Differential Scanning Calorimetry Analysis Research Articles

Preparation and characterization of polyphenol-loaded microcapsules based on zeaxylated protein

Pomegranate seeds are rich in polyphenols, known for their significant health benefits. In this study, we developed microcapsules to encapsulate pomegranate seed polyphenols (PSP) using a combination of zeaxylated protein (Zein) and chitosan (Cs). The optimization process involved a Zein to Cs volume ratio of 1:1, a chitosan concentration of 1.0 mg·mL−1, and a polyphenol concentration of 2.0 mg·mL−1. Scanning electron microscopy confirmed the formation of Zein/Cs/PSP complex coacervates, indicating the successful encapsulation. Fourier-transform infrared spectroscopy provided further evidence of electrostatic attraction between PSP and the Zein/Cs matrix. Differential scanning calorimetry analysis demonstrated the successful incorporation of PSP into the Zein/Cs wall material. Moreover, the encapsulated core material exhibited exceptional storage stability and retained its antioxidant activity. Notably, more than 85% of the encapsulated PSP remained intact after 5 hours of simulated intestinal fluid digestion. This study underscores the potential of pomegranate seeds for comprehensive utilization in food engineering.

Influence of alkali treatment on thermal stability of polyester composites reinforced with Bambusa maculat fibers

The various species of bamboo plants cultivated in Indonesian people's plantations are apus bamboo (Gigantochloa apus) (GA), wulung bamboo (Gigantochloa atroviolacea) (GV), and tutul bamboo (Bambusa maculat) (BM). Apart from being used as a craft material and household utensils, bamboo can be made into natural fiber as a reinforcement for polyester composites. In this research, Bambusa maculat fiber was used. In this work, BM fibers were treated with Alkali with NaOH solutions with concentrations of 2, 5, and 8% by weight respectively at room temperature. The next procedure is that the BM fibers are used as composite reinforcing fibers, arranged unidirectional the polyester composites. The manufacturing technique is using hot pressing molding technique. The effect of alkali concentration on the thermal performance of polyester composites was examined using differential scanning calorimetry (DSC) and thermogravimetric (TG) analysis. As the result, the alkaline treatment of BM bamboo fiber with a NaOH concentration of 5%, causes the BM bamboo fiber as reinforcement and matrix to have a tight interface and strong interfacial bonding, allowing the composite to have the best thermal stability among other composites.

Research on Alloy Design and Process Optimization of Al–Mg–Zn-Cu-Based Aluminum Alloy Sheets for Automobiles with Secured Formability and Bake-Hardenability

In this study, the compositional design of high-formability, high-bake-hardening Al–Mg–Zn-Cu-based aluminum alloys was carried out, and process conditions were established to secure mechanical properties under harsh conditions for Al–Mg–Zn-Cu-based alloys. Using JMatPro13.0 for precipitation phase simulation, the optimal pre-aging temperature and time of the design composition were selected. Through the introduction of pre-aging, it was confirmed that no over-aging phenomena occurred, even after bake-hardening, and it was confirmed that it could have mechanical properties similar to those of test specimens subjected to traditional heat treatment. Through DSC (Differential Scanning Calorimetry) and TEM (Transmission Electron Microscope) analyses, it was found that pre-aging provided sufficient thermal stability to the GP (Guinier–Preston) zone and facilitated transformation to the η’-phase. In addition, it was confirmed that, even under bake-hardening conditions, coarsening of the precipitation phase was prevented and number density was increased, thereby contributing to improvements in the mechanical properties. The designed alloy plate was evaluated as having excellent anisotropy properties through n-value and r¯-value calculations, and it was confirmed that a similar level of formability was secured through FLC (Forming Limit Curve) comparison with commercial plates.

Ameliorative delivery of docetaxel and curcumin using PEG decorated lipomers: A cutting-edge in-vitro/ in-vivo appraisal

The development of a PEG-decorated lipid-polymer hybrid system camouflaged with natural and synthetic chemotherapeutic moieties is an influential approach melding the biomimetic properties of long-circulating vesicles to utilize different mechanisms to dwindle the tumor growth. Therefore, a safe and efficient lipid-coated nano-particulate system (LCNPs) was proposed to investigate the in-vitro, ex-vivo and in-vivo demeanors of such amalgamation.Docetaxel loaded PLGA nanoparticles (DTX-NPs) were prepared by solvent evaporation while curcumin liposomes were mapped out using the film hydration method. Physicochemical characterizations were executed in terms of size, surface morphology, differential scanning calorimetry (DSC) and fourier-transform infrared spectroscopy (FTIR). In-vitro cytotoxicity was effectuated using MCF-7 cell line. Hemolysis, erythrocyte aggregation and acute in-vivo toxicity were carried out to establish the biocompatibility. The hydrodynamic diameters of samples were in the nano-range and corresponded to the findings of scanning electron microscopy (SEM) and atomic force microscopy (AFM). The absence of distinctive peaks of DTX-NPs in FTIR and DSC analysis of LCNPs depicts the shielding of the lipid bilayer over the nanoparticle. Cytotoxicity induced by the LCNPs represented the efficient delivery of cargo to the tumor cells. LCNPs also exhibited the least toxicity under ex-vivo and in-vivo circumstances compared to free drugs. Additionally, histological studies showed no evidence of substantial necrosis. Additionally, histological studies showed no evidence of notable necrosis.

A Comprehensive Study on Structural and Optical Properties of Zinc Selenide/Poly Ortho-methoxyaniline Hybrid Thin Films Deposited by Chemical Bath Deposition and Plasma Polymerization Techniques

Hybrid thin films hold dominant importance in various technological applications due to their synergistic effects between inorganic and organic materials. In this study, inorganic–organic hybrid thin film has been produced where the inorganic layer of zinc selenide (ZnSe) is deposited first through chemical bath deposition technique and the organic layer is deposited onto the inorganic layer using a capacitively coupled plasma polymerization technique. The ZnSe layer deposited for one hour has been used as the base layer and plasma polymerized (PP) o-methoxyaniline (OMA) has been deposited for different deposition durations. The experimental results showed that thickness of the the hybrid films increases with the organic layer deposition time. The field emission scanning electron microscope exhibited a large number of pores on the surface of the ZnSe film, which are significantly covered up when organic PPOMA is deposited onto it. The energy-dispersive X-ray confirms the constitutional elements of the hybrid films and X-ray diffraction study indicates the enhancement of crystallinity of the film. Differential scanning calorimetry and thermogravimetric analysis specify that hybrid films are thermally more stable (up to 396 °C) compared to pure ZnSe film (351 °C), probably due to higher conjugation in the PP organic layer. The direct optical band gaps of the deposited hybrid thin films are found to increase from 2.4 to 2.80 eV with the increase of organic layer onto ZnSe film. Consequently, the Urbach energy decreases from 0.94 to 0.66 eV with the deposition of hybrid film for different time durations. The outcomes of this study suggest that the hybrid films would have enormous potential as passive thin films for photovoltaic cells, sensing and optical devices.

The Role of WO3 Nanoparticles on the Properties of Gelatin Films

Gelatin films are very versatile materials whose properties can be tuned through functionalization with different systems. This work investigates the influence of WO3 nanoparticles on the swelling, barrier, mechanical, and photochromic properties of gelatin films. To this purpose, polyvinylpirrolidone (PVP)-stabilized WO3 nanoparticles were loaded on gelatin films at two different pH values, namely, 4 and 7. The values of swelling and solubility of functionalized films displayed a reduction of around 50% in comparison to those of pristine, unloaded films. In agreement, WO3 nanoparticles provoked a significant decrease in water vapor permeability, whereas the decrease in the values of elastic modulus (from about 2.0 to 0.7 MPa) and stress at break (from about 2.5 to 1.4 MPa) can be ascribed to the discontinuity created by the nanoparticles inside the films. The results of differential scanning calorimetry and X-ray diffraction analysis suggest that interaction of PVP with gelatin reduce gelatin renaturation. No significant differences were found between the samples prepared at pH 4 and 7, whereas crosslinking with glutaraldehyde greatly influenced the properties of gelatin films. Moreover, the incorporation of WO3 nanoparticles in gelatin films, especially in the absence of glutaraldehyde, conferred excellent photochromic properties, inducing the appearance of an intense blue color after a few seconds of light irradiation and providing good resistance to several irradiation cycles.

Phenyl-Substituted Cage Silsesquioxane-Based Star-Shaped Giant Molecular Clusters: Synthesis, Properties, and Surface Segregation Behavior.

The crystallinity, solubility, and physical properties of polyhedral oligomeric silsesquioxane (POSS) compounds are highly dependent on their organic substituents. We previously synthesized a series of isobutyl-substituted star-shaped POSS derivatives with aliphatic chain linkers of different length. In this study, we prepared C3- and C6-linked phenyl-substituted star-shaped POSS derivatives (3Ph-C3 and 3Ph-C6) by the hydrosilylation of heptaphenylallyl- and hexenyl-POSS (1a and 1b) and octadimethylsiloxy-Q8-silsesquioxane (Q8M8H) (2), respectively, and their properties were compared with those of the corresponding isobutyl-substituted derivatives (5iBu-C3 and 5iBu-C6). Although 3Ph-C6 was only soluble in chloroform and insoluble in tetrahydrofuran (THF) and toluene, 3Ph-C3 was soluble even in THF and toluene, suggesting that the shorter linkers of the derivative afford a wider range of solvents for dissolution. Differential scanning calorimetry analysis showed that 3Ph-C3 exhibited a baseline shift at 190 °C and an endothermic peak at 316 °C. However, no clear baseline shift was observed for 3Ph-C6. Thermogravimetric analysis showed that the shorter linker in the phenyl-substituted star-shaped POSS derivative significantly increased the decomposition temperature compared with the longer linker. The annealed cast film of 3Ph-C3 at 340 °C above its melting temperature formed a transparent film even after cooling to room temperature. However, an opaque whitish film was formed in the case of 3Ph-C6. Poly(methyl methacrylate) (PMMA) films containing 2 wt % 3Ph-C3 and 3Ph-C6 were prepared by casting their chloroform solutions onto glass substrates overnight at room temperature. The static water contact angle measurements and XPS analysis for the castings film containing 3Ph-C3 and 3Ph-C6 suggested that degree of the segregation amount of 3Ph-C3 was larger than that of 3Ph-C6. The shorter linker length in the phenyl-substituted star-shaped POSS derivative, 3Ph-C3, with its greater predicted solubility in PMMA, exhibited entropy-driven surface segregation.

Formulation, Optimization and Evaluation of Solid Dispersion of Deferasirox Using Factorial Design

Deferasirox, an oral iron-chelating agent, is a poorly soluble drug (Biopharmaceutical Classification System class II) having insufficient solubility in physiological fluids resulting in low bioavailability of the drug. The idea behind the present study was to explore the prospects of solid dispersion as a prolific method to enhance the dissolution rate of drug using a water soluble polymer. The solid dispersion was prepared by the solvent evaporation technique using Polyvinyl pyrrolidone with different drug to carrier and solvent ratio. Formulations were characterized through attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), differential scanning calorimetry (DSC), Powder X-ray diffraction (XRD), and in vitro release studies. A 32 factorial design was implemented to obtain optimum solubility, % yield, and optimization of solid dispersion (SD) also quantitates the influence of PVP on the solubility and dissolution profile. Thedrug-to-carrier and solvent ratio was chosen as independent variable, while %yield, drug content, and saturation solubility were chosen as dependent variables. The results showed that the optimized formulation of SD-DFX was able to significantly enhance its solubility. The SD containing a dispersion of Deferasirox with PVP show an exceptional rise in the solubility. This study describes the development of solid dispersion that significantly improved the solubility and bioavailability of DFX. The FTIR studies indicate the interaction between the drug and polymer. The DSC and XRD analysis indicated that the drug was in an amorphous state when dispersed in the polymer. It is resolved that the SD method significantly improves the solubility and dissolution rate, which could also be exploit for other poorly water soluble drug candidates. Keywords: Deferasirox , Polyvinyl pyrrolidone, solid dispersion, Factorial design, Solubility

Zein/fucoidan-coated phytol nanoliposome: preparation, characterization, physicochemical stability, in vitro release, and antioxidant activity.

To improve phytol bioavailability, a novel method of magnetic stirring and high-pressure homogenization (HPH) combination was used to prepare zein/fucoidan-coated phytol nanoliposomes (P-NL-ZF). The characterization, the simulated in vitro digestion, and the antioxidant activity of these phytol nanoliposomes from the different processes have been studied. Based on the results of dynamic light scattering (DLS) and gas chromatography-mass spectrometer (GC-MS) analysis, P-NL-ZF prepared through the combination of magnetic stirring and HPH exhibited superior encapsulation efficiency at 76.19% and demonstrated exceptional physicochemical stability under a series of conditions, including storage, pH, and ionic in comparison to single method. It was further confirmed that P-NL-ZF by magnetic stirring and HPH displayed a uniform distribution and regular shape through transmission electron microscopy (TEM). Fourier-transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC) analysis showed that electrostatic interactions and hydrogen bonding were the primary driving forces for the formation of composite nanoliposomes. Additionally, an in vitro digestion study revealed that multilayer composite nanoliposomes displayed significant and favorable slow-release properties (58.21%) under gastrointestinal conditions compared with traditional nanoliposomes (82.36%) and free phytol (89.73%). The assessments of chemical and cell-based antioxidant activities demonstrated that the coating of zein/fucoidan on phytol nanoliposomes resulted in enhanced effectiveness in scavenging activity of ABTS free radical and hydroxyl radical and mitigating oxidative damage to HepG2 cells. Based on our studies, the promising delivery carrier of zein/fucoidan-coated nanoliposomes is contributed to the encapsulation of hydrophobic natural products and enhancement of their biological activity. © 2024 Society of Chemical Industry.

Thermal Analysis of the Biodegradable Polymer PVA/PEO Blends

Poly(vinyl alcohol) (PVA) and poly(ethylene) oxide (PEO) are widely used water-soluble and biodegradable polymers that possesses high biocompatibility. In this work PVA/PEO blends were prepared via solution casting method, where the solvent was water. After drying, samples were characterized by differential scanning calorimetry (DSC) and thermogravimetric analysis (TG). Since DSC could not confirm the possible intermolecular interaction between PVA and PEO, infrared spectroscopy with Fourier transform (FT-IR) was utilized. Finally, the TG analysis revealed that degradation of PVA/PEO blends proceeds through tree stages, similar as neat PVA. Contrary, neat PEO thermally degrade through only one stage showing better thermal stability in comparison to PVA.

A comprehensive study on the thermal properties and chemical characterization of 1,3,5‐trinitroso‐1,3,5‐triazine (R‐Salt)

Abstract1,3,5‐trinitroso‐1,3,5‐triazine (R‐Salt) is an insensitive energetic that has previously been used as an improvised explosive. The work presented here is a comprehensive study on the thermal properties and chemical characterization of R‐Salt. Thermal analysis was performed via differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) which found both crude and recrystallized R‐Salt have similar thermal properties but the selected lid impacted both the thermal profile and onset temperature. Chemical characterization performed via Raman, Fourier‐transform Infrared (FT‐IR), nuclear magnetic resonance (NMR) spectroscopy and high‐resolution mass spectrometry indicate that recrystallization does not quantitatively improve the purity of crude R‐Salt., The reported NMR 2D‐HSQC, FT‐IR, and Raman spectra are the first to be reported within the published literature, as to the authors’ knowledge.

Mechanical and thermal characterization of elastomer modified polypropylene hybrid composites reinforced with hazelnut shell and wollastonite fillers

AbstractThe demand for sustainable and recyclable materials in industrial applications has led to a surge in interest in green composites, particularly those incorporating natural fillers derived from agro‐food industry waste. This study investigates the mechanical and thermal properties of polypropylene (PP) hybrid composites filled with hazelnut shell and wollastonite, along with the effect of styrene‐ethylene/butylene‐styrene (SEBS) and SEBS‐g‐maleic anhydride (SEBS‐g‐MA) compatibilizers. Various characterization techniques, including tensile, flexural, and impact tests, as well as differential scanning calorimetry (DSC), thermogravimetry (TGA), and scanning electron microscopy (SEM) analyses, were employed to evaluate the composites. Results demonstrate that the addition of wollastonite significantly improves mechanical properties, while hazelnut shell filler affects thermal behavior and stability. SEBS and SEBS‐g‐MA compatibilizers enhance impact resistance; however, they lead to a decrease in other mechanical properties. DSC and TGA analyses demonstrate changes in crystallization behavior and thermal stability due to filler and compatibilizer incorporation. SEM microstructure images show the distribution of SEBS and SEBS‐g‐MA within the composite structure, affecting mechanical and thermal properties. Overall, this study highlights the importance of filler selection, compatibilizer addition, and their distribution in attaining desired properties for industrial applications. Future research should focus on optimizing formulations for specific uses and assessing long‐term performance under real‐world conditions.

"Dissolve-on-Demand" 3D Printed Materials: Polymerizable Eutectics for Generating High Modulus, Thermoresponsive and Photoswitchable Eutectogels.

Solvent-free photopolymerization of vinyl monomers to produce high modulus materials with applications in 3D printing and photoswitchable materials is demonstrated. Polymerizable eutectic (PE) mixtures are prepared by simply heating and stirring various molar ratios of N-isopropylacrylamide (NIPAM), acrylamide (AAm) and 2-hydroxyethyl methacrylate (HEMA). The structural and thermal properties of the resulting mixtures are evaluated by 1D and 2D NMR spectroscopy as well as differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). UV photocuring kinetics of the PE mixtures are evaluated via in situ photo-DSC and photorheology measurements. The PE mixtures cure rapidly and display storage moduli that are orders of magnitude greater than equivalent copolymers cured in an aqueous medium. The versatility of these PE systems is demonstrated through the addition of a photoswitchable spiropyran acrylate monomer, as well as applying the PE formulation as a stereolithography (SLA)-based 3D printing resin. Due to the hydrogen-bonding network in PE systems, 3D printing of the eutectic resin is possible in the absence of crosslinkers. The addition of a RAFT agent to reduce average polymer chain length enables 3D printing of materials which retain their shape and can be dissolved on demand in appropriate solvents. This article is protected by copyright. All rights reserved.

Biopolymer-Based Hydrogel Incorporated with Naproxen Sodium and Lidocaine Hydrochloride for Controlled Drug Delivery.

Sodium hyaluronate (HA) is a natural polysaccharide. This biopolymer occurs in many tissues of living organisms. The regenerating, nourishing, and moisturizing properties as well as the rheological properties of HA enable its application in the pharmaceutical industry as a carrier of medicinal substances. The aim of this work was to assess the release of naproxen sodium (Nap) in the presence of lidocaine hydrochloride (Lid) from the biopolymer-based hydrogels and to determine the respective kinetic parameters of this process. The possible interaction between the HA polysaccharide carrier and the selected drugs was also investigated. Three hydrogels containing Nap and Lid with different concentrations of the biopolymer were prepared. The release of Nap was studied by employing USP apparatus 5. The infrared study and differential scanning calorimetry analysis of physical mixtures and dried formulations were performed. The highest amount of Nap was released from the formulation with the lowest concentration of the biopolymer. The most representative kinetic model that described the dissolution of Nap was obtained through the Korsmeyer-Peppas equation. The release rate constants were in the range of 1.0 ± 0.1 × 10-2 min-n-1.7 ± 0.1 × 10-2 min-n. Lid did not influence the dissolution of Nap from the formulations tested; however, in the desiccated samples of assessed formulations, the interaction between the polysaccharide and both drugs was observed.

Evaluation of the Combustion Properties and Catalytic Activity of MgAlB Energetic Ternary Particles

ABSTRACT Boron powder possesses significant potential for use as a combustible agent in energetic materials, owing to its superior combustion thermodynamic properties. However, the powder’s tendency to form an oxide layer on its surface results in delayed ignition, reduced combustion efficiency, and compromised energy advantage. To enhance the ignition and combustion properties of boron powder, we prepared boron-based energetic composites containing flammable metals (MgxAl1-xB2) through high-temperature sintering. These were then characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), energy dispersive spectroscopy (EDS). The combustion heat of these alloy powders were measured using an oxygen bomb calorimeter, while their catalytic performance on the thermal decomposition of ammonium perchlorate (AP) was analyzed using differential scanning calorimetry (DSC) and differential thermal analysis (DTA). The results indicate that compared with boron, the MgxAl1-xB2 powders are more flammable, require less oxygen, exhibit a higher combustion efficiency and exothermic advantage. Especially, the Mg0.9Al0.1B2 and MgB2 alloy exhibit optimal combustion heat values of 39,094.92 and 37,693.90 J·g−1, respectively. They significantly enhance the thermal decomposition of AP and reduce the activation energy by over 20%.

Differential scanning calorimetric evaluation of the human plasma in patients using cilostazol for the treatment of intermittent claudication (a preliminary study)

AbstractThis preliminary study employs differential scanning calorimetry (DSC) to assess alterations in human plasma composition in patients treated with cilostazol for intermittent claudication. Cilostazol, an antiplatelet and vasodilator agent, is commonly prescribed to moderate symptom associated with PAD caused by reduced peripheral blood flow. Patients selected according to study protocol were treated with cilostazol for a duration of three months. At the visits, subjects exercised by a standard walking test controlled by physiotherapist. The blood samples were taken on day 0 (control), day 15, 1, 2 and 3 months. Through DSC analysis, we investigate potential thermodynamic changes in plasma composition induced by cilostazol treatment. As a result of the treatment, the pain-free walking distance improved significantly in the first 3 months. The thermal unfolding of the human plasma showed a correlation with the walking improvement. Our findings provide insights into the systemic effects of cilostazol and its impact on plasma constituents in the context of PAD and intermittent claudication management.

Coumarin Schiff base derivatives with 4′-alkoxy biphenyl-4-carboxaldehyde: Synthesis, mesomorphic studies and DFT calculations

Two homologous series of coumarin Schiff base derivatives with 4′-alkoxy biphenyl-4-carboxaldehyde have been designed and synthesized. All the compounds were analyzed IR, 1H NMR, 13C NMR, ESI-MS and CHN analysis followed by mesomorphic properties polarizing optical microscopy (POM) and differential scanning calorimetry (DSC) analysis. In the first homologous series BPS(6–16), Schiff base of 7-alkoxy-3-aminocoumarin with 4′-alkoxy biphenyl-4-carboxaldehyde, alkoxy chain length was varied systematically at both end of the molecules such as n = 6,8,10,12,14,16. In this series, BPS(6–10) (n = 6,8,10) exhibited enantiotropic nematic(N) and smectic C (SmC) mesophase and turned to monophasic on increasing the chain length n = 12,14,16 in BPS(12–16) with stable SmC mesophase. While in the second homologous series 10BPU(2–16), systemic variation of alkoxy chain length was carried out at coumarin end only (n = 2–18) and 4′-decyloxy-biphenyl-4-carboxaldehyde was used for Schiff base formation. In the this series, early member of the series with n = 2,3 showed enantiotropic very stable (∼ 145 °C) nematic mesophase, while N as well as SmC mesophase were observed for n = 4–8 at, whereas with increase of chain length stability of nematic mesophase was decreased and that of SmC was increased. Higher membered analogous 10BPU(12–16) exhibited SmC mesophase with stability in the rage of 130–160 °C. VT-XRD analysis was also confirmed the tilted SmC mesophase in this class of compounds. For both the series, all compounds were studied for the DFT calculations as well as literature molecules with similar variations. Based on the calculated structural (length, aspect ratio) and electronic (dipole moment, polarizability) parameters were correlated with mesomorphic behaviour observed for literature compounds and compounds from both the series followed by the detailed discussion.

Desosomes and desimicelles − a novel vesicular and micellar system for enhanced oral delivery of poorly soluble drug: Optimization of in vitro characteristics and in vivo performance

This study introduces two innovative nanocarrier systems to improve oral drug delivery. Desosomes and desimicelles combine Deep eutectic solvent (DES) with vesicular or micellar nanosystems, respectively. These novel nanosystems integrate the DES solubilization potency for administering drugs with low aqueous solubility and the vesicular and micellar systems to bypass physiological barriers and improve poor drug bioavailability. Lornoxicam (LRX) is a BCS class II anti-inflammatory with limited aqueous solubility and rapid clearance. Desosomes and desimicelles were prepared and successfully optimized. The optimization depended on particle size, zetapotential, entrapment efficiency, and solubility. The optimized desosomes (LRX-DES-V) and desimicelles (LRX-DES-M) were pictured by transmission electron microscope. Differential scanning calorimetry (DSC) and FTIR analysis indicated the successful inclusion of LRX inside each system. Invitro LRX release profiles revealed controlled release of LRX-DES-V and LRX-DES-M, with more sustained release by the later one. In-vivo study, inflammation was induced using a carrageenan rat model, and the anti-inflammatory effect of LRX-pure, marketed product, traditional niosomes, LRX-DES-V & LRX-DES-M were determined using inhibition %, serum inflammatory cytokines, and histopathology. After 4 h of induction, LRX-DES-M (68.05%) showed a significant inhibition compared to LRX-DES-V (63.57%). LRX-DES-M also showed a better reduction in COX2, PGE2, and TNF-α (1.25-fold, 1.24-fold, and 1.36-fold inhibition), respectively, compared to LRX-DES-V. We can conclude that LRX-DES-V and LRX-DES-M showed better effects than all other groups and that LRX-DES-M might be more effective than LRX-DES-V.

Preparation, Cure, Characterization, and Mechanical Properties of Reactive Flame-Retardant Cyanate Ester/Epoxy Resin Blends and Their Carbon Fiber Reinforced Composites

This study explores the formulation space of flame retardant thermoset polymers, specifically involving blends of epoxy and cyanate ester (EP/CE) and a reactive phosphorus-based flame retardant, poly (m-phenylene methylphosphonate) (PMP). Two CE monomers were investigated, each blended with the same epoxy monomer (DGEBA) in a 1:1 weight ratio. The impact of phosphorus concentration on the neat (neat meaning no fibers were present) resin blends was characterized using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The flammability and mechanical characteristics were assessed using micro-combustion calorimetry (MCC) and dynamic mechanical analysis (DMA). Carbon fiber composite panels were successfully fabricated using a wet layup process and autoclave curing with a fiber volume fraction (Vf) of approximately 0.5. DMA testing of the cured composite laminates pinpointed that the average Tg of the EP/CE blend was reduced with PMP addition by up to 39 °C at a phosphorous level of 3 wt%. Cone calorimetry tests confirmed the effectiveness of the flame retardant by reducing the peak Heat Release Rate (HRR) by approximately 27%. The integration of PMP into EP/CE only marginally reduced the 3-point flexural strength (6–15%) and modulus (7–13%) relative to baseline samples.

Effect of temperature on the mechanical behavior of glass fiber reinforced with hollow glass particle-filled epoxy composites

The design of marine ships and aircraft components with hollow glass particle-filled fiber-reinforced composites demands an understanding of their performance under outdoor conditions. The continuous glass fiber-reinforced epoxy matrix filled with hollow glass particles in the range of 0–0.3 vol fraction was prepared by the compression molding machine. The influence of temperature exposure on the mechanical behavior of glass fiber-reinforced hollow glass particle composites was studied by conducting tensile and flexural tests. The temperature exposure varying from room temperature up to 60 °C was used to investigate the effect of service temperature on the hollow glass particle-filled fiber composite specimens. Differential scanning calorimetry (DSC) analysis was conducted to study the glass transition behavior of the composites. The incorporation of microspheres in the glass fiber composites gradually reduced the tensile and flexural strength, while their specific values increased as increasing the microspheres. The hollow glass particle-filled fiber composites tested at 60 °C exhibited a decrease in tensile and flexural strength compared with room temperature. As the température of the test spécimens was nearer to the glass transition value, the polymer chain was softened, leading to a reduction in strength. In contrast, the modulus values remain unaffected by increasing the temperature to 60 °C.