Diethyl Bis Hydroxymethyl Malonate Research Articles

Preparation and Properties of Plasticized Poly(lactic acid) Films

Poly(lactic acid), PLA, was blended with monomeric and oligomeric plasticizers in order to enhance its flexibility and thereby overcome its inherent problem of brittleness. Differential scanning calorimetry, dynamic mechanical analysis, transmission electron microscopy, and tensile testing were used to investigate the properties of the blends. Monomeric plasticizers, such as tributyl citrate, TbC, and diethyl bishydroxymethyl malonate, DBM, drastically decreased the T(g) of PLA, but the blends showed no morphological stability over time since rapid cold crystallization caused a size reduction of the amorphous domains in PLA. Consequently, the ability of PLA to accommodate the plasticizer diminished with the increase in crystallinity and migration of the plasticizer occurred. Increasing the molecular weight of the plasticizers by synthesizing oligoesters and oligoesteramides resulted in blends that displayed T(g) depressions slightly smaller than with the monomeric plasticizers. The compatibility with PLA was dependent on the molecular weight of the oligomers and on the presence or not of polar amide groups that were able to positively interact with the PLA chains. Aging the materials at ambient temperature revealed that the enhanced flexibility as well as the morphological stability of the films plasticized with the oligomers could be maintained as a result of the higher molecular weight and the polar interactions with PLA.

2-Aryl-5,5-bisoxazolin-2-yl[1,3]dioxanes as solution phase and immobilised ligands for highly enantioselective cyclopropanations

2-Aryl-5,5-bisoxazolin-2-yl[1,3]dioxanes 5, which can be easily prepared in three steps from diethyl bishydroxymethylmalonate, amino alcohol and an aromatic aldehyde, have been used for the copper catalysed asymmetric cyclopropanation of styrene with ethyl diazoacetate in up to 99% ee for the trans-cyclopropane. Grafting onto a bromo-Wang resin produced an immobilised ligand 9 which gave the trans-cyclopropane in 65% ee.

Plasticization of poly(lactic acid) with oligomeric malonate esteramides: Dynamic mechanical and thermal film properties

AbstractTwo oligomeric malonate esteramides and an oligomeric malonate ester were synthesized with the intention to plasticize poly(lactic acid), PLA. The synthesis was performed by reacting diethyl bishydroxymethyl malonate (DBM) with adipoyl dichloride and one of two diamines, that is, triethylene glycol diamine (TA) and polyoxypropylene glycol diamine (PA), or triethylene glycol (TEG), giving three platicizing agents denoted as DBMATA, DBMAPA, and DBMAT, respectively. The synthesis products were characterized by size exclusion chromatography and Fourier transform infrared spectroscopy, and blended with PLA at a concentration of 15 wt %. Dynamic mechanical analysis, differential scanning calorimetry, and tensile testing were used to investigate the physical properties of films from the resulting blends. All three plasticizers decreased the glass transition temperature of PLA, and the largest decrement was observed for PLA/DBMATA. Films of DBMATA and DBMAT showed enhanced flexibility in strain at break as compared to neat PLA. Subsequently, it was found that thermal annealing of the plasticized materials (4 h at 100°C) encouraged cold crystallization, inducing phase separation in the blends, and caused them to regain the brittleness of neat PLA. On the other hand, by aging (6 weeks) the blends at ambient conditions, cold crystallization could be avoided and the flexibility in the films maintained. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 992–1002, 2005

Thermomechanical film properties and aging of blends of poly(lactic acid) and malonate oligomers

AbstractMalonate oligomers were synthesized as plasticizers for poly(lactic acid) (PLA). Esterification reactions were performed between diethyl bishydroxymethyl malonate (DBM) and either adipoyl dichloride or succinyl dichloride. Two molar masses were obtained within each series. Blending was carried out with PLA and the four oligomers as well as the monomeric unit from the syntheses (DBM). Dynamic mechanical analysis and differential scanning calorimetry were used to investigate the viscoelastic mechanical and thermal film properties of the blends. All the investigated plasticizers reduced the glass‐transition temperature of PLA, and the plasticization effect was better for the plasticizers of low molar mass. However, the amorphous domains of PLA became saturated with plasticizer at a certain concentration, and phase separation occurred. A higher molar mass of the plasticizer caused this saturation to occur at lower plasticizer concentrations. Subsequently, the aging of the blends at the ambient temperature for 4 months induced phase separation in the blends containing DBM, whereas those with an oligomeric plasticizer were stable and remained compatible with PLA within the aging period. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2140–2149, 2004

Synthesis of thioether phosphocholine analogues.

The synthesis of thioether phospholipids, which represent a new class of antitumor agents, is reported here. In particular, the route of synthesis of 3-hexadecylmercapto-2-methoxymethylpropyl-2'-trimethylammoni o-ethyl phosphate (BM 41.440, Ilmofosine), one of the most potent cytostatic/cytotoxic derivatives, is described in detail. Starting with diethyl bis-hydroxymethylmalonate, ethyl 2-phenyl-1,3-dioxane-5-carboxylate is formed via diethyl 2-phenyl-1,3-dioxane-5,5-dicarboxylate and 5-ethoxycar-bonyl-2-phenyl-1,3-dioxane-5-carboxylic acid. Reduction of ethyl 2-phenyl-1,3-dioxane-5-carboxylate with LiAlH4 affords 5-hydroxymethyl-2-phenyl-1,3-dioxane. Alkylation with dimethyl sulfate gives 5-methoxymethyl-2-phenyl-1,3-dioxane. The ring structure then is opened by N-bromosuccinimide, resulting in the formation of 3-bromo-2-methoxymethylproply benzoate. Reaction of 3-bromo-2-methoxymethylpropyl benzoate with the sodium salt of hexadecanethiol leads to 3-hexadecylmercapto-2-methoxy-methylpropanol, which is reacted with a cyclic chlorophosphate to give the corresponding phosphorylated 3-hexadecylmercapto-2-methoxymethylpropanol. Treatment with trimethylamine yields BM 41.440. This compound already has been tested in clinical phase I/II trials in West Germany.