Diode-pumped Solid-state Laser Technology Research Articles

Repetition rate stabilization of an optical frequency comb based on solid-state laser technology with an intra-cavity electro-optic modulator.

The repetition rate stabilization of an optical frequency comb based on diode-pumped solid-state laser technology is demonstrated using an intra-cavity electro-optic modulator. The large feedback bandwidth of such modulators allows disciplining the comb repetition rate on a cavity-stabilized continuous-wave laser with a locking bandwidth up to 700 kHz. This surpasses what can be achieved with any other type of actuator reported so far. An in-loop integrated phase noise of 133 mrad has been measured and the PM-to-AM coupling of the electro-optic modulator has been investigated as well.

Radiation hard mode-locked laser suitable as a spaceborne frequency comb.

We report ground-level gamma and proton radiation tests of a passively mode-locked diode-pumped solid-state laser (DPSSL) with Yb:KYW gain medium. A total gamma dose of 170 krad(H(2)O) applied in 5 days generates minor changes in performances while maintaining solitonic regime. Pre-irradiation specifications are fully recovered over a day to a few weeks timescale. A proton fluence of 9.76·10(10) cm(-2) applied in few minutes shows no alteration of the laser performances. Furthermore, complete stabilization of the laser shows excellent noise properties. From our results, we claim that the investigated femtosecond DPSSL technology can be considered rad-hard and would be suitable for generating frequency combs compatible with long duration space missions.

Ultra-stable microwave generation with a diode-pumped solid-state laser in the 1.5-μm range

We demonstrate the first ultra-stable microwave generation based on a 1.5-μm diode-pumped solid-state laser (DPSSL) frequency comb. Our system relies on optical-to-microwave frequency division from a planar-waveguide external cavity laser referenced to an ultra-stable Fabry–Perot cavity. The evaluation of the microwave signal at ~10 GHz uses the transportable ultra-low-instability signal source ULISS®, which employs a cryo-cooled sapphire oscillator. With the DPSSL comb, we measured −125 dBc/Hz phase noise at 1 kHz offset frequency, likely limited by the photo-detection shot-noise or by the noise floor of the reference cryo-cooled sapphire oscillator. For comparison, we also generated low-noise microwave using a commercial Er:fiber comb stabilized in similar conditions and observed >20 dB lower phase noise in the microwave generated from the DPSSL comb. Our results confirm the high potential of the DPSSL technology for low-noise comb applications.

High-power diode-pumped solid-state lasers

Diode-pumped solid-state laser technology is reviewed with an emphasis on laser materials and concepts important to high power systems with excellent beam quality. A first principal approach to power scaling is taken in order to summarize and compare the wide variety of laser architectures. Successful approaches are highlighted and directions for future work are discussed.

Wide-field fluorescence lifetime imaging with optical sectioning and spectral resolution applied to biological samples

. Wide-field fluorescence lifetime imaging with spectral resolution and optical sectioning has been performed to achieve five-dimensional fluorescence microscopy. Spectral filtering has been shown to have the potential to provide functional information about biological tissue by simultaneously measuring the spectral/lifetime signature of the sample. The potential to use multispectral imaging to separate cellular components spatially by their different emission wavelengths has also been demonstrated thus reducing artefacts in the calculated lifetime maps. The instrument is based on diode-pumped solid-state laser technology and an ultrafast gated optical image intensifier. Also reported is the use of a picosecond blue laser diode as the excitation source to produce a fluorescence lifetime microscope with a footprint of less than 0.25m2.

Whole-field five-dimensional fluorescence microscopy combining lifetime and spectral resolution with optical sectioning

We report a novel whole-field three-dimensional fluorescence lifetime imaging microscope that incoporates multispectral imaging to provide five-dimensional (5-D) fluorescence microscopy. This instrument, which can acquire a 5-D data set in less than a minute, is based on potentially compact and inexpensive diode-pumped solid-state laser technology. We demonstrate that spectral discrimination as well as optical sectioning minimize artifacts in lifetime determination and illustrate how spectral discrimination improves the lifetime contrast of biological tissue.

Laser Doppler optical air-data system: feasibility demonstration and systems specifications

A compact laser Doppler velocimeter with diode-pumped solid-state laser technology at 1.06 µm and a novel solid-block beam-splitting interferometer was demonstrated. This system allows for accurate Doppler velocity measurements even in a vibration environment. A comparison of the backscatter measurements with a backscatter sonde from the University of Wyoming showed excellent agreement. Based on demonstrated performance and technology projection, the system specifications of an optical air-data system at 2.015 µm are determined, and a detailed design concept is presented. In addition, the potential for a multifunctional sensor that can determine air data and detect wind shear and wake vortices is addressed.

Airborne lidar for profiling of surface topography

A lidar system is described that measures laser pulse time-of-flight and the distortion of the pulse waveform for reflection from earth surface terrain features. This instrument system is mounted on a high-altitude aircraft platform and operated in a repetitively pulsed mode for measurements of surface elevation profiles. The laser transmitter makes use of recently developed short-pulse diode-pumped solid-state laser technology. Aircraft position in three dimensions is measured to submeter accuracy by use of differential Global Positioning System receivers. Instrument construction and performance are detailed.