Mission Design Research Articles

3Cat-8 Mission: A 6-Unit CubeSat for Ionospheric Multisensing and Technology Demonstration Test-Bed

This paper presents the mission analysis of 3Cat-8, a 6-Unit CubeSat mission being developed by the UPC NanoSat Lab for ionospheric research. The primary objective of the mission is to monitor the ionospheric scintillation of the aurora, and to perform several technological demonstrations. The satellite incorporates several novel systems, including a deployable Fresnel Zone Plate Antenna (FZPA), an integrated PocketQube deployer, a dual-receiver GNSS board for radio occultation and reflectometry experiments, and a polarimetric multi-spectral imager for auroral emission observations. The mission design, the suite of payloads, and the concept of operations are described in detail. This paper discusses the current development status of 3Cat-8, with several subsystems already developed and others in the final design phase. It is expected that the data gathered by 3Cat-8 will contribute to a better understanding of ionospheric effects on radio wave propagation and demonstrate the feasibility of compact remote sensors in a CubeSat platform.

Mission Design and Validation of a Fixed-Wing Unmanned Aerial Vehicle for Environmental Monitoring

Climate change is becoming a worldwide emergency. In order to prevent catastrophic levels of climate change, three broad categories of action are ongoing: cutting emissions, adapting to climate impacts, and financing required adjustments. Cutting emissions requires stopping the use of fossil fuels in favor of renewable energy sources. Adapting to climate change and financing required adjustments need instruments for the understanding of the source causes and how effective the potential measures are. In this context, the use of Unmanned Aerial Vehicles for environmental monitoring is continuously increasing thanks to their ability to collect a wide range of environmental data, from the quality of air to the health status of vegetation, waters, and lands. This paper describes the research activities that are being performed for the design and development of a 100 kg Max Take Off Mass prototype zero-emission Unmanned Aerial Vehicle, named Daphne, destined for environmental monitoring, surveillance, and inspection missions. The developed prototype will drive the next industrialization of the vehicle. A particular focus is given to the design of the power system, based on the use of Proton Exchange Membrane fuel cells fueled with green hydrogen, the integration of the sensors allowing for multipurpose observations and measurements, and the design and validation of the relative multi-purpose missions via an innovative approach based on Model-Based System Engineering.

Database of Candidate Targets for the LIFE Mission

We present the database of potential targets for the Large Interferometer For Exoplanets (LIFE), a space-based mid-infrared nulling interferometer mission proposed for the Voyage 2050 science program of the European Space Agency. The database features stars, their planets and disks, main astrophysical parameters, and ancillary observations. It allows users to create target lists based on various criteria to predict, for instance, exoplanet detection yields for the LIFE mission. As such, it enables mission design trade-offs, provides context for the analysis of data obtained by LIFE, and flags critical missing data. Work on the database is in progress, but given its relevance to LIFE and other space missions, including the Habitable Worlds Observatory, we present its main features here. A preliminary version of the LIFE database is publicly available on the German Astrophysical Virtual Observatory.

Radiation exposure of astronauts following an intense solar particle event: analysis and comparison of doses in male and female voxel phantoms.

According to NASA's plans, a human travel to the Moon is planned by the end of 2025 with the Artemis II mission, and humans should land on the Moon again in 2026. Exposure to space radiation is one of the main risks for the crew members; while for these short missions the doses from galactic cosmic rays would be relatively low, the possible occurrence of an intense solar particle event (SPE) represents a major concern, especially considering that in 2025 the Sun activity will be at its peak. Quantifying the amount and the effects of such exposure is therefore crucial, to identify shielding conditions that allow respecting the dose limits established by the various space agencies. By exploiting an interface between the BIANCA biophysical model and the FLUKA Monte Carlo radiation transport code, in this work we implemented a male and a female voxel phantom and we calculated absorbed doses and Gy-Eq doses in the various tissues/organs, as well as effective doses, following exposure to the August 1972 SPE, the most intense event of the modern era. The calculations were performed respect the organ dose limits for 30 d missions. A detailed comparison between male and female doses was then carried out, also considering that the Artemis II crew will include a woman. The results showed that female doses tend to be higher than male doses, especially with light shielding. This should be taken into account in mission design, also considering that, in a typical lunar mission, up to 15% of time may be spent in extra-vehicular activities, and thus with light shielding. More generally, this work outlines the importance of performing separate calculations for male and female astronauts when dealing with radiation doses and effects.

Investigating Subsurface Properties of the Shallow Lunar Crust Using Seismic Interferometry on Synthetic and Recorded Data

AbstractIn the past few years, the remarkable progress of commercially operated spacecrafts, the success with reusable rocket engines, as well as the international competition to explore space, has led to a substantial acceleration of activities in the design and preparation of ambitious future lunar missions. In the search for ice and/or cavities imaging the shallow subsurface structure is of vital importance. Hereby, previous studies have shown that seismic interferometry is a promising method to investigate the subsurface properties from passive lunar data. In this study, we want to evaluate the potential of this method further by examining the required duration of seismic measurements and the influence of scattering on the Green's function retrieval. Therefore, we applied seismic interferometry to both measured Apollo 17 data and synthetic data. Our findings indicate that, under optimal conditions, a few hours of data are sufficient when using the method of time‐scaled phase‐weighted stack (ts‐PWS). However, this strongly depends on the inter‐station distance, the orientation toward the principal noise sources, and the timing of the measurement during the lunar cycle. Additionally, we were able to reproduce the measured data using numerical simulations in 2D. The synthetic results show that scattering effects clearly influence the Green's function extraction, especially for larger station distances.

Stable configuration design for libration point gravitational wave observatory

The Sun-Earth L2 libration point configuration is one of the options for space-based gravitational wave detection. Long-term configuration stability is crucial for high-precision measurements, challenged by the strong nonlinear dynamics of the Sun-Earth three-body system. This paper proposes an efficient design method and determines the feasible parameter domain for the libration point gravitational wave observatory. First, the dynamic model for the libration point configuration is established, and the stability indexes are defined. The sensitive parameters that affect the relative geometric configuration are discussed and the phase angle is found to be the key factor. Then, an efficient design method is proposed, and the procedure is divided into two steps. The phase angle of the Earth phase offset orbit and the libration point configuration are optimized successively. Finally, the proposed method is applied to the LAGRANGE mission concept. The results show that the three stability indexes decrease by 59%, 42% and 23%, respectively. Moreover, a mapping between configuration parameters and stability indexes is established. The feasible parameter domain for the stable libration point configuration is discussed. The feasible amplitudes domain in the x and z directions of the libration point orbit should be less than 6200 km and 42000 km, respectively, to guarantee configuration stability. This research could provide a reference for the stable design and implementation of gravitational wave detection missions utilizing libration point configuration in the future.

Quantifying Uncertainty in Atmospheric Winds Retrieved from Optical Flow: Dependence on Weather Regime

Abstract This study explores the performance of a dense optical flow method in comparison to pattern-matching techniques for retrieving atmospheric motion vectors (AMVs) from water vapor images. Using high-resolution simulated datasets that represent various weather phenomena, we assess the performance of these methods across different weather regimes, time intervals, and pressure levels and quantify the uncertainties associated with retrieved winds. The optical flow algorithm consistently outperforms the feature matching approach. Notably, it produces wind speeds and AMVs that closely resemble the wind fields from the simulations, and unlike the feature matching algorithm, the optical flow algorithm exhibits consistent performance across different time intervals. In contrast, the feature matching approach yields vector fields that exhibit oversmoothing in certain areas and erratic behavior in others, while also producing less detailed, regionally constant speed maps. Furthermore, unlike feature matching, the optical flow method effectively calculates AMV near regions with missing data, generating a dense AMV field for every pixel in a pair of images. This superior performance and flexibility significantly influence the planning for future satellite missions aimed at retrieving atmospheric winds. As such, our work plays a critical role in determining the mission architecture and projected instrument performance for future atmospheric wind retrieval satellite missions. The study underscores the potential of the optical flow algorithm as a robust and efficient approach for atmospheric motion retrieval, thus contributing to advances in climate research and weather prediction. Significance Statement This research investigates the efficacy of two methods, optical flow and feature matching, for detecting atmospheric winds, referred to as atmospheric motion vectors, from satellite images of water vapor. Employing detailed simulated datasets that replicate real-world weather patterns, we found that optical flow consistently outperforms feature matching in various aspects. Notably, the optical flow method is not only more precise but also maintains its accuracy across different scenarios. These insights are critical for the design of future satellite missions focused on advancing our understanding of the atmosphere and enhancing weather predictions. This study contributes to advancements in climate research and supports improved weather forecasting, benefiting both scientific and societal needs.

MAUVE: An Ultraviolet Astrophysics Probe Mission Concept

We present the mission concept “Mission to Analyze the UltraViolet universE” (MAUVE), a wide-field spectrometer and imager conceived during the inaugural NASA Astrophysics Mission Design School. MAUVE responds to the 2023 Announcement of Opportunity for Probe-class missions, with a budget cap of $1 billion, and would hypothetically launch in 2031. However, the formulation of MAUVE was an educational exercise and the mission is not being developed further. The Principle Investigator-led science of MAUVE aligns with the priorities outlined in the 2020 Astrophysics Decadal Survey, enabling new characterizations of exoplanet atmospheres, the early-time light curves of some of the universe’s most explosive transients, and the poorly-understood extragalactic background light. Because the Principle Investigator science occupies 30% of the observing time available during the mission’s 5 yr lifespan, we provide an observing plan that would allow for 70% of the observing time to be used for General Observer programs, with community-solicited proposals. The onboard detector (THISTLE) claims significant heritage from the Space Telescope Imaging Spectrograph on Hubble, but extends its wavelength range down to the extreme UV. We note that MAUVE would be the first satellite in decades with the ability to access this regime of the electromagnetic spectrum. MAUVE has a field of view of 900″ × 900″, a photometric sensitivity extending to m UV ≤ 24, and a resolving power of R ∼ 1000. This paper provides full science and mission traceability matrices for this concept, and also outlines cost and scheduling timelines aimed at enabling a within-budget mission and an on-time launch.

Spacecraft formation flying orbital control for earth observation mission

Synthetic Aperture Radar (SAR) sensors have gained much attention for multiple civil use cases, where NewSpace startups have launched and planning to launch sensors to orbit to harvest the unique capabilities of SAR for the Earth Observation (EO) market. Unlike optical, SAR can capture images in all lighting conditions and penetrate cloud cover, generating exceptional use cases, which makes SAR the most reliable sensor. For example, monitoring soil deformation with millimeter accuracy, oil spills, crop lodging, and typical EO use cases of optical sensors that are unable to penetrate the clouds or see at night. However, SAR is still limited in civil use cases because it is tough to interpret. In addition, unlike government users who can consume the SAR data directly, most civil end-users need analytics on top of the data. To unlock the potential civil use cases, many experts believe that optical EO data should be fused with SAR at the EO upstream, thus suggesting optical and SAR sensors fly in formation. Spacecraft Formation Flying (SFF) is one of the key technology enablers for space exploration and EO space missions. This paper presents an SFF EO mission (SAR and Optical) design considering orbit requirements to maximize user objectives inspired by OptiSAR™ Constellation.

Space radiation measurements during the Artemis I lunar mission

Space radiation is a notable hazard for long-duration human spaceflight1. Associated risks include cancer, cataracts, degenerative diseases2 and tissue reactions from large, acute exposures3. Space radiation originates from diverse sources, including galactic cosmic rays4, trapped-particle (Van Allen) belts5 and solar-particle events6. Previous radiation data are from the International Space Station and the Space Shuttle in low-Earth orbit protected by heavy shielding and Earth’s magnetic field7,8 and lightly shielded interplanetary robotic probes such as Mars Science Laboratory and Lunar Reconnaissance Orbiter9,10. Limited data from the Apollo missions11–13 and ground measurements with substantial caveats are also available14. Here we report radiation measurements from the heavily shielded Orion spacecraft on the uncrewed Artemis I lunar mission. At differing shielding locations inside the vehicle, a fourfold difference in dose rates was observed during proton-belt passes that are similar to large, reference solar-particle events. Interplanetary cosmic-ray dose equivalent rates in Orion were as much as 60% lower than previous observations9. Furthermore, a change in orientation of the spacecraft during the proton-belt transit resulted in a reduction of radiation dose rates of around 50%. These measurements validate the Orion for future crewed exploration and inform future human spaceflight mission design.

Laboratory demonstration of an off-axis optical bench design for future gravity missions.

The inter-satellite laser ranging interferometer is one of the core components of future gravity missions to achieve high ranging precision. This work builds a preliminary breadboard of the off-axis optical bench design, which integrates the merits of the off-axis optical bench design of GRACE Follow-On mission and other on-axis designs. The study finds that the displacement noise between two optical benches has been reduced to 20nm/Hz at a frequency of 10 mHz, and the differential wavefront sensing noise has been suppressed to 10-5rad/Hz at 1kHz as well. In addition, the tilt-to-length coupling noise related to the piston effect is restricted within 30μm/rad, and the relative parallelism error of the transmitting beam and receiving beam is less than 4.5%. The results show that this off-axis optical bench design is an important candidate for China's future gravity missions.

Mutation Operator for Resonance Flybys in Moon Tour Design Optimization

The global optimization of the moon tour design problem is addressed in this paper. These missions are usually designed using graphical methods or grid search, which require simplifying assumptions, and a skillful mission designer. The grid search methods are computationally intense. Trajectories with a high number of flybys and multiple resonance flybys are usually hard to optimize, especially with small-size/short-period flyby moons. This work proposes a new mutation operator that is incorporated with the Monotonic Basin Hopping in the Evolutionary Mission Trajectory Generator tool; this mutation operator increases the exploration of resonance flybys to improve convergence in moon tour design optimization problems. In this work, the Hidden Genes Genetic Algorithm is used to optimize the undetermined number of moon flybys. A Europa Clipper-like mission is optimized assuming two-body dynamics, and a validation study for the proposed resonance mutation operator is presented. The results include an optimized baseline solution and a new solution with a different sequence of flybys with a different sequence of flybys for the Europa Clipper-like mission, in addition to an optimized moon tour in the Saturnian system.

Model-Based Systems Engineering: Pioneering New Era in Astrophysics Mission Design

Model-Based Systems Engineering: Pioneering New Era in Astrophysics Mission Design

SALTUS probe class space mission: observatory architecture and mission design

SALTUS probe class space mission: observatory architecture and mission design

Mission design for space telescope servicing at Sun–Earth L2

The Sun–Earth Lagrange points, L1 and L2, are excellent locations for space based observatories, due to their favorable dynamical and environmental properties. Space telescopes, however, come with an extremely high price tag, and without refueling and servicing the typical lifetime is only about ten to fifteen years. The return on investment of a space telescope could be significantly increased by developing on-orbit servicing and refueling capabilities, assuming that the servicing vehicle can be launched at a fraction of the cost of the original mission and that the lifetime of the space telescope can be significantly extended to allow for continued scientific activity. In this paper we demonstrate the feasibility of this class of servicing mission from a trajectory design perspective, using novel techniques that we have developed for quick sampling of the solution space, as well as an efficient and reliable means to obtained high-fidelity, time-optimal, end-to-end transfer trajectories. As candidates for this investigation we consider Gaia and the James Webb Space Telescope. Our trajectory design methodology is, however, general enough to be applicable to future space observatories that are designed to be serviceable in space.

Semantic-based systems engineering for digitalization of space mission design

The engineering of space systems is a collaborative, iterative process that integrates various domain-specific viewpoints to represent the final system. To ensure consistency across these viewpoints, the European Space Agency (ESA) employs Model-Based System Engineering (MBSE) and Semantic-Based System Engineering (SBSE) methodologies together to improve digital continuity and interoperability across collaborative space system developments. One significant application of semantic engineering in SE is the ESA MBSE Methodology. The ESA MBSE Methodology provides a standardized approach aligned with the European Cooperation for Space Standardization (ECSS), promotes interoperability across MBSE methodologies and tools, and overcomes integration challenges. ESA MBSE Methodology is the input for the Overall Semantic Modeling for Space System Engineering (OSMoSE) which leverages interoperability in the space community. Case studies, such as the EagleEye Earth Observation mission, demonstrate practical applications, highlighting how semantic models enhance efficiency in complex space systems. This paper discusses the importance of semantics and data management in SE and presents a practical solution derived from the ESA MBSE Methodology.

Path planning of 6-DOF free-floating space robotic manipulators using reinforcement learning

This paper presents a study on path planning for 6-DOF free-floating space robotic manipulators using Deep Deterministic Policy Gradient-based Reinforcement Learning. The focus is the development of a novel reward function tailored to address critical requirements for efficient and effective manipulation in space. These requirements include accurate pose alignment between the end-effector and the target, collision avoidance with both the target and other links of the manipulator, smoothing of joint velocities, adaptability to strong dynamic coupling between the manipulator and its base spacecraft due to high manipulator-spacecraft mass ratio, and resilience to noise in the state observations. Uniquely, the proposed reward function employs quaternions for orientation control to reduce pose misalignments and dynamic singularities, as opposed to traditional Euler angles. Our findings demonstrate that the Reinforcement Learning algorithm, when guided by this new reward function that integrates these enhancements and constraints, not only achieves the desired path planning objectives more efficiently but also exhibits faster convergence. Furthermore, the Reinforcement Learning successfully manages significant dynamic coupling effects caused by a high mass ratio between the robotic manipulator and the base spacecraft. Even under the challenge of noisy state observations, the trained agent successfully completes the path planning task, proving the Reinforcement Learning's applicability to real-space mission designs where the noise in observation is inevitable. The study highlights the critical role of reward function design in the Reinforcement Learning training process and its consequential impact on the solution quality, providing a solid foundation for future advancements in free-floating space robotic missions.

Constellation design and performance of future quantum satellite gravity missions

Temporal aliasing is currently the largest error contributor to time-variable satellite gravity field models. Therefore, the evolution of sensor technologies has to be complemented by strategies to reduce temporal aliasing errors. The most straightforward way to improve temporal aliasing is through extended satellite constellations because they improve the observation geometry and increase the achievable temporal resolution. Therefore, strategies to optimize the design of larger satellite constellations are investigated in this contribution. A complete constellation modeling procedure is presented, starting from primary design variables (such as the required targeted resolutions) and concluding with concrete orbital elements for the individual satellites. In parallel, it is evaluated if improved instrument sensitivities based on quantum technologies (cold atom interferometry) can be fully exploited in the case of larger constellations. For this, future quantum satellite gravity missions adopting the gradiometry concept (similar to the GOCE mission) and the low-low satellite-to-satellite tracking concept (similar to GRACE/-FO) are simulated on optimized constellations with up to 6 satellites/pairs. The retrieval performance of a 6-pair mission in terms of the global equivalent water height RMS can be improved by a factor of roughly 3 compared to an inclined double-pair mission. 3D-gradiometry intrinsically has a better de-aliasing behavior but has extremely high accuracy requirements for the gradiometer (about 10 µEotvos) and the attitude reconstruction to be of any benefit. All simulations show that when incorporating improved sensor technologies, such as future quantum sensing instruments in extended constellations, temporal aliasing will remain the dominant error source by far, up to five orders of magnitude larger than the instrument errors. Therefore, improving sensor technologies has to go hand in hand with larger satellite constellations and improved space–time parameterization strategies to further reduce temporal aliasing effects.Graphical

Robotic exploration of Martian caves: Evaluating operational concepts through analog experiments in lava tubes

Caves on Mars are a tantalizing target for exploration, as they could harbor evidence of extinct or extant life, clues to the planet’s geological history, and even potential future human habitation. However, the inherent challenges of navigating unknown and challenging terrain, coupled with limited communication capabilities, pose significant obstacles for robotic exploration in these caves. This paper presents the results of an effort to evaluate different operational concepts for a mission dedicated to exploration of caves on Mars. We conducted a series of analog exploration experiments in lava tubes on Earth, testing two hypotheses: (1) that two robots are more effective than one, and (2) that high levels of autonomy are more effective than low levels of autonomy. Our findings suggest that two robots are indeed more effective, except in low autonomy cases, where more operational resources are required. We also found that full autonomy is more efficient than low autonomy, as it enables quicker exploration and detection of targets of interest. However, the low autonomy cases benefited from the operator input to acquire higher quality data, an area of autonomy requiring further development. This paper provides insight into the design of our experiments, as well as detailing the results and implications for the design of future missions to explore caves on Mars. By shedding light on the operational concepts tested and their corresponding outcomes, we contribute to the knowledge base required to formulate optimal strategies for the realization of successful cave exploration missions on the Red Planet.

Altitude optimality boundary of two variants of large space debris removal to disposal orbits

The article considers the mission design problem for removal of large space debris objects from near-Earth orbits. It is assumed that a single active spacecraft-collector (SC) should de/re-orbit several objects. The upper planning level calls for a scenario that specifies the type of repeating operations of an SC. Despite the apparent diversity of these scenarios, they can be reduced to two variants of objects removal to disposal orbits (DOs). In variant I, transfers between objects are effected by an SC with detachable propulsion modules (PMs) onboard. Once the next-in-line object is captured, one module is accommodated on its surface, and, after demating, this PM ensures the relocation of the object to a DO. In variant II, the SC operates as a tug vehicle and transfers the object to DO on its own, and then returns to the next object.A reasonable choice of the removal variant depends on the SC launch mass which should be compared for the same number of de/re-orbited derelict targets. To this end, one should estimate the SC dry mass, the payload mass, and the SC propellant mass. Each of these three terms is nonlinear and depends explicitly on each other, the mass of the captured object, and on the SC maneuvers. Analytical models are proposed for estimation of the SC launch mass for each of the two removal variants. It is also shown that there exists an altitude optimality boundary (the radius of a spherical layer) above which the removal variant II is more advantageous than variant I. Such models are constructed based on several assumptions capable of breaking the iterative search of the SC launch mass.The position of the altitude optimality boundary depends on seven input parameters of the mission: the SC dry mass; the PM dry mass; the mass of the object, the required variation of the semi-major axis Δa to reach the DO, the number of objects removed by a single SC, the average ΔV for a transfer between two objects, and the effective exhaust velocity of SC main engine. In the present paper, four types of objects are considered: heavy and light LV stages in low orbits, upper stages in GEO and GNSS regions. By choosing concrete objects of study one can substantially reduce the solution space by excluding the impossible combinations of input data. By using the developed SC launch mass models, it is possible to formulate removal recommendations for concrete groups of space debris objects. These models were shown as being adequate on the examples of Elsa-M and MRV projects which are due to be implemented in the next one-two years.