Dielectric Measurements Research Articles

Dielectric spectroscopy with machine learning integrated approach to analysis the influence of N:P ratio on algae growth modeling for forecasting

The task of monitoring algal biomass is a significant challenge in contemporary environmental conservation. A novel technique called dielectric spectroscopy with machine learning integration is an intelligent approach to address this challenge. This work optimized a machine learning supervised PCA, Hierarchical cluster analysis & linear regression model -strengthen the real-time dielectric spectroscopy approach to study the influence of N:P ratios on a model algae Desmodesmus sp. growth for forecasting. As a primary feature, different N:P concentrations (1:1, 2:1, 3:1, 1:2, and 1:3) were utilized to characterize the relationship between dielectric (S11(dB) & ε'') and conventional UV–vis spectroscopy properties (OD686 & Chl-a). The dielectric measurements of S11(dB) & ε'' are consistent with the OD686 & Chl-a value. Highest Desmodesmus sp. OD686 0.87, 0.76 recorded at N:P 3:1, 2:1 ratio respectively. The machine learning based PCA, Hierarchical cluster analysis and linear regression model were applied and found at 0–8 days incubation Desmodesmus sp. growth biomass negatively corelated with S11(dB) & ε“ and positively correlatedly with OD686 & Chl-a respectively, with R2 values > 0.95. While for the 0&8days measured ε”& S11(dB) were −6.169&-0.4765; −7.956 &-0.6775 respectively, the linear regression model was applied to predicted OD686 for 0&8 days was 0.299, 0.234; 0.817, 0.716 respectively, at the ratios N:P (3:1) and the RMES were 0.0047 & 0.0319 respectively. This analysis revealed that the machine learning based integrated approach has high accuracy. Thus, Dielectric spectroscopy and machine learning-integrated method could strengthen to the real-time monitoring of algal biomass or predicting to control the N:P ratios to protecting aquatic ecosystem.

Effect of La2O3 as sintering aid on the structural, mechanical & electrical properties of Y2O3

Yttrium oxide (Y2O3) is a potential material in the development of transparent polycrystalline ceramics (PTCs). PTCs have possible applications in laser-materials, scintillators, Infrared windows, opto-electronic devices, displays etc. To obtain these, the ceramic must have a symmetric crystal structure, high purity and density. Highly dense ceramics require sophisticated sintering procedures as well as optimum sintering additives such as Lanthanum Oxide (La2O3) and Zirconium Oxide (ZrO2). In this manuscript, La2O3 is used as a sintering to embrace the sintering of Y2O3 with the aim to bring down the sintering temperature and systematically study the opto-electrical properties. La2O3 substituted Y2O3 (LaxY2−xO3, where, x = 0, 3, 6 and 9 at.%) ceramics are made, using co-precipitation method were examined for structural, morphological, physico-chemical and electrical properties by using XRD, SEM, TGA-DSC, and dielectric measurements. The obtained results serve as guidelines for the use of Y2O3 as a pathway to new dimensions opto-electronic applications.

Structural Elucidation and Evaluation of Magnetic and Dielectric Properties of Lu–La Co‐substituted M‐Type Hexagonal Ferrites Synthesized by Chemical Co‐precipitation Method

In this research, LuxLaySr1–yFe12–xO19, an M‐type strontium ferrite, is synthesized using the coprecipitation method with precursor chemicals. The samples undergo analysis for structure, morphology, and elemental composition through X‐ray diffraction (XRD) and scanning electron microscopy (SEM). Magnetic and dielectric properties are determined using a vibrating sample magnetometer (VSM) and a dielectric property measurement instrument (LCR), respectively. The primary objective of this study is to enhance the dielectric performance of the samples through rare‐earth element doping. The XRD analysis reveals that the samples display a hexagonal single‐phase magnetoplumbite crystal structure. SEM micrographs illustrate a regular hexagonal structure of the grains. VSM analysis affirms LuxLaySr1–yFe12–xO19 as a hard magnetic material with a high coercivity. As the rare‐earth element content increases, the coercivity of the samples significantly decrease from 2065.3 to 910.3 Oe. Dielectric property analysis demonstrates that augmenting the rare‐earth element (Lu–La) content notably increases the relative dielectric constant of the samples. In the low‐frequency region, the relative dielectric constant ranges from 6.71 × 103 to 1.28 × 105, while in the high‐frequency region, it ranges from 3.09 × 103 to 2.03 × 104. Samples doped with rare‐earth elements exhibit a high dielectric constant and low coercivity, rendering them suitable for applications in electromagnetic shielding materials. This can help reduce interference from magnetic fields on internal components while blocking electromagnetic waves.

Structural characterization of LLDPE/MgO insulation composites in terms of space charge accumulation in an HVDC field

This study addresses the critical role of insulation materials in high-voltage direct current (HVDC) transmission systems, emphasizing the challenges associated with space charge accumulation and slow polarization effects. The primary objective of this study is to investigate the utilization of linear low-density polyethylene (LLDPE) in High Voltage Direct Current (HVDC) applications, with a focus on enhancing its performance through the incorporation of magnesium oxide (MgO) nanoparticles. The research employs various techniques, including X-ray diffraction, nuclear magnetic resonance, broadband dielectric spectroscopy, conductivity measurements and pulse electroacoustic measurements, to analyse the internal structure, crystallinity, and space charge dynamics of LLDPE/MgO nanocomposites. The results demonstrate that controlled MgO incorporation optimizes the internal electric field, improving the electrical properties without significantly altering the charge decay rate. The multidimensional approach of the study provides valuable insights into tailored modification of insulation materials for enhanced HVDC transmission performance, considering both electrical and structural aspects.

(1-x)(Na₀.₅Bi₀.₅)TiO₃-xCaTiO₃ ceramics: Investigating structural and microstructural features for enhanced dielectric properties

(1-x)(Na₀.₅Bi₀.₅)TiO₃-xCaTiO₃ Lead-free piezoelectric systems, positioned near the morphotropic phase boundary, were synthesized for varying compositions (x = 0.0, 0.05, 0.10, 0.15, and 0.20) using the solid-state reaction route. This study delves into the comprehensive investigation of the compositional effects on phase, structure, and electrical characteristics. Specifically, a morphotropic phase boundary (MPB) involving rhombohedral (R3c) and orthorhombic (Pnma) structures was seen in a (1-x)NBT-xCT crystal structure close to the composition of x = 0.10. Information on the pure phase formation and grain size of the intended composite system has been obtained using Rietveld refinement of the X-ray diffraction (XRD) diagram as well as scanning electron microscopy (SEM). The impact of the CT phase on the NBT lattice was investigated through an analysis of the charge density distribution. Using Williamson-Hall plots from XRD data, the average particle diameter was estimated to be between 131.87 nm and 136.54 nm. The relative permittivity increases with the addition of Ca2+, according to dielectric measurements. All ceramics exhibit a diffuse phase transition near (Tm) with a diffusivity range of 1.5–1.8, and a downward shift in depolarization temperature (Td). At the morphotropic phase boundary (MPB), excellent dielectric properties were observed at x = 0.10, which are attributed to the presence of both rhombohedral and orthorhombic structures as well as an appropriate particle size. The conduction process at different temperatures is thermally activated, as determined by the frequency-dependent ac conductivity.

Achieving giant field-induced strain in BS-modified BNKT lead-free ferroelectric ceramics

Bi0.5Na0.5TiO3-Bi0.5K0.5TiO3 (BNT-BKT) binary systems with the morphotropic phase boundary (MPB) are promising candidates for piezoelectric actuators. However, pure BNT-BKT ceramics commonly exhibit unfavorable electric field-induced strain, which is insufficient to meet the requirements for actuator applications. Rare earth-containing dopants have been extensively explored to modify various materials due to their unique optical, magnetic, and electronic properties. Here, by introducing rare earth ion-containing dopants BiScO3 (BS), the electrical properties of Bi0.5(Na0.84K0.16)0.5TiO3 (BNKT) lead-free ferroelectric ceramics have been modified. X-ray diffraction (XRD) and scanning electron microscopy (SEM) results suggest that the introduction of BS results in an increase in tetragonal (T) phases, reduced grain sizes, and uniform morphologies. Ferroelectric measurements demonstrate that the BS-containing ceramics show slimmer hysteresis loops. The BNKT-2BS ceramics show a noteworthy improvement in electric field-induced strain, with bipolar and monopolar strains of 0.58% and 0.68%, respectively, which are almost 4 times and 6 times higher than those of pure BNKT ceramics. Furthermore, the corresponding normalized strain (d33*) also achieves high values of 967 pm/V and 1133 pm/V, respectively. Temperature-dependent dielectric measurements reveal that BS-containing ceramics exhibit good relaxor characteristics with frequency dispersion and diffuse phase transitions. This study presents a sufficient and feasible strategy for the optimization of strain performance in large displacement actuator applications.

Photoconductive TiO2 Dielectrics Prepared by Plasma Spraying

Titanium dioxide coatings (TiO2) were sprayed using a water-stabilized plasma gun (WSP) to form robust self-supporting bodies with the character of a ceramic disc capacitor (CDC). Agglomerated nanometric powder was used as feedstock. Argon was applied for powder feeding as well as coating–cooling to minimize the influence of ambient air. Stainless steel was used as a substrate, and the coatings were released after cooling. A more than three-millimeter-thick self-supporting TiO2 plate was observed using HR-TEM and SEM. Porosity was studied by image analysis on polished sections. Thermal post-treatment on the coating was conducted at a rather low temperature of 500 °C. The results of the subsequent dielectric measurement showed high permittivity, but this was strongly frequency-dependent and accompanied by a progressively decreasing loss tangent. On the other hand, the plasma-sprayed TiO2 exhibited persistent DC photoconductivity under and after illumination with a standard bulb.

Enhanced liquid crystal performance through alkoxybenzoic acid doping

ABSTRACT This study investigates the impact of doping agents, 4-octyloxybenzoic acid (8OBA) and 4-octyloxy-3-fluoro benzoic acid (8OBAF), on the thermodynamic and electro-optical properties of the nematic liquid crystal 5CB. The differential scanning calorimetry, dielectric, and polarising optical microscopic measurements revealed intriguing properties. The doped liquid crystal samples exhibit higher phase transition temperatures, increasing birefringence, and order parameters. Dielectric measurements disclose reduced free ion concentration with 8OBA and increased concentration with 8OBAF in the liquid crystal matrix. The threshold voltage, switching time, and rotational viscosity were also diminished in the 5CB + 8OBA mixture, whereas these parameters were increased in the 5CB + 8OBAF mixture due to the strong intermolecular interaction with liquid crystals. The results presented here demonstrate that 8OBA dopant can be used to achieve high thermal stability of the nematic liquid crystal phase with fast response times and low threshold.

Effect of Hot Pressing on the Optical, Thermal, and Dielectric Properties of Solution Cast Prepared Nanocomposite Films Based on a Poly(Vinylidene Fluoride-co-Hexafluoropropylene) and Poly(Ethylene Oxide) Blend Matrix with Dispersed Zinc Oxide Nanoparticles

In our research described herein, the hot pressing treatment at 90 °C under 2 tons of pressure on solution cast polymer nanocomposite (PNC) films based on a host matrix of poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) and poly(ethylene oxide) (PEO) with varying polymer blend compositions (20, 50, and 80 wt% P(VDF-HFP) or PEO) and 2 wt% zinc oxide (ZnO) nanofiller, was performed; the effects of this treatment and the composition variations on the optical, thermal, and dielectric properties was explored. The ultraviolet-visible wavelength range study revealed slightly reduced absorbance and a little increased energy band gap after the hot pressing of the nanocomposite films. Differential scanning calorimetry of the solution cast-hot pressed (SC-HP) PNC films explained the reduced thermal stability of the poly(ethylene oxide) crystallites and also the degree of crystallinity. The broadband dielectric measurements of these materials, at 27 °C, confirmed significant changes in various dielectric polarization processes, demonstrating a large redistribution of constituent interfaces by the hot press treatment. Additionally, the 90 °C hot pressed PNC film of equal polymer compositional ratio was further hot pressed at 130 °C and 160 °C, step by step, and characterized to examine the variations in dielectric properties. The properties of these thermally treated composite films are discussed concerning their use for flexible device applications.

Influence of Congored on the Optical, Dielectric and Thermal Behavior of Polymethyl Methacrylate and Polyvinyl Chloride

Polymethyl methacrylate (PMMA)/Congo Red (CR) and polyvinyl chloride (PVC)/CR composite films were prepared on optical glass by the drop method for optical measurements and also prepared as tablets under pressure for dielectrical measurements. The optical transmission spectra measurements for PMMA and PVC film doped with CR showed a highly absorption in the ultraviolet-visible (UV-Vis) optical range (at 353 nm and 518 nm) and considerably blocking in broad visible range (190 nm–640 nm). PMMA/CR and PVC/CR composite films containing congo red at a concentration of 1 wt% showed maximum absorption bands at 290 nm and 416 nm, but their transmittance percentages were reasonably reduced compared to those of pure PMMA and PVC. Both of composites indicated high transmittances between 640 nm and 800 nm. The optical constants of the PMMA/CR and PVC/CR composite films such as optical band energy gaps (Eg) estimated using Tauc’s model, refractive index and reflectance (%) were calculated. UV–Vis, Fourier transform infrared spectroscopy (FTIR) and Thermogravimetry Analysis (TGA) measurements were used to confirm the breakdown of the -N = N- azo group bonds attached to the aromatic ring as a result of thermal decomposition of CR at 500 °C, and it was suggested that N2 gas was eliminated from the CR above 360 °C. The dielectric plots showed that the dielectric constant increased when the CR is doped up to 70 wt% in the polymer matrices. A further increase in the doping concentration of CR resulted in an increase of the dielectric constant. The dielectric constant decreased with an increase in the frequency for all of the samples. The ac (alternating current) conductivity values of PMMA and PVC showed an increase with increasing CR dopant in the polymer composites, while the ac conductivity values were found to be values between those of the pure polymers and CR.

Low temperature relaxor behaviour of SrBi1.5La0.5Nb2O9 ceramics

Bismuth layered compound with the composition SrBi1.5La0.5Nb2O9 has been prepared using conventional solid-state reaction method. Crystallographic planes have been identified using X-ray diffraction studies. The dielectric studies have been done as a function of frequency and temperature. Low temperature dielectric measurement shows phase transition in which peak dielectric constant shifts from 260K to 280K with the increase in frequency from 1 kHz to 1 MHz. Room temperature dielectric constant has been found to be nearly frequency independent for this composition making it a potential candidate for the capacitor applications. The prepared ceramic was modelled using the Vogel – Fulcher relationship.

Flexible bandwidth-enhanced metamaterial absorbers with epoxy/graphene nanoplatelets-silver nanowire polymer composites as substrates

The realm of flexible devices has seen considerable advancement in recent technology due to their ability to bend and conform to particular shapes. Flexible metamaterial absorbers offer the advantage of combining the features of conventional metamaterials with the attributes of conformal systems, thereby opening new avenues in electromagnetic technology. This work involves the realization of flexible metamaterial absorbers with epoxy/graphene nanoplatelets-silver nanowire (GnP-AgNW) polymer composites as substrates; with a bandwidth enhancement achieved by incorporating losses in the substrate and combining resonances in the unit cell. A novel in-situ technique is employed to synthesize the nanohybrid GnP-AgNW (GA) with different weight percentages of AgNWs grown on GnP (GAx; x = 10, 15, 20 wt%). The dielectric measurements of the polymers showed that an increase in weight percentages of AgNWs in the composite enhanced the dielectric constant as well as losses of the polymer (εr՛: 7.7 to 8.8 and εr՛՛: 0.62 to 1.12). The numerical study on the designed flexible metamaterial absorbers with these substrates of thickness 1.4 mm showed a maximum absorptivity of 99% with a bandwidth (having absorption >90%) varying between 1.2 and 1.86 GHz. The experimental measurements on the fabricated metamaterial absorber were found to match the simulation results closely. The polymer composites demonstrated in this work are attractive candidates as substrates for metamaterial absorbers for conformal applications. This paper approaches the problem of bandwidth enhancement of metamaterial absorbers by material engineering along with the resonant structure optimization leading to a synergetic effect in the properties of absorber.

Halide Anions Tuning of Lead-Free Perovskite-Type Ferroelectric Semiconductors with Inverse High-Temperature Symmetry Breaking.

There is a noticeable gap in the literature regarding research on halogen-substitution-regulated ferroelectric semiconductors featuring multiple phase transitions. Here, a new category of 1D perovskite ferroelectrics (DFP)2SbX5 (DFP+ = 3,3-difluoropyrrolidium, X- = I-, Br-, abbreviated as I-1 and Br-2) with twophase transitions (PTs) is reported. The first low-temperature PT is a mmmFmm2 ferroelectric PT, while the high-temperature PT is a counterintuitive inverse temperature symmetry-breaking PT. By the substitution of iodine with bromine, the Curie temperature (Tc) significantly increases from 348K of I-1 to 374K of Br-2. Their ferroelectricity and pyroelectricity are improved (Ps value from 1.3 to 4.0µCcm-2, pe value from 0.2 to 0.48µCcm-2K-1 for I-1 and Br-2), while their optical bandgaps increased from 2.1 to 2.7eV. A critical slowing down phenomenon is observed in the dielectric measurement of I-1 while Br-2 exhibits the ferroelastic domain. Structural and computational analyses elucidate that the order-disorder movement of cations and the distortion of the chain perovskite [SbX5]2- anions skeleton lead to PT. The semiconductor properties are determined by [SbX5]2- anions. The findings contribute to the development of ferroelectric semiconductors and materials with multiple PTs and provide materials for potential applications in the optoelectronic field.

Dielectric Behavior of Stretchable Silicone Rubber–Barium Titanate Composites

In this study, elastomer composites, including silicone rubber and barium titanate, were fabricated by mechanical mixing, a low-cost, fast, and easy technique to produce highly dielectric materials. The resulting composites were investigated in terms of their dielectric and mechanical properties in terms of filler percentage in the mixture. Dielectric permittivity measurements were taken using the microwave regime, and uniaxial tensile tests were carried out for the study of the materials’ mechanical properties, while combined experiments were also carried out to investigate potential correlations between them. The experimental results show that barium titanate inclusions in silicone matrix significantly improve the dielectric constant while reducing the mechanical properties of composites. In addition, combined experiments show that the composites exhibit a nearly stable dielectric profile under mechanical deformations. Consequently, mechanically mixed barium titanate–silicone elastomer composites could potentially become a cost-effective alternative in the extensive market for insulating materials and flexible electronics.

Effect of calcination temperature on structural, magnetic, and dielectric properties of Mg0.75Zn0.25Al0.2Fe1.8O4 ferrites

Based on the desire to improve material properties, the effects of temperature have begun to be investigated. It was found that for nano-sized powder materials, such as ferrites, the structural properties like crystal structure and grain size, as well as many magnetic and electrical properties depending on them, change with the calcination temperature. Considering these changes, the effect of calcination temperature on the structural, magnetic, and electrical properties of MZA ferrites (Mg0.75Zn0.25Al0.2Fe1.8O4) prepared by co-precipitation was investigated in this study. The produced MZA ferrites were calcined at three different temperatures (600, 700, and 800 °C). The X-ray diffraction results showed that the samples exhibited a cubic spinel structure. It was found that the crystal sizes (D_sch) calculated using the Debye-Scherrer equation increased with increasing calcination temperature (22.47, 33.53, and 42.53 nm). From the Williamson–Hall (W–H) plots, crystal sizes were calculated almost same as Debye–Scherrer crystal sizes. The nano-sized particles were examined by scanning electron microscope (SEM). Elemental analysis was performed using EDX. ν1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\ u }_{1}$$\\end{document} and ν2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\ u }_{2}$$\\end{document} absorption bands and O–H and C–H vibrations were detected in the FTIR spectra. Magnetic measurements were carried out at room temperature and in the range of ± 60 kOe under the applied field. Magnetic results are explained by superparamagnetism. Dielectric measurements were performed at room temperature and a frequency range of 20 Hz to 10 MHz. The dielectric properties can be explained by Maxwell–Wagner theory. Impedance spectroscopy study revealed that the relaxation mechanism is consistent with the Cole–Cole model. In AC conductivity studies at room temperature, it was found that the sample calcined at 600 °C would be suitable for energy storage devices.

Magnetoelectric CoV2O6—Role of Fe inter-play in Co-based Ising spin chain interactions

CoV2O6, a Brannerite-type material, exists in both monoclinic (α) and triclinic (γ) forms. α- CoV2O6 exhibits quasi-1D ferromagnetic chains of octahedrally-coordinated Co2+ions in the higher spin state. Fe2+ doped α-CoV2O6 (3 mol%) single crystals were synthesized using high temperature melt method. The motivation is to investigate whether disruption of 1D Co2+ ferromagnetic chains by small Fe3+ substitution alters the antiferromagnetic ground state and lead to stronger spin-frustration. In this paper, we report the magnetic and magnetodielectric properties of Fe doped α-CoV2O6 in detail. The strongly anisotropic nature of magnetic and magnetodielectric characteristics were captured well in the data through orientation dependent measurements with H being parallel to a and c axes of the crystal. Relative dielectric permittivity (εr) exhibited sharp peaks coinciding with the plateau edges Hc1 ∼2.2 T and Hc2 ∼4.4 T in the magnetization curves (M-H) for applied H parallel to a-axis. For dielectric measurements under applied H parallel to c-axis, relative dielectric permittivity exhibited sharp peak around Hc2 ∼3.1 T, again coinciding with the M-H behavior. Such closely related magnetic field induced dielectric transitions reflected in both M(H) and εr(H) measurements is a rare phenomenon and representative of strong spin-lattice coupling in this phase.

Structural, dielectric, and antimicrobial evaluation of PMMA/CeO2 for optoelectronic devices

In the current report, we have successfully synthesized nanocomposites of PMMA incorporating different doping of CeO2 through a chemical approach. XRD results reflects decent matching for CeO2 nanoparticles with 29 nm crystallite size. FTIR spectroscopy demonstrates the characteristic functional groups validating the successful formation of the composite. The optical study of PMMA and the nanocomposites has proven that the optical properties such as band gap, refractive index, optical permittivity, and loss tangent factor are affected by adding CeO2 to the PMMA matrix.The peak residing around 420 nm by UV measurements is allocated to occurring electrons photoexcitation from the valence to conduction band inherent in CeO2. The dielectric measurements were achieved using broadband dielectric spectroscopy upon a wide span of frequencies (10–1–107 Hz) and within temperatures from − 10 to 80 °C with a step of 10 °C. The permittivity decreases by adding CeO2 and the dielectric parameters are thermally enhanced, however, the temperature influence is based on CeO2 content, the higher the CeO2 amount, the higher the influence of temperature. The results of the nanocomposites revealed antibacterial activity counter to gram-positive bacteria strain (S. aureus, and B. subtilis), and gram-negative bacteria (E. coli, and K. pneumoniae), yeast (C. albicans, as well as fungi (A. niger). Inherently, the change in CeO2 concentration from 0.01 to 0.1 wt% delivers maximum influence against gram-negative bacteria. These PMMA CeO2-doped composites are beneficial for optoelectronic areas and devices.

Graphene-All-Around Cobalt Interconnect with a Back-End-of-Line Compatible Process.

The graphene-all-around (GAA) structure has been verified to grow directly at 380 °C using hot-wire chemical vapor deposition, within the thermal budget of the back end of the line (BEOL). The cobalt (Co) interconnects with the GAA structure have demonstrated a 10.8% increase in current density, a 27% reduction in resistance, and a 36 times longer electromigration lifetime. X-ray photoelectron spectroscopy and density functional theory calculations have revealed the presence of bonding between carbon and Co, which makes the Co atom more stable to resist external forces. The ability of graphene to act as a diffusion barrier in the GAA structure was confirmed through time-dependent dielectric breakdown measurement. The Co interconnect within the GAA structure exhibits enhanced electrical properties and reliability, which indicates compatibility applications as next-generation interconnect materials in CMOS BEOL.

Colloidal stability and dielectric behavior of eco-friendly synthesized zinc oxide nanostructures from Moringa seeds

This study centers on the environmentally benign synthesis of zinc oxide nanoparticles (ZnO NPs) derived from Zn (CH3COO)2·2H2O and Moringa seeds. The synthesized nanostructures underwent comprehensive characterization utilizing diverse analytical techniques, encompassing X-ray diffraction (XRD), UV–VIS spectroscopy, field-emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. XRD measurements coupled with W–H plot transformation unequivocally confirmed the formation of ZnO nanostructures, characterized by an average size of 24.9 nm. UV–VIS spectroscopy, complemented by Kubelka Munk curve analysis, elucidated the direct conduction and determined a bandgap of 3.265 eV. FESEM analysis revealed minimal particle aggregation, showcasing well-defined grain boundaries spanning sizes from 20.4 to 87.7 nm. XPS analysis substantiated the presence of Zn (2p), Zn (3p), Zn (3d), and O (1s). Raman spectroscopy identified E2H as the predominant mode, followed by E1(TO) and (E2H-E2L). ZnO thin films, fabricated via pulsed laser deposition (PLD) and deposited onto silicon (100) substrates, exhibited exemplary morphology and discernible topography, characterized by a normal grain size distribution. Zeta potential tests yielded a value of approximately (z\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\mathcalligra{z}$$\\end{document} ~ − 43.8 mV), indicative of the commendable stability of the colloidal suspension, likely attributable to low particle aggregation. Dielectric measurements conducted on sintered pellets at 900 °C unveiled elevated capacitance and dielectric constant at low frequencies across the temperature range of 289.935–310 K. These findings affirm the potential utility of environmentally synthesized ZnO for a spectrum of applications, including energy devices and nanofluids.

Structural and electrical characterization of Gd and Li modified Bismuth Sodium Strontium Titanate

Structural and electric characteristics of Gd, Li and Sr modified Bismuth Sodium Titanate i.e. (Bi0.5Na0.5)0.6(Gd0.5Li0.5)0.2Sr0.2TiO3 (BNGLST) composition is demonstrated. BNGLST was synthesized by the solid-state mixed oxide method using the stoichiometrically weighed constituent oxides and carbonates. The homogenously wet mixed powder was calcined at 1000 °C for 12h and compressed pellets were sintered at 1250 °C for 2h. X-ray diffraction was carried out to confirm the phase formation. Crystallographic information was extracted from the Rietveld refinement of the XRD data. Dielectric measurement was carried out from room temperature to 300 °C at 1 kHz − 1 MHz frequencies. The a.c. conductivity associated with oxygen ion conduction is discussed in detail as a function of temperature and frequency.