Desert Conditions Research Articles

The apparatus for atmospheric water harvesting in an arid climate - Prototype design and testing in laboratory conditions

The paper describes the development of a prototype system for water extraction from the air. The aim was to develop a device that allows one to autonomously obtain, without the need for external energy, an annual average of 100 L of water per day during extreme desert conditions. In this paper, a mathematical model simulating the operation of the unit for extracting water from the air in any climatic conditions is presented. Psychrometric calculations for different climatic conditions were carried out for two basic principles: condensation and sorption. The analyses confirmed that devices based on the condensation of water vapour from the air can only be used to a limited extent in extreme desert conditions. The average water production of a condensation-based system is only 20 l/day in Riyadh, with an air flow rate of 2000 m3/h. A unit with a desiccant wheel and an integrated heat pump was designed for water harvesting from the air. The prototype of the unit was tested in a climate chamber with the possibility of adjusting the climatic conditions and the presented mathematical model was experimentally verified. The final prototype designed for a nominal outdoor air flow rate of 2000 m3/h will produce 168 l of water per day under dry desert conditions (Riyadh) with continuous operation. The verification of the computational model allows one to determine the real water production and the required unit performance. An analyses of energy requirements and evaluation of levelized cost of water (LCOW) have been performed. Sorption unit has lower LCOW in target arid desert climate and electricity prices under 0.1 EUR/kWh compared to direct condensation technology.

Fixing active sand dune by native grasses in the desert of Northwest China

BackgroundDesertification is the most severe environmental problem in arid and semi-arid regions and has caused great economic loss every year. However, artificial sand fixation barriers function on sand fixation for only 10–20 years. Searching for a native species with long-term sand fixation effect and strong environmental adaptive capacity, and low water consumption is needed. In this study, we investigated the environmental adaption and sand fixation effect of a grass from Poaceae family (Psammochloa villosa) that is indigenous to the desert of Northwest China.ResultsThe results showed that P. villosa has a streamlined leaf form, strong mechanical strength, and flexibility to adapt to wind. Leaf curling of P. villosa under drought decreased water loss rate through decreased evaporation area to adapt to drought. Significant negative relationship between adventitious root length and horizontal root burial depth indicates that adventitious roots help P. villosa absorb water and nutrients from soil under shallow sand burial condition, which enables P. villosa to adapt to different sand burial conditions. P. villosa fixed sand dunes through the distribution of the population at the top of the dune and the vertical relationship between the direction of windblown sand and the direction of growth of P. villosa, which stopped the expansion of the dune.ConclusionsGrowth characteristics of wind and drought tolerant leaf traits and adventitious roots under sand burial indicate that P. villosa is well adapted to dry sandy desert conditions and burial by sand. The distribution of the P. villosa population on the sand dune is a “brake” on its expansion. These findings provide new insight for active sand dune fixation and desertification control using native grass in the desertified regions.

Cosmogenic 10Be‐ and 21Ne‐based model exposure ages of desert pavements in the Thar Desert, India

AbstractThe Thar Desert, India has desert pavements comprising angular‐subangular to well‐rounded gravels at marginally higher elevations than the surrounding terrain. Sedimentological and geomorphic analyses suggest that the pavements are lags of weathered Mesozoic and older bedrock. The presence of Palaeolithic artefacts on the pavement surfaces and occasionally within their matrix was used to infer their antiquity and landscape stability.This study presents the first surface exposure ages based on cosmic‐ray‐produced 10Be and 21Ne for pavements at four sites in the Thar Desert, viz. Bhojka, Hamira, Solanki and Jayal. The computation of model exposure ages assumed that (a) the gravels were derived from cemented conglomerates, uplifted by tectonics and thereafter disintegrated by climate, and (b) cosmogenic nuclide production in the gravels began when the conglomerates approached the surface and, continued during their disintegration, gravity sliding of individual gravels and storage, until the present. Assuming an average burial depth of 50 cm, 21Ne and 10Be data provide ages ranging from 1.30 to 2.92 Ma and 1.11 to 5.4 Ma, respectively, for the two nuclides.Published electron spin resonance ages of Thar calcretes suggest the presence of water and extreme seasonality since 1.54 Ma. Such conditions facilitated the mobilization and precipitation of carbonates. The pavement ages and the minimum age of the conglomerate at 2.51 Ma extend the time of such desertic conditions to > 2.51 Ma and suggest that the initiation of desertic conditions in the Thar was possibly linked to global aridity beginning around 3.6 Ma.Depending on assumptions, cosmic ray surface exposure (10Be) ages at Jayal range between 0.76 and 2.43 Ma. In the context of the Indian Palaeolithic, the presence of tools on the gravel surfaces and within dunes, suggests frequent occupation of this region from at least 0.76 Ma and, parallels Early to Middle Pleistocene Acheulian assemblages from Southern India.

The complex chemical effects of air pollutants, meteorology and dust on the concentrations of criteria and non-criteria air pollution in Kuwait

Air pollution is the leading environmental health risk factor globally. A number of cities experienced improvements in air quality during the COVID-19 lockdown; however such changes depend on the contributions from natural and anthropogenic sources and meteorological factors pertaining to each city. This study investigated the effects of anthropogenic and meteorological factors on air quality in Kuwait during the COVID-19 lockdown (22 March–10 May 2020) using mixed-effect regression and machine learning models. Criteria (PM2.5, PM10, NO2, O3, SO2, CO) and non-criteria (C6H6, NH3, H2S, NMHC) air pollutants were compared between the lockdown period, and the same period in the preceding and the following years, 2019 and 2021, respectively. The results showed that during the lockdown three criteria air pollutants (PM2.5, NO2, CO) were reduced by 38, 40, 26%, respectively. All no-criteria air pollutants were reduced, except for H2S. The arid region’s harsh desert conditions have major contributions to particulate pollution. Although PM levels are overwhelmed by meteorological and natural dust, stringent abatement measures on oil/gas hydrocarbon and power plant emissions can significantly reduce PM and other pollutants. Abatement measures on traffic pollution can further reduce the NO2 levels. This study highlights Kuwait's ongoing struggle with elevated levels of particulate and gaseous pollution, driven by hydrocarbon emissions and dust. Effectively tackling air quality requires a nuanced understanding of the interplay between air pollutants, meteorological, and dust covariates.

Morphological and Germination Characteristics of Alhagi maurorum Boiss. and Salsola richteri Kar. Seeds Distributed in the Karakum Desert of Turkmenistan

The Karakum Desert is the largest desert in Turkmenistan and covers a significant part of Central Asia. This desert is home to plant species that can adapt to hot, dry, and barren conditions. During the summer months, the Karakum Desert can get extremely hot, with temperatures reaching up to 50 °C, while in winter, it can drop to -20 °C. Therefore, the desert conditions significant seasonal temperature differences. In winter, rainfall is very low, snow rarely falls, and quickly melts. Afghan winds have an impact on the desert vegetation. The desert vegetation mainly consists of short grasses and woody shrubs. Despite the scarcity of rainfall and high temperatures during the summer months, steppe plants have generally been able to adapt to the harsh conditions of the desert. There are also species that have adapted to the desert climate, such as Alhagi maurorum Boiss., Haloxylon persicum Bunge, Haloxylon aphyllum (Minkw.) Iljin), Solanum nigrum L., and Salsola richteri Kar. These plants are highly valuable in terms of nutrition for animals and are used as winter animal feed in rural areas. In this study, the seed and germination characteristics of Alhagi maurorum Boiss. and Salsola richteri Kar, which are tree and shrub-like plants that can adapt to Karakum Desert conditions, were examined. In laboratory study, the morphological characteristics of the seeds were determined, and vitality and germination tests were conducted. Information was obtained about the germination adaptation of these plants in desert ecosystems. As a result of the study, it was determined that S. richteri had a very low rate of viable seeds and no germination, while the germination process of Alhagi maurorum could take a considerably long time.

Effects of Microbiota on the Soiling Process of PV Modules in Arid Zones of the Atacama Desert

Photovoltaic technology has proven to be a reliable, economical, and clean energy source that is capable of adapting to diverse geographical conditions. However, factors such as soiling overshadow these qualities, thus leading to production losses and affecting the profitability of this technology. For these reasons, soiling is a highly studied topic, which involves considering the physicochemical characterization of the deposited material, mitigation strategies, effect predictions, and cleaning mechanisms. However, there is a relatively unexplored area related to the microbiological contribution to soiling. The surface of photovoltaic modules, along with the deposited material and local atmospheric factors, fosters favorable conditions for the colonization of microorganisms. These microorganisms influence the soiling mechanisms and optical properties of photovoltaic modules. This work presents a detailed characterization of the microbial diversity present in the soiling deposited on photovoltaic modules installed in the Atacama Desert. Two study sites were defined: Antofagasta and the Solar Platform of the Atacama Desert, which have warm and cold desert climates, respectively. Mineralogical characterization tests, heavy metal analyses, TOC, and inorganic element analyses were conducted on the deposited material. Additionally, the culturable isolates and the metagenomic DNA of the soiling samples and biofilms grown on standard PV glass were characterized using next-generation sequencing. The results show that the deposited soiling contained a microbiological component that had adapted to extreme desert conditions. The presence of the genera Arthrobacter, Kocuria, and Dietzia were identified in the culturable isolates from Antofagasta, while Arthrobacter and Dietzia were obtained from the Solar Platform of the Atacama Desert. The metagenomic DNA was mainly represented by the genera Pontibacter, Noviherbaspirillum, Massilia, Arthrobacter, Hymenobacter, and Deinococcus at Antofagasta. However, at the Solar Platform of the Atacama Desert, the analyzed samples presented DNA concentrations below 0.5 ng/µL, which made their preparation unviable. At the PSDA, the biofilms formed by the genera Peribacillus and Kocuria were identified, whereas the UA showed a greater abundance of bacteria that favored biofilm formation, including those that belonged to the genera Bacillus, Sporosarcina, Bhargavaea, Mesaobacillus, Cytobacillus, Caldakalibacillus, and Planococcus. Based on these results, we propose a soiling mechanism that considers the microbiological contribution to material cementation.

Long-term performance analysis of a large-scale photoVoltaic plant in extreme desert conditions

This study comprehensively evaluates the performance and operational challenges of a 9 MW grid-connected photovoltaic (PV) system in Timmimoun, southern Algeria, after eight years of operation. We identified a significant linear correlation (R2 = 0.73) between increased ambient temperatures and decreased PV module efficiency, underscoring the need for effective thermal management strategies. The investigation also examines potential solutions, such as cooling mechanisms, optimization of panel orientation and tilt angles, and development of temperature-resistant materials. Adhering to the International Energy Agency IEC 61724 standard, our analysis reveals a yield factor of 5.04 h/day, a yield ratio of 7.04 h/day, a performance ratio of 73 %, and a capacity factor of 21 % in 2023. Over its operational lifespan, the system has generated 133.43 GW h of energy, mitigating 1.01 105 tons of CO2 emissions. This long-term study provides critical insights into the performance and reliability of PV systems in hot desert climates, offering valuable guidance for future large-scale solar installations and contributing to the transition towards a sustainable energy future.

Native arbuscular mycorrhizal fungi drive ecophysiology through phenotypic integration and functional plasticity under the Sonoran desert conditions.

Knowledge is scarce to what extent environmental drivers and native symbiotic fungi in soil induce abrupt (short-term), systemic (multiple traits), or specific (a subset of traits) shifts in C3 plants' ecophysiological/mycorrhizal responses. We cultivated an emblematic native C3 species (Capsicum annuum var. glabriusculum, "Chiltepín") to look at how the extreme heat of the Sonoran desert, sunlight regimes (low = 2, intermediate = 15, high = 46 mol m2 d-1) and density of native arbuscular mycorrhizal fungi in soil (low AMF = 1% v/v, high AMF = 100% v/v), drive shifts on mycorrhizal responses through multiple functional traits (106 traits). The warming thresholds were relentlessly harsh even under intensive shade (e.g. superheat maximum thresholds reached ranged between 47-63°C), and several pivotal traits were synergistically driven by AMF (e.g. photosynthetic capacity, biomass gain/allometry, and mycorrhizal colonization traits); whereas concurrently, sunlight regimes promoted most (76%) alterations in functional acclimation traits in the short-term and opposite directions (e.g. survival, phenology, photosynthetic, carbon/nitrogen economy). Multidimensional reduction analysis suggests that the AMF promotes a synergistic impact on plants' phenotypic integration and functional plasticity in response to sunlight regimes; however, complex relationships among traits suggest that phenotypic variation determines the robustness degree of ecophysiological/mycorrhizal phenotypes between/within environments. Photosynthetic canopy surface expansion, Rubisco activity, photosynthetic nitrogen allocation, carbon gain, and differential colonization traits could be central to plants' overall ecophysiological/mycorrhizal fitness strengthening. In conclusion, we found evidence that a strong combined effect among environmental factors in which AMF are key effectors could drive important trade-offs on plants' ecophysiological/mycorrhizal fitness in the short term.

Mechanism of developing early strength of Portland cement-desert sand system under radiation in desert conditions

Infrastructure development in desert areas like desert highways places demands on sand fixation. While prior research has examined the effects of temperature and ultraviolet light on mortar, the use of Portland cement in desert areas has received minimal attention. This study examines the process of strength development in the Portland cement-desert sand (PC-DS) system under alternating infrared and ultraviolet radiation during day and night cycles. Characterization of the mechanical properties through surface penetration strength (SPS) and compressive strength (CS) was performed, and the strength growth mechanism of the PC-DS was investigated through microstructural characterization via XRD, SEM, FTIR, and TG-DTG. The results indicate that the strength of the PC-DS system peaked at 3d and decreased to 2 MPa at 7d, a decrease of 1/9, associated with the gypsum generation. Infrared radiation decreased the PC-DS system strength to 1.4 MPa after 7d, while the strength was essentially unchanged at 7d of ultraviolet radiation. Further studies revealed that infrared radiation raised the temperature from 24 °C to 40 °C, accelerating the cement hydration while accelerating water volatilization. Ultraviolet radiation enhances the cement carbonation reaction, carbonization reaction increases by 1/4, reducing the Ca2+ concentration and hindering the gypsum formation. Microscopic experimental results showed that no new substances and structures were produced under infrared and ultraviolet radiation. This finding has implications for the facilities construction and sand fixation in desert areas.

Evaluation of clear-sky surface downwelling shortwave fluxes computed by three atmospheric radiative transfer models

In this study the clear-sky total, direct, and diffuse shortwave (SW) fluxes at the surface, have been calculated by three radiation transfer models (RTMs) – MODTRAN6.0 (M6.0), Canadian Centre for Climate Modelling and Analysis (CCCma), and Langley-modified Fu-Liou (NASA CERES). These calculations have been evaluated by surface measurements collected from seven sites that represent different climatological regimes with various surface scene types including ocean, grassland/continental, desert, and snow/sea ice. For pristine atmospheric conditions, SW fluxes predicted by CCCma and M6.0 shows little variation, which lays a baseline for further analysis. Note that computing time required by CCCma is ∼1000 times smaller than M6.0. Based on all samples collected from seven sites, mean differences of total, direct, and diffuse fluxes between surface measurements and CCCma / M6.0 / Fu-Liou are [5.3 / 2.4 / 0.9], [-2.2 / -5.1 / -13.7], and [7.5 / 7.5 / 14.6] W m-2, respectively. Histograms of differences between the three RTM calculations and surface measurements show that CCCma computed direct and diffuse fluxes have the smallest biases with standard deviations similar to those for M6.0, while Fu-Liou values have the largest biases and standard deviations. While Fu-Liou outperforms for total flux, especially for desert conditions, it is hampered by large biases for direct and diffuse across all scene types. The three RTMs are consistent with showing the least error for total flux and the largest in diffuse based on bias, correlation, and root mean square error.

Melon Grafting Effects on Plant Performance and Yield in the High Desert

Farmers in the high desert are challenged by a short growing season and slow crop establishment of warm-season vegetables. Yet an increasing demand for local produce in nearby urban areas presents an opportunity to diversify farms while adapting to climate uncertainty. Vegetable rootstocks can confer advantages under biotic and abiotic stress conditions, but information on which and how melon rootstocks can improve management does not exist for high desert and short-season regions. Commercial, squash-hybrid rootstocks (i.e., Cucurbita maxima × C. moschata) were grafted with a common scion (Cucumis melo cv. Sarah’s choice). Nine rootstocks in 2021 and four selected rootstocks in 2022 were evaluated in four field trials (two per year) in northern Nevada at two distinct locations. Melon grafting did not consistently increase crop performance in the high desert, and it was influenced by location and year. Throughout the initial half of the harvesting period, grafted plants tended to produce more melons, irrespective of location or year, offering a potential appeal for melon growers operating in shorter growing seasons. However, a slight reduction in fruit quality (i.e., °Brix) was observed in some grafted plants compared with the ungrafted control. The benefits of grafting melons onto squash hybrids in high desert conditions remain uncertain and may depend on microenvironment and farming practices that affect crop establishment, such as mulching effects on soil temperature.

Blue carbon assessment in Avicennia marina sediments and vegetation along the Red Sea Coast of Egypt: Improving methods and insights

Mangrove forests play a crucial role in the coastal environment. A plethora of research is focusing on mangroves’ role in climate mitigation through sequestering and storing CO2. This study aims to assess the organic carbon (OC) stocks and carbon sequestration rate (CSR) of the largest stands of mangroves in the Red Sea Coast of Egypt, to evaluate their significance in climate mitigation strategies. Intensive sampling was conducted in mangrove stands of Safaga, Qulaan, and Hamata to investigate OC and sediment properties along depth intervals to 1 m deep. Additionally, OC stored in the above- and below-ground biomass was estimated using Landsat 9 OLI/TIRS satellite images. TOC content (∼0.50%) and stocks in the sediments (54.49 ± 31.71–86.00 ± 29.00 MgC/ha) were very low compared to the global average for mangrove stands, and comparable to the mangrove forest in the Middle East region. This can be attributed to the desert and semi-desert conditions, limited riverine input, and low precipitation rates. Moreover, the above-ground biomass, estimated from Normalized Difference Vegetation Index, exhibited extremely low OC storage. Therefore, the sediment acted as the main pool of organic carbon in these mangrove ecosystems. The research findings revealed that mangrove stands in Egypt exhibit low CSR, ranging from 11.94 to 18.02 g C m−2 year−1. Additionally, the study determined that the stable nature of mangrove stands in Egypt makes their annual CO2 emissions negligible. Despite local studies suggesting otherwise, it is highly unlikely that mangroves in Egypt contribute to the climate mitigation related to CO2 sequestration. Therefore, it is important to implement restoration plans to ensure the preservation of other ecological services provided by mangroves along the Red Sea Coast.

Experimental Demonstration of a Solar Powered High Temperature Latent Heat Storage Prototype

The challenge of imbalances between renewable energy supply and grid demand underscores the significance of energy storage in microgrids. This research presents an empirical assessment of the operational capabilities of a full-scale Electrical Thermal Energy Storage (ETES) prototype system named Thermal Energy Storage Power On Demand (TES.POD®), in solar-abundant and harsh desert conditions. The system incorporates a high-temperature commercial-scale latent heat thermal energy storage, integrated with a Stirling engine. Over a continuous span of 10 days, from September 26th to October 6th, 2022, the input and output power, as well as the heat transfer fluid temperatures during charging and discharging were monitored to assess the power block and system efficiencies. Results from the experiments reveal that this prototype effectively maintains a near-constant electricity production rate of 10.5 ± 1 kW for a discharge duration of 13 hours. Average cycle efficiency stands at 23%, while power block efficiency reaches 25%. These findings collectively suggest the system's potential for applications involving long duration thermal energy storage.

Cultivation of Limnospira maxima under extreme environmental conditions in Saudi Arabia: Salinity adaptation and scaling-up from laboratory culture to large-scale production

Limnospira maxima has been adapted to grow in high salinity and in an economically alternative medium using industrial-grade fertilizers under harsh environmental conditions in Saudi Arabia. A sequence of scaling-up processes, from the laboratory to large-scale open raceways, was conducted along with gradual adaptation to environmental stress (salinity, light, temperature, pH). High biomass concentration at harvest point and areal productivity were achieved during the harsh summer season (1.122 g L−1 and 60.35 g m−2 day−1, respectively). The average protein content was found to be above 40 % of dry weight. Changes in the color and morphological appearance of the L. maxima culture were observed after direct exposure to sunlight in the outdoor raceways. These results demonstrate a successful and robust adaptation method for algal cultivation at outdoor large-scale in harsh environment (desert conditions) and also prove the feasibility of using hypersaline seawater (42 g kg−1) as an algal growth medium.

Effect of Spraying Fenugreek and Licorice Root Extracts on Improving the Quality of Flame Seedless Grapes under Desert Conditions

Effect of Spraying Fenugreek and Licorice Root Extracts on Improving the Quality of Flame Seedless Grapes under Desert Conditions

Suns-Vmp method for health monitoring of 110 PV modules

One can monitor the health of the PV modules by analyzing their current-voltage (I–V) curves, which rarely are measured in commercial settings. Fortunately, nearly all PV installations measure the maximum power point current (Imp) and voltage (Vmp), along with the ambient weather conditions, which the proposed Suns-Vmp method uses to generate pseudo I–V curves. In this work, the proposed methodology was rigorously tested on 110 PV modules of various technologies installed under harsh desert conditions, for approximately 7 years and 9 months. For these modules, the fitting accuracy between the actual field measured and pseudo I–V curves, did not exceed an RMSE value of 0.35 A. The median power degradation of the mono-crystalline, poly-crystalline, and thin-film technologies were estimated to be around 0.21 %/year, 0.49 %/year, and 1.51 %/year. From the root-cause analysis using the fitted PV parameters, it was found that the dominant degradation contribution in all the modules came from series resistance, followed by shunt resistance. For mono-crystalline, poly-crystalline, and thin-film technologies, the mean yearly rate of change for series resistance was 1.47 %, 4.37 % and 13.37 %, while for shunt resistance these values were 0.68 %, 1.26 % and 3.95 % respectively. As field measured I–V curves are seldom available, techniques like the Suns-Vmp method can offer valuable insights for effective solar farm management and maintenance, without any interruption in the operation.

Regulation of a single inositol 1-phosphate synthase homeologue by HSFA6B contributes to fibre yield maintenance under drought conditions in upland cotton.

Drought stress substantially impacts crop physiology resulting in alteration of growth and productivity. Understanding the genetic and molecular crosstalk between stress responses and agronomically important traits such as fibre yield is particularly complicated in the allopolyploid species, upland cotton (Gossypium hirsutum), due to reduced sequence variability between A and D subgenomes. To better understand how drought stress impacts yield, the transcriptomes of 22 genetically and phenotypically diverse upland cotton accessions grown under well-watered and water-limited conditions in the Arizona low desert were sequenced. Gene co-expression analyses were performed, uncovering a group of stress response genes, in particular transcription factors GhDREB2A-A and GhHSFA6B-D, associated with improved yield under water-limited conditions in an ABA-independent manner. DNA affinity purification sequencing (DAP-seq), as well as public cistrome data from Arabidopsis, were used to identify targets of these two TFs. Among these targets were two lint yield-associated genes previously identified through genome-wide association studies (GWAS)-based approaches, GhABP-D and GhIPS1-A. Biochemical and phylogenetic approaches were used to determine that GhIPS1-A is positively regulated by GhHSFA6B-D, and that this regulatory mechanism is specific to Gossypium spp. containing the A (old world) genome. Finally, an SNP was identified within the GhHSFA6B-D binding site in GhIPS1-A that is positively associated with yield under water-limiting conditions. These data lay out a regulatory connection between abiotic stress and fibre yield in cotton that appears conserved in other systems such as Arabidopsis.

Assessing Survival of Transgenic Bacteria, Serratia AS1 and Enterobacter cloacae, in Sugar Bait, White Saxaul Plant (Haloxylon persicum) and Rodent Barrow's Soil, A Contained-Field Study for Paratransgenesis Approach.

The viability and persistence of engineered bacterium candidates in field conditions is one of the considerable challenges in the paratransgenesis approach to fighting vector-borne diseases. In this study two engineered bacterium candidates to produce paratransgenic sand flies, Serratia AS1 and Enterobacter cloacae expressing m-Cherry fluorescent were applied on the leaves of the white saxaul plant (Haloxylon persicum), sugar bait, and rodent burrow soil and their persistent time was tested in desert condition, Matin Abad County, Isfahan, August 2022. A PBS suspension of 109 cells/ml was used for sugar bait, spraying on plant leaves (∼10 cm2) and 10 cm2 of rodent burrow soil. Sand fly samples were taken daily and were plated on LB Agar and the fluorescent cells were counted after 24 hours. Time course in general caused a decrease in the number of bacteria for both strains. The two strains were persistent in sugar bait and on plant leaves for four days and on soil for two days. Although there were slight differences between the number of the bacteria in sugar baits, which was not significant (P< 0.05). The number of E. cloacae surviving on plant and in soil were significantly (P< 0.0001 and P= 0.046) higher than Serratia AS1. This study shows that plants or sugar bait are useful routes for delivery of the transformed bacteria for the paratransgenesis approach, although, the bacteria ought to be sprayed on plants or sugar baits should be replaced with new ones in four days intervals.

Pilot testing of water utilization for integrated solar energy storage and power production using linear Fresnel collector and organic Rankine cycle

This work presents a new method of utilizing water as thermal energy storage to improve the capacity factor of integrated linear Fresnel collector – organic Rankine cycle (LFC-ORC). A new process flow diagram has been proposed to manage overnight operation of the ORC relying on thermal energy storage in water. Pilot testing of 10 kW capacity of LFC-ORC process under arid and desert conditions of Arabian Gulf operating conditions (Qatar) is also reported. A thermodynamic analysis has been performed based experimental evaluation and process simulation of the LFC-ORC production and efficiency. The LFC-ORC operations at storage temperatures of 170 °C showed peak electricity production of 6.76 kW (38 W/m2 aperture area of LFC) whereas 1st law, and 2nd law efficiencies were 6 % and 19 %, respectively. An operational strategy is proposed to generate 5 kW over a period of about 12 h using 10 m3 storage capacity. The developed process simulation program showed that two LFC systems, each 176 m2 aperture area, equipped with three storage tanks each 10 m3, must be installed to generate 5 kW electricity for 24 h. The proposed system can be upscaled to any size as per end-user needs. The new system design would be subjected to further optimization and feasibility to cope with the development of the ORC and LFC efficiency in the future.

Impact of sand feed rate on the damage of railway wheel steels

The global railway industry plays a pivotal role in economic development, offering efficient transportation solutions. However, railways operating in desert environments face unique challenges due to windblown sand. This study investigates the influence of sand feed rates on wheel-rail wear in desert conditions. Experimental tests were conducted using a bidisc apparatus to simulate sand feed rates. Results indicate that low feed rates lead to spalling and pitting, while high rates increase abrasive and fatigue wear. A critical transition point at 0.4 g/min suggests sand-induced abrasion of wheel surfaces. Moreover, the research highlights the crucial role of sand feed rates not only in wear but also in surface roughness, further emphasizing the complex interplay between sand transport rates, adhesion, and wear mechanisms. These insights provide valuable guidance for mitigating wear-related challenges in desert railway operations and optimizing maintenance strategies.