Dense Wavelength Division Multiplexing Research Articles

Multipoint temperature measurement system composed of fiber-optic Fabry–Perot interference sensors and a wavelength-division multiplexing filter

A multipoint optical-fiber remote temperature measurement system was developed using reflection-type sensors consisting of a Fabry–Perot interference (FPI) structure with good temperature characteristics combined with a wavelength-division multiplexing (WDM) filter. The FPI sensor was fabricated using a short temperature-sensing region sandwiched between single-mode fibers. FPI optical fibers and a WDM filter functioned as the temperature sensors and wavelength-selective optical source using an amplified spontaneous emission light source, respectively. This system was operated in a dense WDM configuration using an arrayed waveguide wavelength filter.

Dense Wavelength Division Multiplexing (DWDM) in IT Networks: A Leap Beyond Synchronous Digital Hierarchy (SDH)

The evolution of telecommunications has seen significant milestones, notably the shift from Synchronous Digital Hierarchy (SDH) to Dense Wavelength Division Multiplexing (DWDM). This transition marks a pivotal advancement in the performance of Information Technology (IT) networks, offering unparalleled improvements in bandwidth, scalability, and efficiency. DWDM technology enables the simultaneous transmission of multiple data streams across a single optical fiber by using different wavelengths of light, significantly enhancing data throughput and network capacity. This article delves into the technical foundations of DWDM, compares its performance enhancements over SDH systems, and explores its impact on modern IT network infrastructure.

Metallic layered VSe2 saturable absorber based single- and dual-wavelength ultrafast fiber laser

Vanadium selenide (VSe2) is a special two-dimensional (2D) transition metal dichalcogenide (TMD) material with metallic properties similar to graphene, which has been proved to have saturable absorption properties and used in mode-locked fiber lasers. As an excellent saturable absorber (SA) material, VSe2 has advantage of ultrafast carrier recovery time and broadband optical response range. However, the potential application of VSe2 in the field of ultrafast photonics has not been fully developed so far. In this work, the as-prepared VSe2 nanosheets were deposited on tapered fiber by optical deposition to obtain VSe2 SA. By inserting VSe2 SA into an Er-doped fiber laser, the mode-locked pulses with a central wavelength of 1574.4 nm can be obtained. The pulse width of the laser is measured to be ∼680 fs which is narrowest in the reported VSe2 SA-based lasers. In addition, the unique dual-wavelength mode-locked pulse is also obtained by further adjusting intracavity dispersion and polarization. This kind of dual-wavelength pulse is valuable in high order harmonic generation enhancement, terahertz wave generation, dense wavelength division multiplexing, dual-frequency comb and other applications. Our results show that metallic VSe2 is of great potential value in ultrafast fiber laser.

Optimizing High Data Rate Up to 2.5 Tbps Transmission using 64-Channel DWDM System with DCF and NRZ Modulation

Objectives: This study aims to enhance and optimize a modern communication system for high data rate transmission using Dense Wavelength Division Multiplexing (DWDM). The objectives include employing a 64-channel DWDM system, implementing different data speeds, and utilizing a dispersion compensation method. Methods: To achieve the objectives, we simulate and analyze the effects of Dispersion Compensation Fiber (DCF) in a DWDM system with 64 channels. The system employs Non-Return-to-Zero (NRZ) modulation format at varied bit rates and multiple energy levels. We propose a method for achieving data rates of 10 to 40 Gbps using NRZ modulation and Erbium-Doped Fiber Amplifier (EDFA) over a single-mode fiber transmission distance of 40 to 160 km, along with a dispersion compensation fiber of 8 to 32 km (DCF). The performance of the developed model is evaluated based on Quality Factor, Bit Error Rate (BER), Eye Height, and Threshold. These metrics are measured at two input energy levels from an optical power source, covering a communication capacity ranging from 0.625 Tbps to 2.5 Tbps. Findings: Through the simulations and analyses, we uncover the impact of dispersion and demonstrate the effectiveness of the proposed method in compensating for dispersion effects. Performance analysis of two different input transmitter power levels, -10 dBm is more efficient compared to 0 dBm input transmitter power in terms of bit error rate and quality factor. Novelty: This study presents a novel approach to improving modern communication systems by utilizing DWDM with a dispersion compensation method. The use of a 64-channel DWDM system, combined with the proposed NRZ modulation technique and dispersion compensation fiber, provides an efficient solution for achieving high data rates over long transmission distances while minimizing the effects of dispersion. The findings contribute to the advancement of communication systems for high data rate transmission. Keywords Dispersion effect, Bit Error Rate, Q-factor, Optisystem software, Erbium doped fiber amplifier

Analysis the flat gain/noise figure using RAMAN-Reflective Semiconductor Hybrid Optical Amplifier in C + L + U triple band for super dense wavelength division multiplexing system

Abstract Nonlinearity, flat gain and noise figure are the prime concern for super dense wavelength division multiplexing (SD-WDM) systems which have been resolved from RAMAN-RSOA hybrid optical amplifier (HOA) for the first time in this paper. Channel capacity is taken up to 400 with data rate of 10 Gbps. Performances are evaluated with respect to C + L + U band for 1520–1680 nm and 1520 to 1640 nm. RSOA is operated at 40–120 mA bias current to attain best rating flat gain of 34.07 dB with variation of 3.5 dB than the others HOAs (RAMAN-EDFA, RAMAN-SOA and EDFA-SOA). Moreover, the impact of EDFA-SOA is not acceptable in terms of noise figure for SD-WDM optical communication system.

Performance analysis of a hybrid optical amplifier based 480-Gbps DWDM-FSO system under the effect of different atmospheric conditions

Free space optical (FSO) systems offer a desirable and affordable way of providing communication services in remote locations. They provide secure wireless transmission without the requirement for licensing and with lower implementation costs. However, due to the impact of atmospheric turbulences on the effectiveness of FSO systems, their implementation faces significant challenges. Dense wavelength division multiplexing (DWDM) has shown promise in addressing the growing bandwidth needs in optical networks. This paper introduces a hybrid optical amplifier based system, combining DWDM and FSO technology. Energy conservation in such a system involves optimizing various aspects to reduce power consumption while maintaining or improving performance. The proposed DWDM-FSO system operates at a rate of 480 Gbps and consists of 12 channels, each capable of transmitting data at 40 Gbps. The system's performance is evaluated and compared by determining the Q-factor and bit error rate (BER) for both the cases when hybrid amplifier is employed and with no hybrid amplifier within the C-band, specifically focusing on wavelengths around 1550 nm. Moreover, the length of the FSO link is increased to assess the corresponding Q-factor and BER. Resultantly, the maximum distance for the FSO link is determined, ensuring that it remains within acceptable Q-factor and BER thresholds. Furthermore, the FSO system's effectiveness is assessed and compared across various atmospheric conditions. The findings reveal that, in clear weather conditions, the FSO system achieves a maximum distance of 510 meters while maintaining satisfactory Q-factor and BER values when not utilizing a hybrid amplifier. However, by integrating a hybrid amplifier, the system's reach significantly extends to 1700 m under clear weather conditions, still maintaining acceptable Q-factor and BER values.

Coding techniques for diversity enhancement of dense wavelength division multiplexing MIMO‐FSO fault protection protocols systems over atmospheric turbulence channels

AbstractAn enhanced transmission is presented in a multiple‐input‐multiple‐output (MIMO) dense‐wavelength division multiplexed (DWDM) free‐space‐optical (FSO) communication link using diversity coding techniques under the effect of turbulent weather phenomenon. The findings show good performance with an (8 channels × 2.5 Gbps data rate/channel) 20 Gbps 1500 m transmission distance. The bit‐error‐rate (BER), outage probability (OP), and signal‐to‐noise ratio (SNR) of the diversity combining techniques using maximum‐ratio combining (MRC), selection combining (SC), and equal‐gain combining (EGC) technique are evaluated in this work. The obtained results illustrate that Alamouti, space‐time coding (STC), space‐time block coding (STBC), space‐time trellis code (STTC), orthogonal STBC (O‐STBC), and quasi‐orthogonal STBC (QO‐STBC) on the minimum mean‐square‐error, and MRC are worth implementing on the DWDM‐FSO wireless communication systems. The mitigation of atmospheric turbulence is achieved using MIMO diversity combining techniques coding. The simulation results for diversity coding techniques using QO‐STBC/STTC and SC/MRC in the MIMO‐DWDM FSO communication system can improve BER performance, OP, and SNR. The MRC exhibits the lowest OP and BER when compared with the SC and EGC. The numerical results demonstrate that the FSO communication link using DWDM QO‐STBC/STTC improves the power penalty at both BER values under varying atmospheric turbulence conditions for ST, MT, and WT, in comparison to FSO systems without DWDM QO‐STBC/STTC diversity coding techniques.

Performance Analysis of Subcarrier Index Modulation OFDM in a DWDM-FSO link

Free Space Optics (FSO) is a wireless optical communication system using light to establish high-capacity links between points without the need for physical cables. However, its susceptibility to atmospheric conditions such as fog, rain, and turbulence presents challenges to signal quality maintenance. To address this, Dense Wavelength Division Multiplexing (DWDM), traditionally employed in fiber optics, is leveraged to optimize bandwidth utilization and scalability in high-capacity communications. The integration of DWDM into FSO systems offers redundancy and resilience against signal degradation induced by atmospheric conditions. To the best of our knowledge, this is the first time a paper explores the performance of the Subcarrier Index Modulation Orthogonal Frequency Division Multiplexing (SIM-OFDM) technique within a DWDM-FSO system. The objective is to reinforce FSO link robustness and improve transmission rates. Through a comparative analysis with conventional OFDM in an Additive White Gaussian Noise (AWGN) channel, the study reveals a notable Signal-to-Noise Ratio (SNR) gain of at least 3dB with enhanced SIM-OFDM (ESIM-OFDM). Simulations, conducted with realistic parameters within the DWDM-FSO architecture, demonstrate that ESIM-OFDM modulation enables a transmission range of 2 km with an aggregated rate of 10.1 Gb/s. These results underscore the potential of SIM-OFDM in enhancing FSO system performance through the integration of DWDM technology. The proposed ESIM-OFDM DWDM-FSO scenario could represent a highly interesting solution for establishing 5G Backhaul links.

High-speed reach-extended IM-DD system with low-complexity DSP for 6G fronthaul [Invited

With the rising traffic demand from the metaverse, holographic communications, and so on, in beyond-5G (B5G)/6G cloud radio access networks (C-RANs), fronthaul (FH) networks that transport radio information between antennas and distributed/central units will become increasingly demanding. Optical technologies are indispensable in supporting 6G FH deployment, which needs to be high-speed and power/cost-effective simultaneously; low latency is also crucial. This work is extended from our invited paper at OFC2023. While the conference version focused on the wired-wireless conversion/converging side [e.g., using digital signal processing (DSP)-enhanced radio-over-fiber (RoF) techniques] of FH, this work contributes to the complementary side, i.e., optical transmission techniques. Considering 6G capacity and cost requirements, beyond-200-Gb/s/λ optics based on intensity-modulation direct-detection (IM-DD) PAM4 and low-complexity DSP are targeted, which transparently support digital RoF techniques like analog-to-digital-compression (ADX)-RoF (split Option 8) or Delta-sigma RoF, and other functional split options. On the other hand, while the reach of 5G FH may be around 10 km, in 6G FH routing and/or rural connectivity cases, distance can be extended to 20 km or even 40 km. In these scenarios, fiber dispersion in the C-band and even edge wavelengths of the O-band pose a significant challenge for the reach extension of 200G IM-DD systems. We validate through extensive experiments the efficient FH reach extension and dispersion mitigation based on a low-complexity optoelectronic feedforward equalization (OE-FFE) technique. We experimentally verify 224 Gb/s single-wavelength and dense WDM transmissions over up to 41 km distances in the challenging C-band with lean digital equalizers and hard-decision forward error correction (HD-FEC), which are among the first demonstrations to our knowledge. Even with split Option 8 and extended reach, the FH systems support up to a 10 Tb/s Common Public Radio Interface (CPRI)-equivalent rate and >300Gb/s peak wireless data rate. The presented systems can be useful for high-capacity, reach-extended FH scenarios toward 6G.

Submicrometer optical frequency combs based on SPPs metallic multi-ring resonators

Optical frequency combs (OFCs) have great potential in communications, especially in dense wavelength-division multiplexing. However, the size of traditional OFCs based on conventional optical microcavities or dispersion fibers is at least tens of micrometers, far larger than that of nanoscale electronic chips. Therefore, reducing the size of OFCs to match electronic chips is of necessity. Here, for the first time to our knowledge, we introduce surface plasmon polaritons (SPPs) to the construction of OFCs to realize a miniature device. The thickness of our device is reduced below 1 μm. Though the presence of SPPs may induce ohmic and scattering loss, the threshold of the device is obtained as 9 μW, comparable to the conventional device. Interestingly, the response time is 13.2 ps, much faster than the optical counterparts. This work provides a feasible strategy for the miniaturization of OFCs.

Implementation and evaluation of two parallel computational models for the simulation of a long‐haul DWDM system limited by FWM

AbstractFour‐Wave Mixing (FWM) is one of the non‐linear phenomena affecting long‐reach communication systems and high bandwidth. Research communities use simulation tools for parameter optimization. Unfortunately, such a simulation is time‐consuming and requires more time as the number of channels increases. This paper proposes two fast implementations of Dense Wavelength Division Multiplexing (DWDM) system, limited by FWM and the intrinsic Amplified Spontaneous Emission (ASE) noise of optical amplifiers employed in each segment. Additionally, this work compares the efficiency and speed improvement of the proposed parallelization model versus an earlier sequential model. We present the computational complexity analysis of sequential and parallel models. The paper considers two different parallel implementations: a multicore processor using Open MultiProcessing (OpenMP) and Compute Unified Device Architecture (CUDA), which is based on the use of a Graphics Processing Unit (GPU). Results show that parallelism using CUDA improves by up to 70 times the simulation performance compared to the sequential model. Parallelism with CUDA is up to 15 times compared to OpenMP using 12 logical processors. It is possible to simulate an increased number of channels within our parallel execution, which was impractical in the sequential simulation.

Optimization Method for Center Frequency Accuracy of High-Channel-Count Arrayed Waveguide Grating in Dense Wavelength Division Multiplexing Systems

The arrayed waveguide grating (AWG) is an essential component in dense wavelength division multiplexing (DWDM) systems. With advancements in optical communication technology, the number of AWG output channels has rapidly increased. However, achieving high center frequency accuracy (CFA) for these channels has become a significant challenge. This paper presents a design and optimization approach for a high-channel-count AWG based on the silica platform and the finite difference beam propagation method (FD-BPM). The causes of center frequency deviation are analyzed, and an optimization method is proposed to adjust the constraint relationship and geometric position of the output waveguides in order to improve CFA. Simulation results demonstrate the excellent optical performance of the designed AWG, achieving a CFA of up to 0.04 times the output channel frequency spacing. The insertion loss, insertion loss uniformity, and adjacent output channel crosstalk are simulated as 1.51 dB, 0.38 dB, and 23.81 dB, respectively. The optimized CFA could compensate for center frequency deviations caused by manufacturing errors and temperature fluctuations. The findings of this research hold potential for extending the optimization to other material platforms and contributing to the development of DWDM systems in the field of optical communication.

Double-Brillouin Frequency Spacing Multi-Wavelength Brillouin Erbium Fiber Laser in Double Cavities Configuration

Multi-wavelength fiber laser has great potential for use in dense wavelength-division multiplexing (DWDM) systems, sensors, and microwave photonics. This paper presents a multi-wavelength Brillouin erbium fiber laser (MW-BEFL) with double-frequency Brillouin spacing of approximately 0.176 nm between each adjacent Stokes. The proposed setup utilizes double cavities configuration for odd and even-order Brillouin Stokes to propagate separately in the system. This configuration is flexible as it can be transformed into a single-spacing MW-BEFL by swapping the ports of the circulator; it can also extract the odd-orders Brillouin Stokes by relocating the OSA in the cavity. Up to 25 double-spaced Brillouin Stokes are obtained with a tuning range of 30 nm. The first 8 Stokes have peak power variation within ± 3.7 dB and an average signal-to-noise ratio of 20 dB.

Design of Ultra Dense WDM Optical Communication System to Reduce Signal Impairments Using DCF and Repeater Techniques

Linear and non-linear impairments are the major problems that affected the dense wavelength division multiplexing (DWDM) system performance. In this simulation designs, two different compensation techniques have been proposed to eliminate signal impairments. The repeater technique was proposed to reduce non-linear effects like four-wave mixing (FWM) which cause transfer power from DWDM channels to another new channels. The dispersion compensation fiber (DCF) technique was used to reduce dispersion effects which cause signal pulse broadening over long transmission distances. Also, three different modulation formats and four frequency separations were used to determine which modulation scheme is more compatible with the compensation techniques. The results is calculated in term of quality factor against power and noetic that the carrier suppressed return to zero (CSRZ) format offers the best performance with the DCF technique with 32.1804 Q-factor at 15dBm threshold power then, the differential phase shift keying (DPSK) format is compatible with the repeater technique with 27.7959 quality factor and 14dBm threshold power. Index Terms— Dense Wavelength Division Multiplexing (DWDM), Dispersion Compensation Fiber DCF, Repeater, and Non-linear Effects.

Low-Complexity Conditional Generative Adversarial Network (c-GAN) Based Nonlinear Equalizer for Coherent Data-Center Interconnections

Nonlinear impairments emerging from both fiber optical links and optoelectrical devices are the major bottleneck for enhancing the throughput of photonic data-center interconnection (DCI). Here, we propose a data-driven nonlinear equalizer based on a conditional generative adversarial network (c-GAN) for high-speed and large-capacity photonic DCI. Its performance is experimentally evaluated by transmitting C-band 40-channel 60-GBaud dual polarization-16 quadrature amplitude modulation (DP-16QAM) dense wavelength division multiplexing (DWDM) signals over 20-km standard single-mode fiber (SSMF). Our experimental results verify that, the proposed c-GAN equalizer outperforms both traditional nonlinear equalizers and other data-driven counterparts, in terms of both the bit-error ratio (BER) and computational complexity. Only the proposed c-GAN equalizer can guarantee the BER performance of all 40 channels to reach the threshold of 20% soft decision forward error correction (SD-FEC) at BER=0.027, leading to a net transmission capacity of 16 Tb/s. Meanwhile, the computational complexity of the proposed c-GAN equalizer can be significantly reduced by 31.8%, 80.7%, and 98.8%, respectively, in comparison with Volterra filter equalizer (VFE), multilayer perceptron (MLP), and long short-term memory neural network (LSTM-NN) schemes.

Hybrid amplifier placement in mesh DWDM networks using integer linear programming models

Hybrid erbium-doped fiber (EDF)/Raman amplifiers (HFAs) can be utilized to improve the performance of specific fiber spans in dense wavelength division multiplexing (DWDM) networks, aiming to extend the reach and/or increase the capacity of optical channels, thereby reducing the total number of line interfaces required to satisfy a given set of traffic demands. However, HFAs are costlier than simpler EDF amplifiers (EDFAs) since they include Raman pumps in addition to an EDFA. Consequently, it is paramount to place them only at selected fiber spans of the network so as to maximize their impact while keeping their number limited. It has been shown that HFA placement can be a complex task in mesh DWDM networks in view of optical channel diversity, with each fiber span traversed by multiple channels with different source and destination nodes. Building on the approximation that noise adds up incoherently along the transmission path, this paper proposes optimal methods to solve the problem of placing hybrid amplifiers in mesh networks. Particularly, it describes two integer linear programming models, one to determine the minimum number and location of HFAs required to reach a target set of feasible optical channels (i.e., without intermediate 3R regenerators) and another to maximize the number of feasible optical channels given a limited number of HFAs to be deployed. A comprehensive set of network simulations using three reference optical network topologies is reported, providing insight into the effectiveness of the proposed models when compared to existing approaches.

In-band full-duplex multiband mobile fronthaul network based on analog radio-over-fiber andtandem SSB modulation.

An in-band full-duplex multiband mobile fronthaul network is proposed based on analog radio-over-fiber and tandem single-sideband (TSSB) modulation. Two optical carriers with a wavelength spacing of 50GHz in accordance with international telecommunication union dense wavelength division multiplexing (DWDM) standards are employed in each distributed unit (DU): one is used to carry two different radio frequency (RF) vector signals at 3 and 10GHz, while the other is used to carry a vector signal at 15GHz and a single-tone signal at 15GHz. At the DU, a parallel TSSB modulation is applied, which eliminates the cross talk of TSSB modulation through two dual-polarization binary phase-shift keying (DP-BPSK) modulators. This allows the two vector signals carrying different data to be distributed on both sides of the optical carrier. At the active antenna unit (AAU), different RF vector signals centered at 3, 30, and 60GHz, each carrying distinct information, can be generated by selecting either one DWDM channel or two adjacent DWDM channels in a group. By utilizing the spacing between the two DWDM optical carriers, millimeter-wave signals can be generated without the need for additional electronic upconversion devices in the AAU. In the uplink, a DP-BPSK modulator is used to receive the signal of interest while canceling self-interference. Simulation results demonstrate the performance of the proposed system. After transmitting 25km through single-mode fiber and compensating for dispersion using corresponding dispersion-compensating fiber, the downlink and uplink achieve error vector magnitudes of less than 9% and 2%, respectively, when the receiving optical power is 6dBm.

Robust traffic grooming and infrastructure placement in OTN-over-DWDM networks

The advent of next-generation networks has revolutionized modern networking practices through its improved service capability as well as its numerous emerging use cases. Coupled with the increasing number of connected devices, 5G and beyond (5G+) network traffic is expected to be increasingly diverse and high in volume. To address the large amount of data exchanged between the 5G+ core and external data networks, optical transport networks (OTNs) with dense wavelength-division multiplexing (DWDM) will be leveraged. In order to prepare for this increase in traffic, network operators (NOs) must develop and expand their existing backbone networks, requiring significant levels of capital expenditures. To this end, the traffic grooming and infrastructure placement problem is critical to supporting NO decisions. The work presented in this paper considers the traffic grooming and infrastructure placement problem for OTN-over-DWDM networks. The dynamicity and diversity of 5G+ network traffic are addressed through the use of robust optimization, allowing for increasing levels of solution conservativeness to protect against various levels of demand uncertainty. Furthermore, a robust traffic grooming and infrastructure placement heuristic (RGIP-H) solution capable of addressing the scalability concerns of the optimization problem formulation is presented. The results presented in this work demonstrate how the tuning of the robust parameters affects the cost of the objective function. Additionally, the ability of the robust solution to protect the solution under demand uncertainty is highlighted when the robust and deterministic solutions are compared during parameter deviation trials. Finally, the performance of the RGIP-H is compared to the optimization models when applied to larger network sizes.

Electro-optical tunable interleaver in hybrid silicon and lithium niobate thin films.

The interleaver was one of the key devices in dense wavelength division multiplexing (DWDM) applications. In this study, an interleaver with an asymmetrical Mach-Zehnder interferometer structure was designed, fabricated, and characterized in hybrid silicon and lithium niobate thin films (Si-LNOI). The interleaver based on Si-LNOI could be fabricated by mature processing technology of Si photonic, and it was capable of the electro-optical (E-O) tuning function by using the E-O effect of LN. In the range of 1530-1620 nm, the interleaver achieved a channel spacing of 55 GHz and an extinction ratio of 12-28 dB. Due to the large refractive index of Si, the Si loading strip waveguide based on Si-LNOI had a compact optical mode area, which allowed a small electrode gap to improve the E-O modulation efficiency of the interleaver. For an E-O interaction length of 1 mm, the E-O modulation efficiency was 26 pm/V. The interleaver will have potential applications in DWDM systems, optical switches, and filters.

Optical label-based cost-effective DWDM optical network performance monitoring using low-bandwidth PD with novel SRS mitigation DSP

Large-scale dense wavelength division multiplexing (DWDM) multi-channel performance monitoring is one of the indispensable technologies for the flexible optical networks. The existing Labelbased monitoring scheme requires expensive optical demultiplexing components/equipment to avoid the influence of stimulated Raman scattering (SRS), which is not only costly and bulky, but also could not monitor the wavelength channels simultaneously. In this paper, a low-cost, high-accuracy monitoring scheme based on Optical Label Method is proposed for DWDM networks, where the optical channel power and node identification (ID), as the main monitoring targets that both can indicate or evaluate the channel connection status, could be efficiently monitored. In the scheme, a novel digital signal processing (DSP) method of SRS mitigation is proposed and demonstrated, and an asynchronous code-division multiple access (A-CDMA) based digital label encoding and decoding method is adopted to distinguish the node ID so that channel initial added node can be accurately verified, thereby wavelength connection status can be reliably monitored by combining the channel power and node ID information. The simulation results show that each wavelength channel power and node ID can be accurately monitored only by low bandwidth photoelectric detector (PD) under the condition of 80 wavelengths and 10 spans at C-band.