Diallyldimethylammonium Chloride Research Articles

Self-Healing, Electrically Conductive, Antibacterial, and Adhesive Eutectogel Containing Polymerizable Deep Eutectic Solvent for Human Motion Sensing and Wound Healing.

Flexible electronic devices such as wearable sensors are essential to advance human-machine interactions. Conductive eutectogels are promising for wearable sensors, despite their challenges in self-healing and adhesion properties. This study introduces a multifunctional eutectogel based on a novel polymerizable deep eutectic solvent (PDES) prepared by the incorporation of diallyldimethylammonium chloride (DADMAC) and glycerol in the presence of polycyclodextrin (PCD)/dopamine-grafted gelatin (Gel-DOP)/oxidized sodium alginate (OSA). The synthesized eutectogel has reversible Schiff-base bonds, hydrogen bonds, and host-guest interactions, which enable rapid self-healing upon network disruption. GPDO-15 eutectogel has significant tissue adhesion, high stretchability (419%), good ionic conductivity (0.79 mS·cm-1), and favorable antibacterial and self-healing properties. These eutectogels achieve 90% antibacterial effect, show excellent biocompatibility, and can be used as sensors to monitor human activities with strong stability and durability. The in vivo studies indicate that the eutectogels can improve the wound healing process which makes them an effective option for biological dressings.

Using Layer-by-layer Assembled Clay Composite Junctions to Enhance the Water Dissociation in Bipolar Membranes.

Bipolar membranes (BPMs) with a layer-by-layer (LbL) assembled montmorillonite (K30 MMT) clay-polyelectrolyte (PE) composite junction coated onto a sulfonated poly(ether ether ketone (SPEEK)) electrospun support are prepared, characterized and their water dissociation performance is analyzed. In particular, the focus is on the effect of the presence of the K30 MMT clay as a catalyst for water dissociation, the bilayer number (three, six, and nine), and the PE strength (poly(ethylenimine) (PEI) as a weak PE and poly(diallyl dimethylammonium chloride) (PDADMAC) as a strong PE) on the BPM performance. The BPMs are prepared by electrospinning and hot pressing SPEEK and the Fumion FAA-3 polymer. Adding the composite multilayers in the BPM junction decreases the membrane area resistance in reverse bias from 560 to 21 Ohms cm2 for the best-performing modified BPM. The bilayer number has limited influence on the overall membrane resistance, while the PDADMAC BPMs outperform the PEI BPMs due to the higher and more stable PE and clay adsorptions. Electrochemical impedance spectroscopy shows that the depletion layer thickness decreases exponentially with the number of bilayers as the water dissociation reaction becomes less dependent on the junction electric field. Furthermore, the higher Donnan exclusion at the modified junctions improves the BPM permselectivity 3-fold compared to the BPM containing no catalyst. Altogether, these improvements lead to 6.7 times less energy being used in BPM electrodialysis for the production of acid and base when a BPM with composite LBL junction is used compared to a BPM without catalyst. Thus, adding MMT clay composite LbL catalyst to BPM junctions is a promising method to improve the efficiency and reduce the energy consumption of electrochemical processes that rely on BPMs.

RuSiNPs@N,S-GQDs as self-enhanced anodic electrochemiluminescent immunobeacons for the highly sensitive quantitation of okadaic acid in shellfish.

Acompetitive electrochemiluminescence (ECL) immunosensor isproposed to accurately and rapidly assess okadaic acid (OA) levels in shellfish using a novel self-reinforced solid-state ECL marker, which is essential for ensuring seafood safety. Graphene quantum dots doped with nitrogen and sulfur (N,S-GQDs) were synthesized, for the first time, through the electrolysis of graphite in 3-(N-morpholine) propane sulfonic acid solution. Intriguingly, these N,S-GQDs exhibited exceptional co-reactant properties, significantly enhancing the anodic ECL performance of Ru(bpy)32+ in a phosphate-buffered saline solution. Following the functionalization of Ru(bpy)32+-doped silica nanoparticles (RuSiNPs) with poly(diallyldimethylammonium) chloride, we achieved a well-dispersed assembly of N,S-GQDs on the exterior of the RuSiNPs through electrostatic interactions. Importantly, the core-shell structure of RuSiNPs@N,S-GQDs efficiently encapsulated both the luminophore and co-reactant, thus improving the transfer rates of electrons, shorting interaction distances, and reducing energy loss during light emission. Leveraging this "bright" ECL beacon, theECL immunosensor demonstrated remarkable analytical performance, yielding a low half maximal inhibitory concentration (IC50) of 0.14ngmL-1, an extensive linear range spanning 0.003-40ngmL-1, and impressively low limit of detection of 0.001ngmL-1 for OA determination.

Polyelectrolyte film based on pectin and poly(diallyldimethylammonium chloride) with antioxidant and antimicrobial activity

Polyelectrolyte film based on pectin and poly(diallyldimethylammonium chloride) with antioxidant and antimicrobial activity

Antifungal Associations with a Polyelectrolyte Promote Significant Reduction of Minimum Inhibitory Concentrations against Opportunistic Candida spp. Strains.

The current global scenario presents us with a growing increase in infections caused by fungi, referred to by specialists in the field as a "silent epidemic", aggravated by the limited pharmacological arsenal and increasing resistance to this therapy. For this reason, drug repositioning and therapeutic compound combinations are promising strategies to mitigate this serious problem. In this context, this study investigates the antifungal activity of the non-toxic, low-cost and widely available cationic polyelectrolyte Poly(diallyldimethylammonium chloride) (PDDA), in combination with different antifungal drugs: systemic (amphotericin B, AMB), topical (clioquinol, CLIO) and oral (nitroxoline, NTX). For each combination, different drug:PDDA ratios were tested and, through the broth microdilution technique, the minimum inhibitory concentration (MIC) of these drugs in the different ratios against clinically important Candida species strains was determined. Overall, PDDA combinations with the studied drugs demonstrated a significant increase in drug activity against most strains, reaching MIC reductions of up to 512 fold for the fluconazole resistant Candida krusei (Pichia kudriavzevii). In particular, the AMB-PDDA combination 1:99 was highly effective against AMB-resistant strains, demonstrating the excellent profile of PDDA as an adjuvant/association in novel antifungal formulations with outdated conventional drugs.

Arsenic(V) removal from water using polyelectrolyte enhanced ultrafiltration with poly(dimethyldiallylammonium chloride) (PDADMAC): Ion-selectivity based modeling and electric field influence

Polyelectrolyte enhanced ultrafiltration (PEUF) shows promise for arsenic removal. However, competing ions may serve as potential limiting factors, and membrane fouling caused by aggregation of polyelectrolytes may impact PEUF performance. This study employed poly(dimethyldiallylammonium chloride) (PDADMAC) for arsenate (As(V)) removal via ultrafiltration, and the electric field assistance was investigated on the PEUF performance. Ion exchange experiments between Cl-, and typical anions were conducted in a binary system to determine the selectivity coefficients (Ksel) of PDADMAC for different anions. The affinity of PDADMAC towards common monovalent anions was found to be Br->NO3->Cl->H2PO4->HCO3->H2AsO4-, while its affinity for divalent anions decreased in the order SO42-> HPO42-> HAsO42-. By determining the selectivity coefficients of various anions with PDADMAC and utilizing mass conservation models, a phase distribution model for anions during PEUF process was developed to predict As(V) removal. Predictions were made regarding the enhanced ultrafiltration efficiency for As(V) under different conditions (pH, ionic strength, and competing anions) in complex water environments. As the dosage of PDADMAC increased, the removal of As(V) from the actual water sample spiked with an initial concentration of 0.2mM exceeded 90%, and the experimental results closely matched the model predictions. The impact of electric field on the PEUF process was investigated by placing electrodes on both sides of the ultrafiltration membrane. Results showed that the ultrafiltration membrane, when positively charged by an electric field, repelled cationic PDADMAC, thereby alleviating membrane fouling. However, a cleaner membrane led to increased leakage of PDADMAC molecules, resulting in the co-loss of As with PDADMAC and consequently reducing the overall As removal.

Heterogeneous Covalent Organic Framework Membranes Mediated by Polycations for Efficient Ions Separation.

Precise ions sieving at angstrom-scale is gaining tremendous attention thanks to its significant impact at the water-energy nexus. Herein, a novel polycation-modulated interfacial polymerization (IP) strategy is developed to prepare a heterogeneously charged covalent organic frameworks (COFs) membrane. Cationic poly(diallyldimethylammonium chloride) (PDDA) regulates the growth and assembly of anionic COFs nanosheets, which thus provides a negative, smooth top surface and positive, rough bottom surface, indicating the presence of heterogeneously charged angstrom-scale channels through the membrane. Experiments and simulations are conducted to understand the facilitated ions transport behavior relative to specific interactions raised by heterogeneously charged channels and angstrom-scale steric hinderance as well, rendering the membrane with robust mono-/divalent cations sieving capabilities. The selectivity (61.6) of Li+ to Mg2+ in mixed saline under the continuous cross-flow filtration mode is superior to most of the reported nanofiltration membranes. This polycation-mediated interfacial polymerization strategy offers a compelling opportunity to develop versatile heterogeneously charged COF membranes for exquisite ion sieving.

Selective separation of dyes and tetracycline hydrochloride in polymer‐nucleotide coacervate droplets

AbstractThis paper reports the formation of coacervates by the electrostatic interaction of poly (diallyldimethylammonium chloride) (PDDA) and adenosine triphosphate (ATP) in aqueous solution, examining its formation conditions, stability, and efficiency in separation. The ideal concentration for creating coacervate droplets in pure water, HEPES buffer, and NaCl solution was determined to be 20 mM of PDDA and ATP. Enhancing the stability of coacervates was achieved by incorporating phospholipid vesicles on their surface, presenting a novel strategy for building cell models. Ostwald Ripening was employed to comprehend the growth mechanism of the coacervates, while the Hofmeister Ion Series and Schulze‐Hardy's rule were utilized to elucidate the stability differences in solutions containing NaCl, Na2SO4, and MgCl2. These coacervates were stable at concentrations below 90 mM NaCl, 200 mM Na2SO4, and 30 mM MgCl2, respectively. We also explored the specific separation of dyes and tetracycline hydrochloride (TC) in the coacervates. Separation efficiencies of 92.98% for methylene blue (MB), 94.19% for methyl orange (MO), and 85.94% for TC, were achieved by the coacervates, which can be attributed to the synergistic effects of hydrophobicity, electrostatic forces, and π‐π interactions. The proposed coacervates have great potential in cell mimicry and water treatment.

A facile method for carbon nanotube/carbon fiber‐reinforced polylactic acid composites

AbstractThe mechanical strength of polylactic acid (PLA) can be improved by carbon fiber (CF) compositing to expand its application in tissue engineering scaffolds. However, the mechanical strength of CF‐reinforced polylactic acid (CFRPLA) composites is compromised due to weak interfacial interaction resulting from the chemically inert surface of CF. In the article, carbon nanotube (CNT) with poly(diallyldimethylammonium chloride) (PDDA) as a coupling agent was covered on CF to improve the chemical activity and roughness of the surface of CF, and then the as‐prepared CF‐PCNT were further incorporated into PLA via melt compounding. The yield strength, modulus, and thermal conductivity of PLA/CF‐PCNT were 14.09%, 7.65%, and 5.24% higher than those of PLA/CF, respectively, and the volume resistivity was 99.74% lower at a 10 wt% loading. The enhancement for the mechanical properties of PLA/CF‐PCNT composites could be ascribed to the mechanical locking, hydrogen bonds and covalent bonds between CF and matrix through the interface modulation of CNT and PDDA. This facile and non‐destructive method offers a novel strategy for the modification of CF fillers.Highlights CF was modified by PDDA and CNT through a facile and non‐destructive method. The active functional groups and roughness on the surface of CF were increased. The surfaces of CFs were characterized by FT‐IR, Raman spectra, XPS and SEM. The interface was improved by mechanical locking, covalent, and hydrogen bonds. The mechanical strength, electrical and thermal conductivity of composites were improved.

Synthesis and Evaluation of High-Temperature Resistant Polymer Plugging Agent for Water-Based Drilling Fluids.

As the exploration and development of deep wells have emerged as a key option to extract more oil and gas resources trapped underneath, high-temperature formations impose stringent requirements on the thermal stability of plugging agents used in water-based drilling fluids. In this work, β-cyclodextrin, with its unique conical toroidal rigid stable structure and internal hydrophobic and external hydrophilic special adsorption capacity, was first grafted with maleic anhydride to prepare a silicone polymer and then copolymerized with dimethyldiallylammonium chloride (DMDAAC) in the presence of coupling agent vinyltriethoxysilane (A151) and cross-linking divinylbenzene (DVD) to finally obtain a high-temperature resistant plugging agent (AMMD). Subsequently, the molecular structure was evidenced and the performance of AMMD was examined in the polysulfonate-base fluid via a series of tests including high-temperature high-pressure filtration loss, sand tray plugging, and drilling fluid displacement, and the results were compared with the counterpart Soltex under the same conditions. The optimal synthesis conditions for the plugging agent were found as total monomer concentration of 25%, initiator mass fraction of 1% (based on the mass of monomers), monomer feed ratio of m (DVD):m(A151):m(DMDAAC):m(MD) of 15:3:2:15, pH value of 10, reaction temperature of 75 °C, and reaction time of 4 h. FT-IR spectra indicated that the monomers used to prepare AMMD were successfully involved in the reaction for the design of the plugging agent structure. TGA showed that AMMD has a total weight loss of about 35.98% in the range of 284 to 453 °C. Moreover, the addition of 3%AMMD into the base fluid produced a 4.38-fold and 3.8-fold filtration loss control over 60 min at 200 °C using 400 and 800 mD sand trays, respectively, which were comparatively higher than the commercially available Soltex (ca. 3.72-fold and 3.14-fold, respectively, using 400 and 800 mD). This then contributed to AMMD's superior plugging performance in drilling fluid based on the drilling fluid displacement experiment, implying that AMMD could find potential use as a plugging agent in polysulfonate drilling fluid under severe geothermal conditions.

Preparation of grafted starch‐based cationic flocculants and its removal of reactive and disperse dyes

AbstractIn this paper, a starch‐based flocculant (ADSt) with medium and low temperature solubility and enhanced flocculation effect was synthesized using corn starch, acrylamide, and dimethyldiallyl ammonium chloride as main materials by the ethanol‐alkali method and grafting method. The main mechanism of ADSt's flocculation was electrical neutralization and bridging. The flocculation performance of ADSt was verified by using it along with polymeric aluminum chloride (PAC) as coagulant/flocculant, dispersible dye (dispersible yellow RGFL), and reactive dye (active trimeric blue KN‐G) to simulate dye wastewater. For the dispersed yellow water sample and active emerald blue water sample, the dosage of PAC was 40 and 35 mg/L respectively. When the dosage of ADSt was 10 mg/L with a dye content of 100 mg/L, the decolorization rates for both dyes reached up to 96.2% and 94.4% respectively. The properties of the flocs such as size and two‐dimensional fractal structure were described. The prepared ADSt maintained a good flocculation effect in the pH range of 5–9 due to its excellent water solubility achieved through the ethanol‐alkali preparation process, where its solubility reached 86.7% at 30°C. Overall, the preparation process for ADSt is simple, cost‐effective, while providing an effective solution for treating printing and dyeing wastewater.

Purification Processes for Generating Cationic Lignin-Acrylamide Polymers.

Purification is an essential step in many polymerization processes for fabricating highly pure polymers. This study considered various purification methods for purifying the product of lignin, acrylamide (AM), and diallyl dimethylammonium chloride (DADMAC) copolymerization reactions at a laboratory scale. The charge density, yield, molecular weight, and solubility analyses confirmed that ethanol extraction and membrane filtration were the most effective processes for producing lignin-p(AM)-p(DADMAC). The 1H NMR analysis revealed that the membrane dialysis effectively removed unreacted AM and DADMAC monomers from the reaction medium. The produced samples of the ethanol-extraction and dialysis processes had higher solubility and yield compared to the product of the acidification process. Thermogravimetric studies confirmed that the ethanol-extracted and dialyzed samples had a degradation temperature (220 °C) higher than that of the acidified samples (160 °C). The rheological studies confirmed that the viscosities of the polymer solutions were influenced more by the solubility than by the molecular weight of the generated polymers within the molecular weight range examined in this study. The flocculation studies confirmed that the ethanol-extracted and dialyzed polymers were more effective flocculants than the acidified samples for the particles of a kaolinite suspension. Based on the above results, membrane filtration with a larger pore size could be an environmentally friendly method for effectively purifying lignin-p(AM)-p(DADMAC).

Dual signal amplification strategy-based electrochemical aptasensor utilizing redox molecule/MOF composites for multi-pesticide detection

Electrochemical aptasensor is a great tool for simultaneously assessing harmful pesticide residues in agricultural products and foods. This study ingeniously designed an electrochemical aptasensor based on dual signal amplification strategies for concurrent detection of various pesticide residues. Firstly, poly(diallyldimethylammonium chloride)-functionalized reduced graphene oxide (PR) and Au-Pt-Pd trimetallic nanoflowers supported on HP-UiO66-NH2 were creatively employed together as substrates to load more aptamers, ascribed to the improved conductivity, abundant sites and a large electrochemical effective surface area. Secondly, ferrocene-cysteine gold nanoparticles supported on CeMOF(Ⅲ, Ⅳ) and methylene blue-loaded MOF235 were innovatively engineered to build two distinctive signal labels, which displayed comparable large and stable signal currents among other redox molecule/MOF composites. Additionally, PR contributed further signal amplification. Consequently, the constructed aptasensor showed superior performance for simultaneous detection of acetamiprid (AD) and malathion (ML), with linear ranges from 10 pM to 0.1 μM and detection limits of 4.8 pM for AD and 0.51 pM for ML. Moreover, the aptasensor performed well in the assay of AD and ML in Chinese cabbage samples with high accuracy compared with a high-performance liquid chromatography-tandem mass spectrometry method. Overall, the strategies proposed herein provided a useful and potential route for general development of electrochemical aptasensors to simultaneously detect multiple pesticide residues.

A cationic polyelectrolyte for enhancing dewatering of montmorillonite-containing coal slime: adsorption and modification mechanism

ABSTRACT In this study, a cationic polyelectrolyte (Poly dimethyl diallyl ammonium chloride, PDADMAC) was introduced as a filter aid to enhance the dewatering effect of montmorillonite (MT)-containing coal slime, and compared with cationic polyacrylamide (CPAM). The dewatering performance of PDADMAC and CPAM was evaluated based on vacuum filtration experiments. The modification mechanism of PDADMAC on Mt particle surface was revealed by filter cake pore distribution, zeta potential, contact angle and Atomic Force Microscopy (AFM). The adsorption difference between PDADMAC and CPAM on Mt surface was studied by Density Functional Theory (DFT). In addition, DLVO theory further explains the mechanism of PDADMAC enhancing dewatering from the perspective of interaction force. The optimal dosage of PDADMAC was 125 g/t, and the filter cake moisture content was reduced by 3%. Compared to CPAM, PDADMAC achieves efficient dewatering at a lower dosage. PDADMAC has a more prominent ability to neutralize charge, and its effect on interparticle interactions was a potential mechanism to promote dehydration.

Polymerizable deep eutectic solvent enables flexible gel formation for motion sensor and anti-UV film

Specific applications of gels can raise multiple demands, including low cost, elasticity, adaptability to wide temperature ranges, conductivity, and reduced hazards, thereby presenting diverse challenges for one material. Deep eutectic solvents (DESs) offer unexpected solutions to tackling the challenging task. Here, we mixed anhydrous diallyldimethylammonium chloride (DMDAAC) and urea to synthesize a polymerizable DES with a wide range of solubility. It can polymerize to form versatile DES gel upon photoinitiation. The gel exhibited high transparency (∼94 %), a wide range of temperature tolerance (−40 ∼ 100 °C), outstanding elastic properties (ε > 2400 %), good conductivity (0.05 mS·cm−1) and self-healing capability. The pristine gel film was successfully applied to motion sensors, while the DES gel with lignin was also employed as an elastic anti-UV film. Moreover, its water-solubility and non-hazardous compositions suggest the minimize environmental impact of the DES gel. This polymerizable DES can not only boost the development of electronic devices like motion sensors, but also inspire more creative ideas in promising applications of DESs and DES gels.

Synergistic enhancement of dewatering of montmorillonite-containing coal slime by novel combined filter aid: an experimental and simulation study

ABSTRACT The efficient dewatering of montmorillonite (Mt)-containing coal slime is still an urgent problem to be solved in coal preparation plant. In this study, the dewatering effect of poly(o-phenylenediamine)/Poly dimethyl diallyl ammonium chloride (POPD/PDADMAC) combined filter aid on Mt-containing coal slime was studied. The dewatering performance of combined filter aid was investigated by vacuum filtration test. The action mechanism of combined filter aid was revealed by contact angle, zeta potential, cake pore and atomic force microscope (AFM). The co-adsorption principle of the combined filter aid was elucidated based on density functional theory (DFT) and molecular dynamics simulation (MD). Compared to PDADMAC, the combined filter aid has better performance for dewatering of Mt-containing coal slime, and has the advantage of low reagent dosage. The combined filter aid can greatly reduce the Mt potential, increase the Mt contact angle, and increase the porosity of the filter cake. There was a co-adsorption effect between the combined filter aid. Specifically, there were ion–dipole interaction, cation–π interaction and Cl ions bridged electrostatic interaction between POPD and PDADMAC. This study has developed a novel combined filter aid, which provides theoretical and technical support for the high-efficiency pressure filtration dewatering of Mt-containing coal slime in coal preparation plants.

Self-assembled conductive coating and bifacial microstructures Collaboratively Adjusting the sensing performance and high reliability of the flexible pressure sensors

Flexible pressure sensors are being studied intensively for applications such as smart wearables and health monitoring. While ensuring the excellent sensing performance, the reliability (durability and environmental resistance) of the sensors are also key indicators that determine whether they can be used in practice. In this research, a strategy to adjust the sensing performance and high reliability of the flexible pressure sensors by self-assembled conductive coating and bifacial microstructures (BM) is proposed. Polydimethylsiloxane/carbon nanotube films with BM are first modified to reduce the surface contact angle. Then poly(dimethyl diallyl ammonium chloride) (PDAC) and hydroxylated carbon nanotubes/carboxylated cellulose nanofibers/glycerol (CNT-OH/CNF-C/GL) are successively assembled on the BM surface to construct conductive coatings (PCCG). The sensor based on PCCG and BM (the PCCG-BM sensor) shows a high sensitivity (9.97 kPa−1), a wide detection range (0–330 kPa), and a fast response time (59 ms). The PCCG-BM sensor has excellent repeatability, and it still outputs stable current change signals after 240,000 pressure cycles. What’s more, the PCCG-BM sensor is treated with extreme environments such as bending, stretching, washing, and high pressure, and the sensor still maintains excellent performances. This preparation strategy provides a new perspective for the fabrication of high-performance and high-reliability flexible sensors.

Exploring the dyeing potential of annatto dye on linen substrate: An inquiry into the effects of different mordants

AbstractThis study aimed to compare the dyeing capacity of annatto dye on linen textile substrates under the influence of different mordants, such as ferrous sulphate, alum, chitosan, and poly(diallyldimethylammonium chloride) (PDDACl). Annatto dye was extracted in an alcoholic medium, and the concentrations of the dye compounds bixin and norbixin were determined using ultraviolet‐visible spectrophotometry. Dyeing experiments were conducted with 10% and 20% weight of material (s.p.m.) concentrations, both on mordant‐treated substrates and on substrates pre‐bleached only. The colour evaluation indicated better colour yields for substrates pretreated with alum and PDDACl, with colour strength (K/S) values of 41.14 and 38.74, respectively, for dyeing with 20% s.p.m. However, these substrates exhibited the highest colour deviation (∆E) values in washing and lightfastness tests. The substrate pretreated with ferrous sulphate and the substrate pre‐bleached only showed K/S values of 25.99 and 18.68, respectively, with the ferrous sulphate‐treated substrate exhibiting the lowest ∆E values in washing and lightfastness tests among all evaluated substrates. Chitosan‐cationised samples showed the lowest colour yield, with a K/S of 12.51. Regarding washing and lightfastness, the pre‐bleached only substrate and the chitosan‐pretreated substrate displayed intermediate ∆𝐸 values. The dyeing kinetics of pre‐bleached substrates exhibited pseudo‐first‐order behaviour, while for ferrous sulphate‐pretreated samples, pseudo‐second‐order behaviour was observed. Langmuir's adsorption model was suitable for pre‐bleached substrate dyeing and ferrous sulphate‐pretreated sample dyeing in adsorption isotherms. However, for mordanted samples, higher adsorption intensity was observed.

Polyelectrolyte modified Ag-nanosphere: A Practical Approach for Sensitive and Selective SERS-based Detection of Organic Dye Pollutants

This study presents a cost-effective method for fabricating surface-enhanced Raman spectroscopy (SERS) substrates using Ag-nanospheres (AgNS) capped with Poly(diallyldimethylammonium chloride) (PDADMAC) and poly(styrene sulfonate) (PSS). AgNS synthesis involves immersing Ag-nanocrystals in a nonaqueous solution, mixed with PEs in an aqueous solution via ultrasonic disturbance. Resulting aggregates form stable spherical assemblies with diameters ranging from 150 nm to 450 nm, and various characterization techniques, including scanning electron microscopy with energy-dispersive X-ray, UV-visible spectrophotometry, dynamic light scattering, and zeta potential analysis, were employed to analyze their fundamental chemical and physical properties. These qualified AgNSs serve as SERS substrates for sensitive and selective identification of charged organic dye contaminants, such as rhodamine 6G (R6G) and rose bengal (RB). Sensitivity assessments with the optimized quantities of either PDADMAC or PSS-capped AgNSs demonstrate successful detection down to concentrations of 10-14 M for RB and 4 x 10-13 M for R6G. The same SERS substrates also enable electrostatically driven selective detection even in analyte mixtures, and an additional variation of the SERS substrate comprising a complex of PDADMAC-capped and PSS-capped AgNSs exhibited distinct SERS spectra influenced by both positively and negatively charged analytes. Finally, successful detection of two oppositely charged pesticides was achieved through electrostatic attraction, so theses polyelectrolytes capped AgNS-based SERS substrate presents a promising avenue for efficiently and selectively detecting charged organic contaminants.

Insight into the corrosion inhibition performance of dimethyldiallylammonium chloride acrylamide copolymer for mild steel in acidic solution

Dimethyldiallylammonium chloride acrylamide (DADMAC-AAM) copolymer was firstly applied as a novel corrosion inhibitor for carbon steel in acidic solution. Electrochemical, theoretical and computational methods were performed to illustrate the corrosion inhibition mechanism of DADMAC-AAM. Results of electrochemical tests indicated that DADMAC-AAM effectively slowed down corrosion rate of mild steel in HCl solution as a mixed-type corrosion inhibitor. Its corrosion inhibition efficiency increased with dosage, and the maximum value reached about 92.44 % with adding 100 mg/L. In-situ scanning vibration electrode technique illustrated that the corrosion inhibition performance of DADMAC-AAM increased with immersion time. Metal surface was covered with a dense hydrophobic film due to the physical-chemical adsorption of DADMAC-AAM molecules, and the adsorption behavior obeyed to the Langmuir adsorption isothermal model. Theoretical calculations were carried out to explain the corrosion inhibition mechanism, and the increase of active energy indicated that the strong inhibitive action of DADMAC-AAM molecule could be due to the increase of activation energy barrier of corrosion reaction. Results obtained from computational simulations proved that DMDMAC-AAM molecules adsorbed on metal surface through interactions between N or O and Fe atoms. This adsorption film could retard the invasion of corrosive species, thus protecting metal from corrosion.