Diode Thermal Desorption-atmospheric Pressure Research Articles

Development of a High-Throughput Affinity Mass Spectrometry (AMS) Platform Using Laser Diode Thermal Desorption Ionization Coupled to Mass Spectrometry (LDTD-MS).

Affinity selection mass spectrometry (MS) or, simply, affinity mass spectrometry (AMS) is a label-free technology that has been used to identify high-affinity ligands of target proteins of interest by screening against small-molecule compound libraries and identifying molecules that are enriched in the presence of the target protein. We have previously applied Agilent Technology's (Santa Clara, CA) RapidFire solid-phase extraction (SPE)-based high-throughput MS technology to screen small-molecule libraries using AMS. However, SPE-based technologies rely on fluidics for desalting and separation prior to mass analysis with attendant high solvent consumption, relatively high sample volume requirements, risk of sample carryover, and frequent maintenance. To address these challenges, we have established an AMS platform using a laser diode thermal desorption-atmospheric pressure chemical ionization (LDTD-APCI) ionization source (Phytronix, Quebec, Canada) coupled with a SCIEX 5600+ TripleTOF MS (Framingham, MA). We also validated a data-independent acquisition (DIA) Sequential Window Acquisition of All Theoretical Mass Spectra (SWATH-MS) method for the robust detection and analysis of small-molecule affinity hits. An informatics platform developed in-house has resulted in a streamlined data analysis workflow for high-throughput AMS screening campaigns and reduced data processing time without compromising data quality. Finally, 68,000 compounds were screened in a single plate and affinity selected hits were confirmed in an orthogonal enzyme activity assay.

Fast analysis of caffeinated beverages using laser diode thermal desorption mass spectrometry (LDTD-MS/MS)

ABSTRACTA rapid method for quantitative caffeine analysis in carbonated and non-carbonated beverages and liquid dietary supplement products was developed based on the direct sample introduction technique of laser diode thermal desorption atmospheric pressure chemical ionisation with tandem mass spectrometry (LDTD-MS/MS). Product samples were diluted with a mixture of methanol, water, and d3-caffeine internal standard. Sample aliquots were filtered, spotted on a metal-lined LDTD microtitre plate, dried, and thermally desorbed for subsequent ionisation and analysis by MS/MS analysis. Each sample required a 6 s desorption, and sample-to-sample analysis time of less than 30 s per sample. Caffeine yielded a linear calibration curve over the range 0.5–100 μg mL−1 (R2 > 0.995). Caffeine recoveries from fortified samples ranged from 97% to 107% with <5% RSD. The caffeine determination was not affected by matrix interferences despite the large range of ingredients, vitamins, sweeteners, extracts, and additives present in the products tested, even though LDTD-MS/MS is a whole-sample desorption technique with no separation of matrix background. The method detection limit was below 0.12 μg mL−1. The method was applied to 33 caffeinated products and LDTD-MS/MS quantitative results closely correlated (R2 > 0.998) with the regulatory standard HPLC-UV method (AOAC Official Method 979.08).

Diclofenac in municipal wastewater treatment plant: quantification using laser diode thermal desorption—atmospheric pressure chemical ionization—tandem mass spectrometry approach in comparison with an established liquid chromatography-electrospray ionization–tandem mass spectrometry method

Diclofenac (DCF), a prevalent non-steroidal anti-inflammatory drug (NSAID) is often detected in wastewater and surface water. Analysis of the pharmaceuticals in complex matrices is often laden with challenges. In this study a reliable, rapid and sensitive method based on laser diode thermal desorption/atmospheric pressure chemical ionization (LDTD/APCI) coupled with tandem mass spectrometry (MS/MS) has been developed for the quantification of DCF in wastewater and wastewater sludge. An established conventional LC-ESI–MS/MS (liquid chromatography-electrospray ionization–tandem mass spectrometry) method was compared with LDTD-APCI-MS/MS approach. The newly developed LDTD-APCI-MS/MS method reduced the analysis time to 12s in lieu of 12min for LC-ESI–MS/MS method. The method detection limits for LDTD-APCI-MS/MS method were found to be 270ngL−1 (LOD) and 1000ngL−1 (LOQ). Furthermore, two extraction procedures, ultrasonic assisted extraction (USE) and accelerated solvent extraction (ASE) for the extraction of DCF from wastewater sludge were compared and ASE with 95.6±7% recovery was effective over USE with 86±4% recovery. The fate and partitioning of DCF in wastewater (WW) and wastewater sludge (WWS) in wastewater treatment plant was also monitored at various stages of treatment in Quebec Urban community wastewater treatment plant. DCF exhibited affinity towards WW than WWS with a presence about 60% of DCF in WW in contrary with theoretical prediction (LogKow=4.51).

Quantitative analysis of poly- and perfluoroalkyl compounds in water matrices using high resolution mass spectrometry: Optimization for a laser diode thermal desorption method

An alternative analysis technique for the quantitation of 15 poly- and perfluoroalkyl substances (PFASs) in water matrices is reported. Analysis time between each sample was reduced to less than 20s, all target molecules being analyzed in a single run with the use of laser diode thermal desorption atmospheric pressure chemical ionization (LDTD/APCI) coupled with high resolution accurate mass (HRMS) orbitrap mass spectrometry. LDTD optimal settings were investigated using either one-factor-at-a-time or experimental design methodologies, while orbitrap parameters were optimized simultaneously by means of a Box–Behnken design. Following selection of an adequate sample concentration and purification procedure based on solid-phase extraction and graphite clean-up, the method was validated in an influent wastewater matrix. Environmentally significant limits of detection were reported (0.3–4ngL−1 in wastewater and 0.03–0.2ngL−1 in surface water) and out of the 15 target analytes, 11 showed excellent accuracies (±20% of the target values) and recovery rates (75–125%). The method was successfully applied to a selection of environmental samples, including wastewater samples in 7 locations across Canada, as well as surface and tap water samples from the Montreal region, providing insights into the degree of PFAS contamination in this area.

High resolution/accurate mass (HRMS) detection of anatoxin-a in lake water using LDTD–APCI coupled to a Q-Exactive mass spectrometer

A new innovative analytical method combining ultra-fast analysis time with high resolution/accurate mass detection was developed to eliminate the misidentification of anatoxin-a (ANA-a), a cyanobacterial toxin, from the natural amino acid phenylalanine (PHE). This was achieved by using the laser diode thermal desorption–atmospheric pressure chemical ionization (LDTD–APCI) coupled to the Q-Exactive, a high resolution/accurate mass spectrometer (HRMS). This novel combination, the LDTD–APCI–HRMS, allowed for an ultra-fast analysis time (<15s/sample). A comparison of two different acquisition modes (full scan and targeted ion fragmentation) was made to determine the most rigorous analytical method using the LDTD–APCI interface. Method development focused toward selectivity and sensitivity improvement to reduce the possibility of false positives and to lower detection limits. The Q-Exactive mass spectrometer operates with resolving powers between 17500 and 140000FWHM (m/z 200). Nevertheless, a resolution of 17500FWHM is enough to dissociate ANA-a and PHE signals. Mass accuracy was satisfactory with values below 1ppm reaching precision to the fourth decimal. Internal calibration with standard addition was achieved with the isotopically-labeled (D5) phenylalanine with good linearity (R2>0.999). Enhancement of signal to noise ratios relative to a standard triple-quadrupole method was demonstrated with lower detection and quantification limit values of 0.2 and 0.6μg/L using the Q-Exactive. Accuracy and interday/intraday relative standard deviations were below 15%. The new method was applied to 8 different lake water samples with signs of cyanobacterial blooms. This work demonstrates the possibility of using an ultra-fast LDTD–APCI sample introduction system with an HRMS hybrid instrument for quantitative purposes with high selectivity in complex environmental matrices.

Laser diode thermal desorption mass spectrometry for the analysis of quinolone antibiotic residues in aquacultured seafood

Veterinary drug residue analysis of meat and seafood products is an important part of national regulatory agency food safety programs to ensure that consumers are not exposed to potentially dangerous substances. Complex tissue matrices often require lengthy extraction and analysis procedures to identify improper animal drug treatment. Direct and rapid analysis mass spectrometry techniques have the potential to increase regulatory sample analysis speed by eliminating liquid chromatographic separation. Flumequine, oxolinic acid, and nalidixic acid were extracted from catfish, shrimp, and salmon using acidified acetonitrile. Extracts were concentrated, dried onto metal sample wells, then rapidly desorbed (6 s) with an infrared diode laser for analysis by laser diode thermal desorption atmospheric pressure chemical ionization with tandem mass spectrometry (LDTD-MS/MS). Analysis was conducted in selected reaction monitoring mode using piromidic acid as internal standard. Six-point calibration curves for each compound in extracted matrix were linear with r(2) correlation greater than 0.99. The method was validated by analyzing 23 negative samples and 116 fortified samples at concentrations of 10, 20, 50, 100, and 600 ng/g. Average recoveries of fortified samples were greater than 77% with method detection levels ranging from 2 to 7 /g. Three product ion transitions were acquired per analyte to identify each residue. A rapid method for quinolone analysis in fish muscle was developed using LDTD-MS/MS. The total analysis time was less than 30 s per sample; quinolone residues were detected below 10 ng/g and in most cases residue identity was confirmed. This represents the first application of LDTD to tissue extract analysis. Published 2012. This article is a US Government work and is in the public domain in the USA.

Development of a new multi-residue laser diode thermal desorption atmospheric pressure chemical ionization tandem mass spectrometry method for the detection and quantification of pesticides and pharmaceuticals in wastewater samples

A new solid phase extraction (SPE) method coupled to a high throughput sample analysis technique was developed for the simultaneous determination of nine selected emerging contaminants in wastewater (atrazine, desethylatrazine, 17β-estradiol, ethynylestradiol, norethindrone, caffeine, carbamazepine, diclofenac and sulfamethoxazole). We specifically included pharmaceutical compounds from multiple therapeutic classes, as well as pesticides. Sample pre-concentration and clean-up was performed using a mixed-mode SPE cartridge (Strata ABW) having both cation and anion exchange properties, followed by analysis by laser diode thermal desorption atmospheric pressure chemical ionization coupled to tandem mass spectrometry (LDTD-APCI-MS/MS). The LDTD interface is a new high-throughput sample introduction method, which reduces total analysis time to less than 15s per sample as compared to minutes with traditional liquid-chromatography coupled to tandem mass spectrometry (LC–MS/MS). Several SPE parameters were evaluated in order to optimize recovery efficiencies when extracting analytes from wastewater, such as the nature of the stationary phase, the loading flow rate, the extraction pH, the volume and composition of the washing solution and the initial sample volume. The method was successfully applied to real wastewater samples from the primary sedimentation tank of a municipal wastewater treatment plant. Recoveries of target compounds from wastewater ranged from 78% to 106%, the limit of detection ranged from 30 to 122ngL−1 while the limit of quantification ranged from 90 to 370ngL−1. Calibration curves in the wastewater matrix showed good linearity (R2≥0.991) for all target analytes and the intraday and interday coefficient of variation was below 15%, reflecting a good precision.