Degradable Crosslinker Research Articles

Synthesis and Solvent Free DLP 3D Printing of Degradable Poly(Allyl Glycidyl Ether Succinate).

Digital light processing (DLP) printing forms solid constructs from fluidic resins by photochemically crosslinking polymeric resins with reactive functional groups. DLP is used widely due to its efficient, high-resolution printing, but its use and translational potential has been limited in some applications as state-of-the-art resins experience unpredictable and anisotropic part shrinkage due to the use of solvent needed to reduce resin viscosity and layer dependent crosslinking. Herein, poly(allyl glycidyl ether succinate) (PAGES), a low viscosity, degradable polyester, was synthesized by ring opening copolymerization and used in combination with degradable thiol crosslinkers to afford a solvent free resin that can be utilized in DLP printing. Varying resin formulations of PAGES polymer are shown to decrease part shrinkage from 14 % to 0.3 %. Photochemically printed parts fabricated from PAGES possess tensile moduli between 0.43 and 6.18 MPa and degradation profiles are shown to vary between 12 and 40 days under accelerated conditions based on degree of polymerization and crosslink ratio.

Synthesis and Solvent Free DLP 3D Printing of Degradable Poly(Allyl Glycidyl Ether Succinate)

AbstractDigital light processing (DLP) printing forms solid constructs from fluidic resins by photochemically crosslinking polymeric resins with reactive functional groups. DLP is used widely due to its efficient, high‐resolution printing, but its use and translational potential has been limited in some applications as state‐of‐the‐art resins experience unpredictable and anisotropic part shrinkage due to the use of solvent needed to reduce resin viscosity and layer dependent crosslinking. Herein, poly(allyl glycidyl ether succinate) (PAGES), a low viscosity, degradable polyester, was synthesized by ring opening copolymerization and used in combination with degradable thiol crosslinkers to afford a solvent free resin that can be utilized in DLP printing. Varying resin formulations of PAGES polymer are shown to decrease part shrinkage from 14 % to 0.3 %. Photochemically printed parts fabricated from PAGES possess tensile moduli between 0.43 and 6.18 MPa and degradation profiles are shown to vary between 12 and 40 days under accelerated conditions based on degree of polymerization and crosslink ratio.

Abstract 305: Bioinspired synthetic hydrogel in pancreatic cancer organoid matrix modeling

Abstract Background: Pancreatic ductal adenocarcinoma (PDAC) is a leading cause of cancer mortality with a primary hallmark, including dense collagen matrix in the desmoplastic stroma. Organoid technologies often rely on commercially available EHS mouse sarcoma matrix materials, and it remains uncertain how batch-to-batch variability of this matrix impacts the consistency of cancer signaling. Here, we present a novel photo-activated hydrogel tuned to the properties of the desmoplastic stroma in PDAC organoid cultures. Method: We designed multiple synthetic hydrogel materials with tunable mechanical properties, including SP-139 (Stem Pharm, Inc), a polyethylene glycol-based hydrogel functionalized with norbornene and formed with both degradable and non-degradable crosslinking peptides and a cell adhesion peptide (CRGDS). We used rheometry to measure the elastic modulus of the polymerized hydrogel after visible light photoactivation (395 nm) and expanded multiple cancer organoid cultures. RNAseq was performed from patient-derived xenografts to expanded organoids across matrix designs (Cultrex® v. SP-139) and analyzed by GSVA pathway analyses. Result: We optimized the ratio of non-degradable v. degradable crosslinking peptide to support culture expansion and enzymatic digestion with dispase II (125 µg/mL) and collagenase II (1 mg/mL). Using rheometry, SP-139 at 75% v/v had increased elastic modulus versus Cultrex RGF BME matrix Type 2 at 100% v/v (4992±76.3 v. 68.4±5.6 Pa, p<0.0001). Phenotypic growth was confirmed across serial passages (>8) and a diversity of gastrointestinal cancer types (n=5). Baseline growth rates were identical over 48h between SP-139 (75% v/v) and Cultrex (50% v/v) (+13.4% v. +13.0, p=0.75). Growth remained consistent for SP-139 yet increased with Cultrex at interval of 48-96h (+12.9% SP-139 v +22.4% Cultrex, p<0.005) and interval of 96-144h (+13.6% SP-139 v +24.0% Cultrex®, p<0.0001). Therapeutic response was assessed using 3D CellTiter-Glo® using gemcitabine 100 µM (24h) with comparable inhibition of normalized cell viability in SP-139 v. Cultrex® (35.4±1.9% v. 52.3±6.5%, n.s.) and qualitatively with viability staining using calcein AM and Caspase 3/7FITC. RNAseq revealed Cultrex, when compared to SP-139, yielded down regulation of epoxygenase p450 pathways (padj<0.012) and negative regulation of the p38 MAP kinase cascade (padj<0.048). Conclusions: Functionalized PEG-based synthetic hydrogel matrix materials can be tuned for physical properties to mimic cancer tissue microenvironments more accurately. SP-139, designed to mimic the desmoplastic stroma of the pancreatic cancer microenvironment, has favorable properties including controlled growth rates and compatibility with high content imaging by luminescence and fluorescence. RNAseq pathway analysis shows SP-139 maintains pathways of p450 and MAP kinase signaling of importance with therapeutic resistance. Citation Format: Md Shahadat Hossan, Austin Stram, Ethan Samuel Lin, Sean McIlwain, Connie Lebakken, William Richards, Jeremy D. Kratz. Bioinspired synthetic hydrogel in pancreatic cancer organoid matrix modeling [abstract]. In: Proceedings of the American Association for Cancer Research Annual Meeting 2024; Part 1 (Regular Abstracts); 2024 Apr 5-10; San Diego, CA. Philadelphia (PA): AACR; Cancer Res 2024;84(6_Suppl):Abstract nr 305.

Recycling of Epoxy Resins with Degradable Structures or Dynamic Cross-Linking Networks: A Review

Recycling of Epoxy Resins with Degradable Structures or Dynamic Cross-Linking Networks: A Review

Differentiation, maturation, and collection of THP-1-derived dendritic cells based on a PEG hydrogel culture platform

PurposeDendritic cell (DC) is a spearhead responsible for immune response and surrounded by extracellular matrix in three-dimensional (3D) tissue. Nevertheless, conventional DC culture has relied on suspension or two-dimensional (2D) tissue culture plate (TCP)-based culture system. This culture condition often fails to recapitulate the physiological behavior of DC in real tissue. In this work, the effect of culture condition on DC physiology was explored with varying 3D hydrogel property (i.e., degradability, adhesion, and stiffness). In particular, DC differentiation and maturation in 3D were evaluated comparing the conventional TCP-based culture condition.MethodTHP-1 cells were encapsulated in poly(ethylene glycol) (PEG) hydrogel via thiol-ene photocrosslinking with non-degradable or proteolytically degradable peptide crosslinker. Hydrogel stiffness was manipulated by controlling the concentration of crosslinker. The metabolic activities and cytotoxicity of the encapsulated cells were measured by resazurin and Live/Dead assays, respectively. Cell harvesting was conducted via enzymatic degradation using α-chymotrypsin, and differentiation and maturation of the liberated DCs were evaluated by quantitative polymerase chain reaction and flow cytometry.ResultsTHP-1 cells well proliferated in the soft degradable hydrogel with a higher metabolic activity. However, the stiff matrix inhibited cell growth in 3D. The gene expression assay indicated that the 3D hydrogel condition was superior to 2D culture in terms of differentiation and maturation of DC. Interestingly, the stiffness of matrix was important factor in DC function. In the stiff hydrogel, the expression levels of differentiation and maturation markers were higher compared to the low stiffness hydrogel. The mature DCs caged in the hydrogel matrix were harvested after short enzymatic digestion of hydrogel and the liberated cells had over 90% viability. The flow cytometric result revealed that the proportion of CD80 + /CD86 + cells from the stiff hydrogel was relatively higher than cells either from 2D or soft hydrogel in 3D.ConclusionThe collected evidence indicated that the proteolytically degradable PEG hydrogel matrix promoted DC differentiation and maturation. In addition, the matrix stiffness control could manipulate the marker expressions of differentiation and maturation. Particularly, the mature DC was successfully collected from the hydrogel matrix. These results highlighted the PEG hydrogel-based DC culture might be a useful tool for potential DC-based immunotherapies.

A 4D Printed Adhesive, Thermo-Contractile, and Degradable Hydrogel for Diabetic Wound Healing.

Chronic wound healing remains a substantial clinical challenge. Current treatments are often either prohibitively expensive or insufficient in meeting the various requirements needed for effective diabetic wound healing. A 4D printing multifunctional hydrogel dressing is reported here, which aligns perfectly with wounds owning various complex shapes and depths, promoting both wound closure and tissue regeneration. The hydrogel is prepared via digital light process (DLP) 3D printing of the mixture containing N-isopropylacrylamide (NIPAm), curcumin-loaded Pluronic F127 micelles (Cur-PF127), and poly(ethylene glycol) diacrylate-dopamine (PEGDA575-Do), a degradable crosslinker. The use of PEGDA575-Do ensures tissue adhesion and degradability, and cur-PF127 serves as an antibacterial agent. Moreover, the thermo-responsive mainchains (i.e., polymerized NIPAm) enables the activation of wound contraction by body temperature. The features of the prepared hydrogel, including robust tissue adhesion, temperature-responsive contraction, effective hemostasis, spectral antibacterial, biocompatibility, biodegradability, and inflammation regulation, contribute to accelerating diabetic wound healing in Methicillin-resistant Staphylococcus aureus (MRSA)-infected full-thickness skin defect diabetic rat models and liver injury mouse models, highlighting the potential of this customizable, mechanobiological, and inflammation-regulatory dressing to expedite wound healing in various clinical settings.

Development of Novel Delayed Swelling Polymer Gel Particles with Salt Resistance for Enhanced In-Depth Permeability Control

Summary Prolonged waterflooding or polymer flooding in oil fields often exacerbates reservoir heterogeneity, leading to premature water breakthrough and high water cut, which significantly hinders efficient oilfield development. To address this issue, polymer gel particles have been prescribed to enhance sweep efficiency and augment waterflooding recovery by plugging preferential pathways within the reservoir. However, inherent weaknesses of polymer gel particles, such as fast water absorption and expansion rates in the initial stage and low post-expansion rates, make it difficult to balance in-depth transportation and plugging performance. Additionally, these gel particles are sensitive to ions in the formation water, resulting in reduced expansion rates under high-salinity conditions. Therefore, there are still challenges in the application of polymer gel particles for in-depth permeability control. In this study, a new type of delayed swelling and salt-resistant polymer gel particle was synthesized through inverse emulsion copolymerization. To achieve delayed swelling, we use a degradable crosslinker and hydrophobic monomer to enhance the crosslinked network density and hydrophobicity of gel particles. Our double crosslinked gel particles keep their original size until Day 2, then gradually swell up to 20 days in NaCl solution with a concentration of 15×104 mg·L−1 at 90°C. In comparison, the traditional single crosslinked gel particles show significant disparities in swelling behaviors and quickly swell when just dispersed in a 15×104 mg·L−1 NaCl solution at 90°C, maintaining roughly the same size over the testing period. Coreflooding experiments demonstrate that the residual resistance before and after aging increases from 2.37 to 6.82. The newly synthesized delayed swelling and salt-resistant polymer gel particles exhibit promising potential for overcoming the challenges associated with reservoir heterogeneity and high salinity.

Cross-linking polybutadiene rubber via a thiol-ene reaction with polycysteine as a degradable cross-linker

Covalently cross-linked rubber materials are widely used in elastic applications due to their excellent mechanical properties. However, the irreversibility of covalent cross-linking suffers from poor material recyclability. As a degradable polypeptide-based cross-linker for polybutadiene, poly(l-cysteine) (polyCys) was synthesized via papain-catalyzed chemoenzymatic polymerization. The resulting polyCys had intact thiol groups that cross-linked polybutadiene via the thiol-ene reaction. The cross-linking reaction of polybutadiene was performed in the presence of polyCys and a radical initiator and resulted in insoluble polybutadiene gel formation. Based on Raman spectroscopy analysis, the cross-linking reaction was confirmed by the consumption of thiol groups of polyCys. From the dynamic viscoelastic analyses of the cross-linked polybutadienes, the viscoelasticity drastically changed from that of raw polybutadiene, with the disappearance of the slow relaxation mode at low frequencies. The complete network formation was confirmed by E′ and E′′ showing the power law over the whole frequency range, as determined by the time-course experiments of the dynamic viscoelastic properties. The cross-linked polybutadiene was degradable by acid hydrolysis, resulting in the regeneration of soluble polybutadiene. Polypeptide cross-linked polybutadiene materials are promising candidates for the application of polybutadiene-based rubber materials with the requirements of both material integrity and reusability.

Site-oriented conjugation of poly(2-methacryloyloxyethyl phosphorylcholine) for enhanced brain delivery of antibody.

Antibody therapeutics are limited in treating brain diseases due to poor blood-brain barrier (BBB) penetration. We have discovered that poly 2-methacryloyloxyethyl phosphorylcholine (PMPC), a biocompatible polymer, effectively facilitates BBB penetration via receptor-mediated transcytosis and have developed a PMPC-shell-based platform for brain delivery of therapeutic antibodies, termed nanocapsule. Yet, the platform results in functional loss of antibodies due to epitope masking by the PMPC polymer network, which necessitates the incorporation of a targeting moiety and degradable crosslinker to enable on-site antibody release. In this study, we developed a novel platform based on site-oriented conjugation of PMPC to the antibody, allowing it to maintain key functionalities of the original antibody. With an optimized PMPC chain length, the PMPC-antibody conjugate exhibited enhanced brain delivery while retaining epitope recognition, cellular internalization, and antibody-dependent cellular phagocytic activity. This simple formula incorporates only the antibody and PMPC without requiring additional components, thereby addressing the issues of the nanocapsule platform and paving the way for PMPC-based brain delivery strategies for antibodies.

Hydrogel degradation promotes angiogenic and regenerative potential of cell spheroids for wound healing.

Chronic nonhealing wounds are debilitating and diminish one's quality of life, necessitating the development of improved strategies for effective treatment. Biomaterial- and cell-based therapies offer an alternative treatment compared to conventional wound care for regenerating damaged tissues. Cell-based approaches frequently utilize endothelial cells (ECs) to promote vascularization and mesenchymal stromal cells (MSCs) for their potent secretome that promotes host cell recruitment. Spheroids have improved therapeutic potential over monodisperse cells, while degradable scaffolds can influence cellular processes conducive to long-term tissue regeneration. However, the role of biomaterial degradation on the therapeutic potential of heterotypic EC-MSC spheroids for wound healing is largely unknown. We formed poly(ethylene) glycol (PEG) hydrogels with varying ratios of matrix metalloproteinase (MMP)-degradable and non-degradable crosslinkers to develop three distinct constructs - fully degradable, partially degradable, and non-degradable - and interrogate the influence of degradation rate on engineered cell carriers for wound healing. We found that the vulnerability to degradation was critical for cellular proliferation, while inhibition of degradation impaired spheroid metabolic activity. Higher concentrations of degradable crosslinker promoted robust cell spreading, outgrowth, and secretion of proangiogenic cytokines (i.e., VEGF, HGF) that are critical in wound healing. The degree of degradation dictated the unique secretory profile of spheroids. When applied to a clinically relevant full-thickness ex vivo skin model, degradable spheroid-loaded hydrogels restored stratification of the epidermal layer, confirming the efficacy of scaffolds to promote wound healing. These results highlight the importance of matrix remodeling and its essential role in the therapeutic potential of heterotypic spheroids.

A novel, robust mechanical strength, and naturally degradable double crosslinking starch-based bioplastics for practical applications

The increasing number of petroleum-based plastics has caused severe environmental pollution, which has attracted great research interest in the development of low-cost, renewable, and degradable starch-based bioplastics. However, developing starch-based bioplastics with robust mechanical strength, excellent water resistance, and thermal resistance remains a great challenge. In this study, we presented a simple and efficient method for preparing high-performance novel starch-based bioplastics with chemical and physical double crosslinking network structures filled with 2,2,6,6-tetramethylpiperidine 1-oxy-oxidized cellulose nanofibers and zinc oxide nanoparticles. Compared with pure starch-based bioplastics, the tensile strength of the novel robust strength starch-based bioplastics increased by 431.2 %. The novel starch-based bioplastics exhibited excellent mechanical properties (tensile strength up to 24.54 MPa), water resistance, thermal resistance, and biodegradability. In addition, the novel starch-based bioplastics could be reused, crushed, dissolved, and re-poured after use. After recycling, the novel starch-based bioplastics could be discarded in the soil to achieve complete degradation within six weeks. Owing to these characteristics, the novel starch-based bioplastics are good alternatives used to replace traditional petroleum-based plastics and have great development prospects.

DMTMM-mediated synthesis of norbornene-modified hyaluronic acid polymers to probe cell-hydrogel interactions

Synthesis of chemically modified hyaluronic acid (HA) polymers has enabled the fabrication of hydrogels, such as norbornene-modified HA (NorHA) hydrogels that can provide tunable mechanical properties. However, current protocols for the synthesis of NorHA polymers rely on the use of dimethyl sulfoxide (DMSO), a solvent that is cost-intensive and requires extensive dialysis to be removed. To address this limitation, we developed an organic solvent-free NorHA synthesis protocol based on the triazine derivative 4-(4,6-dimethoxy-1,3,5-triazin-2-yl)-4-methylmorpholinium chloride (DMTMM) which enables control over the degree of substituted norbornene groups and hydrogel mechanical properties. Our study further demonstrates the incorporation of enzymatically degradable crosslinkers to fabricate NorHA hydrogels as an in vitro platform to tune cell spreading and nascent protein deposition towards their use in tissue engineering and regenerative medicine.

Vat Photopolymerization 3D Printing of Hydrogels with Re-Adjustable Swelling.

Vat photopolymerization typically prints highly crosslinked networks. Printing hydrogels, which are also networks but with a high swelling capacity in water and therefore with low crosslinking density, is a challenge for this technique. However, it may be of interest in medicine and in other areas, since it would allow for the preparation of this type of 3D-shaped material. In this work, an approach for printing hydrogels via vat photopolymerization that uses a mixture of stable and hydrolysable crosslinkers has been evaluated so that an initial highly crosslinked network can be printed, although after hydrolysis it becomes a network with low crosslinking. This approach has been studied with PEO/PEG-related formulations, that is, with a PEG-dimethacrylate as a stable crosslinker, a PEO-related derivative carrying β-aminoesters as a degradable crosslinker, and PEG-methyl ether acrylate and hydroxyethyl acrylate as monofunctional monomers. A wide family of formulations has been studied, maintaining the weight percentage of the crosslinkers at 15%. Resins have been studied in terms of viscosity, and the printing process has been evaluated through the generation of Jacobs working curves. It has been shown that this approach allows for the printing of pieces of different shapes and sizes via vat photopolymerization, and that these pieces can re-ajust their water content in a tailored fashion through treatments in different media (PBS or pH 10 buffer).

Modulating design parameters to drive cell invasion into hydrogels for osteochondral tissue formation

BackgroundThe use of acellular hydrogels to repair osteochondral defects requires cells to first invade the biomaterial and then to deposit extracellular matrix for tissue regeneration. Due to the diverse physicochemical properties of engineered hydrogels, the specific properties that allow or even improve the behaviour of cells are not yet clear. The aim of this study was to investigate the influence of various physicochemical properties of hydrogels on cell migration and related tissue formation using in vitro, ex vivo and in vivo models. MethodsThree hydrogel platforms were used in the study: Gelatine methacryloyl (GelMA) (5% wt), norbornene hyaluronic acid (norHA) (2% wt) and tyramine functionalised hyaluronic acid (THA) (2.5% wt). GelMA was modified to vary the degree of functionalisation (DoF 50% and 80%), norHA was used with varied degradability via a matrix metalloproteinase (MMP) degradable crosslinker and THA was used with the addition of collagen fibrils. The migration of human mesenchymal stromal cells (hMSC) in hydrogels was studied in vitro using a 3D spheroid migration assay over 48h. In addition, chondrocyte migration within and around hydrogels was investigated in an ex vivo bovine cartilage ring model (three weeks). Finally, tissue repair within osteochondral defects was studied in a semi-orthotopic in vivo mouse model (six weeks). ResultsA lower DoF of GelMA did not affect cell migration in vitro (p ​= ​0.390) and led to a higher migration score ex vivo (p ​< ​0.001). The introduction of a MMP degradable crosslinker in norHA hydrogels did not improve cell infiltration in vitro or in vivo. The addition of collagen to THA resulted in greater hMSC migration in vitro (p ​= ​0.031) and ex vivo (p ​< ​0.001). Hydrogels that exhibited more cell migration in vitro or ex vivo also showed more tissue formation in the osteochondral defects in vivo, except for the norHA group. Whereas norHA with a degradable crosslinker did not improve cell migration in vitro or ex vivo, it did significantly increase tissue formation in vivo compared to the non-degradable crosslinker (p ​< ​0.001). ConclusionThe modification of hydrogels by adapting DoF, use of a degradable crosslinker or including fibrillar collagen can control and improve cell migration and tissue formation for osteochondral defect repair. This study also emphasizes the importance of performing both in vitro and in vivo testing of biomaterials, as, depending on the material, the results might be affected by the model used.The translational potential of this article: This article highlights the potential of using acellular hydrogels to repair osteochondral defects, which are common injuries in orthopaedics. The study provides a deeper understanding of how to modify the properties of hydrogels to control cell migration and tissue formation for osteochondral defect repair. The results of this article also highlight that the choice of the used laboratory model can affect the outcome. Testing hydrogels in different models is thus advised for successful translation of laboratory results to the clinical application.

Poly(2-hydroxyethyl methacrylate) hydrogels containing graphene-based materials for blood-contact applications: from soft inert to strong degradable material.

Degradable biomaterials for blood-contacting devices (BCDs) are associated with weak mechanical properties, high molecular weight of the degradation products and poor hemocompatibility. Herein, the inert and biocompatible FDA approved poly(2-hydroxyethyl methacrylate) (pHEMA) hydrogel was turned into a degradable material by incorporation of different amounts of a hydrolytically labile crosslinking agent, pentaerythritol tetrakis(3-mercaptopropionate). In situ addition of 1wt.% of oxidized graphene-based materials (GBMs) with different lateral sizes/thicknesses (single-layer graphene oxide, and oxidized forms of few-layer graphene materials) was performed to enhance the mechanical properties of hydrogels. An ultimate tensile strength increases up to 0.2 MPa (293% higher than degradable pHEMA) was obtained using oxidized few-layer graphene with 5 μm lateral size. Moreover, the incorporation of GBMs has demonstrated to simultaneously tune the degradation time, which ranged from 2 to 4 months. Notably, these features were achieved keeping not only the intrinsic properties of inert pHEMA regarding water uptake, wettability and cytocompatibility (short and long term), but also the non-fouling behavior towards human cells, platelets and bacteria. This new pHEMA hydrogel with degradation and biomechanical performance tuned by GBMs, can therefore be envisioned for different applications in tissue engineering, particularly for BCDs where non-fouling character is essential. STATEMENT OF SIGNIFICANCE: Suitable mechanical properties, low molecular weight of the degradation products and hemocompatibility are key features in degradable blood contacting devices (BCDs), and pave the way for significant improvement in the field. In here, a hydrogel with outstanding anti-adhesiveness (pHEMA) provides hemocompatibility, the presence of a degradable crosslinker provides degradability, and incorporation of graphene oxide reestablishes its strength, allowing tuning of both degradation and mechanical properties. Notably, these hydrogels simultaneously provide suitable water uptake, wettability, cytocompatibility (short and long term), no acute inflammatory response, and non-fouling behavior towards endothelial cells, platelets and bacteria. Such results highlight the potential of these hydrogels to be envisioned for applications in tissue engineered BCDs, namely as small diameter vascular grafts.

Understanding the Degradation of Core-Shell Nanogels Using Asymmetrical Flow Field Flow Fractionation.

Nanogels are candidates for biomedical applications, and core-shell nanogels offer the potential to tune thermoresponsive behaviour with the capacity for extensive degradation. These properties were achieved by the combination of a core of poly(N-isopropylmethacrylamide) and a shell of poly(N-isopropylacrylamide), both crosslinked with the degradable crosslinker N,N'-bis(acryloyl)cystamine. In this work, the degradation behaviour of these nanogels was characterised using asymmetric flow field flow fractionation coupled with multi-angle and dynamic light scattering. By monitoring the degradation products of the nanogels in real-time, it was possible to identify three distinct stages of degradation: nanogel swelling, nanogel fragmentation, and nanogel fragment degradation. The results indicate that the core-shell nanogels degrade slower than their non-core-shell counterparts, possibly due to a higher degree of self-crosslinking reactions occurring in the shell. The majority of the degradation products had molecule weights below 10 kDa, which suggests that they may be cleared through the kidneys. This study provides important insights into the design and characterisation of degradable nanogels for biomedical applications, highlighting the need for accurate characterisation techniques to measure the potential biological impact of nanogel degradation products.

Highly entangled hydrogels with degradable crosslinks

This paper studies a polymer network in which crosslinks are degradable but polymer chains are not. We show that entanglements markedly enhance the mechanical properties of the polymer network before degradation and slow down degradation. We synthesize polyacrylamide hydrogels with disulfide crosslinks. In a precursor of a low water-to-monomer molar ratio and low crosslinker-to-monomer molar ratio, the monomers are crowded and the resulting polymer chains are long, so that the entanglements greatly outnumber crosslinks. The as-synthesized hydrogels are submerged in pure water to swell to equilibrium. We show that entanglements enhance the swell resistance of the hydrogel, as well as stiffen and toughen the hydrogel. We further show that entanglements slow down degradation when the hydrogel is submerged in an aqueous solution of cysteine. This work demonstrates that entanglements substantially expand the properties space of degradable polymers.

Controlling primary chain dispersity in network polymers: elucidating the effect of dispersity on degradation.

Although dispersity has been demonstrated to be instrumental in determining many polymer properties, current synthetic strategies predominantly focus on tailoring the dispersity of linear polymers. In contrast, controlling the primary chain dispersity in network polymers is much more challenging, in part due to the complex nature of the reactions, which has limited the exploration of properties and applications. Here, a one-step method to prepare networks with precisely tuned primary chain dispersity is presented. By using an acid-switchable chain transfer agent and a degradable crosslinker in PET-RAFT polymerization, the in situ crosslinking of the propagating polymer chains was achieved in a quantitative manner. The incorporation of a degradable crosslinker, not only enables the accurate quantification of the various primary chain dispersities, post-synthesis, but also allows the investigation and comparison of their respective degradation profiles. Notably, the highest dispersity networks resulted in a 40% increase in degradation time when compared to their lower dispersity analogues, demonstrating that primary chain dispersity has a substantial impact on the network degradation rate. Our experimental findings were further supported by simulations, which emphasized the importance of higher molecular weight polymer chains, found within the high dispersity materials, in extending the lifetime of the network. This methodology presents a new and promising avenue to precisely tune primary chain dispersity within networks and demonstrates that polymer dispersity is an important parameter to consider when designing degradable materials.

PH and Reduction Dual-Responsive Nanogels as Smart Nanocarriers to Resist Doxorubicin Aggregation.

The use of smart nanocarriers that can modulate therapeutic release aided by biological cues can prevent undesirable cytotoxicity caused by the premature release of cytotoxic drugs during nanocarrier circulation. In this report, degradable nanocarriers based on pH/reduction dual-responsive nanogels were synthesized to encapsulate doxorubicin hydrochloride (DOX) and specifically boost the release of DOX in conditions characteristic of the cancer microenvironment. Nanogels containing anionic monomer 2-carboxyethyl acrylate (CEA) and N,N′-bis(acryloyl)cystamine (CBA) as a degradable crosslinker have been successfully synthesized via photoinitiated free radical polymerization. The loading process was conducted after polymerization by taking advantage of the electrostatic interaction between the negatively charged nanogels and the positively charged DOX. In this case, a high drug loading capacity (DLC) of up to 27.89% was achieved. The entrapment of DOX into a nanogel network could prevent DOX from aggregating in biological media at DOX concentrations up to ~160 µg/mL. Anionic nanogels had an average hydrodynamic diameter (dH) of around 90 nm with a negative zeta (ζ) potential of around −25 mV, making them suitable for targeting cancer tissue via the enhanced permeation effect. DOX-loaded nanogels formed a stable dispersion in different biological media, including serum-enriched cell media. In the presence of glutathione (GSH) and reduced pH, drug release was enhanced, which proves dual responsivity. An in vitro study using the HCT 116 colon cancer cell line demonstrated the enhanced cytotoxic effect of the NG-CBA/DOX-1 nanogel compared to free DOX. Taken together, pH/reduction dual-responsive nanogels show promise as drug delivery systems for anticancer therapy.

PET-RAFT Increases Uniformity in Polymer Networks.

Photoinduced electron/energy transfer (PET)-reversible addition-fragmentation chain transfer polymerization (RAFT) and conventional photoinitiated RAFT were used to synthesize polymer networks. In this study, two different metal catalysts, namely, tris[2-phenylpyridinato-C2,N]iridium(III) (Ir(ppy)3) and zinc tetraphenylporphyrin (ZnTPP), were selected to generate two different catalytic pathways, one with Ir(ppy)3 proceeding through an energy-transfer pathway and one with ZnTPP proceeding through an electron-transfer pathway. These PET-RAFT systems were contrasted against a conventional photoinitated RAFT process. Mechanically robust materials were generated. Using bulk swelling ratios and degradable cross-linkers, the homogeneity of the networks was evaluated. Especially at high primary chain length and cross-link density, the PET-RAFT systems generated more uniform networks than those made by conventional RAFT, with the electron transfer-based ZnTPP giving superior results to those of Ir(ppy)3. The ability to deactivate radicals either by RAFT exchange or reversible coupling in PET RAFT was proposed as the mechanism that gave better control in PET-RAFT systems.