Differential Difference Current Conveyor Transconductance Amplifier Research Articles

Tunable floating and grounded memristor emulator Model

ABSTRACT A Differential Difference Current Conveyor Transconductance Amplifier (DDCCTA) based resistor tunable memristor emulator has been proposed in this work. The emulator can be used in both grounded and floating circumstances. The proposed design incorporates only one active block along with few passive components. Moreover, the circuit can operate in both incremental and decremental modes, by simply changing the input ports. The circuit demonstrates all the characteristics of an ideal memristor up to 6 MHz. The proposed model has been simulated using TSMC 0.18m process parameter and occupies an area of 51 × 42.5 m2 chip-area, excluding capacitor. The circuit’s reliability has been verified by studying non-ideal, non-volatile, Monte-Carlo, process corner variations analysis. The circuit applicability has been tested through series/parallel combinations. To validate the experimental demonstration, AD844AN and CA3080 have been used to make a prototype, which shows good agreement with theoretical and simulation results.

A novel memristor emulator design and universal biquad filter application using second generation high swing differential current conveyor transconductance amplifier in 130 nm CMOS process

Memristors have drawn a significant wide spread attention from the research community since past decade due to their high-speed operational potential in analog applications. However, it has been difficult to achieve the memristor behavior directly from solid state solution and state of the art. This work presents a novel emulator design to mimic the memristor behavior. A generic and simple emulator circuit for a voltage controlled memristor is presented using a differential difference current conveyor transconductance amplifier (DDCCTA), which is based on a versatile second-generation current conveyor methodology. A high-swing (up to ±600 mA at the output) and low power implementation design effort for DDCCTA is kept in 130 nm RF-CMOS process with dual power supply mode. The functional simulations have been performed in SPICE environment using Advanced Design System (Keysight Technology), which showed a good alignment to the memristor emulator’s I-V characteristic at 1 KHz and 10 KHz. Proposed DDCCTA then implements the memristor operation with compatible specifications. Finally, the memristor operation and potential has been verified by its application in high-speed active filter operations. A universal biquad section has been presented which employs the designed memristor emulator, with 30 mW of power dissipation with ±1.5 V supply.

Voltage-mode biquadratic filters using single DDCCTA

This paper presents two voltage-mode universal biquadratic filters based on a single differential difference current conveyor transconductance amplifier (DDCCTA). Each of the proposed circuits comprises a single DDCCTA combined with passive components that can realize lowpass (LP), highpass (HP), bandpass (BP), bandstop (BS), and allpass (AP) filtering responses from the same configuration. The first proposed configuration can be used as either a high-input impedance single-input four-output multifunction filter or three-input four-output universal filter. The second proposed circuit with single-input five-output is slightly modified from the first proposed configuration that can simultaneously realize LP, HP, BP, BS, and AP filtering responses. The proposed circuits enjoy the features of orthogonal tunable of resonance angular frequency and quality factor, only using grounded capacitors, and low active and passive sensitivities. Experimental and H-Spice simulation results are given to confirm theoretical analyses.

A Voltage-Mode Universal Biquadratic Filter Using DDCCTA

This paper presents a new voltage-mode (VM) universal biquadratic filter using differential difference current conveyor transconductance amplifier (DDCCTA) as an active element. The circuit employs one DDCCTA, two floating resistors and two floating capacitors which can realize five biquadratic filters, namely low-pass (LP), band-pass (BP), band-stop (BS), high-pass (HP) and all-pass (AP) into one single topology. For realizing these filtering functions, passive component-matching conditions, inverting-type and/or doubling-input signal requirements and changing circuit configuration are absent. The natural angular frequency and quality factor of the filter can be orthogonally controlled deliberately. The VM biquadratic filter using grounded passive components with high-input and low-output impedances can be obtained by adding an additional DDCCTA or differential difference current conveyor (DDCC). The simulation results with 0.5[Formula: see text][Formula: see text]m CMOS process from MIETEC are given to confirm the theoretical predictions and the experimental results are also included to verify the workability of the proposed structure.

High‐input impedance voltage‐mode differential difference current conveyor transconductance amplifier‐based universal filter with single input and five outputs using only grounded passive components

This study presents a novel high-input impedance voltage-mode differential difference current conveyor transconductance amplifier (DDCCTA)-based universal filter with a single input and five outputs. The proposed configuration uses two DDCCTAs, two grounded capacitors and two grounded resistors. It simultaneously provides voltage-mode lowpass, bandpass, highpass, bandstop and allpass filtering responses, without passive component-matching conditions or restrictions on input signals. The proposed circuit offers high-input impedance and low active and passive sensitivities, and uses only grounded capacitors and resistors.

Single-input four-output voltage-mode universal filter using single DDCCTA

An electronically tunable universal voltage-mode biquadratic filter with single input and four outputs using one differential difference current conveyor transconductance amplifier (DDCCTA), two resistors and two grounded capacitors is proposed. All the five standard biquadratic filter functions; lowpass (LP), bandpass (BP), highpass (HP), bandstop (BS) and allpass (AP), can be obtained from the circuit configuration. The LP, BP and HP are simultaneously available without component matching condition. By imposing component choice, the BS and AP responses can also be realized from the same circuit configuration. In addition, the proposed circuit provides an electronic control of its natural angular frequency (ω0) and quality factor (Q) by adjusting the bias current of the DDCCTA. The simulation results together with the ideal values are also given to demonstrate the performance of the proposed circuit.

Voltage-mode universal filter with one input and five outputs using DDCCTAs and all-grounded passive components

This paper presents a versatile voltage-mode universal active filter with one input and five output terminals. The proposed circuit is based on using the recently reported active building block, namely differential difference current conveyor transconductance amplifier (DDCCTA). It employs two DDCCTAs as active elements together with two resistors and two capacitors as passive elements, which are all grounded. The circuit simultaneously realizes all the five standard biquadratic filter functions; i.e., lowpass (LP), bandpass (BP), highpass (HP), bandstop (BS) and allpass (AP), without changing circuit topology. The proposed circuit also has the advantage of high-input impedance terminal, and exhibits electronic tunability of its important parameters through the bias current of the DDCCTA as well as low sensitivity performance. PSPICE simulations using 0.5μm MIETEC CMOS process are used to validate the theoretical predictions.

Differential Difference Current Conveyor Transconductance Amplifier: A New Analog Building Block for Signal Processing

A new active building block for analog signal processing, namely, differential difference current conveyor transconductance amplifier (DDCCTA), is presented, and performance is checked through PSPICE simulations which show the usability of the proposed element is up to 201 MHz. The proposed block is implemented using 0.25 μm TSMC CMOS technology. Some of the applications are presented using the proposed DDCCTA, namely, a voltage mode multifunction filter, a current mode universal filter, an oscillator, current and voltage amplifiers, and grounded inductor simulator. The feasibility of DDCCTA and its applications is confirmed via PSPICE simulations.