.

Oxidation-induced variations in the physical and fragmentation characteristics of exhaust soot from DMC-diesel blend: Effect of NO presence in the air atmosphere

This study investigated the changes in physical properties (including morphology, primary particle diameter, fractal dimension, and nanostructure) and fragmentation characteristics of exhaust soot from a modern direct injection diesel engine fueled with diesel (D100) and its blend with 7 vol% of dimethyl carbonate (DMC7) during oxidation processes in air and air-NO atmospheres. Soot particles (D100 soot and DMC7 soot) with specific oxidation degrees (0%, 20%, 50%, and 80%) were produced using a thermogravimetric analyzer, then applied to a high-resolution transmission electron microscopy to generate images. The results exhibited that the morphology for D100 soot and DMC7 soot transformed similarly through oxidation, experiencing an increase in fractal dimension, and a decrease in primary particle diameter, while the introduction of NO to the air accelerated these transformations. Additionally, the nanostructure of both soot particles was gradually ordered through oxidation, as evidenced by longer fringe length, narrower separation distance, and lower tortuosity, while DMC7 soot showed lower order degree compared to D100 soot. Interestingly, the ordering processes of soot nanostructure were decelerated as NO was involved in the oxidation process. Furthermore, the aggregate fragmentation rate for both soot particles declined over the oxidation process, while the possibility for primary particle fragmentation increased overall. Moreover, DMC7 soot exhibited significantly lower aggregate fragmentation rate and higher possibility for primary particle fragmentation than D100 soot at the same oxidation stage. This suggests that DMC7 soot is more susceptible to internal oxidation compared to D100 soot. Furthermore, the presence of NO in the air promoted aggregate fragmentation, while reducing the possibility of primary particle fragmentation.

Energy, exergy, emissions and sustainability assessment of hydrogen supplemented diesel dual fuel turbocharged common rail direct injection diesel engine

The present investigation involves the study of Mahindra & Mahindra Supro BS VI Twin Cylinder Turbocharged CRDI Diesel Engine modified to operate under dual fuel mode utilizing hydrogen as a secondary fuel and neat diesel as a pilot fuel. The tests were carried out at constant speed of 2200 rpm (±20 rpm) under three different loading conditions i.e. BMEP values of 1.38 bar, 3.47 bar and 5.6 bar using H2 enrichment of 0%, 10%, 20%, 30% and 40% respectively along with neat diesel. The performance characteristics of the engine are evaluated using energy-exergy and emissions-based approach along with sustainability studies. The results show that turbocharging significantly improves volumetric and indicated thermal efficiency of engine. At BMEP of 5.6 bar, D + H2 (40%) exhibited highest energy efficiency of 28.94% and exergy efficiency of 28.41% compared to baseline diesel fuel. The irreversibilities due to combustion, mixing, friction and unaccounted reasons was found to be the minimum for D + H2 (40%) at higher BMEP values. Emission analysis revealed that trade-off takes place between nitrogen oxides and smoke opacity (%) with hydrogen substitution to baseline diesel fuel. The sustainability analysis revealed that, D + H2 (40%) has the highest exergy performance coefficient and sustainability index compared to all other cases. From the results, it can be concluded that D + H2 (40%) is the most suitable fuel combination for the Twin Cylinder Turbocharged CRDI Diesel Engine.

Comparative assessment of the effects of higher alcohols/diesel blends on performance and emissions of a direct-injection diesel engine

Comparative assessment of the effects of higher alcohols/diesel blends on performance and emissions of a direct-injection diesel engine

Screening nano additives for favorable NOx/smoke emissions trade-off in a CRDI diesel engine fueled by industry leather waste fat biodiesel blend

The depletion of petroleum reserves and increasing environmental concerns prompted significant research into alternative fuels. This work, biodiesel, is extracted from the byproduct of industrial leather waste fat to generate beneficial energy.The main objective of this study is to enhance common rail direct injection (CRDI) diesel engine outcome characteristics by substituting industrial leather waste fat biodiesel (ILWFB) with the mixing of aluminium nitrate (Al (NO3)3) nanoparticles and graphene oxide nanoplates (GONPS) in the proportion of 50 ppm (parts per million) as catalysts to enhance ignition process. This research found that with the mixing of Al (NO3)3 nanoparticles and GONPS 50 ppm into the ILWFB blend, the in-cylinder pressure increased by 0.463% and 1.5%, and the heat release rate (HRR) improved by 4.19% and 12.04% than diesel and ILWFB blend at maximum load circumstances. Brake thermal efficiency (BTE) increased by 3.1% and 5.27%, and brake specific fuel consumption (BSFC) decreased by 3.57% and 7.14% in D50ILWFB50+Al (NO3)3 50 ppm blend and D50ILWFB50+GONPS 50 ppm blend related to diesel fuel. The carbon monoxide (CO), hydrocarbon (HC), and smoke emissions were reduced by 26.84%, 13.11%, and 5.75% in D50ILWFB50+Al (NO3)3 50 ppm blend and 38.94%, 21.31%, and 9.12% decreased in D50ILWFB50+GONPS 50 ppm blend than diesel fuel. Oxides of nitrogen (NOx) emissions marginally increased by 3.66%, 5.42%, and 8.94% in ILWFB blend, D50ILWFB50+Al (NO3)3, and D50ILWFB50+GONPSrelated to pure diesel at peak load conditions. This work concluded that the nano additives effectively enhanced BTE and decreased BSFC, CO, HC, and smoke emissions in diesel engine applications.

Experimental investigations of CI engine performance using ternary blends of n-butanol/biodiesel/diesel and n-octanol/biodiesel/diesel

This study explored the ternary blends of biodiesel-diesel-n-butanol and biodiesel-diesel-n-octanol on common rail direct injec-tion (CRDI) diesel engines. The compositions of fuels, which varied from 0% to 100%, were altered by up to 5%. On the basis of their properties, these blends were chosen, with various concentrations of alcohol at 5% and 10%, 5% diesel, and the remainder being biodiesel. Two ternary fuel blends of waste cooking oil biodiesel (90–85%), diesel (5%), and butanol (5–10%), namely BD90D5B5 and BD85D5B10, and subsequently, another two ternary similar blends of waste cooking oil biodiesel (90–85%), diesel (5%), and octanol (5–10%), namely BD90D5O5 and BD85D5O10, were used to conduct the experiments. The experiments were done with varying injection pressure from 17° to 29° crank angle (CA) before top dead centre (bTDC). The optimum con-dition for the blends is achieved at 26°CA bTDC for 80% loading. So, the engine trials were conducted on 26°CA bTDC to attain the results. The BD90D5O10 blend achieved the lowest brake specific fuel consumption (BSFC) reading of 0.308 kg/kWh while operating at full load. The maximum brake thermal efficiency (BTE) was 31.46% for BD90D5B5. The maximum heat release rate (HRR) achieved with BD85D5O5 fuel blend was 58.54 J/°CA. The quantity of carbon monoxide that BD85D5B10 created was the lowest (25.86 g/kWh). BD85D5B10 had a minimal unburned hydrocarbon emission of 0.157 g/kWh while operating at full load. Oxides of nitrogen (NOx) were emitted in the maximum quantity by BD85D5O10, which was equal to 6.01 g/kWh. This study establishes the viability of blends of biodiesel and alcohol as an alternative for petro-diesel in the future to meet the growing global energy demand.

Adaptation and Validation of Injection Rate Predictive Model for Solenoid Type Injectors with Different Nozzle Geometry

The present research analyses the injection rate of a direct rail injection diesel engine, focusing specifically on the influence of the nozzles and various operating conditions from real road tests on the rate of injection. A diesel injector test bench was used for feedback with real data from the test vehicle under real road conditions. An analysis of the behaviour of the injection rate was carried out using the zero-dimensional model. This model generated a predictive model that incorporated the five variables identified through a developed multivariate analysis of variance, showing a high correlation of dependence between variations in injection pressure, the diameter of the holes, and the number of holes with greater representativeness. The results obtained showed that the nozzle geometry and the physical properties of the fuel had a direct effect on the injection rate. This analysis enriches the understanding of fuel injection and its effects on diesel engine performance by providing an analysis of the system components that influence the injection rate and generating a simple tool to feed thermodynamic diagnostic models. The proposal model may be used as an input in thermodynamics predictive models and reduce the simulation load in computational fluid dynamics predictive models.